7 eS ELL HAMBERL AIN
LiftMaster PROFESSION A L MODEL 33LM 3-BUTTON REMOTE CONTROL TRANSMITTER ea) garage door opener. The other push buttons can be used to operate another opener and/or light control product. The ad Foe Remote Control Transmitter can also be used with a 423LM 3-channel receiver and a 3-button door control to operate a commercial door opener in open, close; and stop mode (as explained on side 2). To match or change the code in the peed Locate the code. switches in both the new and the original transmitters. The new transmitters code switches can be found by sliding the battery compartment cover back. Place transmitters side by side as shown (Figure 1) and set switches in all transmitters to matching positions
(+,0,). Use a pen or screwdriver to slide the code switches. Figure 1 Match code switches (2-9) between oid transmitter and new transmitter (Code switch
#1 on the 3-button remote control is dormant) NOTE: Code switch #1 on Figure 2 the 3-button transmitter is dormant, when used with Foy sie i/o orto 8) transmitter. Set code switch #1, in the Fee [om Cem RL an to match the push button selected on the 3-button transmitter (Figure 2). Push Buttons Replacement Parts Remote case housing
(circuit board not included) Visor clip 12V battery See Lee The green push button is recommended for use with a To prevent possible SERIOUS INJURY or Aicelan moving gate or garage door:
* ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote control transmitters.
* Activate gate or door ONLY when it can b seen clearly, is properly adjusted, and there are no obstructions to doar travel.
* ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of maving gate or door. Programming the opener 1.Press and release the learn button located on the back panel of the motor unit. The learn:indicator light wilkglow _ steadily for 30 seconds. , 2. Within the 30 Peter window, press and hold the button on the hand-held remote. 3. The unit will either activate or the opener light bulb will blink signifying it has learned the code. If your unit has code switches:
1. Using a step ladder climb up to the back of your motor unit. Check the code switch settings on the back of the motor unit. Use a pen or screw driver to set the Code switches on the back of the transmitter to match the code switches on the back of the motor unit. Once the code switches have been set push the transmitter button to activate your unit. Replacing the transmitter battery Install the control station and receiver where the door is NIC MmOMe EN Abel UROLOGIC LUCCA b ;
receiver is used to activate a commercial door opener, a To prevent possible SERIOUS INJURY or DEATH:
reversing edge MUST be installed on the bottom of the door. AR aVacw ern Cimicela elt Failure to install a reversing edge under these circumstances 5 , F iatel 7 may result in SERIOUS INJURY or DEATH to persons trapped Se A ce beneath the door. The 12 voit battery should 5 pi 7 produce power for 1 year. To To use the transmitter with a 3-channel replace the battery, slide the receiver and 3-button door control to Cae ea tenes operate a commercial door opener Dispose of old batteries properly. NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS. Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the POR IC eM ON UIE Cr ecm mc eel M CULE CCU 4 US aC) must accept any interference received, including interference that may cause undesired operation. FOR SERVICE DIAL OUR TOLL-FREE NUMBER:
1-800-528-2817 1. Use a screwdriver to pry open the receiver cover (see illustration).
[Ov PaO HEE COS aa OM Lc) N.C. position (otherwise the opener will not operate). Verify this setting. 2. Select a remote control push button to STOP the opener. (RED is recommended.) Press and hold the selected remote push button. 3. Then press and release the learn button labeled A on the receiver. The adjacent indicator light will FLASH. Release the remote push button. Repeat the procedure above with the yellow remote push button and receiver learn button B to: program the CLOSE operation; andagain with the green remote push button and receiver learn button C to program the OPEN function of the opener. Return the front cover to the receiver.
(For this application, code switch settings need not be changed.) NOTE: If a remote control push button is not pressed RU aeL ME Le ecleMm eU eel) oe CRU selected learn button will turn OFF. In that case, repeat the programming.
2004, The Chamberlain Group, Inc. *
114A1938E All Rights Reserved Printed in Mexico