MODEL MC100 UNIVERSAL GARAGE DOOR MINI REMOTE CONTROL The Universal Garage Door Mini Remote Control can be programmed to activate up to two products, such as a garage door opener, MyQ light controls, gate operator, or commercial door operator. Each button on the remote control works independently of the other and must be programmed separately. The images throughout this manual are for reference only and your product may look different. The Universal Garage Door Mini Remote Control can be programmed to operate with different brands of garage door openers. It is compatible with most garage door opener systems manufactured by Chamberlain , LiftMaster , Sears Craftsman , Garage Master , Genie , Linear , Stanley , Overhead Door , Wayne Dalton , Moore-O-Matic , Do-It , Master Mechanic , Raynor , and True Value . To prevent possible SERIOUS INJURY or DEATH from a moving gate or door:
ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote control transmitters. Activate gate or door ONLY when it can be seen clearly, is properly adjusted and there are no obstructions to door travel. ALWAYS keep gate or door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door. STOP Read instructions thoroughly BEFORE beginning. If using the Universal Garage Door Mini Remote Control with residential door openers, the remote control must be used only with door openers manufactured after 1993 that utilize photoelectric sensors. The photoelectric sensors are always located on or near the bottom of the door track. The Universal Garage Door Mini Remote Control is compatible with the following brands, which use a program/learn button:
Type/Color of Garage Door Opener Program/Learn button Brand Mega-Code Linear Orange/Red Chamberlain*
Purple Chamberlain*
Green Chamberlain*
Genie Overhead Door Intellicode Genie** Overhead Door Intellicode Stanley Chamberlain*
Wayne Dalton Secure Code Yellow Rolling Code Year
'97-Current
'97-'03
'05-Current
'93-'96
'95-Current
'93-Current
'98
'11-Current
'99
* LiftMaster , Do-It , Master Mechanic , Raynor , True Value and Sears Craftsman are compatible with Chamberlain technology.
**Visit www.chamberlain.com/MC100 for Genie Intellicode II instructions. PROGRAMMING IMPORTANT: The remote will activate your door or gate during programming. Ensure door is clear of ALL obstructions. 1 2 3 4 5 Start with your garage door closed. Press and hold bottom button on the remote control until the blue LED stays solid (approximately 10 seconds) then release the button. LED Bottom Button Press and release the Program/LEARN button on your garage door opener. Program/
LEARN Button On the remote control, press and release the button that you would like to program twice. The blue LED will blink and the remote control will begin sending the pre-
programmed codes to the garage door opener. Transmission can take up to 45 seconds. When the garage door opener activates, immediately press and release either of the buttons on the remote control to confirm the code and exit programming. TEST Test the remote control by pressing the button you programmed in step 4. If the garage door opener does not activate, repeat the programming steps or visit www.chamberlain.com/MC100 for additional instructions. BATTERY NEVER allow small children near batteries. If battery is swallowed, immediately notify doctor. To prevent possible SERIOUS INJURY or DEATH:
To reduce risk of fire, explosion or chemical burn:
Replace ONLY with 3V CR2032 coin batteries. DO NOT recharge, disassemble, heat above 212F (100C) or incinerate. Dispose of batteries properly. Replace ONLY with 3V CR2032 coin batteries. Screw Battery NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS. Tested to comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation. Need Help?
Go to www.chamberlain.com/MC100 or call 1-800-442-1255 All trade names used herein are trademarks of respective manufacturers listed. 2015, The Chamberlain Group, Inc. All Rights Reserved 114A4845