- (i!
Part No. A}R2014X000 | RE 014X001 | RE
[E]R2014x005 | Rt
[FL NA_ [Rt
[S|
H CGB TC 2014x011] AL
Description
(ERE 12V POWER S
[ERE POWER LEAD ORD GRIP JHESIVE BLOCKS UPPLY. YS, CANNER SISTIENS, ng Replace ost cases you will Revere 2014 rece actory. The steps an already existir vers, if desired. ivers previously f
>K/SILENCER whil inue holding unti ir a receiver toa iplug Transmitter sert the batterie:
ENSOR SIGNAL in ug in the transmi nce units are bot how the current 1e receiver cant |
together. Once tl matically pair anc s. For the best re
- proximity to eac conds after the r ment or A not need to pair 2iver and transmi below are for pa ig transmitter or aired will need t je inserting the bs
| all lights flash. transmitter:
s into the receive
\dicator will flash itter ind, the alarm be status of the salt find a sensor to p he receiver finds 1 the OK indicato sults when pairin h other. Units ca eceiver powers u aaSSS dditional Re the units out of |
tter will be pairec iring a replaceme for adding additi o be un-paired. H atteries into the r r. An alarm will s when the receiv eps once and the level sensor. air with, all indic:
a sensor the two r will flash and th 1g units, stay with in only pair withir p. 2ceivers the box. d from ont receiver onal lold eceiver. ound and er is ready.
> receiver ators will will e alarm vin n the first Frequently Asked Questions and Answers
- Ladded salt, but my receiver is still reading low salt. To conserve battery life, the receiver sleeps and wakes up every 30 minutes. It could take up to 30 minutes for the reciever to update after salt is added. To immediately update the status, press the CHECK/SILENCER button.
- My receiver shows low salt, but its not beeping. The audible beeps have been turned off. See note 2 on Pg. 4 for enabling the audible beeps.
- My receiver is showing no signal in an area that was fine before. Transmitter doesnt have power, or it is periodically picking up noise from another device in the home. Wait to see if status returns or move to an alternate location.
- My receiver doesnt have any lights on. The receiver is currently in sleep mode, or the batteries are dead. Press CHECK/SILENCER button, if green indicator appears everything is fine. If no lights appear when CHECK/ SILENCER is pressed the batteries will need replaced.
- My transmitter doesnt fit snuggly over my brine well. The transmitter was designed to fit 4 brine wells. However, a less common size is 3.5 and adapters are Included for them as well.
~See Back Page For Installation location
- My receiver periodically flashes a green light. Everything is okay and your salt level is adequate. The receiver goes to sleep to conserve battery life and wakes up every 30 minutes to check the status. For the one minute it is awake every half hour, the receiver displays the status. Please note you can check the status at any time by pressing the CHECK/SILENCER button. For an Installation Tutorial video please visit:
http: //www.youtube.com/watch?v=-UGf0AGef8U Transmitter Installation 1.) Attach Revere Transmitter (D) to Paddle (C). 2.) Slide Transmitter with Paddle over brine well.
-Note: The transmitter should fit snug on the brine well. Adapter (H) may be required if its loose. (See Back Page For Drawing) 3.) Drill 9/16 size hole into the side of the brine tank. Make sure hole is beside the same side as the power lead. As shown in Figure A 4.) Pull power lead (F) through hole. see Figure A ane 1. Hold down Cord Grip 2. With Cap held, press into hole. Brine Well Figure A Figure B 5.) With the power lead fully through, place cord grip (G) over the power lead, close to the brine tanks outer edge. Then push the cord grip through the hole drilled in step 3. see Figure B 6.) After plugging in power supply (E) to an outlet, connect the transmitters power lead (F) to the power supply. 7.) Add salt, making sure paddle is flush against the brine well and you're pouring towards it so that salt doesnt get between the paddle and the brine well. 8.) Place elastic band (B) over the top of the transmitter and replace brine tank lid.
-Your Revere transmitter is now ready to go!
(Turn the page for receiver setup instructions) Receiver Setup 1.) Go to the desired receiver location with the unit. 2.) Remove tab from battery door. 3.) Then press the CHECK/SILENCER button. If location is adequate, the green OK indicator light will flash. If the No Signal red indicator is present, you will need to move to an alternate location where a signal is received. Testing & Normal Operation Pressing the CHECK/SILENCER button allows users to quickly test the connectivity between the receiver and transmitter. Users are able to use this to find the optimal location to place the receiver or check the functionality of the product. Under Normal Operation the Receivers LED lights will remain off and the receiver will wake up every 30 minutes. The OK indicator will blink for one minute every half hour when the receiver wakes up and checks status. WARRANTY INFORMATION Chandler Systems Inc. warrants this product to be free of defects in workmanship and material, under normal use conditions, for a period of 90 days from the original date of installation. Should this product fail, please return it to the point of purchase. Chandler Systems inc. will, at its discretion, replace product with out charge. This decision is subject to verification of defect upon delivery to the factory service center. The product must include proof of purchase that consists of the date of installation. Indication Lights and Audible Beeps LOW BATTERY: Red indicator will flash when the receiver's batteries are low. ADD SALT: Yellow indicator will flash when theres not enough salt to keep the paddle flush with the brine well. NO SENSOR SIGNAL: Red indicator will flash when the signal is blocked or weak and can not reach the receiver. It could also mean theyre not paired. OK: Green indicator will flash when the salt level inside the brine tank is fine. Audible Beep: Sounds during the add salt, low battery, no sensor signal condition an audible beep will be produced once every minute.
-Note:
1.) Pressing the CHECK/SILENCER button will mute the receiver for 48 hours and will return if no salt is added within that time. 2.) Hold in CHECK/SILENCER to enable/disable the audible beeps permanently. Holding it in for 5 seconds until you hear one beep indicates them being disabled. If two beeps are heard, they are enabled. A) j a Receiver CC IDs:
Receiver: SWP-R2C ransmitter: SWP-R2C These devices c Operation is suk hese devices mz hese devices 1 ncluding interfere
>hanges or moc arty responsible authority to opera NOTE: These eq omply with the li o Part 15 of the provide reasonat nN a residential Ise and can rac nstalled and use ause harmful tJowever, there i secur in a partic ause harmful in'
vhich can be det yn, the user is er yy one or more of
- Reorient or rel
- Increase the eceiver.
- Connect the ec rom that to whict
- Consult the de:
or help. stent Pending ev. 4.2 4R1 14R3 omplies with Pa ject to the follc ay not cause har nust accept ar 2nce that may cz lifications not e>
2 for complianc ite the equipmen'
juipments have |
imits for a Class FCC Rules. The le protection ag installation. The:
diate radio freqt d in accordance interference to Ss no guarantee ular installation. terference to rac termined by turni
\couraged to try f the following me ocate the receivil separation betw quipment into an 1 the receiver is c aler or an experi rt 15 of the FC wing two condi mful interference y_ interference ause undesired pressly approve e could void tl to been tested and B digital device, ase limits are de ainst harmful int se equipments |
yency energy at with the instructi radio commu that interferenc _ If these equipr lio or television |
ing the equipme!
to correct the int 2asures:
ng antenna. veen the equipr outlet on a circui sonnected. enced radio/TV t
-C Rules. tions: (1) 2, and (2) received, operation. 2d by the he user's
| found to pursuant signed to erference generate, nd, if not ions, may nications. e will not ments do reception, nt off and erference nent and it different echnician