d S G - 2 0 0 0 Users manual d Contents 1. Screen description. 1.1. 1.2. Standby screen. Certification Success / Failure screen. 2. administrator Card Registration 2.1. administrator Card Registration. 3. User Management. 3.1. 3.2. User Registration Delete user User Manual SG-2000 Time / Date Administrator menu Connection Status 1 Standby screen 1. 1 Standby screen
<Figure 1> Standby screen Attendance User Manual 1 Standby screen
- <Figure 1> is a standby screen. <Figure 1> shows the information of the time and date, the state of waiting for authentication. Authentication methods (fingerprint, RFID, W-KEY) authentication when you attempt to do one of the screen lights up.
[Table 1] Function description Name description Date / Time displays the time and date. Administrator menu Move to the Administrator menu. Connection Status Shows the connection to the server Attendance Apply for Attendance. User Manual 1 Standby screen 1. 2 Successful / failed authentication screen Successful authentication screen Authentication failed screen User Manual 2 Administrators card registration 2. 1 Administrators card registration
-Administrator card is used when a user registered in the SG-2000 series.
- Registration procedure [Table 2]
[Table 2] Administrators card registration procedure 1 2 3 Check. After the terminal installed the green LED emits light when the user information is not present. If this check, the tagging device in the RFID card is included in the set. If the blue LED flashes a success.
- The administrator card is used for the purpose of registration.
- Administrator card can apply for only one card when the stand alone.
- When the network mode, look at the S/W manual. User Manual 3. User administration 3. 1 User Registration
- Registration procedure [Table 3-1] [Table 3-2]
Each of the registration process If the ID is registered successfully, the LED is blinking momentarily changed to blue and back to green. When lead to problems with registration ID is shown in red, it LED blinking returns to green.
[ 3-1]
1 When tagging an administrator card, an RFID key card user registration status immediately. 2 Register your ID 3 Register your password. 4 First fingerprint registration User Manual 3.
[ 3-2]
5 Second fingerprint registration 6 Third fingerprint registration 7 RFID key card registration 8 W-Key registration 9 Confirmation page Modify User, Delete and other terminal set is only available in network mode. User Manual 3. User administration 3. 2 Delete user 1 2 When tagging an administrator card, an RFID key card user registration status immediately. When tagging an administrator card once more in the state 1 is the clear mode. 3 Delete All Click Delete All button 4 Confirmation page Each of the registration process If the ID is registered successfully, the LED is blinking momentarily changed to blue and back to green. When lead to problems with registration ID is shown in red, it LED blinking returns to green. Federal Communications Commission (FCC) Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.