FCC ID: 2AOTU-KDH243B-XXX Handset

KDDY109B+KDH243Bonecontroltwocontrolsystemfunction I Systemconnectiondiagram manual II Productlist Theserial number Name(code name) Modeland Specificatio n KDH243 1 2 3 4 5 6 7 Handcontrol device Controlbox KDDY109 supply KDDY01B Power box PushRod1(H) KDYJT014 PushRod2(F) KDYJT014 Lampwith DY056 Vibratingmotor ZYD060 note Num ber 1 1 1 1 1 1 2 III PerformanceParameters 1. Controlboxperformanceparameters:

Inputvoltage AC110240V 50/60Hz Ratedoutput(single channel) 2. Manualcontrollerperformanceparameters:

29VDC/5A(10%worksystem,maximum2minutesofcontinuous workand18minutesofstop) Inputvoltage Numberofkeys 4.5V 14 1 OutlineofKDDY109B OutlineofH243B 2 IVManualcontrollerkeyfunctiondescription 3 1 Function of hand control device:

The name function note serial number 1 Preset 1, K1 light touch press, the push 1 Press any key to position rod running to a fixed stop the push rod position (Leisure mode) stop during operation;

(head push rod travel: 42mm, 2 Perform the head leg push rod travel: 43mm). putt first, then the 2. Press K2 gently and stop the leg putt push rod running to a fixed position (Incline tilt mode)

(head push rod travel: 48mm, leg push rod travel: 32mm) 3. Press K5 gently and stop the push rod running to a fixed position (zero gravity mode)

(head push rod travel: 23mm, leg push rod travel: 37mm) 4, K6 touch press, the putter does not move. 5. K10 gently presses the push rod to a fixed position (Anti-

Snore mode) and stops (head push rod stroke: 18mm, leg push rod stroke: 0mm). 2 Place of Press and hold 1 The position can be memory 6+1/6+2/6+5/6+10 at the modified by the same time. After the backlight customer according to 4 flashes for 3 the itinerary after seconds, the control box delivery; Hold down will remember the current 6+1/6+2/6+5/6+10 position of the push for 3S to remember the rod; At the same time, the current position buzzer buzzes once and the

(overwriting the backlight is off. Press K1, previous position); At K2, K10 or K5 again, and the same time, the the push rod will run to control box buzzes once the corresponding memory and the backlight position;

flashes three times. 2 Press any key to stop the push rod during operation;

3 Push bar 1 Press K3, push rod out,

(head bar H) release will stop;

lift Press K4, push rod retract, release will stop;

4 Putter 2 Press K7, push rod out,

(leg putter release will stop;

F) lift Press K8, push rod retract, release will stop;

5 Putt 1 and putt 1. Long press K9 and pull 1. Short press is 2 (head back putter 1 and putter 2 at invalid and leg) fall the same time after 3S;

together 2. During the operation 2. During the operation of the push rod, press of the push rod, you can any key to stop the push release the key (Note:

rod, except Flat(K9) and press any key and the push Frogram (K6). 5 rod will stop, except Flat

(9) and Frogram (6). 6 Vibration mode 1, short press K14, each Mode 1: intermittent switching and vibration mode switch vibration with a slower vibration starts from 1,123 cycle in frequency;

intensity turn;(Note: The Mode 2: intermittent selection corresponding indicator vibration with higher light is highlighted) frequency;

2, long press K14, vibration Mode 3: intermittent mode automatically switch vibration with the

(1S fastest frequency;

at each interval), release The three modes are will stop, to stay in the switched sequentially;

current gear vibration mode If the operation;

change button is not operated within 15 minutes, the vibrating motor will automatically shut down

(select the motor strength for the last time and start to calculate the time). 7 3 Short press K12, The vibration motor can vibration motor enhancement be opened by the rise

(intensity button of the vibration is divided into four motor (12) or by gears), each time press pressing the vibration gradually strengthen. mode (14) (Note: the 6 4 Short press K13, the intensity of the vibration motor weakens (the vibration motor is in strength is divided into gear 3 at this time). four gears), and gradually decreases with each press, and the motor stops with the fourth press. 5 Short press K11 to stop the vibrating motor. 8 Lamp with K15 Gently press (the button on the back of the hand controller), and the light belt will turn on. Press it again, and the light belt will turn off. 9 pairing Method 1: Long press the pairing button of the control box for 3 seconds to enter the pairing state;

Press the hand controller K3 and K7 within 15 seconds, hold for 3 seconds, the control box buzzes once, the pairing button stops blinking, and the background light of the hand controller flashes for 3 times, the pairing is successful;

7 Method 2: Power on the control box again after 5 seconds of power failure, and the control box enters the pairing state; Press the hand controller K3 and K5 within 15 seconds, hold for 3 seconds, the control box buzzes once, the pairing button stops blinking, and the background light of the hand controller flashes three times, the pairing is successful;

10 Clearing Method 1: Long press the matches pairing button of the control box for 3 seconds to enter the pairing state; Press the hand controller K4 and K8 within 15 seconds and hold for 3 seconds. The control box buzzes once, the pairing button stops blinking, and the background light of the hand controller flashes for 3 times. The pairing is successful. Method 2: Power on the 8 control box again after 5 seconds of power failure, and the control box enters the pairing state; Press the hand controller K4 and K8 within 15 seconds and hold for 3 seconds. The control box buzzes once, the pairing button stops blinking, and the background light of the hand controller flashes for 3 times. The pairing is successful. 11 factory data Method 1: Long press the reset pairing button of the control box for 3 seconds to enter the pairing state; Press the hand controller K3 and K8 within 15 seconds and hold for 3 seconds. The control box buzzes once, the pairing button stops blinking, and the background light of the hand controller flashes quickly for 3 times. Method 2: Power on the control box again after 5 9 seconds of power failure, and the control box enters the pairing state; Press the hand controller K3 and K8 within 15 seconds and hold for 3 seconds. The control box buzzes once, the pairing button stops blinking, and the background light of the hand controller flashes quickly for 3 times. 12 One control When the manual controller two is paired with the control box A, it can be paired with the control box B, so that one controller can control the action of the control box at the same time V Precautions 1, before use, please be sure to correctly connect according to the system connection diagram, and then switch on the main power supply;

2, children, the elderly and the disabled, please use under supervision;

3. Do not plug or remove any connection line when the power supply is switched on, which may cause operation function failure. In this case, you can cut off the main power supply and reconnect it after about 30 seconds. 4. Before the first use, the wireless hand controller should be paired with the control box. See Step 9 for the specific method;

5, the first use needs to be reset, to ensure that the memory position is accurate, the specific method to operate K9;

6, the control box can be paired with two hand controllers, if paired with the third, the first will be cleared. 7. Please replace the battery of the manual controller in time. If it is not used for a long time, the battery should be taken out. 10 VI warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1)Thisdevicemay notcauseharmfulinterference,and(2)thisdevicemustacceptany interferencereceived,includinginterferencethatmaycauseundesiredoperation. FCCwarning:

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user'sauthoritytooperatetheequipment. Note:ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interferenceinaresidentialinstallation.Thisequipmentgeneratesusesandcanradiateradiofrequencyenergy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turningtheequipmentoffandon,theuserisencouragedtotrytocorrecttheinterferencebyoneormoreofthe followingmeasures:

Reorientorrelocatethereceivingantenna. Increasetheseparationbetweentheequipmentandreceiver. Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected. Consultthedealeroranexperiencedradio/TVtechnicianforhelp. ThedevicehasbeenevaluatedtomeetgeneralRFexposurerequirement.Thedevicecanbeusedinportable exposureconditionwithoutrestriction. Preparation: Review:

11

(Changzhou Kaidi Electrical Inc.) Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: 2AOTU-KDH243B-

XXX Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type Block Diagram, Schematics, Operational Description File Name Block Diagram.pdf, Schematics.pdf, Operational Description.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Pursuant to DA04-1705 June 15, 2004 of the Commissions public notice, we also request temporary confidential treatment of information accompanying this application, Short-Term Confidentiality for 180 days as outlined below:

Exhibit Type External Photos, Test Setup Photos, Manual File Name Test Setup Photos.pdf, Manual.pdf, External Photos.pdf Sincerely, Qin Yin/Manager Changzhou Kaidi Electrical Inc.

Difference Statement KDH243B-XXX The only difference between the models in each series is the nomenclature. The PCB schematic diagram, PCB Layout, appearance, etc. are all the same. The first and second "X"

represent the customer code, and the third "X" represents the version number. We have prepared model KDH243B-001 for RF testing. FCC ID: 2AOTU-KDH243B-XXX Qin Yin/Manager Changzhou Kaidi Electrical Inc.

(Changzhou Kaidi Electrical Inc.) Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: November 14, 2022 SUBJECT: FCC Application for FCC ID: 2AOTU-KDH243B-XXX To Whom It May Concern:

We, the undersigned, hereby authorize Tony Wei at EMTEK(NINGBO) CO., LTD. on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by EMTEK(NINGBO) CO., LTD. on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Qin Yin/Manager Changzhou Kaidi Electrical Inc.