Users Guide of the Happy Call Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void users authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. CHARMSORI Electric Telecom Co., Ltd. Page 1 of 9 1. Product Description Thanks for purchasing Happy Call System. This device is wireless calling system which adopted High-performance CPU(Central Processing Unit) of Pro-Chips Company. Using Wireless Transmitter and Receiver, User can communicate each other without talking by face to pace, so this device is very useful at restaurants. 2. Product Details 1) Receivers
- Front View
- Rear View Page 2 of 9 2) Transmitter
** Repeator and Adaper is optional. 3. Operation Instruction 1)Receiver MC-6000 Series
- When power is on, the receiver conduct self-diagnosis with music is being played and the display blinking in order.
- When a table number is input, it appears on the screen and the number goes off after time setup.
- Input numbers can be memorized(maximum 10) and replayed. Page 3 of 9 MC-7000 Series
- When power is on, the receiver conducts self-diagnosis with music is being played and the display blinking in order.
- When a table number is input, it appears on the screen and the number goes off after time setup.
- When several numbers are input, they appear moving from the left to the right in the order of input. 2) Transmitter (commonly used in MC-6000 & 7000 Series) 3) Repeator (commonly used in MC-6000 & 7000 Series) 4. Installation 1) Receiver Avoid humid places. Install it at least 3m away from wireless devices(such as wireless phones) and the places of big magnetism(such as speakers). Check the electric power source and voltage of the place where it is installed(220V). The antenna is regulated at the angle ranges of 0 ~45 and a 3-stage antenna is used. When power is on, check the self-diagnosis(refer to 1-3). 2) Transmitter Install it at least 3m away from the receiver. In case batteries(A23, 12V) are exchanged, insert identical batteries after loosening screws of the backside(pay attention to +,-). Batteries should be exchanged when the blinking of the lamp on the top of the transmitter conspicuously slows down. Page 4 of 9 3) Repeator (In case of installation) The translator, as a wireless one, can be installed by the only power connection without additional electric wire. The channel choice of the translator is the same as the channel regulation of the backside receiver(SW1, SW2 and SW3 are turned on always). The translator should be installed in places near the regions where transmission is not available. Page 5 of 9 5. Option set-up 1) Receiver SELECT S/W No. 1-4 have their own functions. When options are changed, the power of S/W should be turned on again after 4-5 seconds'
off to make the receiver recognize the change. SELECT S/W Functions(Receiver) Page 6 of 9 2) Transmitter Switches for number choice are from No.1 to No.7, and switches for channel choice are from No.1 to No.5. Number Choice Page 7 of 9 6. Check-point when abnormal operation When this product is operated abnormally, please make inquiries at the A/S or consumer consultation office after checking following points.
<In case of malfunction in the receiver>
1. Numbers are displayed but sound is not working. Check if sound regulation is setup at minimum and check if the choice switch No.1 of the receiver is turned off. 2. The state of reception is not good. Regulate the location of an antenna(angle ranges of 0~45 to the direction of the transmitter from the place of the installed receiver, and only the use of the thick side 3-stage antenna). Transfer the current location of the receiver because it is influenced by surrounding wireless devices. 3. A place is displayed as a call region without the press of call button. Change the channel of the transmitter and receiver because it could happen in case more than 2 transmitter buttons are pressed at the same time and identical system or similar prod neighborhood(refer to Clause 3 about the channel change).
<In case of malfunction in the transmitter>
1. In case the light on the top of the transmitter is not turned on : Poor contact of batteries of the transmitter and exchange 2. In case the light is OK but the transmitter is not working : The decrease in the transmission sensitivity or battery problems. ucts are installed in the Page 8 of 9
<In case of malfunction in the Repeator>
1. Power lamp is not working : Poor contact of connection wire or disconnection 2. Transmission and receipt are not available : Check the green/yellow lamps under the translator. 3. Receipt is OK when the green lamp is turned on and off, and transmission is OK when the yellow lamp is turned on and off. 7. Specification 1. Power : Max 1.2 W, Normal 0.8 W 2. Input Voltage of Receiver : AC220V, 60 Hz / DC 12V 850 mA ~ 1 A 3. Channel number displayed : 128 4. Channel Quantity : 32 5. Temperture : -10 ~ + 60 6. Transmitter power : DC 12V 33 mA (Alkaline Battery) Page 9 of 9