Features and Functions Guide H3 Bluetooth Handsfree Headset TURNING HEADSET ON/OFF To turn your headset on, press and hold the Call button until the indicator light flashes. Then, release the button. To turn your headset off, press and hold the Call button until the indicator light flashes rapidly and then turns off. WEARING THE HEADSET 1 2 3 Open the earhook. Loop the earhook over your ear. Press the headset to your ear. CHANGING FOR USE ON OTHER EAR You can wear your H3 headset on your left or right ear. The headset comes ready for the right ear. To change the headset for the left ear:
CHANGING VOLUME BUTTON ORIENTATION If you change your headset to wear on the other ear, you can also change the orientation of the volume buttons. 1 Open the earhook 90 degrees from the headset. 1 2 Turn the headset power off. Press the Call button along with the Volume button you want to assign as
"volume up" button until the indicator light flashes twice. The headset power turns on. IMPORTANT:
Be sure to first follow the Quick Start Guide on the reverse side of this guide to complete initial setup of your H3. Call Button Volume Buttons 2 3 3 4 1 Open Earhook 2 Pull Earhook Up Call Button Flip the headset over. Gently lift and pull the top of the earhook up and off the upper hinge pin. Then, pull it away to remove it. D R A F T Action Press and hold the Call button Press and hold both Volume buttons Press and hold the Call button until you hear a beep Tap the Call button Hook the bottom of the earhook onto the lower hinge pin, then lift and pull the top of the earhook over the upper hinge pin.
The indicator light provides information about your headset status. Headset Indicator
On (steady) Off
MAKING CALLS CONTINUED Headset Status Charging Charging complete INDICATOR LIGHTS MAKING CALLS With the Charger Plugged In With No Charger Plugged In Hinge Pin 4
Function Make a voice dial call
End a call
Receive a call
Reject a call
Redial last call
Answer a second
incoming call
Action Tap the Call button and speak the
name after the tone Tap the Call button Tap the Call button Press and hold the Call button until you hear a beep Press and hold the Call button until you hear a beep Press and hold the Call button (places first call on hold) Note: Your H3 supports both Handsfree and Headset Profiles. Accessing call functions depends upon which profile your phone supports. See your phone's user's guide for more information.
Function Toggle between two active calls
Join a 3-way call
Put an active call on hold or resume a call on hold Transfer a call from the phone to the headset Disable or enable the indicator light
Mute or unmute a call
Note: Some features are phone/network dependent. Press and hold both Volume buttons for 3 to 4 seconds Tap both Volume buttons
Headset Indicator
Off
On (steady) 10 rapid flashes
Slow pulse
Quick flash
Note: After 5 minutes of inactivity, the light stops flashing to conserve power, but the headset remains in standby mode. Headset Status Power off Pairing mode Pairing successful Connected
(on a call) Standby
(not on call)
AUDIO TONES The audio tones provide information about your headset status.
Out of range Headset Status Volume at minimum Audio Tone Single high tone when pressing volume button or maximum Five rapid high tones Low battery repeated every 60 sec. No audio indications; deteriorating quality Incoming call Ring tone
Pairing confirmation Single high tone Voice activation Single low tone
Voice tag not Dual high/low tone recognized
End call Single high tone Phone network Low to high tone not available
Two ascending tones Mute enabled Two descending tones Mute enabled
FEDERAL COMMUNICATIONS COMMISSION This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.