E30(915T20S)-User Manual-V1.0 Website www.cdebyte.com/en E30(915T20S)-User Manual-V1.0 Contents 1. Introduction................................................................................................................ 2 1.1 Feature............................................................................................................... 2 1.2 Electrical Parameters.........................................................................................2 2. UART functional description (default).......................................................................4 2.1 Fixed transmission.............................................................................................4 2.2 Broadcast transmission......................................................................................4 2.3 Broadcast address.............................................................................................. 4 2.4 Monitoring address............................................................................................4 3. Functional description................................................................................................ 5 3.1 Pin definition..................................................................................................... 5 3.2 Connect to MCU............................................................................................... 6 3.3 Reset.................................................................................................................. 6 3.4 AUX description................................................................................................6 4. Customization.............................................................................................................8 5. About us......................................................................................................................8 Page 1 of 8 Technical Support : support@cdebyte.com E30(915T20S)-User Manual-V1.0 Website www.cdebyte.com/en 1. Introduction 1.1 Feature E30(915T20S) is a 100mW wireless transceiver module(UART), half-duplex& transparent transmission, which operates at 907~922.5MHz(default: 915MHz), TTL Level, compatible with the 3.3V and 5V IO port. The module has the function of data encryption & compression. The data of the module transmitted over the air features randomness. And with the rigorous encryption & decryption, data interception becomes pointless. The function of data compression can decrease the transmission time & probability of being interfered, while improving the reliability & transmission efficiency. No. Usage Description Ultra-low power consumption Fixed transmission It supports WOR to reduce overall power consumption. In power-saving mode(Mode 2), it can regulate overall power consumption by setting receiving response delay; The maximum receiving response delay can be configured as 2000ms and the average current is about 30uA. Module can communicate with other modules which work in different channels and addresses, it is easy for networking and repeater. For example: module A transmits AA BB CC to module B (address: 0x00 01, channel: 0x80), HEX format is 00 01 80 AA BB CC (00 01 refers to the address of module B, 80 refers to the channel of module B), then module B receives AA BB CC (only module B). Broadcast transmission Set the module address as 0xFFFF, then the module can communicate with other modules in same channel. FEC Forward Error Correction, high coding efficiency & good correction performance. In the case of sudden interference, it can correct the interfered data packets proactively, so that the reliability & transmission range are improved correspondingly. Without FEC, those data packets can only be dropped. Sleep mode When the module works in sleep mode (mode 3), transmitting & receiving is not available, while the configuration is available. The typical current is 5.0uA in this mode. Application With better capability of penetration and diffraction than 2.4G, E30(915T20S) is suitable for the open environment with few obstacles. 1 2 3 4 5 6 1.2 Electrical Parameters No. Parameter item Parameter details Description 1 2 3 4 5 6 Size Weight 17 * 30mm
-
2.3g Average weight Frequency Band 907~922.5MHz Default: 915MHz, channel:16 Process Connector Lead-free, SMT To ensure the consistency and reliability 11PIN-2.0mm SMD Supply voltage 2.1 ~ 5.5V DC Note: the voltage higher than 5.5V is forbidden Page 2 of 8 Technical Support : support@cdebyte.com E30(915T20S)-User Manual-V1.0 Website www.cdebyte.com/en 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Communication level Operation Range Transmitting power Air data rate Standby current Maximum 5.2V 2000m 20dBm 1kbps 5.0uA Transmitting current 89mA@20dBm Receiving current Communication interface Driving mode 16mA UART UART The difference with supply voltage should be less than 0.3V to reduce power consumption Clear and open area, 20dBm, antenna gain: 2dBi height: 2mair data rate: 1kbps Four optional level: 20, 17, 14, 10dBm Eight optional level: 1, 2, 5, 8, 10, 15, 20, 25kbps M1=1, M0=1 ( Mode 3 ) The proposed power supply current is not less than 200mA Mode 0 or 1 8N1, 8E1, 8O1eight kinds of UART baud rate, from 1200 to 115200 bpsDefault: 9600 Can be configured to push-pull/high pull, open-drain Transmitting length 512 bytes buffer 58 bytes per package Receiving length 512 bytes buffer 58 bytes per package 65536 Easy for network, broadcast and fixed transmission Address WOR Available Antenna type Stamp hole Minimum average power consumption is about 30uA (applicable for battery powered applications) IPX+stamp hole+spring antenna to lead out, 50 characteristic impedance Operating temperature
-40 ~ +85
-
Operating humidity 10% ~ 90%
Relative humidity, no condensation Storage temperature
-40 ~ +125
-
Sensitivity
-138dBm@0.3kbps Sensitivity has nothing to do with baud rate or timing Page 3 of 8 Technical Support : support@cdebyte.com E30(915T20S)-User Manual-V1.0 Website www.cdebyte.com/en 2. UART functional description (default) 2.1 Fixed transmission Hex Description The format: Hexadecimal, such as00 03 04 AA BB CC 00 03 is the address of receiving module04 is the channel AA BB CC is the transmission data Transmitting module A Hexadecimal Address00 01Channel 02 Receiving module B Hexadecimal Address00 03Channel 04 Hexadecimal Address00 05Channel 04 Hexadecimal Address00 07Channel 06 Receiving module C Receiving module D Module A must be in fixed mode. Module A Transmitting data Module B receiving data Module C receiving data Module D receiving data Only the modules with matched address and channel can receive the data. In fixed transmission, modules only support 1 packet length (pls refer to electrical parameters). If the data packets exceed, then it need to be subcontracted automatically. Hexadecimal Hexadecimal AA BB CC Hexadecimal No Hexadecimal No 00 03 04 AA BB CC 2.2 Broadcast transmission Hex Description Hexadecimal Address00 01Channel : 02 Hexadecimal Address00 03Channel 04 Hexadecimal Address00 05Channel 04 Hexadecimal Address00 07Channel 06 The format: Hexadecimal, such asFF FF 04 AA BB CC FF FF is the address04 is the channel of receiving moduleAA BB CC is the transmission data Transmitting module A Receiving module B Receiving module C Receiving module D Module A must be in fixed mode. Module A Transmitting data Module B receiving data Module C receiving data Module D receiving data All the module with this channel can receive the data. In fixed transmission, modules only support 1 packet length (pls refer to electrical parameters). If the data packets exceed, then it need to be subcontracted automatically. Hexadecimal Hexadecimal AA BB CC Hexadecimal AA BB CC Hexadecimal No FF FF 04 AA BB CC 2.3 Broadcast address 1. For example, set the address of module A as 0xFF FF, and the channel as 0x04. 2. When module A works as the transmitter (transparent transmission), all the receiving module with the channel 0x04 can receive the data, so as to realize the broadcast. 2.4 Monitoring address 1. For example, set the address of module A as 0xFF FF, and the channel as 0x04. 2.When module A works as the receiver, all the receiving module with the channel 0x04 can receive the Page 4 of 8 Technical Support : support@cdebyte.com E30(915T20S)-User Manual-V1.0 Website www.cdebyte.com/en data, so as to realize the monitoring. 3. Functional description 3.1 Pin definition Pin No. Pin item Pin direction Pin application 1 2 3 4 5 6 7 8 9 10 11 M0 M1 Input Work with M1 & decide the four operating modes. weak pull-up Floating is not allowed, can be ground. Input Work with M0 & decide the four operating modes. weak pull-up Floating is not allowed, can be ground. RXD Input output pin. Can be configured as open-drain or pull-up TTL UART inputs, connects to external (MCU, PC) TXD input. TXD Output input pin. Can be configured as open-drain or push-pull TTL UART outputs, connects to external RXD (MCU, PC) output To indicate module s working status & wakes up the external MCU. During the procedure of self-check AUX Output initialization, the pin outputs low level. Can be configured as open-drain output or push-pull output (floating is VCC GND ANT GND GND GND allowed). Power supply 2.1V~5.5V DC Ground Antenna Ground Ground Ground Page 5 of 8 Technical Support : support@cdebyte.com E30(915T20S)-User Manual-V1.0 Website www.cdebyte.com/en 3.2 Connect to MCU No. 1 2 The UART module is TTL level. Description ( STM8L MCU ) For some MCU works at 5VDC, it may need to add 4-10K pull-up resistor for the TXD & AUX pin. 3.3 Reset No. 1 Description When the module is powered, AUX outputs low level immediately, conducts hardware self-check and sets the operating mode on the basis of the user parameters. During the process, the AUX keeps low level. After the process completed, the AUX outputs high level and starts to work as per the operating mode combined by M1 and M0. Therefore, the user needs to wait the AUX rising edge as the starting point of modules normal work. 3.4 AUX description AUX Pin can be used as indication for wireless send & receive buffer and self-check. It can indicate whether there are data that are yet to send via wireless way, or whether all wireless data has been sent through UART, or whether the module is still in the process of self-check initialization. Indication of UART outputcan be used to wake up external MCU. Description No. 1 Page 6 of 8 Technical Support : support@cdebyte.com E30(915T20S)-User Manual-V1.0 Website www.cdebyte.com/en Indication of wireless transmitting Buffer (empty): the internal 512 bytes data in the buffer are written to the RFIC (Auto subpackage). When AUX=1, the user can input data less than 512 bytes continuously without overflow. Buffer (not empty): when AUX=0, the internal 512 bytes data in the buffer have not been written to the RFIC completely. If the user starts to transmit data at this circumstance, it may cause overtime when the module is waiting for the user data, or transmitting wireless subpackage. Notes: When AUX = 1, transmitted already, it does not mean that all the UART data of the module have been perhaps transmission. packet data last still the of in is 2 3 No. 1 2 3 4 Configuration procedure of module Only happened when power-on resetting or exiting sleep mode. Notes for AUX For function 1 & function 2 mentioned above, the priority should be given to the one with low level output, which means if it meets each of any low level output condition, AUX outputs low level, if none of the low level condition is met, AUX outputs high level. When AUX outputs low level, it means the module is busy & cannot conduct operating mode checking. Within 1ms since AUX outputs high level, the mode switch will be completed. After switching to new operating mode, it wont be work in the new mode immediately until AUX rising edge 2ms later. If AUX is on the high level, the operating mode switch can be effected immediately. When the user switches to other operating modes from mode 3 (sleep mode) or its still in reset process, the module will reset user parameters, during which AUX outputs low level. Page 7 of 8 Technical Support : support@cdebyte.com E30(915T20S)-User Manual-V1.0 Website www.cdebyte.com/en 4. Customization Please contact us for customization. Ebyte has established profound cooperation with various well-known enterprises. 5. About us Chengdu Ebyte Electronic Technology Co., Ltd. (Ebyte) is specialized in wireless solutions and products. We research and develop various products with diversified firmware;
Our catalogue covers WiFi, Bluetooth, Zigbee, PKE, wireless data transceivers & etc.;
With about one hundred staffs, we have won tens of thousands customers and sold millions of products;
Our products are being applied in over 30 countries and regions globally;
We have obtained ISO9001 QMS and ISO14001 EMS certifications;
We have obtained various of patents and software copyrights, and have acquired FCC, CE, RoHs & etc. Page 8 of 8 Technical Support : support@cdebyte.com FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The modular can be installed or integrated in mobile or fix devices only. This modular cannot be installed in any portable device . FCC Radiation Exposure Statement This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This modular must be installed and operated with a minimum distance of 20 cm between the radiator and user body. If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: 2ALPH-E30 Or Contains FCC ID: 2ALPH-E30 When the module is installed inside another device, the user manual of the host must contain below warning statements;
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product.