all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
15 UserMan r1 | Users Manual | 1.81 MiB | ||||
1 | ID Label/Location Info | |||||||
1 | External Photos | |||||||
1 | Internal Photos | |||||||
1 | Test Setup Photos | |||||||
1 | Test Report | |||||||
1 | Operational Description | |||||||
1 | RF Exposure Info |
1 | 15 UserMan r1 | Users Manual | 1.81 MiB |
Piglet Aerial Photography / Real-time FPV / WiFi Control Heading Hold Mode / Low Battery Alarm Out of Range Alarm / One Button Take Off/Landing High/Low Speed Mode / Custom Route Mode Altitude Hold Mode U36W User Manual Catalog Important Statement Safety Precautions Safe Notice for Drone Battery Charging Instruction for Drone Battery Check List Before Flight Instruction for Drone and Transmitter Pre-flight Operation Instruction Functions Introduction Spare Parts Installation Instruction To know your APP Spare Parts Troubleshooting Guide www.udirc.com 3 3 6 6 7 8 13 19 24 25 35 37 2 www.udirc.com Important Statement Thank you for buying UDIRC's product. People who under 14 years old must not use the product. Please read this brochure carefully before using the product. You are regarded as accepting all content in this user manual when using this drone. This product is not an ordinary toy but a piece of complicated equipment which is integrated with professional knowledge by mechanic, electronic, air mechanics, high-frequency emission etc. The users promise to be responsible for their behavior when using this product and relevant APP. The users promise to use the drone and relevant APP for legal purpose, and agree to obey above rules and local laws and regulations. We undertake no liability for those accidents caused by environment, illegal behavior, improper operation and refitting of the drone after sale of the product. We have entrusted the distributor to provide technology support and after-sale service. If you have any questions about use, operation, repair etc., please contact the local distributor.
* Keep the packing and user manual so as to refer to the important information whenever. Safety Precautions This drone is suitable for experienced RC drone user aged 14 years or above. This product contains small parts, please put it out of childs reach. 3 www.udirc.com
(1) Flying Area The flying field must be legally approved by your local government. Do not fly the drone near in the airport. Keep far away from the airport more than 5km when flying a RC drone. Flying field must spacious enough and we suggest at least 8M (length)*8M (width)*5M (height).
(2) Use correctly For safety elements, please only use UDIRCs spare parts to replace the damaged parts. Improper assembly, broken main frame, defective electronic equipment or unskilled operation all may cause unpredictable accidents such as drone damage or human injury. Please pay special attention to safety operation and have good knowledge of accident responsibility that the user may cause.
(3) Keep away from obstacles and crowd The speed and status of a flying RC drone is uncertain and it may cause potential danger. So the user must keep away from crowd, tall building, power lines etc. when operating a flying RC drone. Do not fly a RC drone in rainy, storm, thunder and lighting weather for the safety of user, around people and their property.
(4) Keep away from humid environment The drone inside is consisted of precise electronic components. Humidity or water vapor may damage electronic components and cause accident. 4 www.udirc.com
(5) Safe operation Please operate the RC drone in accordance with your physical status and flying skill. Fatigue, listlessness and improper operation may increase the rate of accident.
(6) Keep away from rotating parts Rotating parts like propellers or motors may cause serious injury and damage. Keep face and body away from rotating parts.
(7) Keep away from heat The RC drone is made of metal, fiber, plastic, electronic components etc. Keep away from heat and sunshine to avoid distortion and damage.
(8) The drone should be controlled within max control distance. Do not fly the drone near tall building, high voltage cable or other place with signal interference. Or may cause signal interruption and the drone will out of control, which may result of accident.
(9) Do not touch the hot motor to avoid being burnt.
(10) Please use the recommended charger only. Power off the drone before cleaning the RC drone. Check the USB cable, charging plug etc. regularly to ensure they can work well. If there is any damage, stop using it immediately till its fixed well. 5 www.udirc.com Safe Notice for Drone Battery
* Do not put the battery on high temperature place, such as fire or heating device to avoid damage or explode.
* Do not use the battery to crash or hit hard surface.
* Do not put the battery in water and keep it in dry place.
* Do not open the battery.
* Do not leave the battery without supervision when charging.
* Make sure that there is no short circuit of the power wire.
* Please use the recommended charger only.
* Check the chargers wire, plug, surface regularly. Do not use any broken charger.
* If do not fly the drone more than one week, maintain the drone battery with about 50% power to keep its performance and working life. Charging Instruction for Drone Battery 1. Connect the drone battery with USB cable first and then choose one of the method as below picture shown to connect with USB plug. 2. The red USB indicator light keeps bright when charging and the light turns green when fully charged( The switch must be powered off when charging).
* For faster charging, it is recommended to use an adapter with 5V 2A output current (not included) to charge the battery 6 www.udirc.com Phone Charger Power Bank Computer Charging Car Charger Li-Po Battery Disposal & Recycling Wasted Lithium-Polymer batteries must not be placed with household trash. Please contact local environmental or waste agency or the supplier of your model or your nearest Li-Po battery recycling center. Check List Before Flight 1. Make sure the drone battery and transmitter battery are fully charged. 2. Make sure the Left Stick of the transmitter in the middle position. 3. Please strictly obey the order of turn on and turn off before operation. Turn on the transmitter power first and then turn on the drone power before flying; turn off the drone power first and then turn off the transmitter power when finish flying. Improper turn on and turn off order may cause the drone out of control and threaten peoples safety. Please cultivate a correct habit of turn on and turn off. 4. Make sure the connection is solid between battery and motor etc. The ongoing vibration may cause bad connection of power terminal and make the drone out of control. 7 www.udirc.com 5. Improper operation may cause drone crash, which may arouse motor defective and noise, and then effect the flying status or even stop flying. Please go to the local distributor to buy new parts for replacement so that the drone will return to its best status. Instruction for Drone and Transmitter Drone Propeller Guard Drone Cover Housing Front Camera Propeller Guard Left Right Propeller Guard Propeller Guard Switch Rear 8 www.udirc.com Front LED (Green) B Propeller Drone Bottom Housing A Propeller A Propeller B Propeller Rear LED (Red) Specification Drone Size 66x66x37mm Charging Time for Drone Battery 25~30 mins Drone Weight 23g Max Flying Distance/Radius 10~15 m Propeller Diameter 32mm Camera Resolution Flying Time 5~7 mins Drone Battery 3.7Vx180mAh Frequency Main Motor 640*480 2.4Ghz 0614*4 9 Exploded View www.udirc.com 1 2 3 2 4 5 6 7 8 9 No. 1 2 3 4 5 6 7 10 11 12 2 13 6 2 7 4 5 Name Drone Cover Housing Propeller Guards Camera PCB Clockwise Motor (Red and Blue Wire) B Propeller (Counterclockwise) Counterclockwise Motor (Black and White Wire) A Propeller (Clockwise) 10 No. 8 9 10 11 12 13 Name Camera Lens Camera Head Cover Lipo Battery Switch Board Receiver Board Drone Bottom Housing Transmitter UA20UA20UA20 Left Stick
(Throttle / Rudder) Take Off /
Landing /
Emergency Stop Button www.udirc.com Heading Hold Mode High / Medium /
Low Speed Mode Right Stick
(Forward /
Backward / Left /
Right) Power Switch Power Indicator Light Trimmer mode button ( Press Down) 11 www.udirc.com Brief Introduction for Button Functions Left Stick Right Stick Move the Stick to forward / backward / left / right to fly the drone to up / down / turn left / turn right. Move the Stick to forward / backward / left / right to fly the drone to forward / backward / left / right. Power Switch Push up the power switch to turn on the transmitter, and pull down to turn off. Heading Hold Mode High / Medium/Low Speed Mode Take Off / Landing /
Emergency Stop Button Press the button to enter heading hold mode, and press again to exit from heading hold mode. Press down the Left Stick to switch to High /Medium/ Low Speed Press the button and the drone will fly up automatically. Press the button again and the drone will land on the ground automatically. Press and hold the button more than 1s, the drone propellers will stop and fall down immediately. Trimmer mode Button Press down this button,move the right stick to the required trimmer direction, then it will adjust the direction accordingly, when loose the stick, then ESC from the trimmer mode. Battery installation:
Open the battery cover on the back side of the transmitter and put 3 alkaline batteries (AAA, not included) into the box in accordance with electrode instructions, as picture shown. Battery Cover 3X1.5V Alkaline Batteries 12 www.udirc.com Notice:
1. Make sure the electrodes are correct. 2. Do not mix new with old batteries. 3. Do not mix different kinds of batteries. 4. Do not charge the non rechargeable battery. Pre-flight Operation Instruction Frequency Pairing 1. Turn on the transmitter switch (Picture 1) and the power indicator light flashes rapidly. Push the Left Stick all the way down to the lowest position and then release. The Left Stick will back to the middle position automatically.
(Picture 2 / 3) The power indicator light flashes slowly, which indicates the transmitter is ready for frequency pairing. Picture 1 Picture 2 2. Power on the drone. (Picture 4 3. Put the drone on the flat surface, the drone body lights turn from flashing to solid bright, which indicates successful frequency pairing. Picture 3 Picture 4 13 www.udirc.com Important Notice: Please make sure the drone is placed on the horizontal position after powering on the drone, so that the drone can work well. Checklist before Flight 1. The camera is in front of the drone. Keep the drone front away from you. 2. Power on the drone and check the direction of the rotating propellers. The left front and right rear A propellers rotating clockwise while the right front and left rear B propellers rotating counterclockwise. 3. Move the Left Stick and Right Stick at the same time as Picture 5 shown(45 degree inward) to start the motors and repeat previous step again to lock the motors. Picture 5 4. After starting the motors, push up the left stick to fly up the drone slowly, and then pull down the left stick to the lowest position slowly, then the drone lands on the ground. 5. Its recommended to repeat above Steps 4 to practice. 6. Adjust relative transmitter Trimmer button to adjust the rudder if the drone tilts to one side when flying. 14 www.udirc.com Calibration Instruction Please follow below steps to calibrate the drone if the drone becomes imbalance after crashing during the flight, and can not be adjusted by trimmer button and cause difficult operation. 1. Power off the drone, then turn off the transmitter switch. 2. Turn on the transmitter switch, push the Left Stick all the way down to the lowest position (Picture 6) and then release. The Left Stick will back to the middle position automatically (Picture 7). The transmitter is ready for frequency pairing mode. Picture 7 Picture 6 3. Power on the drone and put it on a flat surface in a horizontal position. The drone body lights change from flashing to solid bright, which indicates successful frequency pairing. 4. Do not move the Left Stick before successful calibration. Push the Right Stick as Picture 8 shown and then release. The drone body lights flash, which indicates that the drone is calibrating. When the drone body lights become solid, which indicates successful calibration. Picture 8 Notice: When the drone is fiercely impacted or crashed, it may cause the gyro can not recover and cause difficult control, if so, then you need to power off and power on again to calibrate. 15 www.udirc.com Flying Control Notice: Every time before the drone take off, move the Left Stick and Right Stick at the same time as Picture 5 shown(45 degree inward) to start the motors. Push up the Left Stick slowly to fly up the drone or press down the one button take off . Push up the stick,then the drone flies up Pull down the stick, then the drone goes down Left Stick Move the stick to the left, then the drone turns to left Move the stick to the right, then the drone turns to right 16 www.udirc.com Push up the stick, then the drone flies forward Right Stick Pull down the stick, then the drone goes backward Move the stick to the left, then the drone turns to left Move the stick to the right then the drone turns to right 17 www.udirc.com Forward and backward trimmer When take off, if the drone tilts forward, press down the left stick in the center, and push the right stick backwards. Otherwise push forwards. Left and right turning trimmer When take off, if the drone head rotates to left,then press down the left stick in the center and push left stick to right. Otherwise push to left. Left and right side flying trimmer When take off, if the drone tilts to left, then press down the left stick in the center and push the right stick to right side. Otherwise push to left. 18 www.udirc.com Functions Introduction Two Take Off Methods 1. Method 1 (Take off) : After frequency pairing successful, then move the Left Stick and Right Stick at the same time as Picture 5 shown(45 degree inward) to start the motors. Push up the Left Stick to fly up the drone to certain altitude and then release the stick. 2. Method 2 (One Button Take Off): Press the Take Off /
Landing / Emergency Stop Button (Picture 9) , the drone will fly up automatically and keep flying at an altitude of 1.2 meters approximately. Picture 9 Take Off / Landing / Emergency Stop Button Landing Methods 1. Method 1 (Landing): Push the Left Stick all the way down to the lowest position(Picture 2/6) and hold it till the motors stop and the drone will land on the ground. 2. Method 2 (One Button Landing): Press the Take Off /
Landing / Emergency Stop Button once shortly(picture 9), and the drone will land on the ground automatically.
(When using this function, you can not touch the left stick, if not, then the function will fail) 19 www.udirc.com Emergency Stop: When the drone in emergency situation and going to hit the walking people or obstacle etc., press the Take Off / Landing / Emergency Stop Button immediately and hold it for more than 1s. The propellers will stop immediately. Tip: Do not use the emergency stop function unless in emergency situation. The drone will fall down suddenly after all propellers stop. Altitude Hold Mode Altitude hold mode indicates that the drone maintains a consistent altitude while allowing roll, pitch, and yaw to be controlled normally. It makes easier to control the drone for beginner and more stable for aerial photography. Push the Left Stick up (down) to fly the drone up (down) at certain altitude and then release the Stick. The Stick will back to the center position (Altitude Hold Center) as Picture 10 shown. And the drone will keep flying at current altitude. Repeat above steps if you want to change the drone altitude
(Default mode). Picture 10 Altitude Hold Center 20 www.udirc.com High / Medium/Low Speed Mode Switch Low Speed Mode(Mode 1) 1. Low Speed Mode is suitable for beginner. Medium speed Mode(Mode 2) 2. Medium Speed Mode is suitable for skillful pilots to play in the gentle breeze. High Speed Mode(Mode 3) 3. High Speed Mode is suitable for expert to experience aerial stunt in outdoor. High / Medium/Low Speed Mode Switch Heading Hold Mode
* Drones generally have a front and rear indicated by LED lights or colored propellers. By default, the users are required to tell the front and the rear of the drone when flying. Under heading hold mode, the users can operate the drone without worrying about the orientation (left is left and right is right all the time, regardless of where your drone is pointing at). 21 www.udirc.com Heading Hold Mode is designed for beginners and users who fly the drone in daylight or at a far distance. When the drone in heading hold mode, push the Right Stick to forward / backward / left / right, and the drone will fly to forward / backward / left / right accordingly. Prerequisite: Position the drone in such a way that its front is your front (see Picture 1). Tip: Do not change the orientation of the transmitter (see Picture 2) after entering heading hold mode. Front (Camera) Front (Camera) Left Right Left Right Rear (Power Switch) Rear (Power Switch) Picture 2 Picture 1 To turn on Heading Hold Mode, press Heading Hold Mode button and the drone LED lights flash, which indicates the drone enters heading hold mode. To turn off Heading Hold Mode, press Heading Hold Mode button again and the drone LED lights turn solid, which indicates the heading hold mode is off. Heading Hold Mode Button 22 www.udirc.com Low Battery Alarm When the transmitter in low battery, the transmitter will beep Di-di-di... to remind the user to land the drone to replace the batteries as soon as possible. Or the drone may be out of control. When the drone in low battery, the transmitter will beep Di.di.di... constantly to remind the user to land the drone as soon as possible. The flip function will turn off automatically when the drone in low battery. Out of Range Alarm When the drone is going to fly out of the max remote control distance, the transmitter will beep Didi..didi..didi... to alarm the user to fly back the drone immediately. Or the drone may be out of control and fly away. 23 www.udirc.com Spare Parts Installation Instruction Propeller Installation and disassembly Diagram When disassemble, pull up the propeller in the vertical direction (Picture 11) and remove as Picture 12. Notice: Because the propeller is blowing up structure, it should keep a bit gap between the motor housing and the propeller( Picture 13). Picture 11 Picture 12 About 0.5mm Picture 13 24 www.udirc.com Propellers guards installation and disassembly diagram When disassemble, remove one side of the guard from the buckle, and then pull out ( Picture 14). When install, aim the groove of the motor housing buckle and then press down (Picture 15). Picture 14 Picture 15 To know your APP Download and Install the APP: Flyingsee The APP is suitable for mobile phone with iOS and Android system, please download from the mobile phone software store:
1. For mobile phone with iOS system, please search Flyingsee in APP Store. 2. For mobile phone with Android system, please search Flyingsee in Google Play. 25 www.udirc.com 3. Scan the QR code on the right or the QR code in the box to download Flyingsee. Frequency Pairing between Mobile Phone and Drone WiFi:
1. Power on the drone. Put the drone on the flat surface in horizontal position. 2. Enter set up of the mobile phone, turn on WiFi (WLAN) and choose udirc-***, return to desktop after successful connection. 3. Click on the icon Flyingsee and click on to enter remote control interface to experience real time transmission. 26 www.udirc.com EMERGENCY HOME Explore UDIRC Drone Learn the operation of drone Remote control interface Flyingsee Help Media 100%
Click on the icon Home Page Real time Transmission Interface 4. Click on to enter Virtual Control Interface. At this time the drone LED lights change from flash to solid bright, which indicates successful frequency pairing and the drone is ready to be controlled via APP. EMERGENCY 00:00 Virtual Control Interface Important Tip: Ensure the drone is put it on a flat surface in horizontal position so that the drone can work well. Or it may be failed to control. 27 Introduction for APP Icons Home Page Icons Explore UDIRC Drone Learn the operation of Drone Remote control interface www.udirc.com Help Media Remote Control Interface Home Page Icon Click on the icon and back to home page. Virtual Reality Mode Click on the icon to enter virtual reality mode to experience first person view (only available when using with a VR headset). Click on the icon again to exit from virtual reality mode.
28 www.udirc.com Flight Route Setting Mode Click on this icon and it turns red. Draw a flight route in the right area. The drone will fly according to the flight route. Click on the icon again to exit from Flight Route Setting Mode. The icon turns white. EMERGENCY Emergency Stop The icon is red by default. Click this icon and the propellers will stop immediately. The drone will fall down to the ground straightly. Tip: Do not use the emergency stop function unless in emergency situation. Remote Control Signal To show the drones WiFi signal strength. Setting Click on this icon to set some parameters, and click again to exit. SETTING Trimming Save Reset Transmission quality 480P Click on Save to save trimming setting. Choose Reset for factory reset. 29 www.udirc.com Remote Control Virtual Control Stick The virtual control stick is hidden by default. Click on the icon to turn on the virtual control stick. Gravity Induction Mode Click on this icon to enter gravity induction control mode. (only available for flying left / right and forward /
backward). Click on the icon again to exit from gravity induction control mode. If the mobile phone shakes to the left / right, the Right Ball will move accordingly causing the drone to fly left / right. If the mobile phone shakes to forward / backward, the Right Ball will roll forward / backward, causing the drone to fly forward / backward. 30 www.udirc.com Video Click on this icon to record video. The recording time will show at the bottom of the screen. Click on this icon again to finish recording. Photo Click on this icon to take photo. Heading Hold Mode Click on this icon and it turns red, which indicates that the drone enter Heading Hold Mode. Click again to exit from Heading Hold Mode. The icon turns white. Media Click on this icon to view or delete the aerial video and photo. Click on the arrow to exit. High / Low Speed Mode By default, the drone is in Low Speed Mode L. Click on H to enter High Speed Mode. One Button Take Off Click on this icon and it turns red shortly. The drone will fly up automatically and stay flying at an altitude of 1.2 meters. 31 www.udirc.com One Button Landing Click on this icon and the icon turns red, the drone will fly down slowly and land on the ground. All propellers also will stop. The video and the photos are stored in the local phone gallery, you can display it in the phone directly, or you also can display it in the APP via quick icon to enter Media interface. Notice: App must be authorized to access the phone gallery, if not, then may be unavailable to display the video and photos. APP Calibration Instruction If the drone becomes difficult to operate and hover, you need to calibrate again. 1. Please refer to the Frequency Pairing between Mobile Phone and Drone WiFi. 2. Do not push the Left Ball before successful calibration. Move the Right Ball as the picture shown on the right. The drone body front light flashing, which indicates that the drone is calibrating. When the drone body front light gets solid, which indicates successful calibration and the drone is ready to be controlled. 32 APP Flying Control Take off EMERGENCY 00:00 www.udirc.com Click on this icon and it turns red shortly. The drone will fly up automatically and stay flying at an altitude of 1.2 meters. To fly up or down:
Move the Left Ball up to fly the drone up and move the Left Ball down to fly the drone back down. Left Ball To fly right or left:
Move the Right Ball to the left to fly the drone to the left, and move the Right Ball to the right to fly the drone to the right. Right Ball To rotate left or right:
Move the Left Ball to the left to rotate the drone to the left. Move the Left Ball to the right to rotate the drone to the right. To fly forward or backward:
Move the Right Ball up to fly the drone forward, and move the Right Ball down to fly the drone backwards. 33 www.udirc.com If the drone tilts forward or backward Click the - of the Forward / Backward Trimmer to adjust the drone till balance if the drone tilts forward. Click the + to adjust the drone till balance if the drone tilts backward. If the drone rotates to left or right Click the + of the Rotation Trimmer till balance if the drone rotates left. Click the
- to adjust the drone till balance if the drone rotates right. If the drone tilts to the left or right Click the + of the Left / Right Trimmer till balance if the drone tilts to the left. Click the - to adjust the drone till balance if the drone tilts to the right. Notice:
1. If you can not find the WiFi signal to connect, turn off WiFi and turn on again to search and connect. 2. The available WiFi control radius/distance is 10m, please control the drone within this range. 3. When alternating control from mobile phone to transmitter, the transmitter left stick must be in the center position, or exit from the APP. If not then you can not control the drone alternately. 34 www.udirc.com Spare Parts For convenience, the spare parts are listed for you to choose, which can be purchased from the local seller. U36W-01 Drone Cover Housing U36W-02 Drone Bottom Housing U36W-03 A Propeller U36W-04 B Propeller U36W-05 Propeller Guards U36W-06 Camera Head Housing U36W-07 U36W-08 Clockwise Motor
( Red and blue wire) Counter-clockwise Motor
( Black and white wire) U36W-09 Drone Lipo Battery 35 www.udirc.com U36W-10 Camera Board U36W-11 Receiving Board U36W-12 USB Cable U36W-13 Transmitter Important Notice Our company's products are improving all the time, design and specifications are subject to change without notice. All the information in this manual has been carefully checked to ensure accuracy, if any printing errors, our company reserve the final interpretation right. 36 www.udirc.com e d i u G g n i t o o h s e l b u o r T
. y r e t t a b r e t t i m s n a r t e h t e c a p e R l
. 1
. y r e t t a b w o L
. 1 n o i t u l o S e s u a C m e l b o r P m e l b o r P
. o N h t i w e c n a d r o c c a n i y r e t t a b e h t l l a t s n I
. 2
. l a u n a m r e s u e h t d n a y r e t t a b e h t n e e w t e b t r i d e h t n a e l C
. 3
. e c i l s y r e t t a b e h t
. r e d r o e s r e v e r n i e r a e l o p e v i t a g e n d n a e l o p e v i t i s o p y r e t t a b e h T
. 2
. t c a t n o C r o o P
. 3
. 3
. 2
. 1 e v o b a s a e m a s e h T
. 1
. f f o s i t h g i l r o t a c i d n I
. 1 e h t n o r e w o p d n a e n o r d e h t t r a t s e R
. 2
. r e t t i m s n a r t n i p e t s y b p e t s e n o r d e h t e t a r e p O
. 3
. l a u n a m r e s u e h t h t i w e c n a d r o c c a r e l l e s l a c o l
. s t r a p d e g a m a d e c a p e r d n a m o r f s t r a p e r a p s y u b o T
. 4 l d e g a m a d s i t n e n o p m o c c i n o r t c e l e e h T
. 4
. h s a r c t n e u q e r f r o f
. n o i t a r e p o s i M
. 3
. y b r a e n l a n g i s g n i r e f r e t n i s i e r e h T
. 2 r e t t i m s n a r t f f o s i t h g r o t a c i d n i l i e h T r i a p o t l i a F e n o r d e h t h t i w r e t t i m s n a r t e c n a d r o c c a n i r e l l e p o r p e h t l l a t s n I
. 3
. l a u n a m r e s u e h t h t i w
. r e l l e p o r p f o n o i t a l l a t s n i t c e r r o c n I
. 3
. y r e t t a b e n o r d e h t e g r a h c e R
. 2
. y r e t t a b w o L
. 2
. r e l l e p o r p e h t e c a p e R l
. 1
. y l s u o i r e s d e m r o f e d r e l l e p o r p e h T
. 1 r o d e r e w o p
. y l f t o n n a c e n o r d e h T
-
r e d n u s i 1 2 3 37 r o f d n u o r g t a l f e h t n o e n o r d e h t t u P o t e n o r d e h t e h t t r a t s e r r o s 0 1 t u o b a
. 3 i
. n a g a e t a r b i l a c
. r e d l o h r o t o m e h t e c a p e R l
. 2
. y r e t t a b e n o r d e h t e g r a h c e R
. 1
. r o t o m e c a p e R l
. 4 o t r e l l e s l a c o l m o r f y r e t t a b w e n a y u B
. 2
. y r e t t a b e h t e c a p e r l n e h t d n a y r e t t a b e h t t c e n n o c s i D
. 3 i
. n a g a g u p e h t h t i l w t i t c e n n o c t n e l o i v r e t f a t e s e r t o n d d o r y g e h T
. 3 i
. h s a r c
. d e m r o f e d r e d l o h r o t o m e h T
. 2 r e v o r o d e r i p x e s i y r e t t a b e h T
. 2
. n o i t c e t o r p e g r a h c s i d
. d e g a m a d s i r o t o m e h T
. 4
. y r e t t a b w o L
. 1
. t c a t n o c r o o P
. 3
. r e l l e p o r p e c a p e R l
. 1
. y l s u o i r e s d e m r o f e d r e l l e p o r p e h T
. 1 www.udirc.com
. l l e w t c e n n o c d n a e r i w e h t k c e h C
. 1 a r e m a c f o e r i w e h t t c e n n o c t o n d D i
. 1
. t c a t n o c r o o p r o x o b
. t c e n n o c
-
e r d n a e r i w e h t f f o t u C
. 2
. y b r a e n l a n g i s g n i r e f r e t n i s i e r e h T
. 2 l a c o l m o r f x o b a r e m a c w e n a y u B
. 3 l
. e c a p e r o t r e l l e s e n o h p l l e c e h t d a e r d n a e c i t c a r P
. 1
. y l l u f e r a c n o i t c u r t s n i g n i l l o r t n o c
. h g u o n e d e c n e i r e p x e t o N
. 1
. a r e m a c d e g a m a D
. 3 e n o r d e h T t o n d u o c d n a r e v o h l
. e d i s e n o o t s t l i t e n o r d e h T r o t a c i d n i
. f f o s i t h g i l t o n d u o C l e h t e e s
. e r u t c i p y b l o r t n o c
. e n o h p l l e c o t d r a H 4 5 6 7 38 www.udirc.com FCC Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.These limits are designed to provide residential protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not Installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception. which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on the circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 39 www.udirc.com FCC WARNING:
The equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. Modifications not authorized by the manufacturer may void users authority to operate this device. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)this device may not cause harmful interference,and
(2)this device must accept any interference received, including interference that may cause undesired operation. MADE IN CHINA
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2017-04-25 | 2448 ~ 2472 | DXX - Part 15 Low Power Communication Device Transmitter | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2017-04-25
|
||||
1 | Applicant's complete, legal business name |
Chenghai Udirc Toys Co.,Ltd
|
||||
1 | FCC Registration Number (FRN) |
0020902250
|
||||
1 | Physical Address |
Dengfeng Industrial Zone,Chenghai District,Shantou
|
||||
1 |
Guangdong
|
|||||
1 |
China
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
j******@eurofins.com
|
||||
1 | TCB Scope |
A2: Low Power Transmitters (except Spread Spectrum) and radar detectors operating above 1 GHz
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
ZKW
|
||||
1 | Equipment Product Code |
UA201702002
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
Y**** W****
|
||||
1 | Telephone Number |
0754-********
|
||||
1 | Fax Number |
0754-********
|
||||
1 |
s******@udirc.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DXX - Part 15 Low Power Communication Device Transmitter | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | U36W Piglet (transmitter) | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Dongguan NTC Co.,Ltd.,
|
||||
1 | Name |
s****** s****
|
||||
1 | Telephone Number |
86-76********
|
||||
1 |
s******@21cn.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 2448.00000000 | 2472.00000000 | 0.0040000 | ppm |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC