ZigBee Module ZM11 Product Manual MechanicalDrawings ABSOLUTE MAXIMUM RATINGS VIN to GND ..-0.3~3.5 V Other Pin to GND-0.3~3.5V RECOMMENDED OPERATING CONDITIONS Vcc to GND ..3.3 V+- 5%
Operating temperature ......0 to 40C ELECTRICAL CHARACTERISTICS Power consumption when RF 100% TX 17dBm 150mA Power consumption when RF continuous RX 45mA Power consumption when Idle state 20mA RF SPECIFICATIONS Frequency Band ..ISM 2.4 GHz TF Tx power17 dBm max Antenna Efficiency. 68% (Typical) Antenna SPECIFICATIONS Pin Signals 1. Power Supply Pin and Common pin Pin#
2 4 1,3,5,9,23 21 22 7 Pin Name VCC RF VCC GND BM RST LED0 6 20 LED1 KEY 2. Function Select pin Pin Type Description PW PW PW AI DI DO DO DI 3.3V RF Power supply 3.3V Digital Power Supply Ground Battery Monitor Pin Module Reset Input LED0 pin (active 0,output current 4mA), controlled by module LED1 pin (active 0,output current 4mA) Push Button Input pin low-active Pin#
11 10 8 Pin Name Pin Type DO,PUS*
DO,PUS*
DO,PUS*
FSL0 FSL1 FSL2 Description Function Select 0 Function Select 1 Function Select 2
*FSL0~FSL2 is Digital out signal for module Internal control signal, Strap for FSL2~FSL0 when power on or Reset- pin Low-> High , Leave FSLx pin floating means FSLx =F Pull-up FSLx to VCC by 4.7k ohm means FSLx= U Pull-down FSLx to GND by 4.7k ohm means FSLx= D 3. Router Multi Function pin Table FS1 UUU FS2 UUF FS3 UFU FS4 UFF FS5 FUU FS6 FUF FS7 FFU FS8 UUD FS9 UDU FS10 FFF ADC PWM DI DO I2C UART Pin 14 4 4 PWM3 15 PWM2 2 1 1 I2C SDA I2C SCL 2 2 2 2 2 4 2 4 4 4 1 2 6 8 1 1 1 1 1 DI1 DI1 DI1 DI1 DI1 DI1 PWM0 DI0 DI0 DI0 DI0 DI0 DI0 ADC0 16 ADC3 UART DO1 DI3 DI3 UART DI3 DI3 UART RT RT RT 17 ADC2 UART DO0 DI2 DI2 UART DI2 DI2 UART CT CT CT 18 ADC1 UART ADC1 DO1 DO1 UART ADC1 DI5 UART TX TX TX 19 ADC0 UART ADC0 DO0 DO0 UART ADC0 DI4 UART 12 13 PWM1 PWM0 RX DI1 DI0 PWM1 PWM1 PWM0 PWM0 DO3 DO2 RX DI3 DI2 DI5 DI4 DI7 DI6 RX DO0 DI0 Note : Router mode is always non-sleep. FS0 (DUU) is reserved for manufacture End Device Multi Function pin Table ADC PWM DI DO I2C UART Pin#
14 15 16 FS6:LS FS6:DS FS7:LS FS7:DS FS8:LS FS8:DS FDF FDD DDF DDD DFF DFD 4 1 4 1 DI1 DI0 DI1 DI0 UART UART RT RT 2 6 DI1 DI0 DI3 2 6 DI1 DI0 DI3 8 DI1 DI0 DI3 8 DI1 DI0 DI3 17 UART UART DI2 DI2 DI2 DI2 CT CT 18 UART UART ADC1 ADC1 DI5 DI5 TX TX 19 UART UART ADC0 ADC0 DI4 DI4 RX DI3 RX DI3 12 DI5 DI5 DI7 DI7 DI2 13 DI6 Note : LS=Light Sleep mode, DS=Deep Sleep mode DI4 DI6 DI4 DI2 Typical application for Function set 2 Analog Input pin (BM,ADC) CHARACTERISTICS Input resistance, signal .. 200k ohm (Typ) ADC full scale range .0~1.15 V Digital output(DO,PWM,UART TX,UART RT,LED) DC CHARACTERISTICS Logic-0 output voltage . 0.5V(max) @ output load 4mA Logic-1 output voltage . 2.4V (min) @ output load 4mA Digital Input(DI,UART RX,UART CT, KEY ,Reset) DC CHARACTERISTICS Logic-0 input voltage(VIL max)..0.5V Logic-1 input voltage(VIH min)..2.5V Federal Communications Commission (FCC) Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the users authority to operate the equipment. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver. Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiver isconnected.
-Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation of the device. FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Note:
The end product shall has the words Contains Transmitter Module FCC ID: 2AOWSIWAZBZM11 Further instruction to OEM relating to Part 15B/RF exposure subject to be re-evaluating while the module is installed to the host shall be given