CWFB211-XXX Specification Revision 01 2012/09/12 Prepared By: Jeff Hsieh RevisionHistory Revision 01 Date 2012/09/12 Notes Initial Release Owner Jeff Hsieh 1.WirelessSpec. WLAN: 2X2 MIMO Wi-Fi Frequency Range
(MHz) 802.11b 2412 2462(DTS) 802.11g 2412 2462(DTS) 802.11n 802.11a 802.11n HT20 2412 2462(DTS) HT40 2422 2452(DTS) 5180 5240(NII) 5745 5825(DTS) HT20 5180 5240(NII) HT20 5745 5825(DTS) HT40 5190 5230(NII) HT40 5755 5795(DTS) Modulation type Transition Rate:
Modulation Technology DSSS DSSS, OFDM OFDM OFDM OFDM Channels 11 11 11 7 4 5 4 5 2 2 Peak Rated Power 19.52dBm 23.87dBm 23.77dBm 23.71dBm 9.19dBm 23.88dBm 8.65dBm 24.81dBm 10.93dBm 24.60dBm CCK, DQPSK, DBPSK for DSSS 64QAM. 16QAM, QPSK, BPSK for OFDM Upto 300Mbps Antenna Designation:
Manufacturer Model No. Connector Type Type Gain
(2.4GHz) Gain
(5GHz) Ant 1 Airwave Technologies INC. EDA-8709-25GR2-A4-RM Revise SMA, unique Dipole Ant 2 dBi 2 dBi Ant 2 ARISTRTLE RFA-25-C2S1-70-90 unique Dipole Ant 2 dBi 2 dBi corp. Tranwo technology Ant 3 Ant 3-1 Tranwo technology Ant 3-2 Tranwo technology Ant 3-3 Tranwo technology corp. corp. corp. UDM Group Ant 4 Technology Co., Ltd Ant 5 Unictron Technologies Corporation SD001-201003-A101 RFA-05-2-L14M3-B70-1 202-000442-00 202-000441-00 26-52-01800G H2P566WKBA0100 Revise SMA, unique Revise SMA, unique unique unique unique unique Dipole Ant Dipole Ant 2dBi 2dBi 2 dBi 2 dBi Patch Ant 0 dBi
-1 dBi Patch Ant PCB Ant
(Green) PCB Ant
(Blue) 0.5 dBi
-0.5 dBi 2.5 dBi 4 dBi 2.3 dBi 4dBi This antenna list table could be used for CWFB211-XXX.. The max gain of 2.4G: 2.5dBi. The max gain of 5G: 4dBi. Federal Communications Commission (FCC) Statement You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation of the device. FCC RF Radiation Exposure Statement:
This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter and this equipment should be installed and operated with minimum distance 20cm between the radiator & your body. When suing IEEE 802.11a wireless LAN, this product is restricted to indoor use, due to its operation in the 5.15 to 5.25GHz frequency range. The FCC requires this product to be used indoors for the frequency range of 5.15 to 5.25GHz to reduce the potential for harmful interference to co channel mobile satellite systems. The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove. This RF module in the users manual of the end product which integrates this module. The users manual for OEM Integrators must include the following information in a prominent location End Product Labeling:
The final end product must be labeled in a visible area with the following:
Contains FCC ID: O7N-CWFB211-XXX.