TROUBLE SHOOTING If the Baby Monitor system does not operate correctly please check the following:
Fault Cause Action
- Flat batteries - Fit new batteries
- Wrong battery polarity - Fit the battery again in the
* Aiea mciemind Cen onactadlinasd "gt: =
Power light dim or not lit on Baby's unit te ea ae ee Re rein dia eacennane! arn gen NR ene Bie on or jack plug not connected | the battery compartment
- Check correct fitting at mains No sound from - Flat batteries - Fit new batteries Parent's unit - Wrong battery polarity - Fit the battery again in the
- Channel switches not on the right position as shown inside same setting the battery compartment
- ACIDC adaptor not switched | - Check channel setting on on or jack plug not connected} Parent's & Baby's Unit
~ Check channel fitting of mains adaptor Sound level metre ~ Power has not switched on - Check adaptor, batteries and lights not working volume/on/off switch Weak reception - Parent's unit & Baby's unit - Move Parent's unit closer to are out of range Babys unit
- Weak batteries - Replace batteries
~ Metal Clad building Buzzing, interference | - Could be due to another - Change channels on both etc Baby Monitor or Parent's and Baby's units environmental interference Static and other - Interference possibly from - Switch off other appliances if noises home appliances possible
- Out of range - Move units closer to each other High pitched sound | - Units are too close to each - Move the units further apart
(electronic feedback) | other - Reduce volume
- Volume is too high Specifications and designs are based on the latest information available at the time of printing and subject to change without notice. Fcc This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- _ Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver. eee ee ee
= -_- PONNSCE TS SQUIPMONT MNO BN OUTST ON S CHCUN CHTEFSNT TOM INAl LO WINCH INS FECSIVEr 5S CONNECISG.
- Consult the dealer or an experienced radio/TV technician for help. INSTRUCTION MANUAL CHIT SHUN ENTERPRISES CO.,LTD. CHIT SHUN ENTERPRISES CO., LTD 4111 FISHER DRIVE 415 N. Sullivan, Suite C #263 RICHMOND, BC Veradale, WA 99037 CANADA V6X 384 United States E-MAIL: service@chitshun.com.hk Phone: (509) 832-2073 Baby's Unit LIST OF COMPONENTS TO * Dan TD Integrated antenna (Baby's unit) LED power indicator (Baby's unit) DC jack (Baby's unit) Built-in microphone Battery door (Baby's unit) Monitor power on/off switch Channel switch (Baby's unit) Inteqrated antenna (Pareant'c init) Parent's Unit DC jack (Parent's unit) Battery door (Parent's unit) Channel switch (Parent's unit)
. Speaker Volume / on/off switch Signal receive indicator Sound level metre Mainc adantor HOW TO INSTALL BATTERI Baby's Unit Remove the battery door (e) by a screw driver and insert 4 x 'AAA' (UMA) size batteries*. Close the battery door by a screw driver before operate. Parent's Unit Remove the battery door (k) by a screw driver and insert 4 x 'AAA' (UMA) size batteries*. Close the battery door by a screw driver before operate.
* (Alkaline battery is recommended) Follow the direction indicated on the battery compartment to install the batteries as shown inside the battery compartment. CAUTION: THE WAY TO HANDLE THE MONITOR The rounded loop type antenna is not using as the handle for carrying around. Diagram 1 shown the wrong way to "handle the unit vs diagram 2 shown the correct way to handle the unit, please make sure not to handle the antenna" when to carry it around. Fail to do this may be caused weak or no reception and reduce performance. Diagram 2 SET UP THE SYSTEM Pore ee eect See i. LED power indicator (Parent's unit) r DCplug INTRODUCTION The Baby Monitor system is the ideal nursery baby monitor for parent to use it to take care of their baby. Do not allow the product to be used in damp conditions or immersed in water. Do not place the product next to heat sources such as radiators and sunny window etc. Baby monitor does not contain any user serviceable parts. Do not dismantle. When the Baby Monitor is not in used for long periods of time, remove all batteries So eS
>T Baby's Unit The Baby's unit should be placed in a convenient place within 3 metres (10 feet) of baby. A flat surface is recommended to place the Baby's Unit. The Baby's unit can be used via the mains adaptor * +(DC 6V 100mA). This AC/DC adaptor is provided for maximize the use of monitor. To operate the Baby's unit via the mains adaptor * +(DC 6V 100mA), just plug the adaptor into a convenient wall power socket and make sure you switch the power on if the socket has a switch. Turn the Baby's unit ON by turning the monitor switch (f), the LED power indicator (b) should glow on. Note: Channel switch on both Parent's unit and Baby's unit must be in the same position. i.e. If Parent's unit channel switch position is in channel 'A', then Baby's unit channel RESU net ISR aMaee MES MEN RUE SALEM Tess SH ter UEGMEMeee AaSMNNMaA Ce He TeuMSE ae saeanrie switch position MUST also in channel 'A'. Wrong channel positioning will cause malfunction of the system. EZ * Mains adaptor may be an optional item.
* Read and follow all warnings and instructions supplied by the battery manufacturer. Parent's Unit
* When insert the batteries, make sure that the (+) and (-) terminals face in the correct To operate the Parent's unit via the mains adaptor * +(DC 6V 100mA), just plug the directions. adaptor into a convenient wall power socket and make sure you switch the power on if ee ee OH Never use batteries that shows signs of leaking or cracking. To prevent leaking or bursting, never mix batteries of different type, brand, age or charge. Used batteries should not be discarded in fire. Keep all batteries away from children. DO NOT USE RECHARGEABLE BATTERIES. the socket has a switch. Turn on the Parent's unit by turning the Volume/ on/off switch (n), the LED power indicator (i) should glow on. Make sure both channel on Baby's unit and Parent's unit are in same position as mentioned on the above paragraph. You can use the Parent's unit to watch and listen to your baby.
* Mains adaptor may be an optional item.