Wireless-AC|1200M Repeater/Router/AP LED Explanation Signal
(Repeater Mode) The AC MiNi Router is connected to the router or AP, but is too far away from the router or AP. The AC MiNi Router is connected to the router or AP, and is in a good location. The AC MiNi Router is connected to the router or AP, but is too far near from the router or AP. This button is used to restore the AC MiNi Routers factory default settings. Restore the default setting from Advanced->System->Load default->Load default of the AC MiNi With the AC MiNi Router powered on, use a pin press the Reset Button for less than 8 seconds , then Button and Port Explanation WPS Button: If your Wireless Adapter supports WPS function, you can press the WPS button and then press the WPS button to establish a secure connection between the Wireless terminal devices and the AC MiNi Router. Reset Button:
There are two ways to reset the AC MiNi Router:
Option One:
release the button and wait the AC MiNi Router to reboot to its factory default settings. Option Two:
Routers Web-based Management page. Power on/o Button:
WAN Port:
In Router mode, its used for connecting to the DSL/cable Modem or Internet. In Repeater/WISP mode, its used for connecting to Ethernet-enabled device, working the same as the Ethernet port. In Access Point mode, its used for connecting to front router or Internet. LAN Port:
such as Internet TV, DVR, Gaming console and so on. Please note that this port is not allowed to be connected with router. One 10/100Mbps RJ45 Ethernet port used to add wireless connectivity to an Ethernet-enabled device This button is used to power on or o the AC MiNi Router. One 10/100Mbps RJ45 Ethernet port. Applicable Model:LV-AC09 Quick Installation Guide 1 Power on Plug the AC MiNi Router into an electrical outlet. 2 Connect the AC MiNi Router 3 via Ethernet Cable Disable the Wi-Fi on your computer. Connect the AC MiNi Router to your computer via an Ethernet cable. via Wireless Disconnect the Ethernet (wired) connecon to your computer. Click the Wi-Fi icon on the taskbar and connect to the AC MiNi Router's network (
Wireless-AC_2G/5G
). Open a web-browser and type Congure the AC MiNi Router 1. window will appear. Select the language for the installation, and then enter Password, Then click the button or press the Enter key to log in. http://mywi.net Submit in the address eld. After a moment, a login admin for the Language English Password Submit Language - Select the Language from the drop-down list. The default setting is Password -
2. After successful log in, you can click the Operation Mode you need and click Next Enter the password for Login. The default password is Wizard go on conguring. admin
. to quickly congure your router. Select the English
. Not connected Connections are available Wireless Network Connection Wireless-AC_2G Wireless-AC_5G Connect automatically Connect Operaon Mode Gate Way Wireless AP Mode Wireless Repeater Mode WISP Next Gateway Mode(Default) Stand Wireless Router Mode:This router connect to Internet by WAN port, and then other terminal devices can connect to this router by wireless connection or connect to this routers LAN port by wired. The Subnet Mask is used for the WAN IP address, it is usually 255.255.255.0. IP Address - This is the WAN IP address as seen by external users on the Internet (including your ISP). Enter the IP address into the eld. Subnet Mask -
Gateway -
Primary DNS -
Secondary DNS(option) -
PPPoE User Name -
PPPoE Password -
Enter the User Name provided by your ISP. Enter the Password provided by your ISP. If your ISP provides another DNS server, enter it into this eld. Enter the DNS Server IP address into the box if required. Enter the gateway IP address into the box if required. GateWay If Select the very type go on conguring. is selected, Click drop-down menu of WAN Mode, and then WAN Connection Type will appear, If the connection type is
, Static IP Address b. the next screen will appear as shown below. Congure the following parameters and then click to continue. Next a. If the connection type is Dynamic IP Address,Please click to continue. Next c. If the connection type is PPPoE, the next screen will appear as shown below. Congure the following parameters and then click Next to continue. SSID(2G)/SSID(5G)- Enter a value of up to 32 characters. The same name of SSID
(Service Set Identication) must be assigned to all wireless devices in your network. The default SSID is set to be
. Wireless-AC_5G Security -
setting is Security key -
is set as the Security Type, You can enter ASCII characters between 8 and 63 characters or 8 to 64 Hexadecimal characters. you can choose the security type on the drop-down list. The default OPEN Wireless Password, When WPA/WPA2PSK Wireless-AC_2G and
. Enter SSID and Security, then click Note:Do not close this window,the window will automatically close when setup is complete. to complete setup. Apply Wireless AP Mode Raditional wired router realize wireless function:This router can connect to uplink routers LAN port by wired connection,user terminal can connect to this router by wireless connection. If Wireless AP Mode is selected,The Wireless settings page will appear as shown below. SSID(2G)/SSID(5G)- Enter a value of up to 32 characters. The same name of SSID
(Service Set Identication) must be assigned to all wireless devices in your network. The default SSID is set to be
. Wireless-AC_5G Security -
setting is Security key -
is set as the Security Type, You can enter ASCII characters between 8 and 63 characters or 8 to 64 Hexadecimal characters. you can choose the security type on the drop-down list. The default OPEN Wireless Password, When WPA/WPA2PSK Wireless-AC_2G and
. Enter SSID and Security,then click Apply to complete setup. Wireless Repeater Mode Extand wireless signal comprehensively:This router can connect to uplink wireless router by wireless connection,user terminal can connect to this router by wired or wireless connection. If Wireless Repeater Mode is selected,The Wireless Repeater(WDS) page will appear as shown below. WISP Mode Wireless used as WAN port:This router can connect to uplink wireless router by wireless connection,at the same time,it can extend wireless signal for other devices connection. If WIPS is selected,The Wireless ISP (APClient) page will appear as shown below. Select the SSID of the target network and insert Repeater SSID and the key of your network. the default Repeater SSID is set to be name). Then click Note: The Security Key is the same as your Wireless Router.
(xxxx indicates The Main Routers wireless network xxxx_2G_Ext / xxxx_5G_Ext to complete setup. Apply Select the SSID of the target network and insert Repeater SSID and the key of your network. the default Repeater SSID is set to be name). Then click Note: The Security Key is the same as your Wireless Router.
(xxxx indicates The Main Routers wireless network xxxx_2G_Ext / xxxx_5G_Ext to complete setup. Apply Client Mode The MiNi Router can be used as a wireless adapter to connect any Ethernet-only device such as a Blu-ray player, game console, DVR, or smart TV to your Wi-Fi network. First, connect the MiNi Router to your router using Repeater Mode or WISP Mode. Then connect your Ethernet-only device to the MiNi Router via an Ethernet cable. Congure Wireless Key Click Wireless located at the home page,Thefollowing message will be displayed on your web browser. Change Default Access Default Access of The AC MiNi Router is Address of The AC MiNi Router is 192.168.1.253. Click Advance -> Internet-> LAN Settings located at the home page, the following message will be displayed on your web browser. http://mywi.net
, and Default IP Change Management password Default password of The AC MiNi Router is "
admin on the login prompt when accessed from web browser. There's a security risk if you don't change the default password, since everyone can see it. This is very important when you have wireless function enabled. Click Advance -> System -> Password located at the home page, the following message will be displayed on your web browser.
", and it's displayed Insert Repeater SSID and the Security key of your network. Click to save the sengs. Apply Click Apply to save the settings. Note: If you change the IP Address of LAN or Domains, you must use the new IP Address or Domains to log in the router. Click Apply to save the sengs. Firmware Upgrade The system software used by this AC MiNi Router is called computer, when you replace the old application with a new one, your computer will be equipped with new function. You can also use this rmware upgrade function to add new functions to your router, even x the bugs of this router. 1) Click Advance -> System -> Upgrade Firmware located at the home page, the following message will be displayed on your web browser.
, just like any applications on your rmware 2) Click Browse button rst; you'II be prompted to provide the lename of rmware upgrade le. 3) After a rmware upgrade le is selected, click Upload button. and the AC MiNi Router will start rmware upgrade procedure automatically. The procedure may take several minutes, please be patient. Factory Default 1) Click Advance -> System -> Load default, and you can restore the congurations of the router to factory defaults on the following screen. 1) Click the Load default button to reset all conguration settings to their default values. The default Password: admin The default IP Address: 192.168.1.253 The default Subnet Mask: 255.255.255.0 Note: Any settings you have saved will be lost when the default settings are restored. Using WPS Wi-Fi Protected Setup makes it easy to connect other Wireless terminal devices to your network through the AC MiNi Router. Note: your Wireless terminal devices should support WPS. Connecting devices to your network through the AC MiNi Router. 1. Press the WPS Button on the client device. 2. Press and hold the WPS Button on the side of the AC MiNi Router for one second, the WPS LED on the Wireless-N MiNi Router will be ashing. When the connection is complete, the WPS LED will be o. Note: If using the AC MiNi Routers WPS, be sure to click OK within two minutes or you will have to start over. Note:
The entire operation of this product must be limited to indoor use and should not be used outdoors.