FCC ID: 2AVB6-PA10006882 Touch-it CE OEM

Instruction manual Touch-itsCE OEM glass 7 12/2021 www.christ-es.com Touch-it CE OEM glass 7 Instruction Manual Identification Product description 2.1 Housing Variant CE OEM glass Description Hardware 3.1 External Interfaces Environmental Conditions 4.1 IP Protection Class Assembly and Commissioning 5.1 Mounting CE OEM glass Maintenance 6.1 Cleaning 6.2 Maintenance 7 Technical Data 7.1 Mechanical Specifications 7.2 Electromagnetic Compatibility 7.3 Environmental Conditions 7.4 Display Specifications 8 Standards and Approvals 8.1 CE Marking 8.2 RoHS 8.3 Electromagnetic Compatibility 8.4 FCC Approval 8.5 Environmentally Appropriate Disposal 9 Technical Support 9.1 Device Seal 1 2 3 4 5 6 3 5 6 10 10 12 12 13 14 15 15 15 16 16 16 16 17 20 20 20 20 20 21 22 22 Document No.: PA10009463 2 / 24 Dez. 2021, Revision 01 Touch-it CE OEM glass 7 Instruction Manual 1 Identification Target group This document is not intended for end customers! Necessary safety instructions for the end customer must be passed on by the machine builder or system provider and adopted in the respective national language. This product has not been designed, developed and manufactured for use that creates fatal risks and hazards without exceptionally assured safety measures. These include death, injury, or serious physical harm or otherwise caused loss. These represent nuclear response monitoring, nuclear control systems, air traffic control, mass transportation control, medical life support systems, and weapons systems con-

trol. Intended use Technical changes Christ-Electronic Systems GmbH reserves the right to change the information, designs and technical data contained in this documentation without prior notice. No part of this documentation may be reproduced in any form or processed, duplicated or distributed using electronic systems without the prior written consent of Christ Electronic Systems GmbH. Even trans-

lation into another language requires written permission. This documentation is entrusted exclusively to the owner of the device or employees of Christ Electronic Systems GmbH for personal use. Trademark and product names are trademarks or registered trademarks of their respective owners. The following editions of the manual have already been published:

Comment First edition Adding the name plate Copyright Trademarks History Version 10/2021 12/2021 Table 1: History Document No.: PA10009463 3 / 24 Dez. 2021, Revision 01 Touch-it CE OEM glass 7 Instruction Manual Design of safety instructions DANGER Indicates an imminent danger Failure to follow the instructions may result in death or serious injury WARNING Indicates a dangerous situation Failure to observe this warning may result in serious injury or major damage to property CAUTION Indicates a possible dangerous situation Failure to observe the advice can result in injuries or property damage NOTICE Indicates user tips and useful information Important information to avoid malfunctions Document No.: PA10009463 4 / 24 Dez. 2021, Revision 01 Touch-it CE OEM glass 7 Instruction Manual Product description 2 Every industry has its own requirements for machine and system operation. To meet all of them, there are different housing variants with industry-specific features. Above all, special areas of application or special environmental characteristics demand the greatest possible adaptability in the design of the touch panels. In order to meet any requirements, Christ develops so-called OEM solutions. These are equipped with special customer-specific features. The wide variety of OEM touch panels in terms of housing design, processor characteristics, interfaces, inch size and multi-touch technology enables customised implementation of customer requirements. Document No.: PA10009463 5 / 24 Dez. 2021, Revision 01 Touch-it CE OEM glass 7 Instruction Manual 2.1 Housing Variant CE OEM glass Illustration 1: CE OEM glass Front Illustration 2: CE OEM glass Rear 1 2 Customised Mounting Control Element Area Table 2: CE OEM glass Front and CE OEM glass Rear Illustration 3: Dimensions CE OEM glass Size 7"

A 270 Table 3: Dimensions CE OEM glass

* With interfaces and control elements up to 145.2 mm B 218.5 C 79*

Document No.: PA10009463 6 / 24 Dez. 2021, Revision 01 Touch-it CE OEM glass 7 Instruction Manual Properties Illustration Pushbutton Series SHORTRON base-plate mounting Degree of protec-

tion IP65 Travel 2.3 mm Illumination Yes, white LED Labeling Option Yes Front Bezel Silver-Coloured Operating Tem-

perature

-25C ... 70C Contact Elements max. 2 x NC / 2 x NO / 1 x NC +

1 x NO Nameplate Blue, Yellow, Green, Transparent, White Key Switch Series SHORTRON base-plate mounting Degree of protec-

tion IP65 Switching function Maintained action Illumination Labeling Option No No Front Bezel Silver-Coloured Operating Tem-

perature

-25C ... 70C Zeichnung Beispiel-

haft Contact Elements max. 2 x NC / 2 x NO / 1 x NC +

1 x NO Document No.: PA10009463 7 / 24 Dez. 2021, Revision 01 Touch-it CE OEM glass 7 Instruction Manual Illustration Emergency Stop Table 4: Compnents of the Control Elements Properties Series Type QUARTEX-R QRUV IP65 Degree of protec-

tion Illumination Labeling Option No No Front Bezel Yellow Operating Tem-

perature

-30C ... 70C Contact Elements max. 5 (NC / NO) Switching Position Indicator Yes Release Twist right or left Anti-lock Collar Yes Illustration 4: Positions of the Control Elements Document No.: PA10009463 8 / 24 Dez. 2021, Revision 01 Touch-it CE OEM glass 7 Instruction Manual P1 P2 P3 P4 P5 P6 Emergency Stop Dummy Plug 1 x Emergency Stop Push Button, non latching, normally open, C1 24 VDC, transpar-

ent lens, lighted, labelled Dummy Plug Push Button, non latching, normally open, C1 24 VDC, transpar-

ent lens, lighted, labelled Keylock Switch, latching, normally open, 1 x 90, Shape V, 1 x key re-movable position (left) Push Button, non latching, normally open, C13, C14 and C23, C24 floating, transparent lens, lighted Document No.: PA10009463 9 / 24 Dez. 2021, Revision 01 Touch-it CE OEM glass 7 Instruction Manual 3 Description Hardware 3.1 External Interfaces Intercontec 627 AEG A 384 MD 36 00 002K 600 PIN Function Description PIN Function Description 1 GND Ground 14 E_C3 2

+ 24 V

+ 24 VDC 15 E_C6 3 4 5 6 7 8 9 Foot Switch C24 Digital In-

put 1 Digital Output 1 Digital In-

put 2 Foot Switch Contact 24 16 E_C5 Digital Input 1 17 E_C8 Digital Output 1 18 E_C7 Digital Input 2 19 P5_C13 P3_C2 Position 3 Contact 2 20 P5_C14 P3_LED Position 3 LED 21 P5_C23 P1_C2 Position 1 Contact 2 22 P5_C24 10 P1_LED Position 1 LED 23 P4_C13 Emergency Stop Contact 3 Emergency Stop Contact 6 Emergency Stop Contact 5 Emergency Stop Contact 8 Emergency Stop Contact 7 Position 5 Contact 13 Position 5 Contact 14 Position 5 Contact 23 Position 5 Contact 24 Position 4 Contact 13 Position 4 Contact 14 11 E_C2 12 E_C1 13 E_C4 Emergency Stop Contact 2 Emergency Stop Contact 1 Emergency Stop Contact 4 24 P4_C14 25 NC Not Connected 26 FE Functional Earth Table 5: Pinout Intercontec 627 AEG A 384 MD 36 00 002K 600 Binder 86 0632 1000 00004 PIN Function Description 1 2 3 4

+ 24 V

+ 24 V GND

+ 24 VDC

+ 24 VDC Ground Foot Switch C24 Foot Switch Contact 24 Table 6: Pinout Binder 86 0632 1000 00004 Document No.: PA10009463 10 / 24 Dez. 2021, Revision 01 Touch-it CE OEM glass 7 Instruction Manual Binder 09 3732 90 04 PIN Function Description 1 2 3 4 TX +

RX +

TX -

RX -

Transmit Data +

Receive Data +

Transmit Data -

Receive Data -

Table 7: Pinout Binder 09 3732 90 04 Document No.: PA10009463 11 / 24 Dez. 2021, Revision 01 Touch-it CE OEM glass 7 Instruction Manual Environmental Conditions 4 WARNING Insufficient air supply to the device Overheating Never cover the device completely or operate it in a small, unventilated housing 4.1 IP Protection Class The protection class only can be guaranteed under the following conditions:

The device is installed correctly All components and covers of the interfaces are assembled Compliance with all environmental conditions Document No.: PA10009463 12 / 24 Dez. 2021, Revision 01 Touch-it CE OEM glass 7 Instruction Manual 5 Assembly and Commissioning This chapter describes all the steps for assembly. The following warnings are safety instructions that must be applied throughout the assembly chapter and in every other life cycle of the device. DANGER Danger from electric shock, explosion or electric arc Serious injury or death Pull out the mains plug and do not open the covers WARNING Dropping a device Injuries and bruises to the legs and / or feet Wear safety shoes Note for the installation site This device is not designed for outdoor use. Make sure that the ambient temperature and humidity are within the ranges which are specified under Environmental Conditions. Do not install the device directly in the sunlight. Make sure that the device is installed so that is accessible for the operator. Installation instructions Check the package contents for any visible damage and for completeness. In case of damage, do not install the device and contact the Christ Service. Document No.: PA10009463 13 / 24 Dez. 2021, Revision 01 Touch-it CE OEM glass 7 Instruction Manual 5.1 Mounting CE OEM glass Illustration 5: Mounting CE OEM glass The unit is mounted on the marked threaded bolts. The customer determines the fastening utensils and the tightening torque. Christ accepts no liability for damage caused by this fastening. Document No.: PA10009463 14 / 24 Dez. 2021, Revision 01 Touch-it CE OEM glass 7 Instruction Manual 6 Maintenance 6.1 Cleaning The following chapter describes maintenance measures that can be performed by a qualified end user. DANGER Triggering unintended functions Loss of control of the plant / machine / device The unit may only be cleaned when it is switched off or unplugged. To clean the device, use a soft cloth moistened with detergent solution or screen cleaner. The cleaning agent must not be applied directly to the device. Under no circumstances may aggressive solvents, chemicals or scouring agents be used. 6.2 Maintenance It does not require any maintenance on the part of the user. Document No.: PA10009463 15 / 24 Dez. 2021, Revision 01 Touch-it CE OEM glass 7 Instruction Manual 7 Technical Data 7.1 Mechanical Specifications Housing Weight Dimensions Mounting Cooling Aluminium / Silver, Black max. 1.5 kg See Table Dimensions Customised Mounting Passive Table 8: Mechanical Specifications 7.2 Electromagnetic Compatibility Emitted Interference EN55032 Class A Immunity of supply line DC 2 kV according to IEC 61000-4-4; EFT 0,5 kV according to IEC 61000-4-5; Surge asymmetrical Immunity of signal lines 1 kV according to IEC 61000-4-4; EFT ESD 4 kV Contact discharge according to EN61000-4-2 8 kV Air discharge according to EN 61000-4-2 Immunity of conducted emission 3 V 150 kHz 80 MHz, 80% AM nach IEC 61000-4-6 Immunity of high-frequency radi-

ation 3 V/m 80 MHz 1 GHz, 80% AM nach IEC 61000-4-3 3 V/m 1 GHz 6 GHz, 80% AM nach IEC 61000-4-3 Table 9: Electromagnetic Compatibility 7.3 Environmental Conditions Operating Temperature 0 ~ 50 C Storage Temperature

-10 ~ 70 C Humidity 5 ~ 80 % (non condensing) Protection Class IP65 (IP20 rear) Transportation and Storage Suitable packing increases shock resistance max. Installation Altitude 2000 m Cooling Natural Air Convection Table 10: Environmental Conditions Document No.: PA10009463 16 / 24 Dez. 2021, Revision 01 Touch-it CE OEM glass 7 Instruction Manual 7.4 Display Specifications Color Depth Lifetime Viewing Angle

(right/left/up/down) Backlight Touch Technology Table 11: Display Specifications 8 bit min. 50,000 h min. 85/85/85/85 LED PCAP NOTICE Pixel Errors Due to the manufacturing process, displays may contain faulty pixels (pixel er-

rors), which do not constitute a claim or warranty. Document No.: PA10009463 17 / 24 Dez. 2021, Revision 01 Touch-it CE OEM glass 7 Instruction Manual The international standard ISO 9241-307:2009 defines, on an international level, the maximum possi-

ble pixel errors in an LC-display. This standard discribes different error types, in consideration of differ-

ent pixel error classes. There are the following pixel error classes, each with three differnet error types:

Maximum acceptable errors per 1 Mio. pixels according to ISO 9241-307:2009 error class error type 1 pixel constantly il-

luminatied error type 2 pixel constantly dark 0 1 2 5 50 0 1 2 15 150 error type 3 subpixel con-

stantly illumi-

natied 0 n = 0 to 2 2 - n n = 0 to 5 5 - n max. 50 max. 150 error type 4 subpixel con-

stantly dark 0 2 x n + 1 2 x n max. 50 max. 150 Why this classification of errors?

Each pixel of a display contains three subpixels which have the basic colors red, green and blue. The combination makes it possible to show a wide spectrum of colors. Considering for example the display solution of 1280 x 800 pixels, thereof a total of 1,024000 pixels or 3,072000 subpixels are embedded in the display area. This means , the display holds 3,072000 single transistors at an area of 261.1 mm by 163.2 mm. These figures make it clear that it is not possible to specifically produce defect-free displays even by to-

day's manufacturing standards. Christ Electronic Systems GmbH therefore adapts to the corresponding requirements of most interna-

tional manufacturers. The displays must always comply with error class II. If the permissible number of errors of the pixel error class II is not exceeded, there is also no complaintable "failure" of the display. Refering to the calculation, the following errors can occur in the display:

Max. 2 constantly illuminated and 2 constantly dark pixels Max. 5 constantly illuminated or 10 constantly dark subpixel Avoid burn-in on displays NOTICE Images that do not change

"Image shadows", "ghost images" arise Changing displayed images, screen saver, energy-saving mode With LC displays, so-called "ghost images" or "image shadows" can occur under certain circumstances. These are images that remain from the previous image and are felt to be "burnt into" the display. These do not remain forever. If "image shadows" occur, the device should be switched off for a longer period of time so that the burnt-in image disappears. 0 I II III IV Document No.: PA10009463 18 / 24 Dez. 2021, Revision 01 Touch-it CE OEM glass 7 Instruction Manual To avoid "ghost images" or "image shadows", the following behaviour is recommended:

Do not display still images over an extended period of time Change standing images at short intervals Switch off the unit or use the energy-saving mode when you do not need it Use the screen saver function Document No.: PA10009463 19 / 24 Dez. 2021, Revision 01 Touch-it CE OEM glass 7 Instruction Manual 8 Standards and Approvals 8.1 CE Marking The device has been tested in accordance with the applicable EU directives and the associated harmonized standards. 8.2 RoHS NOTICE Decleration of Conformity The declaration of Conformity can be downloaded from the Christ Electronic Systems Homepage. The device complies with the requirement of the EU Directive RoHS 2011/65/EU. 8.3 Electromagnetic Compatibility The device complies with the requirements of the EU Electromagnetic Compatibility Directive 2014/30/EU with the harmonized standards listed below:

EN 55032: 2015 Class A Electromagnetic compatibility of multimedia equipment - Emis-

sion Requirements EN 55035: 2017 Electromagnetic compatibility of multimedia equipment - Immun-

ity requirements 8.4 FCC Approval The device meets the requirements of FCC for approval in the USA and Canada. This has been tested and confirmed by SGS. FCC (Federal Communications Commission) The device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause any harmful interference.

(2) This device must accept any interference received, including interference that may cause undesired operations. Changes or modifications not expressly approved by the party responsible for compliance could void theusers authority to operate the equipment. NOTE:This equipment has been tested and found comply with the limits of Class A digital device, pursu-

ant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial environment. This equipment generates, uses and can radiate ra-

dio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equiment in a resident area is likely to Document No.: PA10009463 20 / 24 Dez. 2021, Revision 01 Touch-it CE OEM glass 7 Instruction Manual cause harmful interference in which case the user will be required to correct the interference at his own expense. Validity Touch-it CE OEM glass 7, Prod. ID: PA10006882 Touch-it CE OEM glass 7, Prod. ID: PA10xxxxxx Where "xxxxxx" in the ID Number may be any numeric characters. These models are variants of the Touch-it CE OEM glass 7 and are different regarding the interface connectors and the pushbuttons. These variants are subset of the ID: PA100006882. Name Plate Illustration 6: Name Plate 8.5 Environmentally Appropriate Disposal The device must not be disposed of with domestic waste. The appliance complies with the requirement of the EU Directive WEEE 2012/19/EU, which is symbolised by the symbol with the crossed-out dustbin. In order to enable environmentally friendly recycling, the various materials must be separated from one another. Disposal must be carried out in accordance with the applicable legal regulations. Component parts Disposal Enclosure Electronic Metal Recycling Electronics Recycling Paper / cardboard packaging Paper / Cardboard boxes Recycling Plastic packing materials Plastics Recycling Document No.: PA10009463 21 / 24 Dez. 2021, Revision 01 Touch-it CE OEM glass 7 Instruction Manual 9 Technical Support Despite the highest quality standards and detailed function tests of all our products, daily use of our de-

vices can always lead to damage or failure of a wearing part. The failure of a machine in production costs a lot of money. That is why the Christ company processes complaints as quickly as possible. You can send the device to us without prior notice. All you need to do is fill out the cover letter for the repair and enclose it with the touch panel or IPC so that the service department can start the repair quickly. When the device arrives, it goes through a defined process that clearly documents all processes and makes the respective status traceable. As soon as your panel or IPC is registered in our system, you will receive a confirmation of receipt so that you can also get a precise overview. Technical Support can be contacted as follows:

Service, Repair and Technical Support Phone: +49 8331 8371-500 Fax: +49 8331 8371-497 E-Mail: service@christ-es.de Or directly via the Homepage. Christ Service 9.1 Device Seal A device seal is affixed to every Christ device in order to prove whether the device has been opened by a third party. In case of a defect, please do not open the device, but contact our service department. They will discuss the further procedure with you. Document No.: PA10009463 22 / 24 Dez. 2021, Revision 01 Touch-it CE OEM glass 7 Instruction Manual Index of Illustration Illustration 1: CE OEM glass Front Illustration 2: CE OEM glass Rear Illustration 3: Dimensions CE OEM glass Illustration 4: Positions of the Control Elements Illustration 5: Mounting CE OEM glass Illustration 6: Name Plate 6 6 6 8 14 21 Document No.: PA10009463 23 / 24 Dez. 2021, Revision 01 Touch-it CE OEM glass 7 Instruction Manual Index of Tables Table 1: History Table 2: CE OEM glass Front and CE OEM glass Rear Table 3: Dimensions CE OEM glass Table 4: Compnents of the Control Elements Table 5: Pinout Intercontec 627 AEG A 384 MD 36 00 002K 600 Table 6: Pinout Binder 86 0632 1000 00004 Table 7: Pinout Binder 09 3732 90 04 Table 8: Mechanical Specifications Table 9: Electromagnetic Compatibility Table 10: Environmental Conditions Table 11: Display Specifications 3 6 6 8 10 10 11 16 16 16 17 Document No.: PA10009463 24 / 24 Dez. 2021, Revision 01

m AbensraGe st COAST oor eee TABCTRONIC SYSTEMS = were Cornet-en ce Touch-it CE OEM glass 7 Prod. 1D: PA10006882 Rev. 1 Serial no 0216031-000-001 4]10.2021 input: m 24V MAC 12.34 56:78:90:ab

; 12:34.58:78:90:ac eh

| FCCID: 2AVB6-PA10006882 sensing xc Ee This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions (1)

@ may not cause harmful nterference and (2) this device must cept any interference received, including y Cause undesired oy

ELECTRONIC SYSTEMS Date: 03.12.2021 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: 2AVB6-PA10006882 / 2AVB6-PA 1 Oxxxxxx To whom it may concem:

We, the undersigned, hereby authorize SGS North America Inc. to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, | acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Christ Electronic Systems GmbH. This authorization is valid until further written notice from the applicant. Name (Printea): Title:

Ingo Roehr Certification Manager Signature:

a On behalf of Company:

Christ Electronic Systems GmbH es .._.. Porepnorne.

+498331/8371-116

a) b) c) d) e) f) g) SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Declaration Applicant Legal Business Name Christ Electronic Systems GmbH Alpenstrasse 34, 87700 Memmingen Address Grantee Code FCC ID Contact Email Contact Phone Authorized Contact Name 2AVB6 PA10006882 Ingo Rhr iroehr@christ-es.de

+4983318371116 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare;

in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

labeling the equipment with the exact FCC ID as specified in this application,

(1)

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules, if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements.

(1)

(2)

(3) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. the Applicant shall, upon request by SGS, at the Applicants expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature:

Date: 03.12.2021 Print Name:

Title:

Ingo Rhr Certification Manager

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database Applicant Declaration Rev:0.0

Alpenstrasse 34 Memmingen, 87700 Germany To: SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From: Christ Electronic Systems GmbH Regarding: Confidentiality Request regarding application for FCC ID 2AVB6-PA10006882 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commissions rules, the applicant hereby requests confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Jeremy Pickens, Agent for Christ Electronic Systems GmbH SGS North America SGS North America Inc. Connectivity & Products 620 Old Peachtree Road Suite 100 Suwanee GA 30024 t (770) 570-1800 f (770) 277-1240 www.sgs.com Member of the SGS Group (SGS SA)