active noise-canceling headphones ANC button press - ANC on/ambient/ANC off double press - voice assist press - vol. up hold - next track/reject call/transfer call press - play/pause/
answer/end calls double press - redial hold - on/off/pair press - vol. down hold - prev. track/
mute call aux. port indicator light charge port power light mic left side mic right side included Bluetooth Wireless ANC headphones USB-C charging cable 3.5mm audio cable Carrying case indicators Quick flashing white - pairing/re-pairing Single flashing white - paired Rapid flashing white - incoming call Intermittent flashing white - active call/streaming Solid red - low power/charging Red light off - charging complete Ascending tones - power on Descending tones - power off Three rapid tones - ready to pair Two rapid dings - low battery Quick ascending tone - max volume Quick descending tone - min. volume pairing When pairing for the first time, while the headphones are off, press and continuously hold the power button for 7 seconds to turn on the headphones. The indicator on the right will quickly flash white when its ready to pair Use the Bluetooth settings on your phone to pair with HEYDAY HEADPHONES 03 Slow single flashing white light - pairing successful note: holding the power button for 4 seconds will power headphones on/off; holding for 7 seconds while the headphones are off with turn the headphones on and enter pairing mode ANC/AMB button indicators ANC/Ambient solid white - ANC/Ambient on Two ascending tones - ANC ON Two high tones - Ambient ON Two descending tones - Ambient OFF ANC (Active Noise-Canceling)/AMB (Ambient) Utilize the ANC button to cycle the three different active noise-cancellation settings Pressing the button once from off will enter ANC mode (Active Noise-
Cancellation) and is indicated with two ascending tones ANC mode reduces outside noise at least 27dB reduction and makes your music the focus of your trip instead of the people around you Pressing the button again (twice from off) will enter AMB mode (Ambient) and is indicated by two high tones AMB mode only lets in high frequency sounds this way you can still get some quiet time on a bus or airplane but never miss an announcement Pressing the button again (three from off) will turn OFF the Active Noise-
Cancellation and is indicated with two descending tones If the headphones are turned off when ANC or AMB is active, that mode will be activated when the headphones are turned back on note: ANC mode/AMB mode only works when the Bluetooth turned on charging Plug the USB-C end of the charging cable into the headphones Plug USB end of the charging cable into a power supply of at least DC 5V 1A warning: please use UL compliant power supply Full charge requires approximately 2.5 hours Charging is complete when red light turns off note: headphones cannot playback when charging aux/line in Insert the AUX cable into headphone AUX port Insert opposite end of the AUX cable into the media source troubleshooting lf the headphones are not working correctly, turn them on/off to reset lf the headphones won't turn on, recharge the battery and try again lf the headphones won't charge, make sure the power supply works, is 5V 1A , and not damaged lf the headphones make no sound or do not show as an available device, make sure they are not paired to a different device already To re-enter pairing mode hold the power button for 7 seconds when headphones are off need some help?
Cant get it to pair? Have a question or comment?
call us at: 877-698-4883 or: 877-MyTgtTech online at: TargetTechSupport.com safety Do not use near any water source Do not modify or repair this device Do not use in high temperatures or extreme weather Do not use chemical detergents to clean your device, use a soft dry cloth FCC ID:2AO23- ANC2 Model: ANC2 Input: DC5V 1A Made in China This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. Target Corp. Mpls. MN, 55403 Phone: 612-304-6073 For qualified repair specialists requesting repair information and parts please contact the original manufacturer at customersupport@gemsfindyours.com