FCC ID: 2AO23-QIC43 Magsafe stand/ Magsafe pad

magsafe stand/

magsafe pad front back quick tips included charging The device should stick firmly to the stand when charging Thick phone cases as well as some materials can interfere with MagSafe charging This is a high speed magnetic charging stand, make the most of the charger by using the Power Delivery wall plug that was packaged with it; using a different power source may charge your device at a slower speed Magnetic charging stand with attached charging cable Power Delivery wall plug Place the charging stand on a sturdy flat surface Connect the Power Delivery wall plug to the wall outlet using the attached USB-C cable (recommended) If you need to use a different power source make sure it is a USB power supply of DC 9V 2.22A minimum warning: please use UL compliant power supply Place your MagSafe compatible device onto the magnetic charging stand; the device will stick to the stand and the screen will indicate that it is charging

(note: MagSafe compatible device can be placed vertically or horizontally) Remove credit cards or any card with a magnetic strip to prevent damage to the cards before charging Charge time will vary by device troubleshooting If youre having issues charging use the tips below to help:

When properly aligned the device will stick to the stand and the charging screen will appear If the device will not stick to the charging stand, remove the case and try again Does not charge Apple Watch Double check that the USB-C cable and Power Delivery wall plug are plugged in Certain phone cases may interfere with MagSafe charging; remove the phone case for best results Double check the placement of the device on the magnetic charging stand; for best results, the center of the device should be on the center of the magnetic charging stand MagSafe charging is compatible with iPhone 12 and newer as well as other Qi-enabled devices; please consult your devices user manual if you are unsure if your device is compatible need some help?

Cant get it to charge? Just have a question?

call us at: 877-698-4883 or: 877-MyTgtTech e-mail us at: TargetTechSupport.com safety Remove credit cards and other cards with magnetic strips to prevent damage to the cards Keep the charger away from heat and direct sunlight Do not modify or repair this device Do not use in high temperatures or extreme weather Do not use chemical detergents to clean your device, use a soft dry cloth Immediately unplug it from its power source if it gets wet Remove the protective film on the Power Delivery wall plug before using FCC ID: 2AO23-QIC43 Model: QIC43 Input: DC 9V/2.22A Output: 15W Max Made in Vietnam This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Target Corp. Mpls. MN, 55403 Phone: 612-304-6073 5.7 in

Magsafe stand/Magsafe pad Model: QIC43 Input: Type-C 9V 2.22A Output: MagSafe Charger 15W FCC ID: 2AO23-QIC43 Made in Vietnam MMYY This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

C5266091_X10_Ed.1 Chug, Inc. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request for Confidentiality FCC ID: 2AO23-QIC43 Date: 12/1/2021 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits ID Label/Location Attestation Statement External Photos Block Diagram Schematics Test Report Test Setup Photos Users Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) SDR Software / Security Info Long-Term Confidentiality No No No No No No Short-Term Confidentiality No No No No No Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Michael Clemmer Title: General manager Date: 12/1/2021 1/1

C5266091_X8_Ed.1 Letter of Authorization Chug, Inc. Company: Chug, Inc. Address: 7157 Shady Oak Road, Eden Prairie, MN 55344, USA Product Name: Magsafe stand/ Magsafe pad Model Number: QIC43, QIC42, HKWP2681-15EL, HKWP2701-15EL FCC Identifier: 2AO23-QIC43 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Michael Clemmer Date: 12/1/2021 Title: General manager Signature of applicant:

1/1

Chug, Inc. Model difference statement Product Name: Magsafe stand/ Magsafe pad Model No.: QIC43, QIC42, HKWP2681-15EL, HKWP2701-15EL We (Chug, Inc., 7157 Shady Oak Road, Eden Prairie, MN 55344, USA) hereby state that all the models are the same circuit and RF module, except the model name. Signature:

Name: Michael Clemmer Title: General manager Tel: 612-868-2191 Email: mikeclemmer@gmail.com Date: 12.1.2021