VEABT001ModuleUser'sManual 1. Features Onchiplowpowermicrocontroller 128KBofInsystemprogrammableflash 8KBSRAM OnboardcrystalandPCBAntenna 2. Application Wirelessdatacommunication 3. Pindefinition PinNo. Description 1 2 3 4 5 6 7 BLE_RX BLE_TX WAKE_UP STATUS GND V+
BLE_EN PinType DigitalI/O DigitalI/O Output Input DigitalI/O DigitalI/O DigitalI/O Functions UARTRX UARTTX DigitalI/O DigitalI/O GND VDD VDDEnable 4. Howtouse:
BeforesendinganyUARTCommand,"WAKE_UP10"mustbedoneby externalMCU. IftheCC2640moduleisconnectedtoSmartDevices(Android/iOS),thepin STATUSwillbelogic"1"toinformexternalMCU. Beacon 1. SendCommand'D'/'P'tosendlivemeasureddatafromexternalthrough Beacon. 2. Thisisdefaultmode,andVEABT002modulesenddataonly.Cannot receiveanydata. BLE 1. SendCommand'M'toswitchmodefromBeacontoBLE. 2. Afterthemodeswitchsuccessfully,theexternalMCUcanreceivedata fromSmartphone. Receiver 1. SendCommand'A'/'B'toswitchmodefromBeacontoReceiver. 2. OnlyspecificBeacondatacanbereceived,andtheexternalMCUreceives thedatafromUART 5. Protocol:
UARTBaudRate:115200,8,N,1 Commands
'D':SendMeasuredData ExternalMCUVEABT002Module Starter
#
Len OP D Battery Data ExternalMCUVEABT002Module Starter
>
Len OP D Indi
'P':SendProductInformation ExternalMCUVEABT002Module CK End
(0D0A)h End
(0D0A)h CK Starter
#
Len OP P FP Prod. S/N Cal.Date CK End
(0D0A)h ExternalMCUVEABT002Module Starter
>
Len OP P Indi CK End
(0D0A)h
'M':ModeSwitch ExternalMCUVEABT002Module Starter
#
Len OP M S/N ExternalMCUVEABT002Module Starter
>
Len OP M Indi
'A':ScanProductInformation ExternalMCUVEABT001Module CK CK End
(0D0A)h End
(0D0A)h Starter
'#'
Len OP
'A'
CK End
(0D0A)h ExternalMCUVEABT001Module Starter
'>'
Len OP
'A'
SN APO Batt RSSI CK End
(0D0A)h
'B':ScanMeasuredData ExternalMCUVEABT001Module Starter Len SN
'#'
ExternalMCUVEABT001Module OP
'B'
CK End
(0D0A)h Starter
'>'
Len OP
'B'
APO Batt Data RSSI CK End
(0D0A)h This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices). End Product Labeling This transmitter module is authorized only for use in devices. The final end product must be labeled in visible area with the following:
Contains FCC ID:VEABT001 End Product Manual Information The user manual for end users must include the following information in a prominent location IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or colocation with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for reevaluating the end product (including the transmitter) and obtaining a separate FCC authorization. This device is intended only for OEM integrators under the following conditions:
As long as a condition above is met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). inconjunctionwithanyotherantennaortransmitter.