FCC ID: PIZGH9764 2.4GHz DSST Multi-Handset w/ CID+DAM

2.4 GHz DIGITAL SPREAD SPECTRUM ALL DIGITAL ANSWERING SYSTEM WITH CALLER ID / CALL WAITING

& SPEAKERPHONE IN BASE UNIT 54 CHANNEL AUTOSCAN WITH 4 SEPARATE MAILBOXES MULTIPLE HANDSETS FEATURE Model GH9764 OWNERS MANUAL INSTALLATION AND OPERATING INSTRUCTIONS PLEASE READ THIS MANUAL CAREFULLY BEFORE USE. KEEP FOR YOUR REFERENCE. For installation information, please see Getting Started instructions on page 6 or your separate Quick Start Guide. Visit Us on the Web:

www.uselectronics.info 2004 Bellsouth Corporation Wall Mounting IMPORTANT: The BASE UNIT IN USE LED indicator will light up RED when the HANDSET is properly positioned in the BASE UNIT CHARGE CRADLE and charging. Securely positioning the HANDSET in the BASE UNIT will also prevent the HANDSET from falling. 11 Cordless Telephone Operation Preparing for Use Before you can use your cordless telephone, you must charge the HANDSET for 12 hours. Failure to do so will require more frequent recharging of the BATTERY PACK, See page 44 for more information on the BATTERY PACK. 1. Place the HANDSET on the BASE UNIT for 12 hours. 2. After 12 hours, remove the HANDSET from the BASE UNIT. The RING: HI should be displayed on the LCD Screen. If you see WAIT REG. on the LCD Screen, please do handset registration as described in page 29. NOTE:

Depending on the frequency of use, once the HANDSET is fully charged, it remains functional for approximately 4 hours of continuous use and approximately 5 days when the HANDSET is off the BASE UNIT in STANDBY mode. NO LINE Indicator This telephone checks for an active TELEPHONE LINE connection. If NO LINE appears on the LCD Screen, when the HANDSET is in STANDBY mode, no calls can be made or received from this telephone. Check that the TELEPHONE LINE CORD plugs are connected to the the BASE UNIT wall TELEPHONE JACK and TELEPHONE LINE CONNECTION JACK. If NO LINE continues to be displayed, check that the other phones in the house are working. If none of the phones work, contact your local phone company. Receiving Calls From the HANDSET 1. When the phone rings, lift the HANDSET and press talk button. The HANDSET LCD Screen will the display CALLS and TALKING, and the BASE UNIT IN USE LED indicator will light up GREEN. 2. Start your conversation. 3. To end your conversation, either press the talk button or place the HANDSET on the BASE UNIT. If you place the H A N D S E T on the BASE UNIT CHARGE CRADLE, you activate the automatic STANDBY feature. 12 CALLS TALKING. Cordless Telephone Operation NOTE:

1. The Call Timer will start to count once you press the talk button. 2. The LCD Screen emits light for 5 seconds every time you press any buttons on the HANDSET. 3. When CALLS appears on the LCD Screen, it means that the HANDSET is OFF-HOOK

(connected to the telephone line). Minutes CALLS 00MIN 1SEC 14 Seconds Channel Receiving Calls Using the BASE UNIT SPEAKERPHONE 1. When the phone rings, press the SPEAKER button and begin speaking. 2. The LED Message Display will show 3. The S P E A K E R P H O N E speaker volume can be

. vol +

and adjusted by pressing the

. The LED Message Display will indicate the speaker volume as:

0 - Speaker off 1~8 - Volume from low to high vol -

4. To hang up, press the SPEAKER button again. IMPORTANT In order to utilize the Caller ID feature, you must subscribe to Caller ID service from your local telephone company. 13 Cordless Telephone Operation Placing Calls talk 1. Press the button, the Call Timer starts to count. The HANDSET LCD Screen will display CALLS, and TALKING, and the BASE UNIT IN USE LED indicator will light up GREEN. 2. Listen for a dial tone. 3. Dial the phone number. 4. When you have finished with your call, press the talk button again or place the HANDSET on the BASE UNIT. CALLS TALKING. OR 1. Dial the phone number. 2. Press and hold down the DIAL 7 or the DIAL 10

*7 or the DIAL1+

#1+

button. The BASE UNIT IN USE LED indicator will light up RED. 3. When you have finished with your call, press the talk button again or place the HANDSET on the BASE UNIT. Headset Feature Your telephone can utilize a headset (not included) to be connected to your HANDSET for you to enjoy hands-free communication. Pull out the HEADSET JACK COVER then insert the small plug at the end of the headset into the HEADSETJACK at the right side of the HANDSET. Follow the procedures discussed in Receiving Calls and Placing Calls to receive and place a call. NOTE: When you plug the headset plug into the HEADSET JACK it automatically mutes the MICROPHONE and SPEAKER of the HANDSET. Unplug the headset to return the HANDSET to normal use. Headsets are available at most retail outlets that sell telephone equipment. The HEADSET JACK is compatible with 2.5mm headset plugs only. 14 Caller ID System Operation Redial Feature 1. If you get a busy tone, press the the HANDSET on the BASE UNIT to hang up. talk button or place 2. Later, press the talk button again. 3. Listen for a dial tone. redial 4. Press the save/pause button. This will automatically redial the last telephone number you called in TALK mode. 5. When you have finished with your call, press the talk button again (the BASE UNIT IN USE LED indicator will turn off) or place the HANDSET on the BASE UNIT. NOTE:

If you are too far away from the BASE UNIT, the HANDSET emits beep sounds to warn you that the background noise level is too high for proper communication between the HANDSET and the BASE UNIT. When you hear this sound, you should move closer to the BASE UNIT to reduce the noise level. Otherwise, the call will automatically cut off. 15 Caller ID System Operation Caller ID System This telephone automatically displays an incoming callers name and telephone number together with the date and time of the call. It records up to 80 calls and stores the data in Memory. IMPORTANT: You must subscribe to the Caller ID service from your local telephone company to utilize this feature. Viewing Caller Information During Incoming Calls 1. When there is an incoming call, the name and the telephone number of the caller will automatically appear after the second ring. Press the SHIFT RIGHT a name of more than 11 characters. button to view MICHAEL BROW 6 0 4 - 5 5 5 - 1 2 1 2 10:00AM 8/24 NEW

# 1 BROWING 6 0 4 - 5 5 5 - 1 2 1 2 10:00AM 8/24 NEW

# 1 Time Month/Date Number of calls recorded OR Callers telephone number will appear if the callers name is not available. OR OUT OF AREA will appear if the origin of the incoming call does not support the Caller ID system. OR UNKNOWN will appear if the origin of the incoming call has no name and does not support the Caller ID system. e.g. e.g. OUT OF A R E A O - - - - - - - - - -

10:00AM 8/24 NEW

# 13 TOTAL 42 U N K N O W N U - - - - - - - - - -

10:00AM 8/24 NEW

# 13 TOTAL42 OR PRIVATE and/or P--------- will appear if the callers name and/or telephone number is blocked. OR DATA ERROR will appear if wrong data was received from the telephone line. OR The name stored in the DIRECTORY will appear for an incoming call with matching telephone numbers. MSG WAITING (Message Waiting) The MSG WAITING GREEN LED indicator will blink when there is a message for you from your telephone company if you have subscribed to Voice Mail message service and if you have requested Visual Message Indication from your local telephone company. MSG WAITING will appear on the LCD Screen in STANDBY mode. (To remove the MESSAGE WAITING indicator, see page 28 for detail.) 16 Caller ID System Operation Call Waiting When you subscribe to a Call Waiting service from your local telephone company, this telephone will display the name and number of the second caller while you are having a conversation with your first caller. 1. When you are having a conversation, e.g. this telephone will automatically display the name and number of the second caller. The name will blink. JOHN BROWN 2 3 5 - 6 0 7 - 5 5 1 2 10:00AM 8/24 NEW 13 1st Caller 2. Press the edit flash button to answer the second caller. first callers name and number will be The displayed. The name will blink. 3. When you have finished, press the edit flash button to e.g. continue your conversation with the first caller. If you do not want to interrupt your phone conversation with the first caller, you can advise the second caller to leave a Voice Mail message instead. Voice Mail Function When there is a Voice Mail message for you, this telephone detects a Stutter Dial Tone (if applicable) and the MSG icon on the LCD Screen and the MESSAGE WAITING LED indicator will blink. 2nd Caller ALEX BROWTH 5 0 4 - 5 5 5 - 1 2 1 2 10:00AM 8/24 NEW 14 1. To access your Voice Mail message, press the talk button. 2. After you hear a dial tone, press the button. This will automatically dial the Voice Mail Post Code in your area and connect you to the Voice Mail service provider. NOTE: You must store the Voice Mail Post Code number by using the VOICE MAIL function on page 28. You can also call your Voice Mail service provider by dialing voice mail menu the Voice Mail Access Code number after pressing the talk button. C-F (Forwarded Call) Appears on the upper left hand side of the LCD Screen, when the incoming call has been assigned to your telephone number. L-D-C (Long Distance Call) Appears on the upper left hand side of the LCD Screen, when the incoming call is a long distance call and the service is provided by your local telephone company. Caller List Records call information for up to 80 incoming calls such as callers name and telephone number together with the date and time of the call. After recording a new incoming call, the NEW CALL indicator will blink and the LCD Screen will display:

RING: HI 10:00AM 8/24 NEW 13 TOTAL 42 No. of new calls Maximum calls= 80 17 Caller ID System Operation Viewing the Caller List 1. Press the SCROLL DOWN button to view the latest Caller ID record, or press the SCROLLUP button to view the first Caller ID record, press the SHIFTRIGHT button if the name has more than 11 characters. MICHAEL BROW 6 0 4 - 5 5 5 - 1 2 1 2 10:00AM 8/24 NEW

#1 BROWING 6 0 4 - 5 5 5 - 1 2 1 2 10:00AM 8/24 NEW

#1 2. Press the button to go back to STANDBY mode. (If no active buttons are pressed for 20 seconds or you have viewed the last Caller ID record in the Callers List, the LCD Screen will automatically return to STANDBY mode.) Placing a Call from the Caller List 1. With the HANDSET in STANDBYmode, press the SCROLLDOWN button to select from the latest Caller ID record, or press the SCROLL UP button to select from the first Caller ID record. 2. Press and hold down the DIAL 7 button for a local call, or the DIAL 10

*7 button for a local call with area code, or the DIAL1+

#1+

button for a long distance call. 3. To end your conversation, either press the talk button or place the HANDSET on the BASE UNIT. To place a call from the Caller List in TALK mode, press the steps 1 through 3. talk button, then follow NOTE: You can edit the number before dialing, but you can not SAVE any changes in the Caller List. Editing the Caller List before Dialing or DOWN 1. Press the SCROLL UP 2. Press the edit flash button. button to find the Caller ID record. 3. Move the cursor by pressing the SHIFTLEFT or RIGHT button to the digit you want to change. To erase digits, press the delete scan button. To add digits, use theTELEPHONE KEYPAD

wxyz 9 buttons. 4. Press and hold down the DIAL 7 button for a local call, or the DIAL 10 button for a local call with area code, or the DIAL 1 +

#1+

button for a long distance call. 5. To end your conversation, either press the talk button or place the HANDSET on the BASE UNIT. To save the edited record from the Caller List, follow steps 1 through 3 then press and hold down the redial save/pause button. 18

*7 Caller ID System Operation Saving the Name and Number in the Caller List into the DIRECTORY 1. Press the SCROLL UP button to find the Caller ID record. or DOWN 2. Press and hold down the NOTE:

redial save/pause button. The LCD Screen will show SAVED. It is not advisable to save a telephone number without the corresponding name. This will lead to improper display on PRIVATE and OUT OF AREAcalls. Deleting All Records in the Caller List 1. Press and hold down the delete scan button for at least 3 seconds while in STANDBY mode. 2. The LCD Screen will automatically return to STANDBY mode. ALL DELETE 10:00AM 8/24 NEW 0 TOTAL0 Selective Deleting in the Caller List 1. Press the SCROLLUP or DOWN STANDBY mode. button to find the Caller ID record while in 2. Press and hold down the button for at least 3 seconds, then the LCD Screen will display the next Caller ID record in the CALLER LIST. delete scan DELETE 10:00AM 8/24

# 2 3. Press the button to return to STANDBY mode. Special Note to Caller List for Multiple Handset User In this multiple HANDSET cordless phone, the up to 80 incoming calls caller list are stored in the BASE unit. No matter how many HANDSETS link to the same BASE unit, they share the same caller list. Each HANDSET can view the caller list, place a call from the caller list, delete the record in caller list, and save the record in the caller list into the directory memory of each HANDSET. When a record in caller list is deleted by one of the HANDSET, the other HANDSETS can not view and use the record again. We suggest that each HANDSET user saves the record in caller list, which the number he will call frequently, into the directory memory of his own HANDSET. Name and Telephone Number DIRECTORY This DIRECTORY lets you scroll through the list to find the record you need for one touch dialing. You can store up to 40 names and telephone numbers in the memory. 19 Caller ID System Operation Viewing the DIRECTORY 1. Press the button. DIR DIRECTORY 10:00AM 8/24 TOTAL12 No. of records stored 2. Press the SCROLL UP or DOWN button to find the record you wish to view, press the SHIFT RIGHT telephone number of more than 11 characters. button to view a name or DIR MICHAEL BROW 6 0 4 - 5 5 5 - 1 2 1 2 TOTAL12

# 8 DIR BROWING 6 0 4 - 5 5 5 - 1 2 1 2 TOTAL12

# 8 NOTE: To exit the DIRECTORY List at anytime, press the button. Speed Viewing the DIRECTORY 1. Press the button. 2. Enter the first letter of a name. (See Page 31 for detail of entering a letter.) 3. Press the SCROLLUP button to view all names with the same first letter. Saving in the DIRECTORY 1. Press the button. 2. Press the edit flash button. 3. Use the TELEPHONE KEYPAD buttons to enter the name, (see page 31 for detail) you can store up to 15 characters. To move the cursor to the right, createa

wxyz 9 space, or to enter a new letter, press the SHIFT RIGHT button. 4. Press the SCROLLDOWN button once. 5. Enter the telephone number using the TELEPHONE KEYPAD

wxyz 9 buttons. You can store up to 16 digits. 6. Press and hold down the redial save/pause button. 7. Press the button to go back to STANDBY mode.

(If no active buttons are pressed for 20 seconds, the LCD Screen will automatically return to STANDBY mode.) 20 Caller ID System Operation NOTES: 1. It will not save a duplicate telephone number or a name without the corresponding telephone number in the DIRECTORY. 2. To delete a character or number inside the cursor, press the delete scan button. PREFERRED CALLS You can assign stored numbers a PREFERRED CALLstatus which will generate a special ringer sound at the start of the second ring to any welcome caller in the DIRECTORY. When you are saving the name and number into the DIRECTORY, add a # symbol at the beginning of the name by pressing the

#1+

button. BLOCKED CALLS You can assign stored numbers a BLOCKED CALL status which will disable the ringer sound after the second ring to any caller in the DIRECTORY. When you are saving the name and number into the DIRECTORY, add an * symbol at the beginning of the name by pressing the 7 button.

*7 Editing a Name and Number in the DIRECTORY 1. Press the button. 2. Press the SCROLL UP or DOWN button to find the record you want to edit. DIR MICHAEL BROW 6 0 4 - 5 5 5 - 1 2 1 2 TOTAL12

# 8 3. Press the edit flash button to edit the name, and the cursor will blink over the first character. DIR MICHAEL BROW 6 0 4 5 5 5 1 2 1 2 TOTAL12

# 8 cursor is blinking 4. Press the SCROLLLEFT or RIGHT button to move the cursor to the letter or number you want to change. To erase, press the delete scan button. To add, use the TELEPHONE KEYPAD

wxyz 9 buttons. (See page 31 for details.) 5. Press the SCROLL UP or DOWN button to edit the number. 21 Caller ID System Operation 6. Press the SCROLLLEFT or RIGHT button to move the cursor to the number you want to change. To erase, press the delete scan button. To add, use the TELEPHONE KEYPAD

wxyz 9 buttons. (See page 31 for details.) DIR MICHAELBROW 6 0 4 5 5 5 1 2 1 2 TOTAL12

# 8 6 cursor is blinking 7. Press and hold down the redial save/pause button to confirm. IMPORTANT:

It is not advisable to save a telephone number without the corresponding name in the DIRECTORY. This will lead to improper displays on PRIVATE and OUT OF AREA calls. NOTE: When no active buttons are pressed for 20 seconds, the LCD Screen will automatically return to STANDBY mode. Editing the Number in the DIRECTORY before Dialing 1. Press the button. 2. Press the SCROLL UP or DOWN button to find the caller. 3. Press the edit flash button to edit the name. 4. Press the SCROLL DOWN button. e.g. DIR MICHAELBROW 6 0 4 5 5 5 1 2 1 2 TOTAL12

# 1 6 cursor is blinking 5. Press the SCROLLLEFT or RIGHT button to move the cursor to the number you want to change. To erase, press the delete scan button. To add, use the TELEPHONE KEYPAD

wxyz 9 buttons.

*7 6. Press and hold down the DIAL 7 button for a local call, or press and hold down the DIAL 10 button for a local call with area code, or press and hold down the DIAL1+

#1+

button for a long distance call. 7. To end your conversation, either press the talk button or place the HANDSET on the BASE UNIT. 22 Caller ID System Operation NOTE:

If you want to save the edited number in the DIRECTORY, follow steps 1 through 5 and then press and hold down the redial save/pause button. Placing Calls from the DIRECTORY 1. Press the button. 2. Press the SCROLL UP or DOWN button to find the record you want to call.

*7 3. Press and hold down the DIAL 7 button for a local call, or press and hold down the DIAL 10 button for a local call with area code, or press and hold down the DIAL 1+

#1+

button for a long distance call. 4. To end the call, either press the talk button or place the HANDSET on the BASE UNIT. Deleting All Records in the DIRECTORY 1. Press the button. 2. Press and hold down the delete scan button for at least 3 seconds while in DIRECTORY mode. ALL DELETE 10:00AM 8/24 TOTAL0 3. Press the button to return to STANDBY mode. Selective Deleting in the DIRECTORY 1. Press the button. 2. Press the SCROLLUP or DOWN button to find the record you want to delete. 3. Press and hold down the delete scan button for at least 3 seconds, then the LCD Screen will display the next record in the DIRECTORY. DELETE

# 5 TOTAL 12 4. Press the button to return to STANDBY mode. 23 Caller ID System Operation Function Operation You can change the settings on the HANDSET through the functions menu. This unit contains the following special functions:

A. LANGUAGE B. SILENT ON/OFF C. TIME SET D. RINGER VOLUME E. LCD CONTRAST F. PBX NUMBER G. FLASH TIME H. PAUSE TIME I. VOICE MAIL J. MSG WAITING L. RESET K. HANDSET REGISTRATION To access, press the menu voice mail button at STANDBY mode, then press the TELEPHONE KEYPAD button.

wxyz 9

*7

, and

#1+

button or the SCROLLUP or DOWN ENGLISH SILENT TIME SET KEYPAD

#1 TOTAL12 1 Button OFF

#2 TOTAL12 10:00AM 8/24

#3 TOTAL12 KEYPAD abc 2 Button KEYPAD def 3 Button RING: HI CONTRAST PBX NO.

# 4 TOTAL12 5

#5 TOTAL12 OFF

#6 TOTAL12 KEYPAD ghi 4 Button KEYPAD jkl 5 Button KEYPAD mno 6 Button FLASH TIME 600

# 7 TOTAL12 PAUSE TIME 4

#8 TOTAL12 VOICE MAIL KEYPAD pqrs 7 Button KEYPAD tuv 8 Button KEYPAD EXT REG.

KEYPAD

*7 MSG WAITING OFF

# 10 TOTAL12

# 11 TOTAL12 RESET Button KEYPAD Button KEYPAD 24

#9 TOTAL12 wxyz 9 Button

# 12 TOTAL12

#1+

Button Caller ID System Operation A. Language This telephone offers English, Spanish, French, and Portuguese languages for your convenience. 1. Press the menu voice mail button. 2. Press the TELEPHONE KEYPAD 1 button. 3. Press the edit flash button. 4. Press the SCROLL UP button to select the language you desire. You can also set the language by pressing the following TELEPHONE KEYPAD buttons;

for Portuguese. for French, or for Spanish, for English, or DOWN abc 2 def 3 ghi 4 1 English is the preset language. 5. Press and hold down the redial save/pause button. 6. Press the menu voice mail button to return to STANDBY mode. B. Silent On/Off This telephone will generate the first ring sound even in the BLOCKED CALL mode to indicate that you have an incoming call. To keep the ringer silent in BLOCKED CALLmode, you can turn off the first ring sound. 1. Press the menu voice mail button. 2. Press the TELEPHONE KEYPAD abc 2 button. 3. Press the edit flash button. 4. Press the SCROLL UP or DOWN button to select the SILENT ON/OFF abc 2 for ON or 1 setting. You can also press the TELEPHONE KEYPAD buttons;

for OFF. SILENT OFF is the preset mode. 5. Press and hold down the redial save/pause button. 6. Press the menu voice mail button to return to STANDBY mode. C. Time Set Set the date and time. 1. Press the menu voice mail button. 2. Press the TELEPHONE KEYPAD def 3 button. edit flash 3. Press the 4. Use the TELEPHONE KEYPAD button to enter the month, date, hour, and minute. The cursor moves automatically after entering each item. Press the TELEPHONE KEYPAD button. for AM setting, or press the TELEPHONE KEYPAD abc 2 for PM setting. 1 25 Caller ID System Operation 5. Press and hold down the redial save/pause button. 6. Press the NOTE: The date and time will automatically set, if you have subscribed to the Caller ID button to return to STANDBY mode. voice mail menu service from your local telephone company. D. Ringer Volume This function enables you to adjust the ringer volume from HI, LOW, and OFF as desired. 1. Press the menu voice mail button. 2. Press the TELEPHONE KEYPAD ghi 4 button. 3. Press the edit flash button. 4. Press the SCROLLUP or DOWN button to adjust the ringer volume suitable for your convenience. You can also adjust the ringer volume by pressing the following TELEPHONE KEYPAD buttons;

for HI, abc 2 for LOW, or def 3 for OFF. HI is 1 the preset ringer volume. 5. Press and hold down the redial save/pause button. 6. Press the menu voice mail button to go back to STANDBY mode. E. LCD Contrast This unit enables you to select 8 brightness levels for the Large LCD Screen. 1. Press the menu voice mail button. 2. Press the TELEPHONE KEYPAD jkl 5 button. 3. Press the edit flash button. 4. Press the SCROLL UP or DOWN button to adjust the brightness of the LCD Screen. Level 5 is the preset brightness. 5. Press and hold down the redial save/pause button. 6. Press the menu voice mail button to go back to STANDBY mode. F. PBX Number This unit enables you to preset the PBX number (such as an 8 or 9) while you are using a switchboard system. 1. Press the menu voice mail button. 2. Press the TELEPHONE KEYPAD mno 6 button. 26 Caller ID System Operation 3. Press the edit flash button. 4. Press the SCROLL UP or DOWN button. (OFF is the preset PBX number.) PBX MODE OFF - set for direct line access. 5. Press and hold down the redial save/pause button. 6. Press the menu voice mail button to go back to STANDBY mode. NOTE: When placing a call by using the DIAL 7

, or the DIAL 10

, or the DIAL1+

pause time before the dialed telephone numbers.

#1+

button, this telephone will automatically add the PBX number and a

*7 G. Flash Time This unit enables you to select the standard FLASH TIME applicable to your calling area. If you are not sure of the FLASH TIME you are using, call your local telephone company. 1. Press the menu voice mail button. 2. Press the TELEPHONE KEYPAD pqrs 7 button. 3. Press the edit flash button. 4. Press the SCROLLUP or DOWN button to select the FLASH TIME. You can also set the FLASH TIME by entering the FLASH TIME number using the TELEPHONE KEYPAD

wxyz 9 buttons. The preset FLASH TIME is 600 milliseconds. 5. Press and hold down the redial save/pause button. 6. Press the menu voice mail button to go back to STANDBY mode. H. Pause Time This unit enables you to adjust the PAUSE TIME when placing a call using a switchboard system or dialing long distance calls. 1. Press the menu voice mail button. 2. Press the TELEPHONE KEYPAD tuv 8 button. 3. Press the edit flash button. 4. Press the SCROLL UP or DOWN button to adjust the pausing time. The preset pause time is 4 seconds. 5. Press and hold down the redial save/pause button. 6. Press the menu voice mail button to return to STANDBY mode. 27 Caller ID System Operation I. Voice Mail This telephone enables you to store the Voice Mail Access Code number in your area. This will automatically connect you to the Voice Mail service provider with one-touch dialing. 1. Press the menu voice mail button. 2. Press the TELEPHONE KEYPAD wxyz 9 button. 3. Press the edit flash button. 4. Enter the Voice Mail Post Code number by using the TELEPHONE KEYPAD

wxyz 9 buttons. 5. Press and hold down the redial save/pause button. 6. Press the menu voice mail button to go back to STANDBY mode. J. MSG Waiting (Message Waiting) To turn off the Message Waiting LCD Screen indicator. 1. Press the menu voice mail button. 2. Press the TELEPHONE KEYPAD button. 3. Press the edit flash button. 4. Press the SCROLL UP or DOWN button. 5. Press and hold down the redial save/pause button. 6. Press the menu voice mail button to go back to STANDBY mode. IMPORTANT: The Message Waiting LCD indicator will automatically turn ON, if you have subscribed to Voice Mail message service and if you have Visual Message Indication from your local telephone company. IMPORTANT In order to utilize the Caller ID feature, you must subscribe to Caller ID service from your local telephone company. 28 Caller ID System Operation K. Handset Registration The multiple-handset feature allows up to 90 handsets to link to the BASE UNIT. Each new HANDSET has to register into the BASE UNIT to get a 2-digit extension number from 10 to 99. 1. Press the menu voice mail button. 2. Press the TELEPHONE KEYPAD 3. The EXT REG will appear on the LCD Screen. button.

*7 4. Press the edit flash button. 5. Use the TELEPHONE KEYPAD

wxyz 9 buttons to enter the name of the extension phone user. 6. Press the SCROLL DOWN button. 7. Enter the 2-digit extension number by using the TELEPHONE KEYPAD

wxyz 9 buttons. 8. Press and hold down the redial save/pause button. 9. While the REGISTERING displaying on the LCD Screen, press and hold down the page button on the BASE unit. Release the page button until the EXT REG. appears on the LCD Screen. 10. Press the menu voice mail button to go back to STANDBY mode. IMPORTANT:

If the unit you purchased is a one-handset package, we suggest that you assign your new HANDSET with the extension number (10). If the unit you purchased is with two or more handsets, after charging the HANDSETS, you should do the registration to assign different extension number to each HANDSET. NOTE:

The ADDITIONAL HANDSET (HCB704) is available through:

U.S. Electronics Service Center 105 Madison Avenue New York, NY 10016 1-800-825-5208 Do the handset registration to assign a new extension number once you get the new ADDITIONAL HANDSETS. 29

Caller ID System Operation L. RESET When you feel there is interference while you use this telephone, you can reset your cordless telephone to factory pre-set value but gain a new security code for your telephone. The name and telephone number in the Caller List and Directory memory will not lose while doing this reset operation. 1. Press the menu voice mail button. 2. Press the TELEPHONE KEYPAD

#1+

button. 3. The RESET will appear on the LCD Screen. 4. Press the edit flash button. 5. The CONFIRM will appear on the LCD Screen. 6. Press and hold down the redial save/pause button to confirm the reset. The WAIT REG. will appear on the LCD Screen to ask you to register your HANDSET. 7. After registering your HANDSET, follow the Function Operation in page 25~28 to set the other function of the HANDSET. IMPORTANT: When you are a multiple HANDSET user, please ask the user of the other HANDSET to register his HANDSET again to set up a new link to BASE UNIT; otherwise, his HANDSET will not work properly. 30 Multiple Handsets Feature Telephone Keypad Characters buttons are used to enter characters when The TELEPHONE KEYPAD entering names. Press the appropriate TELEPHONE KEYPAD button to get the following characters. wxyz 9

KEYPAD BUTTONS CHARACTERS 1 2 3 4 5 6 7 8 9

0

SPACE & ( ) * . 1 A B C 2 D E F 3 G H I 4 J K L 5 M N O 6 P Q R S 7 T U V 8 W X Y Z 9

0

EXAMPLE:

If you want to enter the characters ACE on the HANDSET LCD Screen. 1. Press the button. 2. Press the edit flash button. 3. Press the TELEPHONE KEYPAD abc 2 button, A will be displayed. Press the SHIFT RIGHT below.). button to move the cursor to the right to enter the next character (See NOTES 4. Press the TELEPHONE KEYPAD 5. Press the TELEPHONE KEYPAD abc 2 def 3 button three times to display C. button two times to display E. NOTES:

1. To enter the next character, press the appropriate button. If, however, the next character is on the same button as the previous character, you will first need to press the SHIFT RIGHT button. Pressing the SHIFT RIGHT button a second time will produce a space. 2. If you want to change any character, you can go back to the incorrect character by pressing delete scan button. To delete the character inside the cursor

,press the the SHIFT LEFT button. 3. You can store a maximum of 15 characters on the letter icon. 4. You can store a maximum of 16 digits on the number icon. 31 Multiple Handsets Feature Multiple Handsets Feature After two or more HANDSETS are registered with a BASE unit, and different extension number is assigned to each HANDSET, you get the advanced multiple handset features. The following paragraphs tell you how to use these advanced features. How to Receive Calls When there is an incoming call, all HANDSETS will ring, and the name and telephone number of the caller will appear on the LCD Screen provided that you have subscribed to the Caller ID service. Any HANDSET can press the talk button to answer the call. How to Place Calls Press the Calls in page 12 for the number dialing. talk button on any HANDSET to get a dial tone, and then follow the Placing NOTE:

If the line is used by other HANDSET, LINE IN USE will be displayed. Privacy Feature While a HANDSET is talking over the line, the other HANDSETS can not connected to their button on his own HANDSET. Meanwhile the other conversation by pressing the HANDSETS can not make a call at this moment, but the other HANDSETS can make intercom call to each other. talk Handset to Handset Intercom Call You can make an intercom call to any HANDSET which is registered to the same BASE unit. 1. Press the intercom button. The EXT NO. and - -

appear on LCD Screen for you to enter the desired 2-

digit extension number. 2. The called HANDSET rings. If the called HANDSET is in use, you will hear the busy tone, and HS - - IN USE will be displayed. HS12 IN USE the called handset (ext no.=12) is in use 3. The user of the called HANDSET can press his talk button to answer the intercom call. 4. Before the called HANDSET answers you call, you can press the intercom operation. intercom button again to cancel your 5. When you finish with the intercom call, press the talk button. 32 Multiple Handsets Feature Transfer a Call to Other Extension Handset While you are talking over the line, you can transfer the talking (far-end) party to the other HANDSET user. Transfer the call to a HANDSET without notify:

1. Press the intercom button. The line is put on hold, and your HANDSET displays EXT NO. and - -

appear on LCD Screen for you to enter the 2-digit extension number you want to transfer the call. 2. The called HANDSET will ring. Press the button on your HANDSET. The call is transfered, and you own HANDSET goes to Stand-By. talk 3. The user of called HANDSET can press the talk button on his HANDSET to answer the transfered call. 4. If the called H A N D S E T user did not answer the transferred call within 30 seconds, Your HANDSET will ring alarming you to receive the returned call. You can press the party. talk button to get back with the talking Transfer the call to a HANDSET with notify:

1. Press the intercom button. The line is put on hold, and your HANDSET displays EXT NO. and - -

appear on LCD Screen for you to enter the 2-digit extension number you want to transfer the call. 2. The called HANDSET will ring. 3. Converse with the user of the called HANDSET When he press the talk button on his HANDSET to answer. 4. Press the talk the call transfer. button on your HANDSET to complete 33 Answering System Operation Resetting the Answering System After connecting your phone, press and hold down the button for at least 3 seconds. Release the button and the unit will beep. Your unit will now reset itself. Then your unit will announce, Please enter new time and record your announcement. You can now set the day/time and record your new announcement. See the details in following paragraphs. stop NOTE:

In the use of this Answering System, if the machine freezes or acts abnormally, unplug and plug the AC adapter. Then follow the same procedure to re-initiate your Answering System. Setting the Day/Time Stamp Press and hold down the enter new time. Then enter the current day and time. 1. Day Setting set button until you hear the announcement Time is off, please Press and hold down the announced. 2. Hour Setting Press and hold down the announced. 3. Minute Setting Press and hold down the announced. day button. Release the button when the desired day is hour button. Release the button when the desired hour is min button. Release the button when the desired minute is Press the set button to confirm the selected day and time. The system will announce the day and time. You must set the Day and Time in order to have correct Day/Time stamp at the end of each incoming message. Anytime you have a power failure or power interruption, you must set the Day and Time again. 34 Answering System Operation Recording Your Outgoing Messages Your Answering System provides one PRIMARY MAILBOX and four individual MAILBOXES (1, 2, 3, 4) which can receive their own Incoming Messages (ICM). Before using your Answering System, it is suggested that you record an Outgoing Message (OGM). This is the announcement callers will hear when the system answers a call. A pre-recorded system announcement Please record your message after the beep is available if you choose not to record your own OGM. A. Recording your OGM in the PRIMARY MAILBOX 1. Press and hold down the ogm button to record your message. 2. Begin speaking immediately after you hear, Please record your announcement after the beep. Continue to depress the ogm button. One second after completing your OGM, release the ogm button. Your recorded message will be played after releasing the ogm button. NOTE: Your OGM must be at least 3 seconds and no more than 30 seconds in length. If you wish to change your OGM, repeat steps 1 through 2. After an OGM is recorded, you can do as below to use the pre-recorded announcement for your Answering System. 1. Press the 2. ogm button, while the OGM is playing, press the erase button. You have no announcement will be playing. Now the pre-recorded announcement Please record your message after the beep is used for your system. NOTE: To obtain a better sound quality for locally recorded (OGMs and Memos) messages, speak directly into the MICROPHONE from a distance of 9 to 12 inches. It is recommended that you record an OGM on your PRIMARY MAILBOX instructing a caller to leave an ICM in one of the four mailboxes. If the caller is using a Touchtone telephone, this will enable the caller to record an ICM directly into one of the four mailboxes by dialing 11 for MAILBOX 1, 22 for MAILBOX 2, 33 for MAILBOX 3, 44 for MAILBOX 4. Example of a Primary OGM: Hello, please leave a message after the tone, or if you are using 35 Answering System Operation a Touchtone telephone, please Dial 11 for Beth, Dial 22 for Jenny, Dial 33 for Jonathan, Dial 44 for Esson. NOTE: To check your OGM, press the ogm button. If you did not record an OGM, your Answering System will announce, You have no announcement. B. Recording your OGM to Individual MAILBOX 1, 2, 3 or 4 1. Press a mailbox button, the corresponding MAILBOX LED indicator will blink. 2. Press and hold down the 3. Begin speaking immediately after you hear, Please record your announcement after the button to record your message. ogm beep. Continue to press the ogm button. One second after completing your OGM, release the ogm button. Your recorded message will be played after releasing the ogm button. NOTE: Your OGM must be at least 3 seconds and no more than 30 seconds in length. If you wish to change your OGM, repeat steps 1 through 3. NOTE: To check your OGM in a mailbox, press a mailbox button and then press the ogm button. If you do not have an OGM in a mailbox, it will announce MAILBOX#, you have no announcement. Once a mailbox is activated, its corresponding MAILBOX LED indicator blinks slowly to show that the mailbox is active. If you do not press a button to activate another function within 12 seconds, the Answering System will return to the PRIMARY MAILBOX. You may return to the PRIMARY MAILBOX at anytime by pressing the stop button. Adjusting the Speaker Volume While the Answering System plays back your message, the speaker volume can be adjusted by pressing the volume level:

vol +

and vol -

button. The LED Message Display will display the selected 0 - Speaker off 1~8 - Volume from low to high Turning the Answering System ON/OFF 1. Press the button to turn ON the Answering System. You will hear the following message, Answering machine is ON. 2. Press the button again to turn OFF the Answering System. You will now hear the following message, Answering machine is OFF. NOTE: Once turned OFF, the Answer function will answer only on the tenth ring, allowing you to turn the Answering System ON from a remote location. 36 Answering System Operation Setting to Answer Calls The ANSWER ON/OFF LED indicator must be ON for the Answering System to answer calls. Depending on the setting of the ANNC/ICM switch, the Answering System will either hang up after your announcement (ANNC) or begin to record your callers messages (ICM). After the caller leaves an ICM, the time and day will be stamped at the end of each recorded ICM. The ICM is stored in the MEMORY and the LED Message Display shows the total number of ICMs currently stored. NOTE:

ICMs are limited to a maximum of 2 minutes. If the ICM is more than 2 minutes, the system beeps twice and hangs up; or if the Answering Systems memory runs out, the Answering System announces, Memory full, and hangs up. Setting to Announce Only During ANNC (Announce) mode, your system answers incoming calls with your recorded announcement but will not record any ICMs. 1. Set the ANNC/ICM select switch to ANNC. 2. Press and hold down the button to record your announcement. ogm 3. Begin speaking after you hear, Please record your announcement after the beep. Do not release the ogm button until you have completed your announcement OGM. NOTE: Your OGM must be at least 3 seconds and no more than 30 seconds in length. 4. Release the ogm button one second after your announcement is completed, and the LED Message Display will show AO . NOTE:

If you have not recorded an announcement for ANNC mode, even if the switch is set to ANNC mode, the Answering System will automatically operate in ICM mode and will record all ICMs. talk Screening Incoming Calls The Answering System allows you to listen to a caller leaving an ICM. Once the Answering System starts answering a call, press the button (or pick up any extension telephone on the same line), the Answering System will stop recording and you may converse with your caller. Message Alert When the message alert switch is ON, the unit will generate a beep sound every 15 seconds after a new message has been recorded. If you do not want to hear the beep, set the switch to the OFF position. Setting Ring Select To choose the number of times the phone rings before the Answering System responds, set the Ring Select switch to 3R, 5R, or TS (TOLL SAVER). Set to 3R -System answers call after the third ring. Set to 5R -System answers call after the fifth ring. Set to TS - Use TOLL SAVER (TS) when you will be checking your system for messages from a remote location using long distance services or from a pay phone. The Answering System responds on the third ring only if you have a new message waiting. If there are no new messages, the phone will answer after the fifth ring. You can hang up on the fourth ring to avoid paying for the call. 37 Answering System Operation Recording a Memo A. To record a Memo in the PRIMARY MAILBOX 1. Press and hold down the 2. Begin speaking immediately after you hear, Please record your message after the beep. button to record your Memo. memo Continue to depress the memo button. One second after completing your Memo, release the memo button. Day and time are automatically stamped at the end of the message. NOTE: The Answering System advances the message count automatically after the actual message is recorded. B. To record a Memo in an individual MAILBOX (1, 2, 3, 4) 1. Press a mailbox button, the corresponding MAILBOX LED indicator will blink. 2. Press and hold down the 3. Begin speaking immediately after you hear, Please record your message after the beep. button to record your Memo. memo Continue to depress the memo button. One second after completing your Memo, release the memo button. Day and time are automatically stamped at the end of the message. NOTE: The Answering System advances the message count automatically after the actual message is recorded. NOTE: To obtain a better sound quality for locally recorded (OGMs and Memos) messages, speak directly into the MICROPHONE from a distance of 9 to 12 inches. Playing of Messages/Memos A. To play messages/memos in the PRIMARY MAILBOX 1. Press the play button, the system will play all NEW messages/memos. 2. After playing all NEW messages/memos, press the play button again, the system will play all of its messages. 38 Answering System Operation B. To play messages/memos in an individual MAILBOX (1, 2, 3, 4) 1. Press a mailbox button, the corresponding MAILBOX LED indicator starts to blink. 2. Press the play button. The system will play all NEW messages/memos. 3. After playing all NEW messages/memos, press the play button again, the system will play all of its messages/memos. NOTE: When the MAILBOX LED indicators are lit, messages are present. C. To interrupt a message 1. Press the displayed. stop button once to pause a message while it is being played, PA will be 2. Press the play button to continue playing the current message. 3. Press the stop button twice to end the playing of a message. D. To repeat a message/memo 1. Press the rpt button while playing a message. The system repeats the current message in its entirety. E. To skip message/memo 1. Press the button once. The Answering System stops playing, moves to the next message/memo and resumes playback. The system advances one message/memo each skip time you press the skip button. Saving Messages The Answering System saves your messages automatically. After playing all of your messages, the Answering System announces, End of messages and the total number of messages stored in the memory will be indicated on the LED Message Display. 39 Answering System Operation Erasing Messages A. To erase all of the messages in the PRIMARY MAILBOX 1. Press and hold down the button until you hear the announcement, Messages erased, you have no messages. If you have a new message in the PRIMARY MAILBOX, you will hear, You have # new messages. erase B. To erase all of the messages in an individual MAILBOX (1, 2, 3, 4) 1. If you want to erase all of the messages in a mailbox, activate the desired mailbox. 2. Press and hold down the button until you hear the announcement, Mailbox #, messages erased. You have no messages. If you have a new message in the MAILBOX #, you will hear, You have # new messages. erase C. To erase selected messages/memos 1. While the unwanted message is playing, press the button. The Answering System announces erasure of the selected message/memo, and the LED Message Display shows the symbol of Ea. After the erasure is complete, the numeric order of the remaining messages will be rearranged. erase When the Memory is Full When there is no memory available for additional messages, the Answering System will announce, Memory full, but will not save any new messages. NOTE: When the Answering System memory is full, previously reviewed messages must be deleted so that the system can record new messages. NOTE: You must enter your Remote Access Code within 10 seconds of activating the Remote Control function to maintain your connection with the Answering System. (Refer to Remote Control Operation on page 41.) Two -Way Recording Two-way recording allows you to record your conversation with another caller. In order to have 2-way recording, you must use the cordless HANDSET of the Answering Machine during recording time. 1. During conversation, press a mailbox button (MAILBOX 1, 2, 3, or 4) where you want to record your conversation. The corresponding MAILBOX LED indicator will blink. 2. Press and hold down the memo button. The LED Message Display will show to indicate the RECORDING mode. memo button to end your conversation recording. 3. Release the 4. Also you can record on the PRIMARY MAILBOX, just follow steps 2 and 3. NOTE: Recording two-way conversations may be subject to local, state or federal laws and regulations. Consent of both parties is required when a conversation will be recoreded. 40 Remote Control Operation Remote Operation through a Tone Telephone You can use many Answering System features when you are away from home. To protect your privacy, most of the features can be used only after you enter the three-digit Remote Access Code. Remote Access Codes The Remote Access Codes are preset at the factory as below. You can use the preset codes or choose your own. PRIMARY MAILBOX:

MAILBOX 1:

MAILBOX 2:

MAILBOX 3:

MAILBOX 4:

999 555 666 777 888 NOTE:

If there is a power failure of the BASE UNIT, the Remote Access Codes return to the factor preset codes. Changing of the Remote Access Codes All of the digits of the Remote Access Codes are a combination of the numbers 5, 6, 7, 8, 9, and 0. IMPORTANT: Digits 1, 2, 3, and 4 cannot be used when changing the Remote Access Codes for any mailbox (including the PRIMARY MAILBOX). 1. Press a mailbox button for MAILBOX 1, 2, 3, or 4. For the PRIMARY MAILBOX, follow steps 2 to 6. 2. Press and hold down the code button until you hear the announcement, Please enter new password. 3. Press and hold down the day button. Release the button when you hear the desired first digit of the code. 4. Press and hold down the second digit of the code. hour button. Release the button when you hear the desired 5. Press and hold down the min button. Release the button when you hear the desired third digit of the code. 6. Press the code button, the 3-digits you have selected will be announced. 7. If your new Remote Access Code is the same as that of another mailbox, the Answering System will not record your password and will announce, Please try again. 41 Remote Control Operation Using the Remote Instruction Code 1. Dial your telephone number. 2. Listen to or bypass the OGM in the PRIMARY MAILBOX by entering your Remote Access Code. 3. A beep will sound when your Remote Access Code is correctly accepted by your Answering System. If the announcement does not stop, enter the Remote Access Code again. 4. 5. The Answering System will request that you enter the Instruction Code or press 0 for help. A. If you do not know the Instruction Code, press the 0 button immediately. The Answering System will announce the Instruction Codes. Otherwise, if a command is not received by the Answering System within 10 seconds, it will signal 3 beeps and hang up. The following is the Remote Instruction Code Help Menu:

Instruction Codes To playback announcement press 5. To record memo press 6. (Press 0 for PRIMARY MAILBOX, Press 1 for MAILBOX 1, Press 2 for MAILBOX 2, Press 3. for MAILBOX 3, and Press 4. for MAILBOX 4.) To record announcement press 7. To turn answering machine OFF or ON press 8. To change mailbox press

(star).

To playback message press 2. While message playback:

To repeat message press 1. To skip message press 3. To stop press 4. To erase message press 9. B. Press the corresponding number of the Instruction Code you wish to activate. You do not have to listen to the entire Instruction Code Help Menu before giving a command. You may enter the desired Instruction Code Number at any given time. C. After accessing the Answering System, you must enter the next command within 10 seconds after the end of each operation. Otherwise, your Answering System will hang up the phone automatically. 42 Security Security System Your cordless telephone uses a digital coding security system to prevent unauthorized use of your telephone line by another nearby cordless telephone. The system has its own identifying signal created by microcomputers in both the BASE UNIT and the HANDSET. Security Code This telephone has an internal security code with 65,536 possible combinations. After doing the HANDSET registration, the security code is stored in the non-volatile memory of HANDSET and BASE UNIT; therefore, the security code will not be lost caused by:

1. A power failure on the BASE UNIT. The communication between the HANDSET to the BASE UNIT, or HANDSET to HANDSET will be linked right after the power comes in. 2. After replacing the HANDSET BATTERY PACK. The HANDSET can be used right after the BATTERY PACK replaced. Multi-Channel Access Your cordless telephone lets you select a channel from the 40 frequencies available to transmit signals between the BASE UNIT and HANDSET. When you notice interference from other cordless telephones, change to another channel by pressing the HANDSET. delete scan button on the 43 Recharging the BATTERY PACK Battery Type Use the following type and size of BATTERY PACK:

Cordless Telephone BATTERY PACK 3.6V, 750mAh U.S. Electronics Inc. Ni-MH Battery Pack: model B660 This BATTERY PACK is available through:

U.S. Electronics Service Center 105 Madison Avenue New York, NY 10016 1-800-825-5208 NOTE:

1. During a power interruption, the BASE UNIT does not operate, and a phone conversation cannot be made on the HANDSET. Recharging the Battery Pack The nickel metal hydride (Ni-MH) BATTERY PACK in the HANDSET can be recharged many times using the built-in charger in the BASE UNIT. When the BATT LOW symbol appears on the LCD Screen, a beep sound will be heard every 10 seconds. This indicates that the BATTERY PACK needs to be recharged. Charge the BATTERY PACK at least once every 90 days of non-use to avoid battery failure. When the BATTERY PACK can no longer be charged, replacement of the BATTERY PACK will be necessary. The BATTERY PACK used in your telephone may develop a condition known as MEMORY. Once subjected to a regular short discharging routine, the BATTERY PACK assumes the discharging pattern it was subjected to. This is known as a MEMORY condition which causes rapid discharging thereby shortening the BATTERY PACK charge span. If you believe your BATTERY PACK has developed a MEMORY condition, do not charge the HANDSET until the BATT LOW symbol appears on the LCD Screen. When the BATT LOW symbol appears on the LCD Screen, charge the HANDSET fully for 12 hours. IMPORTANT In order to get maximum life from the HANDSET BATTERY PACK, be sure to charge the HANDSET for 12 hours before initial use. 44 Changing the BATTERY PACK Changing the Battery Pack The BATTERY PACK provides power for the HANDSET of your cordless telephone. To Replace BATTERY PACK:

1. Remove the HANDSET BATTERY COMPARTMENT COVER by sliding it down. 2. Pull out the BATTERY PACK PLUG and remove the BATTERY PACK. 3. Plug the new BATTERY PACK into the BATTERY CONNECTOR. 4. Slide the HANDSET BATTERY COMPARTMENT COVER firmly into place in its closed position. 5. Before use, charge the new BATTERY PACK for 12 hours. ATTENTION:

The telephone that you have purchased contains a rechargeable BATTERY PACK. The BATTERY PACK is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this BATTERY PACK into the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal. 1. Remove the BELT CLIP. 2. Slide up the LOCK TAB. 3. Pull out the HANDSETS BATTERY COMPARTMENT COVER. IMPORTANT In order to get maximum life from the HANDSET BATTERY PACK, be sure to charge the HANDSET for 12 hours before initial use. 45 Problem Solving Problem Solving Section For your assistance, we have listed below a few common problems. Phone does not work, check the following:

1. BASE UNIT is plugged into a power source. 2. HANDSET is charged. 3. TONE/PULSE Select switch is in the right position. 4. TELEPHONE LINE CORD is plugged into the TELEPHONE JACK. Range of phone limited, check the following:

1. BASE UNIT is centrally located in your residence. 2. BASE UNIT is not located near appliances. No dial tone, check the following:

1. TELEPHONE LINE CORD plugs are connected to the TELEPHONE JACK and TELEPHONE LINE CONNECTION JACK. 2. BASE UNIT is plugged into a power source. Received signal flutters or fades, check the following:

1. BATTERY PACK in the HANDSET is fully charged. 2. HANDSET is not too far from the BASE UNIT. Interference on reception, check the following:

1. Noise may be picked up from electrical products in the home or electrical storms. Generally, this noise is a minor annoyance and should not be interpreted as a defect in your system.

(See Technical Information on page 48.) 2. Choose an alternate channel using the 3. Do not use this telephone within 20 ft. of a microwave oven while it is working, as you may experience interference. This is a normal occurrence with 2.4 GHz phones and should not be interpreted as a defect in the product. button on the HANDSET. delete scan Long Distance L-D-C indicator is not ON when receiving a long distance call, check the following:

1. Your local telephone company can provide the Area Code on an incoming long distance call. Excess static, check the following:

1. Check to see that the ANTENNA is not touching another metal object. If after pressing the following:

1. BASE UNIT is plugged into a power source. talk button, you receive three beeps and no dial tone, check the 46 Problem Solving Answering System does not work, check the following:

1. BASE UNIT is plugged into a power source. Answering System does not answer calls, check the following:

1. ANSWER ON/OFF LED indicator is lit. Answers calls only after 10 rings, check the following:

1. ANSWER ON/OFF LED indicator is lit. 2. Message Memory is not full. Does not respond to remote commands, ensure the following:

1. Correct Remote Access Code is entered. 2. A T ONE telephone is being used. Message are incomplete, ensure the following:

1. Message Memory is not full. 2. Caller may be hesitating and pausing for more than 7 seconds. Answer calls but not record messages, check the following:

1. ANNC/ICM switch is set to ICM. 2. Memory is not full. 3. Extension telephone was not picked up. Answering System announce Time is off at the end of each message, check the following:

1. Have you set the Day/Time?

2. Was there a power interruption?

No Sounds on the BASE UNIT:

1. Adjust the volume by using vol +

and vol -

button and make sure the volume level is not 0. Reset your cordless telephone:

1. You can reset your unit if the unit is not working properly. Unplug and then plug the AC ADAPTER into its power source then press and hold down the button for at least 3 seconds, then release the button and the unit will beep. (See detail operations in page 34.) stop NOTE:

If none of telephones in the house are working, disconnect one set at a time to verify that none of the phones are causing the problem. If you still have a problem after doing this, and your telephone still does not work, please contact your local phone company. 47 Technical Information Technical Information This cordless telephone uses radio frequencies to allow mobility. There are certain difficulties in using radio frequencies with a cordless telephone. While these are normal, the following could affect the operation of your system. Noise Electrical pulse noise is present in most homes at one time or another. This noise is most intense during electrical storms. Certain kinds of electrical equipment such as light dimmers, fluorescent bulbs, motors, and fans also generate noise pulses. Because radio frequencies are susceptible to these noise pulses, you may occasionally hear them in your HANDSET. Generally they are a minor annoyance and should not be interpreted as a defect in your system. Range Because radio frequency is used, the location of the BASE UNIT can affect the operating range. Try several locations in your home or office and pick the one that gives you the clearest signal to the HANDSET. Interference Electronic circuits activate a relay to connect the cordless telephone to your telephone line. These electronic circuits operate in the radio frequency spectrum. While several protection circuits are used to prevent unwanted signals, there may be periods when these unwanted signals enter the BASE UNIT. You may hear clicks or hear the relay activate while you are not using the HANDSET. If the interference occurs frequently, it can be minimized or eliminated by relocating the BASE UNIT.You can check for interference before selecting the final BASE UNIT location by plugging in the telephone. NOTICE:

This cordless telephone uses radio communication between the HANDSET and the BASE UNIT and may not ensure privacy of communication. Other devices, including another cordless telephone, may interfere with the operation of this cordless telephone or cause noise during operation. Units not containing coded access may be accessed by other radio communication systems. Cordless telephones must not cause interference to any licensed radio service. IMPORTANT When you hear interference, press the button to change the operating delete scan channel. 48 FCC Requirements Federal Communications Commission Requirements This equipment complies with Part 68 of the FCC rules. A label on the BASE UNIT of the equipment contains, among other information, the ACTA Product Number and the Ringer Equivalence Number (REN) for this equipment. You must, upon request, provide this information to your telephone company. The REN is also useful in determining the number of devices that you may connect to your telephone line and still allow all of these devices to ring when your telephone number is called. In most, but not all areas, the sum of the RENs of all devices connected to one line should not exceed five (5.0). To be certain of the number of devices that you may connect to your line, contact your local telephone company. If your equipment should cause harm to the telephone network, the telephone company may temporarily disconnect your service. If possible, they will notify you in advance that temporary discontinuance of service may be required. However, when advance written notice is not possible, the telephone company may temporarily discontinue service without notice if such action is necessary under the circumstances. The telephone company may make changes in its communication facilities, equipment, operations, or procedures where such action is reasonably required in the operation of its business and is not inconsistent with the rules and regulations of the Federal Communications Commission. Do not attempt to repair or modify this equipment. Warning: Changes or modifications not expressly approved by the party responsible for its compliance could void the user s authority to operate the equipment. Some cordless telephones operate at frequencies that may cause interference to nearby TVs and VCRs. To minimize or prevent such interference, the BASE UNIT of the cordless telephone should not be placed on or near a TV or VCR. If interference is experienced, moving the cordless telephone farther away from the TV or VCR will often reduce or eliminate the interference. This equipment should not be used on coin telephone lines. Connection to party line service is subject to state tariffs. If trouble is experienced, disconnect this equipment from the telephone line to determine if it is causing the malfunction. If the equipment is determined to be malfunctioning, its use should be discontinued until the problem has been corrected. IMPORTANT Placing your BASE UNIT near appliances such as televisions, refrigerators, radios, or microwave ovens may cause interference. 49

FCC Requirements Federal Communications Commission Requirements (continued) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving ANTENNA.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is Increase the distance between the equipment and the receiver. connected.

- Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subjected to the following two conditions:

(1)

(2) this device may not cause harmful interference, and this device must accept any interference received including interference that may cause undesired operation. The equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment, under 47 CFR2.1093 paragraph (d)(2). The 2.4GHz DSST Multi Handset with CID + DAM has been tested to the FCC exposure requirements (Specific Absorption Rate). 50 Warranty Warranty Information BellSouth Products One-Year Limited Warranty This limited warranty sets forth all BellSouth Products responsibilities regarding your telephone. There are no other expressed or implied warranties from BellSouth Products. Warranty Service Provided If you purchased the telephone new from a retail vendor, BellSouth Products warrants the telephone against defects in material and workmanship for a period of one (1) year from the original date of purchase. This warranty is in lieu of all other express warranties. This warranty begins when you purchase the telephone and continues for one (1) year unless you sell or rent the telephone, in which case the warranty stops. BellSouth Products disclaims any implied warranty, including the warranty of merchantability and the warranty of fitness for a particular purpose, as of the date of 90 days from your original purchase of the telephone. BellSouth Products assumes no responsibility for any special, incidental, or consequential damages. This warranty gives you specific legal rights and you may have other rights which vary from state to state. Some states do not allow the exclusion or limitations of special, incidental or consequential damages, or limitations on how long a warranty lasts, so the above exclusion and limitation may not apply to you. Warranty Service Not Provided This warranty does not cover damage resulting from accident, misuse, abuse, improper installation or operation, lack of reasonable care, unauthorized modification, or the affixing of any attachment not provided by BellSouth Products with the telephone, and/or loss of parts. This warranty is voided in the event any unauthorized person opens, alters or repairs the telephone. All BellSouth equipment being returned for repair must be suitably packaged. Telephone companies use different types of equipment and offer various types of services to customers. BellSouth Products does not warrant that this telephone is compatible with the type of equipment of any particular telephone company or the services provided by it. 51 Warranty What To Do for Warranty Service During the first thirty (30) days, a defective product is eligible for over-the-counter exchange at the retailer from whom it was purchased. After thirty (30) days, the defective product should be returned to the authorized service center. Please allow 2-3 weeks for the return of your telephone product. The shipping address of the authorized service center is:

U.S. Electronics Consumer Center C/O Southern Bonded Warehouse 7137 Southlake Parkway Morrow, GA30260 NOTE: A telephone product received which was not made for BellSouth Products or which is not defective as determined by our test procedures will not be repaired and will be returned to you C.O.D., freight collect. To Obtain Warranty Service Provide proof of the date of purchase within the package. Prepay all shipping costs to the authorized service center. Include a return shipping address within the package. Please retain your sales receipt, the carton, the packing materials, and the printed material. The original carton is the best shipping container for the telephone should you have to return it. For your reference:

Serial Number Date of Purchase Name of Dealer Customer Service Telephone Number:

1-800-210-8950 OUTSIDE THE U.S.A. CALL 1-212-242-6978 Visit Us on the Web:

www.uselectronics.info 52 Wall Mounting Template This page serves as a template for attachment of screws to the wall when mounting this telephone on the wall. 1. Cut out this page. 2. Use this template to determine the distance between screws when mounting this phone on the wall. The two cross hairs identify where to attach the screws. 53 IMPORTANT In order to get maximum life from the HANDSET BATTERY PACK, be sure to charge the HANDSET for 12 hours before initial use. IMPORTANT Placing your BASE UNIT near appliances such as televisions, refrigerators, radios, or microwave ovens may cause interference. IMPORTANT When you hear interference, press the button to change the operating delete scan channel. IMPORTANT The AC ADAPTER must always be plugged into an electrical outlet. IMPORTANT If you live in an area which gets frequent thunderstorms, we strongly recommend plugging your AC ADAPTER into a surge protector. IMPORTANT In order to utilize the Caller ID feature, you must subscribe to Caller ID service from your local telephone company. 54 STOP Make certain you receive the best performance from your telephone. Read this manual first. Visit Us on the Web:

www.uselectronics.info Made in China CM Special Features Congratulations on your selection of a quality BellSouth product. With proper care, and by following the set-up and user instructions in this Owner s Manual, this unit will provide you with years of trouble-free service. BellSouth is committed to providing quality products that fit your needs. We would like to have any comments or suggestions you might have on this product. You may mail your comments to:

U.S. Electronics 105 Madison Avenue New York, NY 10016 When examining your new BellSouth cordless telephone, you will find an array of special features including:

Digital Spread Spectrum Technology Multiple-Handset Feature - Capable of supporting up to a maximum of 90 handsets. Filtered SoundT M S y s t e m - Gets considerably less noise than conventional cordless telephones because of a special circuit which delivers the clearest possible reception. 54 Channel Auto Scan - Press the clearest channel for any call. delete scan button on the HANDSET to find and lock on to the Desk or Wall Mount - Use this equipment as a desk phone or as a wall phone. TONE or PULSE Dialing - Use this phone for either TONE (push-button) or PULSE (rotary) dialing. Automated Functions - Redial the last number called and automatic STANDBY mode. Security - Ensures greater privacy because a built-in security code with 65,536 combinations prevents use of your telephone line by another nearby cordless phone. Dependable Battery - Recharge your BATTERY PACK many times with the built-in charger. The battery low warning tone tells you when the BATTERY PACK needs recharging. (See page 44.) Special Services - Use the edit flash button to access special services such as Call Waiting supplied by your telephone company or company switchboard. STANDBY Mode - When in STANDBYmode (ON-HOOK), the phone is capable of receiving a call. When the HANDSET is on the BASE UNIT, it is automatically in the STANDBY mode

(ON-HOOK). When the HANDSET is taken off the BASE UNIT, it remains in the STANDBY mode until you activate the talk button. Battery Power Saver - Once fully charged, in STANDBY mode, the HANDSET can receive/send calls for a maximum of five days without the need for recharging. Length of charge depends on frequency of use. Luminous LCD Screen - The LCD Screen emits light for 5 seconds every time you press any of the buttons on the HANDSET. HANDSET Ringer Level - Select the ringer volume level (HI, LOW, OFF). HANDSET VOLUME CONTROL Switch - Select the receiver volume level (HI, MID, LOW). HEADSET JACK - Your telephone can utilize a headset for hands-free communication. BELT CLIP - Use the BELT CLIP to hang your HANDSET on your belt. Special Features CALLER ID SYSTEM Multi-Function Large LCD Screen - Shows the number you are dialing, and with Caller ID service (available through subscription from your local telephone company), displays information about the caller before you answer the call. Name and Number DIRECTORY - Stores up to 40 names and numbers so that you can call them with a single key stroke. Caller List - Available with Caller ID service. Stores up to 80 calls to keep track of everyone who called. The name, phone number, time, and date of the call are recorded. Allows you to return their calls with a single key stroke. Preferred Calls - You can mark the name and number of a welcome caller in the DIRECTORY. When that number calls in, the callers name will appear on the LCD Screen and a special ring sound will be heard. Blocked Calls - You can mark the name and number of an unwelcome caller in the DIRECTORY. When that number calls in, the callers name will appear on the LCD Screen and the ringer will be disabled. Repeat Call Indicator - Shows if a new incoming call has called more than once. Out of Area Call Indicator - Advises you that the incoming call is not in a Caller ID service area, or does not support the Caller ID system. Private Call Indicator - Advises you that the callers name and/or telephone number of the incoming call is blocked by the system. Call Waiting Service - Displays the name and number of the second caller, if you have subscribed to call waiting service from your local telephone company (See page 17). Voice Mail - Indicates message waiting signal if you subscribed to Voice Mail message service and requested Visual Message Indication from your local telephone company (see page 17). This telephone also detects a Stutter Dial Tone signal every time there is a Voice Mail message for your Voice Mail message provider if you have subscribed to Voice Mail message service. ANSWERING SYSTEM FEATURES Fully Digital Answering System - Provides a full range of answering functions without using cassette tapes. Digital Memory - Allows recording of memos and messages. Two Digits LED Message Display - Indicates the number of messages, indicates the status of the system. Ring-Detection Selectable - Choose the number of times the telephone rings before the system answers. Voice Day/Time Stamp - Systems tells the day and time of each received message or recorded memo. Message Alert - The ability to generate a sound signal when new messages are recorded. Call Screening - The ability to intercept a call when the unit is recording an incoming message

(ICM). Mailboxes - Allows four separate individuals to receive their own incoming messages. Auto Disconnection - Will automatically stop answering when HANDSET of any phone on the same line is lifted. Fast Message Skip Function - Skips to the next message. Remote Control Capable - Can be accessed through an outside line (Tone telephone) via 3-

digit access code. BASE UNIT SPEAKERPHONE FEATURE HANDSET Controls 1. HANDSET ANTENNA 2. NEW CALL/MESSAGE WAITING INDICATOR Pg. 15 3. LCD SCREEN 4. SCROLLUP-DOWN

/SHIFT LEFT-RIGHT BUTTON Pg.16, 18~27, 29, 31 5. PHONE BOOK BUTTON Pg. 18~23, 31 6. REDIAL/PAUSE/SAVE BUTTON Pg. 15, 18~20, 22~23, 25~30 7. HEADSETJACK Pg. 14 8. DIAL10 BUTTON Pg. 14, 18, 22~23, 27 9. DIAL7/TEMPORARY TONE(*) BUTTON Pg. 14, 18, 21~23, 27 10. EDIT/FLASH BUTTON Pg. 17~18, 20~22, 25~31 11. TALK BUTTON Pg. 7, 8 12~15, 17~18, 22~23, 32~33, 37, 46 12. DELETE/SCAN BUTTON Pg. 18~19, 21~23, 31, 43, 46, 48, 54 13. MENU/VOICE MAIL BUTTON Pg. 17, 24~30 14. VOLUME CONTROL

(HI, MID, LOW) SWITCH 15. TELEPHONE KEYPAD Pg. 18, 20~22, 24~31 16. DIAL1+/# BUTTON Pg. 13, 17, 18, 20~22, 26 17. INTERCOM BUTTON Pg. 32~33 18. CHARGE CONTACTS HANDSET Controls 1. HANDSET ANTENNA 2. NEW CALL/MSG (MESSAGE) WAITING LED Indicator: Blinks when recording a new incoming call or when receiving a Message Waiting signal, if you have subscribed to a Voice Mail message service from your local telephone company. (See page 16 for details.) 3. LCD Screen: Shows call information, phone status, prompts and directory items. 4. SCROLL UP-DOWN, SHIFT LEFT-RIGHT Button: Press to move around the large LCD Screen. HANDSET Controls 5. PHONE BOOK Button: Press to access names and numbers stored in the DIRECTORY. (See pages 18 to 23 for details.) 6. REDIAL/SAVE/PAUSE Button: (SAVE) Press and hold down to save the changes on the listed items. (REDIAL) Press to redial the last number you dialed. (PAUSE) save/pause redial Press to insert a pause while dialing. (You will need the which use an alternative Long Distance Access Code.) redial save/pause button to dial numbers 7. HEADSET JACK: For connecting your headset plug to enjoy hands-free communication.

(See page 14 for detail.) 8. DIAL 10/0 Button: (DIAL 10) Press and hold down to place a local call with Area Code. 9. DIAL7/TEMPORARY TONE Button: (DIAL7) Press and hold down to place a local call. (*) Press to temporarily change the Dialing mode from Pulse to Tone for Rotary Service Users. (Press once before entering numbers to access the answering system or electronic banking service, etc.)

*7 10. EDIT/FLASH edit flash Button: (EDIT) Press to edit listed items. (FLASH) Press to answer a call if you have Call Waiting. 11. TALK talk Button: Press to answer an incoming call or to place a call. Press to end a call. 12. DELETE/SCAN Button: (DELETE) Press and hold down to delete items or individual characters. (SCAN) Press to change the operating channel when you hear interference. delete scan 13. MENU/VOICE MAIL menu voice mail Button: (MENU) Press and hold to access special functions operation in STANDBY mode. (For special functions see page 24.)

(VOICE MAIL) - Press to automatically dial the Voice Mail Post Code in your area to access your Voice Mail message. 14. HANDSET VOLUME CONTROL(HI, MID, LOW) Switch: Select the receiver volume level

(HI, MID, LOW). 15. TELEPHONE KEYPAD

9WXY Buttons: Allows you to make a call depending on pressed button. (For TELEPHONE KEYPAD characters, see page 31.) 16. DIAL 1+/#

#1+

Button: (DIAL 1+) Press and hold down to place a long distance call.

(Automatically adds the number 1 at the beginning of the displayed telephone number.) 17. INTERCOM outside line call to other HANDSET. intercom Button: Press to make an intercom call, or press to transfer a 18. CHARGE CONTACTS: For charging the BATTERY PACK inside the HANDSET. We recommend cleaning the CHARGE CONTACTS periodically with a damp cloth. BASE UNIT Controls 1 . TELEPHONE LINE CONNECTION JACK Pg. 6, 7, 10, 12, 46 2 . BASE UNIT A N T E N N A 3 . RING SELECT S W I T C H Pg. 37 4 . MESSAGE A L E RT S W I T C H Pg. 37 BASE UNIT Control 5 .P O W E R - I N CONNECTION JACK Pg. 6, 7 6 . TONE-PULSE SELECT SWITCH Pg.7, 46 7 . RINGER ON/OFF S W I T C H 8 .A N N O U N C E M E N T O N LY / I N C O M I N G MESSAGE SWITCH 1. TELEPHONE LINE CONNECTION JACK 2. BASE UNIT ANTENNA 3. RING SELECT Switch: To select the number of rings before the Answering System answers a call. 3R - System answers a call after third ring. 5R - System answers a call after the fifth ring. TS (TOLLSAVER) - System answers after the third ring only if you have new message. Otherwise, the system will answer after the fifth ring. 4. MESSAGE ALERT Switch: Set switch to ON to generate a beep sound every 15 seconds when a new message has been received. 5. POWER-IN CONNECTION JACK 6. TONE/PULSE Select Switch 7. RINGER ON/OFF Switch: Set switch to OFF position to disengage the ringer on the BASE UNIT. 8. ANNOUNCEMENT ONLY/INCOMING MESSAGE Switch:

ICM - System records the incoming messages. ANNC - System plays your announcement and then hangs up without recording messages. IMPORTANT Placing your BASE UNIT near appliances such as televisions, refrigerators, radios, or microwave ovens may cause interference. 2 BASE UNIT Controls 9. OUTGOING MESSAGE BUTTON Pg. 35~37 10.ANSWER FUNCTION ON/OFF BUTTON Pg. 36 11.MAILBOX 1 BUTTON Pg. 36, 38~40 12. PAGE BUTTON Pg. 29 13.ERASE BUTTON Pg. 35, 40 14.CHARGE TERMINALS 15.VOL- BUTTON Pg. 13, 36, 47 BASE UNIT Controls - Answering System 16.CODE BUTTON Pg. 41 17.SETBUTTON Pg. 34 18.MAILBOX 4 BUTTON Pg. 36, 38~40 19.DAY BUTTON Pg. 33, 40 20.HOUR BUTTON Pg. 34, 41 21.REPEAT BUTTON Pg. 39 22.SKIPBUTTON Pg. 39 9. OUTGOING MESSAGE 10. ANSWER FUNCTION ON/OFF Button: Press and hold down to record OGM message. Button: Press to activate or deactivate the answer function. The ANSWER FUNCTION ON/OFF LED indicator lights when the Answer function is turned ON. ogm 11. MAILBOX 1 1 Button: Press to activate functions for MAILBOX 1. 12. PAGE page Button: Press to page the HANDSET. 13. ERASE 14. CHARGE TERMINALS: For charging the H A N D S E T B AT T E RY PACK. For best Button: Press to erase messages. erase performance, clean the CHARGE TERMINALS periodically with a damp cloth. 15. VOL -

vol -

Button: Press to lower the speaker volume. 16. CODE code Button: Press to set the 3-digit Remote Access Code for remote operation. 17. SET set Button: Press to set/check the day and time. 18. MAILBOX 4 4 Button: Press to activate functions for MAILBOX 4. 19. DAY day Button: Press to set the day during time setting, or press to set the first digit of the access code during code setting. 20. HOUR hour Button: Press to set the hour during time setting, or press to set the second digit of the access code during code setting. 21. REPEAT rpt Button: Press to repeat messages. 22. SKIP skip Button: Press to skip messages.

BASE UNIT Controls 23.MAILBOX 2 BUTTON Pg. 36, 38~40 24.MINUTE BUTTON Pg. 34, 41 25.MEMO BUTTON Pg. 38, 40 26.VOL+ BUTTON Pg. 13, 36, 47 27.LED MESSAGE DISPLAY Pg. 13, 36~37, 39~40 28.SPEAKER BUTTON Pg. 13 29.MAILBOX 3 BUTTON Pg. 36, 38~40 30.IN USE LED INDICATOR 31.STOPBUTTON Pg. 8, 34, 36, 39, 47 32.CHARGE LED INDICATOR 33.PLAY BUTTON Pg. 38~39 34.MICROPHONE Pg. 35, 38 23. MAILBOX 2 2 Button: Press to activate functions for MAILBOX 2. 24. MINUTE min Button: Press to set the minute during time setting, or press to set the third digit of the access code during code setting. 25. MEMO memo Button: Press and hold down to record memo messages. 26. VOL +

27. LED MESSAGE DISPLAY: indicates the number of memos/messages received, status of Button: Press to increase the speaker volume. vol +

the system. Ea - Erase AO - Announce Only OP - OGM is playing FU - Memory is full 01 ~ 63 - No. of memos/messages PA - Pause 28. SPEAKER speaker Button: Press to answer the incoming call using the BASE UNIT. 29. MAILBOX 3 30. 3 Button: Press to activate functions for MAILBOX 3. IN USE LED Indicator: Lights up to indicate that the HANDSET is in TALK mode. 31. STOP stop Button: Press to stop playing a message. Press and hold down for more than 3 seconds to initiate/re-initiate your answering machine, then release the button and a beep will sound.(See detail operations in pages 34 and 47.) 32. CHARGE LED Indicator: Lights up when the HANDSET is placed on the BASE UNIT for charging. 33. PLAY 34. MICROPHONE play Button: Press to play messages. Contents Safety Instructions ------------------------------------------------------------------------------------------- 4 Getting Started ------------------------------------------------------------------------------------------------ 6 Desk Mounting ------------------------------------------------------------------------------------------------ 9 Wall Mounting ----------------------------------------------------------------------------------------------- 10 Cordless Telephone Operation -------------------------------------------------------------------------- 12 Preparing for Use --------------------------------------------------------------------------------------- 12 NO LINE Indicator --------------------------------------------------------------------------------------- 12 Receiving Calls ------------------------------------------------------------------------------------------ 12 Receiving Calls Using the BASE UNIT SPEAKERPHONE --------------------------------- 12 Placing Calls --------------------------------------------------------------------------------------------- 14 Headset Feature ---------------------------------------------------------------------------------------- 14 Redial Feature ------------------------------------------------------------------------------------------- 15 Caller ID System Operation ------------------------------------------------------------------------------ 16 Caller ID System ---------------------------------------------------------------------------------------- 16 Viewing Caller Information During Incoming Calls ------------------------------------------ 16 MSG WAITING (Message Waiting) ------------------------------------------------------------ 16 Call Waiting ------------------------------------------------------------------------------------------ 17 Voice Mail Function -------------------------------------------------------------------------------- 17 C-F (Forwarded Call) ------------------------------------------------------------------------------ 17 L-D-C (Long Distance Call) ---------------------------------------------------------------------- 17 Caller List ------------------------------------------------------------------------------------------------- 17 Viewing the Caller List ----------------------------------------------------------------------------- 18 Placing a Call From the Caller List ------------------------------------------------------------- 18 Editing the Caller List before Dialing ----------------------------------------------------------- 18 Saving the Name and Number in the Caller List into the DIRECTORY --------------- 19 Deleting All Records in the Caller List --------------------------------------------------------- 19 Selective Deleting in the Caller List ------------------------------------------------------------ 19 Special Note to Caller List for Multiple Handset user -------------------------------------- 19 Name and Telephone Number DIRECTORY ----------------------------------------------------- 19 Viewing the DIRECTORY ------------------------------------------------------------------------- 20 Speed Viewing the DIRECTORY --------------------------------------------------------------- 20 Saving in the DIRECTORY ----------------------------------------------------------------------- 20 1 Contents PREFERRED CALLS ----------------------------------------------------------------------------- 21 BLOCKED CALLS ---------------------------------------------------------------------------------- 21 Editing a Name and Number in the DIRECTORY ------------------------------------------- 21 Editing the Number in the DIRECTORY before Dialing ----------------------------------- 22 Placing Calls from the DIRECTORY ----------------------------------------------------------- 23 Deleting All Records in the DIRECTORY ----------------------------------------------------- 23 Selective Deleting in the DIRECTORY -------------------------------------------------------- 23 Function Operation ------------------------------------------------------------------------------------- 24 A. Language ---------------------------------------------------------------------------------------- 25 B. Silent On/Off ------------------------------------------------------------------------------------- 25 C. Time Set ------------------------------------------------------------------------------------------ 25 D. Ringer Volume ---------------------------------------------------------------------------------- 26 E. LCD Contrast ------------------------------------------------------------------------------------ 26 F. PBX Number ------------------------------------------------------------------------------------ 26 G. Flash Time --------------------------------------------------------------------------------------- 27 H. Pause Time -------------------------------------------------------------------------------------- 27 I. Voice Mail ---------------------------------------------------------------------------------------- 28 J. MSG Waiting (Message Waiting) ----------------------------------------------------------- 28 K. Handset Registration -------------------------------------------------------------------------- 29 L. RESET-------------------------------------------------------------------------------------------- 30 Telephone Keypad Characters ----------------------------------------------------------------------- 31 Multiple Handsets Feature ------------------------------------------------------------------------------- 32 How to Receive Calls ----------------------------------------------------------------------------------- 32 How to Place Calls -------------------------------------------------------------------------------------- 32 Privacy Feature ------------------------------------------------------------------------------------------ 32 Handset to Handset Intercom Call ------------------------------------------------------------------ 32 Transfer a Call to Other Extension Handset------------------------------------------------------- 33 Answering System Operation --------------------------------------------------------------------------- 34 Resetting the Answering System -------------------------------------------------------------------- 34 Setting the Day/Time Stamp-------------------------------------------------------------------------- 34 Recording your Outgoing Messages --------------------------------------------------------------- 35 Adjusting the Speaker Volume ---------------------------------------------------------------------- 36 Turning the Answering System ON/OFF ---------------------------------------------------------- 36 2 Setting to Answer Calls ----------------------------------------------------------------------------------- 37 Setting to Announce Only -------------------------------------------------------------------------------- 37 Screening Incoming Calls -------------------------------------------------------------------------------- 37 Message Alert ----------------------------------------------------------------------------------------------- 37 Setting Ring Select ----------------------------------------------------------------------------------------- 37 Recording a Memo ----------------------------------------------------------------------------------------- 38 Playing of Message/Memos ----------------------------------------------------------------------------- 38 Saving Messages ------------------------------------------------------------------------------------------ 39 Erasing Message ------------------------------------------------------------------------------------------- 40 When the Memory is Full --------------------------------------------------------------------------------- 40 Two-Way Recording --------------------------------------------------------------------------------------- 40 Remote Control Operation ----------------------------------------------------------------------------------- 41 Remote Operation through a Tone Telephone ------------------------------------------------------- 41 Remote Access Codes ------------------------------------------------------------------------------------ 41 Changing of the Remote Access Code ---------------------------------------------------------------- 41 Using the Remote Instruction Code -------------------------------------------------------------------- 42 Security----------------------------------------------------------------------------------------------------------- 43 Recharging the Battery Pack -------------------------------------------------------------------------------- 44 Changing the Battery Pack ---------------------------------------------------------------------------------- 45 Problem Solving ------------------------------------------------------------------------------------------------ 46 Technical Information ----------------------------------------------------------------------------------------- 48 FCC Requirements -------------------------------------------------------------------------------------------- 49 Warranty --------------------------------------------------------------------------------------------------------- 51 Wall Mounting Template -------------------------------------------------------------------------------------- 53 3 Safety Instructions IMPORTANT SAFETY INSTRUCTIONS To reduce the risk of fire, electric shock and/or injury, always follow these basic safety precautions when using your cordless telephone equipment. 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the telephone. 3. Unplug this telephone from the wall outlet before cleaning or replacing the BATTERY PACK. Do not use liquid cleaners or aerosol cleaners on the telephone. Use a damp cloth for cleaning. 4. Do not use this telephone near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool. 5. Place this telephone on a stable surface. Serious damage and/or injury may result if the telephone falls. 6. Do not cover the slots and openings on this telephone. This telephone should not be placed near or over a radiator or heat register. This telephone should not be placed in a built-in installation unless proper ventilation is provided. 7. Operate this telephone using the electrical voltage as stated on the BASE UNIT of the telephone or in the Owners Manual. If you are not sure of the voltage in your home, consult your dealer or local power company. 8. Do not place anything on the power cord. Install the telephone where no one will step or trip on the cord. 9. Do not overload wall outlets or extension cords as this can increase the risk of fire or electric shock. 10. Never push objects of any kind through the slots in the telephone. They could touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the telephone. 11. To reduce the risk of electric shock, do not disassemble this telephone. Take it to a qualified serviceman when service or repair work is required. Opening or removing covers may expose you to dangerous voltages or other risks. Incorrect reassembly can cause electric shock when the telephone is subsequently used. 12. Unplug this telephone from the wall outlet and consult a qualified service representative in any of the following situations:

A. When the power supply cord is frayed or damaged. B.If liquid has been spilled into the telephone. C. If the telephone has been exposed to rain or water. D. If the telephone does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions. Improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the telephone to normal operation. 4 Safety Instructions E. F. If the telephone has been dropped or the case has been damaged. If the telephone exhibits a distinct change in performance. 13. Do not use the telephone to report a gas leak in the vicinity of the leak. 14. Never install telephone wiring during a lightning storm. 15. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. 16. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. 17. Use caution when installing or modifying telephone lines. Battery Safety CAUTION:

Danger of explosion if the BATTERY PACK is replaced with incorrect type. Replace only with the same or equivalent type. To reduce the risk of fire or personal injury, read and follow these instructions:

1. Use only the following type and size of BATTERY PACK:

Cordless Telephone BATTERY PACK 3.6V, 750mAh U.S. Electronics Inc. Ni-MH BATTERY PACK: Model B660

(See page 44 for ordering information.) 2. Do not dispose of the BATTERY PACK in a fire. The BATTERY PACK may explode. Check with local codes for possible special disposal instructions. 3. Do not open or mutilate the BATTERY PACK. Released electrolyte is corrosive and may cause damage to the eyes or skin. Electrolyte may be toxic if swallowed. 4. Exercise care in handling the BATTERY PACK to prevent shorting the BATTERY PACK with conductive materials such as rings, bracelets, and keys. The BATTERY PACK or conductor may overheat and cause burns. 5. Charge the BATTERY PACK provided with (or identified for use with) this telephone only in accordance with the instructions and limitations specified in this manual. 6. Observe proper polarity orientation between the BAT T E RY PACK and BAT T E RY CHARGER. ATTENTION:

SAVE THESE INSTRUCTIONS The telephone that you have purchased contains a rechargeable BATTERY PACK. The BATTERY PACK is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this BATTERY PACK into the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal. 5 Getting Started Connecting Your Phone This section is a reference guide to the basic functions and operations of your cordless telephone. For more detailed descriptions of the operations and features of this telephone, refer to the Contents on page 1. 1. Carefully remove your cordless telephone from its shipping carton. If there is any visible damage, do not attempt to operate this equipment. Return it to the place of purchase. 2. Check to be sure you have all items that come with this cordless telephone system. You should have a H A N D S E T, BASE UNIT, AC ADAPTER, MOUNTING BRACKET, TELEPHONE LINE CORD, SHORT TELEPHONE LINE CORD, BELT CLIP, and an Owners Manual. HANDSET BASE UNIT MOUNTING BRACKET BELT CLIP TELEPHONE LINE CORD SHORT TELEPHONE LINE CORD AC ADAPTER BATTERY PACK 3. Insert the small plug on the end of the AC ADAPTER into the POWER-IN CONNECTION JACK at the back of the BASE UNIT. 4. Plug the AC ADAPTER into a 120V AC wall outlet, and the BASE UNIT POWER LED indicator will light up.

USE ONLY WITH CLASS 2 POWER SOURCE 12V DC, 500 mA. 5. Insert one plug of the TELEPHONE LINE CORD into the house TELEPHONE JACK and the other end into the TELEPHONE LINE CONNECTION JACK at the back of the BASE UNIT. (If you have an older 4-prong TELEPHONE JACK, you will need an RJ-11C TELEPHONE JACK ADAPTER. This adapter is available at the same place you purchased your telephone.) 6. We recommend not placing this unit next to appliances. Doing so may cause interference. 6 Getting Started 7. Install the BATTERYPACK by plugging it into the BATTERY CONNECTOR inside the BATTERY COMPARTMENT. The HANDSET LCD Screen will display WAIT REG. Follow the Handset Registration in page 29 to register your HANDSET. 8. Place the BATTERY PACK inside the BATTERY COMPARTMENT. 9. Slide the B AT T E RY COMPARTMENT COVER firmly into place in its closed position. H A N D S E T 10. IMPORTANT: Before initial use, charge the HANDSET for 12 hours. 11. TONE/PULSE Select Switch:

A. If your home is equipped with a tone dialing system, set the TONE/PULSE Select Switch to the TONE position. B. If you have a rotary dialing system, set the TONE/PULSE Select Switch to the PULSE position. C. If you are unsure which system you have, set the TONE/PULSE Select Switch to the TONE talk position. Press the button on the H A N D S E T and make a call. If the call connects, leave the switch as is; otherwise set to the PULSE position. 7 Getting Started ANTENNA HANDSET talk button to confirm that you Press the have a dial tone. If you do not get a dial tone, review steps 3 through 11. If you still do not have a dial tone, refer to the Problem Solving section on page 46. BELT CLIP HOOK With the back of the HANDSET facing up, insert one side of the BELT CLIP HOOK into the matching slot at the top side of the HANDSET. Press down on the opposite side of the BELT CLIP until the other HOOK locks into the slot on the side of the HANDSET. 12. Set the date and time on the HANDSET. (See page 25 for details.) 13. Press and hold the stop button to initiate your Answering System. (See details on page 34.) 14. Set the date and time on the BASE UNIT. (See page 34 for details.) You are now ready to use your new BellSouth Cordless Telephone. IMPORTANT In order to utilize the Caller ID feature, you must subscribe to Caller ID service from your local telephone company. 8 Desk Mounting Desk Mounting One of the special features of your telephone is the unique design of the MOUNTING BRACKET which can hold your phone at an angle when desk mounting or wall mounting. With the back of the BASE UNIT facing up, rotate the MOUNTING BRACKET to the position as in Figure 1 (follow the arrow direction for the DESK MOUNT). Place your telephone on any flat surface of desk as in Figure 2 FIGURE 1 FIGURE 2 IMPORTANT: Attach the MOUNTING BRACKET when using your phone on a desk. IMPORTANT Placing your BASE UNIT near appliances such as televisions, refrigerators, radios, or microwave ovens may cause interference. 9 Wall Mounting Wall Mounting You may choose to put the BASE UNIT of your cordless telephone on a wall. 1. With the back of the BASE UNIT facing up, rotate the MOUNTING BRACKETto the position 2. shown in Figure 1 (follow the arrow direction for the WALL MOUNT). Insert the small plug on the end of the AC ADAPTER into the POWER-IN CONNECTION JACK at the back of the BASE UNIT. 3. Plug the AC ADAPTER into a 120V wall outlet. 4. Connect the SHORT TELEPHONE LINE CORD to the TELEPHONE LINE CONNECTION JACK. Put the SHORT TELEPHONE LINE CORD inside the MOLDED WIRING CHANNEL as shown in Figure 2. 5. Plug the free end of the SHORT TELEPHONE LINE CORD into the MODULAR WALL JACK. FIGURE 1 FIGURE 2 10