FCC ID: 2ALSZ-CL3100N Photocontroller

Installation and Commissioning Procedure For iSLC3100-7P-N CIMCON Lighting, Inc. ISLC3100-7P-N Place the Photocontroller into the 7-pin NEMA receptacle and rotate it clockwise to lock. Fig. 1 Installation of ISLC3100-7P-N on the luminaire Page 1 Installation Procedure ISLC3100-7P Fig. 2: Installation wiring diagram Page 2 Installation Procedure ISLC3100-7P The cables protruding from the receptacle have following function as mentioned into table. Once the Photo-controller is installed and luminaire is powered ON then depending on the daylight condition Lamp will operate. In the Lab environment, you can just cover the cap with cloth or by hand and see the Lamp turning ON if wired correctly and if you remove the cloth, it will turn OFF. Page 3 Installation Procedure ISLC3100-7P iSLC SIM CARD NBIOT node comes with either ESIM configuration or Normal SIM configuration ESIM configuration: - ESIM will be solder on bottom of RF board with this configuration Normal SIM configuration: - For Normal SIM user need to arrange Micro SIM card and need to insert into module as per below. ESIM Configuration Page 4 Normal SIM Configuration Installation Procedure ISLC3100-7P Micro Size Sim Card Page 5 LED indication on RF board Installation Procedure ISLC3100-7P LED Indication chart Flicker slowly (200 ms High/1800ms Low) Network searching Flicker slowly (1800 ms High/200ms Low) Idle Flicker quickly (125ms High/125ms Low) Data transfer is ongoing Always high Voice calling Page 6 Safety Consideration for the Installation crew:

Ensure that the supply voltage matches the SLCs voltage rating. Installation Procedure ISLC3100-7P Firmly place the SLC into the NEMA twist lock receptacle/socket on top of the fixture by aligning the large prong on the SLC with the large opening in the receptacle/socket. Push down on SLC and twist clockwise until it locks into place. PHOTOCONTROL MUST BE LOCKED IN! Note: window or arrow on top of SLC should be pointed away from the mounting surface. The receptacle/socket may be repositioned by loosening the screw in the center of the receptacle/socket. Rotate to the new position and retighten screw. Do not rotate receptacle/socket over 360 degrees because you can twist receptacle/socket wires. Eventually stripping the insulation and cause the fixture to fail. To check operation during the daylight hours, cover the SLCs photocell window (or top surface) completely to simulate darkness. FCC Statement:

15.19 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operati on. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to p art 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interferen ce in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communic ations. However, there is no guarantee that interference will not occur in a particular installation. If this equip ment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 5.105 Page 7 Installation Procedure ISLC3100-7P FCC Radiation Exposure Statement This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation d istance of at least 20 cm from all persons and must not be co-

located or operating in conjunction with any other antenna or transmitter. End-

users and installers must be provided with antenna installation instructions and consider removing the no-

collocation statement. Page 8

Photocontroller iSLC3100-7P-N 120-277V AC, 50/60HzZ 8A, Electronic Ballast Temp: -40C to +70C, FID 10/20 iSLC3100-7P-N-A-G-IO-CATC-05 Photocontroller iSLC3100-7P-N 120-277V AC, 50/60Hz 8A, Electronic Ballast Temp: -40C to +70C, FID8 01/21 iSLC3100-7! -G-IO-CATC-05 40mm X 17mm FCC ID: 2ALSZ-CL3100N This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. 44 mm x 14.5 mm

FCC, Request for non-disclosure RF_501, Issue 8 Date: 23-Dec-2020 Page 1 of 1 Company Name: CIMCON Lighting, Inc. Address:

City:

Country:

200 Summit Drive,Suite 500, South Tower Burlington United States Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands To: Telefication B.V., Dept. FCC TCB Subject: Request for confidentiality FCC ID: 2ALSZ-CL3100N Reference number: ######

Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application:

Bill(s) of Material Block Diagrams Operational Description Schematic Diagrams Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commissions policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, applicant hereby requests Short-Term Confidential treatment of the following materials (See notes below):

Internal Photos Users Manual Test Set-up Photos External Photos Justification:

Name and signature of applicant: Sudhanshu Jha Date: 2020-12-23 Notes:

1) A document or type of document can only have ONE type of confidentiality!

2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)!

The planned date should stated in the RF731 application form. 3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this!

5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period

www.cimconlighting.com RF_160, Issue 04 BTL Inc. 4F,No.18, Ln. 171, Sec. 2, Jiuzong Rd., Neihu Dist.114, Taipei Taiwan Declaration of Authorization We Name: CIMCON Lighting, Inc. Address: 200 Summit Drive, Suite 500, South Tower City: Burlington State: Massachusetts Country: United States Declare that:

Name Representative of agent: Ms. Melody Wu Agent Company name:

Address:

City:

Country is authorized to apply for Certification of the following product(s):

Product description: Photocontroller Type designation: ISLC3100-7P-N Trademark: CIMCON Validity/ expiry date: From December 23, 2020 to December 22, 2021 on our behalf. Date:December 23, 2020 City: Burlington Name: Sudhanshu Jha Function: VP - Engineering Signature:

Notes:

(1): Required for FCC application

(2): For FCC it must be the Grantee Code owner or the authorized agent. Worldwide Headquarter 200 Summit Drive, Suite 500, South Tower, Burlington, MA 01803 Tel:(978)-320-4002 Fax:(978)-299-5212 Asia Pacific Office 802, Sakar IV, Ellisbridge, Ahmedabad-380 006, India Tel: +91-79-2657 8639 Fax: +91-79-2657 8659