MANUAL BOOK Product Name:Wireless HD/SDI video transmission system with TALLY and TALKBACK Model Name:1000tr Manufacture:ShenZhen LanGi Technology Co. LTD Contents Cautions Wireless Video Transmission Systems Product Features Specifications Transmitter Receiver User Manual Setting Up the Unit Setting Up the Intercom Setting Transmission Output Power Channel Settings Turning Fan On/Off Troubleshooting Disclaimers 2 3 4 5 7 9 11 11 13 13 14 14 15 17 1 Cautions Warning Please read this user introduction manual to become familiar with the features before operation. Failure to operate the product correctly can result in damage to the product, or interference with other devices. This is a sophisticated product which must be operated with caution and common sense. Failure to operate this product properly might result in disturbing other film equipment on set. This product is not intended for use by children without direct adult supervision. Do not use with incompatible components, or alter this product in any way outside of the documents provided by. These safety guidelines contain instructions for installation, operation, and maintenance. It is essential to read and follow all of the instruction in the manual, and all the notices and warnings regarding series products prior to assembly, setup, or use to prevent any damage or interference. 1. Do not use this product in extreme heat, cold, dusty, or humid environments. 2. Prevent friction against hard objects. 3. Prevent jarring, such as from falling from high places, or from improper packaging during transportation. 4. These products are not waterproof; prevent moisture from getting in, on, or around the unit(s). 5. Do not dismantle, assemble, or otherwise alter the product(s) arbitrarily. Electrical Considerations 1. When this device is sharing a power supply or battery with other equipment, please make sure all signal and power cables are well connected before turning on the unit power. 2. When this device is sharing a power supply or battery with other equipment, please make cables from the unit. 3. When this device is sharing a power supply or battery with other equipment, please check the polarity of the power connectors of all equipment to ensure the inside conductor is positive. If the polarity of the power connector is unknown, please check the user manual to make sure the outer conductor of the SDI or HDMI connector is connected to the negative of the power supply. Otherwise, the equipment will not be able to share the same power supply with the unit. 2 Product Features Transmits 10-bit color, YCbCr, 4:2:2 color depth, proprietary color matching algorithm on OFDM chips. Optimized uncompressed 10-bit 4:2:2 2GBps video stream, or 12-bit 4:4:4 3GBPs wireless video transmission on other models. Optimized video processor for on-screen movement. Fully supports all audio formats. Static channel selection. The channel number and frequency can be modified by software to avoid interference from other devices. Supports multiple receivers and AES 128 bit video encryption. FPGA technology adopting American IRTA programmable logic matrix chips. Follows the international film association time code protocols. Accurate time code extraction, transmission, and encryption using embedded time code transmission method. Hardware encrypted time code to IRTA chips. Software allows user to adjust transmission output power to avoid interference. Uses a separate channel to transmit tally information. Fully supports different intercom interfaces. Integrated wireless intercom feature supports up to 300 meters for microphone and speakers. 4 Specifications Transmitter SPECIFICATION Frequency Low band: 5190 and 5230MHz High band: 5755 and 5795MHz 2.4-2.483GHz with ISM band Modulation method and OFDM/40MHz for video Bandwidth GFSK/1MHz for intercom system Video Formats Supported Audio Formats Supported Time Code 1080p 23.98/24/25/30/50/60 1080psf 23.98/24/25 1080i 50/59.94/60 720p 50/59.94/60 576p 576i 480p 480i PCM, DTS-HD, Dolby TrueHD SMPTE-12M Transmission Range 2500ft(Line of sight) Antenna Transmitter External Antenna 5G 2pcs External Antenna 2.4G x1pcs Transmission Power 18dBm Functional Interface HDMI Input; SDI Input; SDI Loop Output; Mini USB; LEMO Power IN; Antenna RPSMA Socket; Power ON/OFF,3.5mm HP/MIC socket TALLY output for Wrist Mounting Structure 1/4 Hot-shoe connection OLED Display Power Source Channel Info; Video status; Battery capacity;
Status Menu, Audio Volume 9-18V for DC input, V-Mount or G-Mount battery (depending on the model) Power Consumption 7.5-8.5W 5 Specifications Net Weight(with antenna) Temperature Antenna 400g
-10-40 (Operating); -40-80 (Storage) Receiver External Antenna for 5G 5pcs External Antenna for 2G x1pcs Receiving Sensitivity
-70dBm Functional Interface SDI Dual Output; HDMI Output; Mini USB;
LEMO Power IN; Antenna RPSMA Socket;
Power ON/OFF, 3.5mm HP/MIC socket;3.5mm TALLY socket; LEMO 6 needle Locating Structure 1/4 Hot-shoe connection OLED Display Power Source Channel Info; Signal Strength; Power Info;
TALLY indicator 9-18V for DC input; V-Mount or G-Mount battery (depending on the model) Power Consumption 7.5-8.5W Net Weight(with antenna) Temperature 800g
-10-40 (Operating); -40-80 (Storage) 6 Transmitter 14 5G Antenna 15 Battery Clip 16 Rear TALLY T M E N U O F F S D I I N T A L L Y I M C H P
/
1 Front TALLY 2 2.4G Antenna 3 LCD Display 4 VOL +/sel 5 VOL -/sel 6 MENU 7 Power ON/OFF 8 EXT TALLY output 9 MIC/HP 10 SDI IN O N S D I O U T H D M I I N D C I N 9 V
-
1 8 V 11 SDI OUT(Loop Through) 12 HDMI IN 9V-18V
+
13 Power Supply IN(Lemo) 7 Transmitter 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 STRUCTURE 15mm Front TALLY indicator (Red/Yellow) The indicator color will be the same (Red/Yellow) for rear, front, and external TALLY. 2G Antenna Connector SMA connector for 2.4G antenna. OLED Display Displays information for channel, video status, signal strength, battery voltage indicator, and MENU information. VOL + / UP Button Volume + function. In MENU mode, the button functions as an UP key. VOL - / DOWN Button Volume - function. In MENU mode, the button functions as a DOWN key. MENU Button MENU select. In MENU mode, the button functions as a confirm key. Power ON/OFF Power ON or OFF the transmitter. 3.5mm External TALLY Output Interface Maximum output current of 20mA, can support LED. 3.5mm MIC/HP Interface Connect to external converter box. SDI IN Connect to video source. Supports 3G-SDI, HD-SDI, SD-SDI. SDI OUT (Loop Through) Connect to other SDI equipment if needed. HDMI IN Connect to HDMI video source. DC Power In (Lemo) Supports 9-18V. 5G Antenna Connectors RPSMA connectors for 5G antennas. Battery Clip Battery compartment, for F550/F970 batteries. Rear TALLY (Red/Yellow) The indicator color will be the same (Red/Yellow) for rear, front, and external TALLY. 8 Receiver 9 Receiver 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 STRUCTURE 5G Antenna Connectors RPSMA connectors for antennas. OLED Display Channel, signal strength, battery voltage, audio volume, and MENU. MENU Button Unlock and confirm selection. LEFT / UP Button Select channels. RIGHT / DOWN Button Select channels. V+ / UP Button Volume +. V- / DOWN Button Volume -. BAT-OUT Provides DC power from the battery for an external device. INTERCOM 6pin LEMO for TALLY and intercom system. 3.5mm External TALLY Output Interface Maximum output of 20mA, can support LED. 3.5mm MIC/HP Interface Connect to external headphone. HDMI OUT Video output, connect to HDMI receiver or device. SDI OUT Video output (video output is the same from the two SDI interfaces), connect to SDI receiver or device. DC Power In (LEMO) Supports 9-18V. 2.4G Antenna Connector SMA connector for 2.4G antenna. Battery Clip V-Mount battery (default) battery plate. Power ON/OFF Power ON or OFF the receiver. 1 0 User Manual 1. Fix the three antennas to the transmitter and arrange them to be a right angle as below figure to get better performance. 2. On transmitter side, when both SDI and HDMI source are inputted, the transmitter will automatically select the SDI source for transmission 3. Fix the five antennas to receiver and arrange them to a right angle as figure to get better performance. 4. Setting the receiver higher will enhance the transmission distance. 11 User Manual Transmitter Fix the three antennas (5G x2, 2.4G x1) respectively. Connect the SDI or HDMI video source to the SDI IN/HDMI IN of transmitter (when both SDI and HDMI video are inputted, it will auto select the SDI video for transmission). If needed, you can connect the SDI out (loop through) to other equipment as well. Connect the DC power to the transmitter or use a battery on the battery plate. Power on the transmitter. Set the Channel (must set both transmitter and receiver to the same channel) Receiver Fix the six antennas (5Gx5, 2.4Gx1) respectively. Connect the SDI OUT/HDMI OUT port of the receiver to the monitor or other device. Connect DC power via power cable or use V-lock battery on the battery plate. Power on the receiver. Set the Channel (must set both transmitter and receiver to the same channel). After 5-10s, the video transmission will be shown on the monitor. 12 User Manual Setting Up the Intercom After connecting the units, power on both Transmitter and Receiver. On the Transmitter side, you will hear sound from the receiver end if TALK is not pressed on converter box. When the TALK button is pressed and held, both the receiver end and the transmitter end can conversation normally. The receiver end can hear call sound when the operators on the Transmitter side press down the CALL button on CALL box. When TALLY is triggered via a professional broadcast switcher, the OLED area on the receiver glow red. At the same time, the TALLY LED will be lit on the Transmitter (You can also insert your wrist indicator if desired). Note: The external TALLY ( wrist LED) interface only supports LED lights at 3.3V@20mA. Intercom System Pairing Transmitter (TX) side: Press MENU button first, then press UP or DOWN buttons to choose Talk Pair on screen and press MENU button again to confirm. Receiver (RX) side: Press VOL- button first, then press RIGHT button to start intercom pairing. Transmitter (TX) side will auto restart, Receiver(RX) side should be manually restarted. When both sides are restarted, Intercom system pairing is complete. 13 User Manual Channel Settings Both Transmitter and Receiver are set to the same channel by default. If you want to change to a new channel, please follow the instructions below. Note: Both transmitter and receiver must be set to the same channel to work. Changing Channel on Transmitter Power on the Transmitter Press the MENU button, then press UP or DOWN to choose Channel Set on screen. Press MENU to confirm. Press UP or DOWN to choose channel, then press MENU to confirm. Transmitter channel setting accomplished. Changing the Channel on Receiver Power on the Receiver. Press and hold MENU button until display unlock icon appears Click LEFT or RIGHT buttons to choose channel, then click MENU to confirm. Receiver channel setting accomplished. Turning the Fan On or Off Press the + and - buttons on the transmitter simultaneously for 3 seconds. Press + or - to select FAN. Press MENU to confirm. Press + or - to turn fan ON or OFF. Press MENU to confirm. 14 User Manual Troubleshooting If the Receiver fails to output video correctly, follow the chart below to find possible causes and solutions. ISSUE SOLUTION Displaying Waiting for Connection... for a Prolonged Period Transmitter is not powered up. Turn on the transmitter. Transmitter or receiver is not placed correctly. Place the TX or RX correctly. The transmitter and receiver are too far away. Move the receiver closer to the transmitter. Several solid wall partition on TX and RX. Reduce the number of obstructions between the TX and RX. V T n o n o i t a m r o f n I D S O There are too many obstacles between TX and RX. Move the receiver closer to the transmitter. Other transmitter is working on the same or adjacent channel Turn off other transmitter, or change channel. No Video Signal Received Transmitter and video source are not connected. Connect the transmitter to video source by SDI/HDMI cable. The video source is turned OFF Turn on the video source. Bad connection of transmitter cable Disconnect and re-connect the transmitter. Transmitter is working abnormally Restart the transmitter. Problem with the cable between TX and video source Change the SDI/HDMI cable. Player does not support the output resolution format Switch the output video resolution to other modes. The TV/Monitor does not support HDCP authentication Replace TV/Monitor with HDCP-Certified TV/Monitor. 15 User Manual No Signal Input to Receiver or TV/Monitor Receiver is turned off. Turn on the receiver. Receiver and TV are not connected. TV/Monitor not switched to SDI/HDMI input Connect receiver and TV/Monitor via SDI/HDMI input. Switch TV/Monitor to SDI/HDMI input. Bad cable connection of receiver or TV/Monitor. Disconnect and re-connect the SDI/HDMI cable. e g a m I TV/Monitor turned to standby mode. Switch the TV/Monitor to normal operation mode. Receiver is working abnormally. Restart the receiver. No Image Appears on the TV/Monitor Bad connection from receiver or cable. Reconnect the cable of the receiver or TV/Monitor. Receiver is working abnormally. Restart the receiver. Receiver failure. Please contact your retailer. Abnormal Color on TV Screen Bad connection from receiver cable or TV/Monitor. Disconnect and re-connect the HDMI cable of the receiver or TV. Bad connection from transmitter cable or video source. Disconnect and re-connect the HDMI cable of the transmitter and player. Transmitter or receiver working abnormally. Restart transmitter and receiver. 16 Disclaimers FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -----
Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. (Example use only shielded interface cables when connecting to computer or peripheral devices). FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with part 15 of the FCC Rules.Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. Cautions The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment. 17 Industry Canada licence-exempt RSS standard(s). IC Warning This device complies with Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Cet quipement est conforme aux limites d'exposition aux radiations de la FCC dfinies pour un environnement non control. environnement. Cet quipement doit tre install et utilis avec une distance minimale de 20 cm entre le radiateur et votre corps. This radio transmitter [IC: 23214-1000TR] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. 2.4G transmitting antenna:
Antenna type: whip antenna with RP-SMA connector;
Maximum antenna gain:3.5dBi;
Model name: 1000tr.