FCC ID: PKW-WUSB11-V26 Wireless LAN USB Adapter

Inform Letter Dear Customer, According to FCCs regulation, the following Declaration of Conformity has to be made by a company located in USA. They are:

This device has been confirmed to be in compliance with the requirements of ANSI C63.4 & FCC part 15 regulations. The test result has been shown in the ADT test report with number RF910208R02A. And this compliance is subject to the following two conditions:

(1) This device may not cause harmful interference and,

(2) This device must accept any interference received, including interference that may cause undesired operation. This declaration can be a separate sheet and be sure that the following message will be also included in this declaration:

1) Product name, model name and trade name. 2) Company name, and address of the one who is responsible for this declaration. 3) Name, title, telephone and fax number as well as the signature of the contact person. Thanks for your attention.

1. To install your Wireless USB Network Adapter, click on the Install tab. 2. Once you see the following screen, click the Next button to continue. Installation and Configuration of the USB Adapter for Windows This Wireless USB Network Adapter Setup Utility will guide you through the Install and Uninstall Procedure for Windows 98, Millennium, 2000 and XP. Insert the Setup Utility CD into your CD-ROM Drive. The Setup Utility should run automatically and the screen shown below should appear. If it does not, click the Start button and choose Run. In the box that appears, enter D:\setup.exe (where D is the letter of your CD-ROM drive). 3. After reading to the Warranty Policy, click the Yes button if you agree, or No to end the installation.

The Install tab begins the software installation process, as shown on the next page.

The Uninstall tab shows you how to uninstall the adapter (please see the sec-tion titled Uninstall Procedures for more information).

The User Guide tab shows you a PDF file of the User Guide.

The Contact Us tab links you to the Linksys website.

The Exit tab allows you to the exit the Setup Utility.

4. The InstallShield Wizard will automatically choose a folder where Setup will install files. Click the Next button. 6. If you chose Infrastructure Mode, go on to Step 7 now. If you chose Ad-Hoc Mode, choose the correct operating channel that applies to your network. The channel you choose should be set as the same as the other points in your wireless network. The default channel is set to Channel 6. Click Next. 5. The InstallShield Wizard will ask you to choose a wireless mode. Choose the mode that applies to your network. Ad-Hoc Mode is used for simple peer-to-peer networking or sharing of local resources between wireless Networked PCs, and Infrastructure Mode allows a wireless network to be integrated into an existing, wired network through an access point, permit-ting roaming between access points while maintaining a connection to all network resources. Then, click the Next button. 7. Enter in the name of your SSID for your Ad-Hoc or Infrastructure setting. The SSID must be identical for all points in the network. To join any avail-able SSID, type ANY. The default setting is linksys (all lowercase). Click Next. 8. The Wizard will ask you to review your settings before starting to copy files. Select Back to review or change any settings, or select Next if you are satis-fied with your settings. 10. Once the Wireless USB Network Adapter Configuration Utility has been successfully installed, the Wizard will ask you to restart your computer. Select Yes, I want to restart my computer now, and then click Finish to restart. 9. The InstallShield Wizard will begin copying the files. The bar in the middle of the screen below shows the percentage of files copied. You have now completed the installation of your Wireless USB Network Adapter Configuration Utility. Please go on to the next page for informa-tion on Connecting the Wireless USB Network Adapter.

Configuring the USB Network Adapter 2. Select the Connection tab. In the Connection lists, you can double click one of the items in the list box to make an association to the wireless profile. The items with no profile name is the existing wireless network in the air. You may get a connection to them by double click on the list item. After installing the Network Adapter, Windows 98, Millennium, 2000 and XP will automatically identify the adapter. Next, you may need to configure The adapters utility software. 1. After installing the Network USB Adapter, the blue Linksys 802.11b Wireless LAN Configuration Utility icon will appear on your system tray. double-click of the icon of the green monitor in the diagram below, and the following screen will appear:

This screen shows you the status of your current connection. 3.Select the Profile Setting tab. The items list on the list box shows you the profile currently exist. Click on New button to add a new profile.

4. When you click on the New button, the new profile dialog box will show out to allow you to key in some profile data. You may key in a profile name, Network Name to associate to wireless network, Network Type for Infrastructure or Ad-hoc; If you click Ad-hoc, you can click the task bar, then choose the Chanel. Profile 1 Profile 3 5. When you click the Advance button, the Advance dialog box will display. Users can insert and select the data. WEP for 64bits or 128bits; In order to enable WEP encryption, hexadecimal values must be inserted in WEP Key item. The value must match the Key on all other devices on the wireless network or else this device will be unable to transmit or receive data. Profile 2 Advance 1

Advance 2 5. The About tab shows you copyright and version information about the driver, the configuration utility, and the firmware. The version number of the driver may vary from this screen, depending on which version was shipped with your Adapter. You can always visit www.linksys.com for the latest version of the driver. Advance 3 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. FCC Caution: To assure continued compliance, (example -

use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE:

FCC RF Radiation Exposure Statement:

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. EU Countries Not Intended for Use None. Potential Restrictive Use France: Only channels 10,11,12, and13 R&TTE Compliance Statement This equipment complies with all the requirements of the DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of 9 March 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity (R&TTE). The R&TTE Directive repeals and replaces in the directive 98/13/EEC

(Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of April 8, 2000. Safety This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this manual and of the computer manufacturer must therefore be allowed at all times to ensure the safe use of the equipment. EU Countries Intended for Use The ETSI version of this device is intended for home and office use in Austria, Belgium, Denmark, Finland, France (with Frequency channel restrictions), Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. The ETSI version of this device is also authorized for use in EFTA member states Iceland, Liechtenstein, Norway and Switzerland.