FCC ID: LDKHDGWI1903 Cisco Catalyst 9117AX Series

 

D r a f t L a b e l - C i s c o C o n f i d e n t i a l GETTING STARTED GUIDE Cisco Catalyst 9117AX Series Access Points First Published: February 22, 2019 Cisco Systems, Inc. 1 www.cisco.com Cisco Catalyst 9117AX Series Access Points D r a f t L a b e l - C i s c o C o n f i d e n t i a l 1 About this Guide 2 About the Access Point 3 Safety Instructions 4 Unpacking 5 AP Views, Ports, and Connectors 6 Installation Overview 6 Installation Overview 7 Performing a Pre-Installation Configuration 9 Mounting the Access Point 10 Powering the Access Point 11 Configuring and Deploying the Access Point 12 Checking the Access Point LEDs 13 Miscellaneous Usage and Configuration Guidelines 15 Related Documentation 16 Declarations of Conformity and Regulatory Information 17 Obtain Documentation and Submit a Service Request 2 Cisco Catalyst 9117AX Series Access Points D r a f t L a b e l - C i s c o C o n f i d e n t i a l 1 About this Guide This guide provides instructions on how to install your Cisco Catalyst 9117AX series access points and provides links to resources which can help you configure the access point. This guide provides mounting instructions and limited troubleshooting procedures. The 9117AX series access point is referred to as access point or AP in this document. 2 About the Access Point The Cisco Catalyst 9117AX Series wireless access point is a dual band, dual concurrent, enterprise 802.11ax AP. This AP series offers integrated antenna options, designed to use both 2.4 GHz and the 5 GHz bands. This access point supports a greater overall High Density Experience (HDX) which provides a more predictable performance for advanced applications such as 4K or 8K video, high-density high-definition collaboration applications, all-wireless offices and Internet-of-Things (IoT). The access point supports full interoperability with leading 802.11ax and 802.11ac clients, and supports a mixed deployment with other access points and controllers. A full listing of the access point's features and specifications are provided in the Cisco Catalyst 9117AX Series Access Point Data Sheet, at the following URL:

<URL to be added at CCO>

Access Point Features The 9117AX series access point is a wireless controller-based product and supports:

Four dual-band integrated antennas on the 9117AX-I access point models (C9117AXI-x and C9117AXI-ME-x) Note The x in the model numbers represents the regulatory domain. For information on supported regulatory domains, see theAP Model Numbers and Regulatory Domains section on page 5. Integrated internal antennas, omnidirectional in azimuth for both 2.4 GHz (peak gain 2.6dBi) and 5 GHz (peak gain 4.4dBi) Simultaneous 4x4 MIMO with four spatial streams for 2.4 GHz band and 8x8 MIMO with eight spatial streams for 5 GHz band The following hardware external interfaces:

1x100/1000/2500/5000 Multigigabit Ethernet (RJ-45) RS-232 Console Interface through RJ-45 Recovery push button (enables partial or full system configuration recovery) USB 2.0 Port One multi-color LED Status indicator. see the Checking the Access Point LEDs section on page 17 for information on the colors of the LED status indicator. Multiuser Multiple-Input Multiple-Output (MU-MIMO) technology with 4 spatial streams. Orthogonal Frequency Division Multiple Access (OFDMA)-based scheduling splits the bandwidth into smaller chunks called resource units (RU) which can be allocated to individual clients in both the downlink and uplink to reduce overhead and latency. 3 Cisco Catalyst 9117AX Series Access Points D r a f t L a b e l - C i s c o C o n f i d e n t i a l Spatial Reuse (also known as BSS coloring) allows APs and their clients to differentiate between BSSs, thus permitting more simultaneous transmissions. Built-in BLE radio (Bluetooth 5.0) mGig Ethernet (1G,2.5G, 5G, and 100M) Supports up to 500 Wi-Fi devices New power savings mode called Target-Wakeup-Time (TWT), allows the client to stay asleep and wake up only at pre-scheduled (target) times to exchange data with the AP. This allows for significant energy savings for battery-operated devices. Cisco Digital Network Architecture (DNA) support enables Cisco Connected Mobile Experiences, Apple FastLane and Cisco Identity Services Engine Cross-AP Noise Reduction, a Cisco innovation that enables APs to intelligently collaborate in real time about RF conditions so that users connect with optimized signal quality and performance. Optimized AP Roaming for ensuring that client devices associate with the AP in their coverage range that offers the fastest data rate available. Cisco ClientLink 4.0 technology for improved downlink performance to all mobile devices, including one-, two-, and three-spatial-stream devices up to 802.11ac Wave 1 and Wave 2. The technology also improves battery life on mobile devices. Cisco CleanAir technology enhanced with 160MHz channel support. CleanAir delivers proactive, high-speed spectrum intelligence across 20-, 40-, and 80-, and 160-MHz-wide channels to combat performance problems arising from wireless interference. MIMO equalization capabilities, which optimize uplink performance and reliability by reducing the impact of signal fade. The AP supports both Cisco Mobility Express and lightweight deployments (using Cisco Wireless LAN controllers). The AP also supports the following operating modes:

LocalThis is the default mode for the Cisco AP. In this mode, the AP does not serve clients. FlexconnectFlexconnect mode for the Cisco AP. MonitorThis is the monitor-only mode for the Cisco AP. SnifferIn the wireless sniffer mode, the AP starts sniffing the air on a given channel. It captures and forwards all the packets from the clients on that channel to a remote machine that runs Airopeek or Wireshark (packet analyzers for IEEE 802.11 wireless LANs). This includes information on the time stamp, signal strength, packet size, etc. Note In the sniffer mode, the server to which the data is sent should be on the same VLAN as the wireless controller management VLAN otherwise an error will be displayed. 4 Cisco Catalyst 9117AX Series Access Points D r a f t L a b e l - C i s c o C o n f i d e n t i a l AP Model Numbers and Regulatory Domains AP Type Access Point for indoor environments, with internal antennas Model Number C9117AXI-x C9117AXI-ME-x Details Dual-band, controller-based 802.11ax Dual-band, 802.11ax, factory-shipped with a Cisco Mobility Express software image You need to verify whether the AP model you have is approved for use in your country. To verify approval and to identify the regulatory domain that corresponds to a particular country, visit http://www.cisco.com/go/aironet/compliance. Not all regulatory domains have been approved. As and when they are approved, this compliance list will be updated. Antennas and Radios The 9117AX series access point contains a dedicated 2.4 GHz radio and a 5 GHz radio. The access point configurations are:

C9117AXI-xOne 2.4 GHz radio and one 5 GHz radio. C9117AXI-ME-xOne 2.4 GHz radio and one 5 GHz radio. Internal Antennas The 9117AXI has 8 cross polarized internal antennas. 5 Cisco Catalyst 9117AX Series Access Points D r a f t L a b e l - C i s c o C o n f i d e n t i a l 3 Safety Instructions Translated versions of the following safety warnings are provided in the translated safety warnings document that is shipped with your access point. The translated warnings are also in the Translated Safety Warnings for Cisco Catalyst Access Points, which is available on Cisco.com. Warning IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. SAVE THESE INSTRUCTIONS Statement 1071 Warning Read the installation instructions before using, installing or connecting the system to the power source. Statement 1004 Warning Installation of the equipment must comply with local and national electrical codes. Statement 1074 Warning Do not operate your wireless network device near unshielded blasting caps or in an explosive environment unless the device has been modified to be especially qualified for such use. Statement 245B Warning In order to comply with FCC radio frequency (RF) exposure limits, antennas should be located at a minimum of 12 inches (30 cm) or more from the body of all persons. Statement 332 Caution The fasteners you use to mount an access point on a ceiling must be capable of maintaining a minimum pullout force of 20 lbs (9 kg) and must use all 4 indented holes on the mounting bracket. Caution This product and all interconnected equipment must be installed indoors within the same building, including the associated LAN connections as defined by Environment A of the IEEE 802.af Standard. Warning This equipment is suitable for use in environment air spaces (plenums) in accordance with Section 300.22 (C) of the National Electrical Code, and Sections 2-128, 12-010(3) and 12-100 of the Canadian Electrical Code, Part 1, CSA C22.2. External power supply, power adapter and/or power injector, if provided, are not suitable for installation in air spaces. Statement 440 Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040 6 Cisco Catalyst 9117AX Series Access Points D r a f t L a b e l - C i s c o C o n f i d e n t i a l 4 Unpacking To unpack the access point, follow these steps:

Step 1 Unpack and remove the access point and the accessory kit from the shipping box. Step 2 Return any packing material to the shipping container and save it for future use. Step 3 Verify that you have received the items listed below. If any item is missing or damaged, contact your Cisco representative or reseller for instructions. The access point Mounting bracket (AIR-AP-BRACKET-1=, selected when you ordered the access point) Adjustable ceiling-rail clip (selected when you ordered the access point) Power Injector AIR-PWRINJ6= (only if selected when you ordered the access point). 7 Cisco Catalyst 9117AX Series Access Points D r a f t L a b e l - C i s c o C o n f i d e n t i a l 5 AP Views, Ports, and Connectors Figure 1 Face of the 9117AXI Model 1 Status LED 2 Location of the ports and connectors on the head of the AP. Figure 2 Ports and Connectors on the Head of the 9117AXI Model 1 Mode button Console port 2 USB port 3 4 5 6 8 Cisco Catalyst 9117AX Series Access Points D r a f t L a b e l - C i s c o C o n f i d e n t i a l 6 Installation Overview Installing the access point involves these operations:

Performing a Pre-Installation Configuration, page 10 (optional) Installation Overview, page 9 Step 1 Step 2 Step 3 Mounting the Access Point, page 13 Step 4 Powering the Access Point, page 14 9 Cisco Catalyst 9117AX Series Access Points D r a f t L a b e l - C i s c o C o n f i d e n t i a l 7 Performing a Pre-Installation Configuration The following procedures ensure that your access point installation and initial operation go as expected. This procedure is optional. Note Performing a pre-installation configuration is an optional procedure. If your network controller is properly configured, you can install your access point in its final location and connect it to the network from there. See the Deploying the Access Point on the Wireless Network section on page 15 for details. The following Pre-Installation Configuration procedure given does not include configuring Link Aggregation. For information on configuring Link Aggregation, see the Cisco Wireless LAN Controller Configuration Guide, Release 8.2, at this URL:

http://www.cisco.com/c/en/us/td/docs/wireless/controller/8-2/config-guide/b_cg82.html The pre-installation configuration setup is illustrated in Figure 3. Figure 3 Pre-Installation Configuration Setup Controller Layer 3 devices Link Aggregation Link Aggregation Cisco Aironet access points 6 6 0 4 5 3 To perform pre-installation configuration, perform the following steps:

Step 1 Make sure that the Cisco wireless LAN controller DS port is connected to the network. Use the CLI, web-browser interface, or Cisco WCS procedures as described in the appropriate Cisco wireless LAN controller guide. a. Make sure that access points have Layer 3 connectivity to the Cisco wireless LAN controller Management and AP-Manager Interface. b. Configure the switch to which your access point is to attach. See the Cisco Wireless LAN Controller Configuration Guide for the release you are using, for additional information. c. Set the Cisco wireless LAN controller as the master so that new access points always join with it. 10 Cisco Catalyst 9117AX Series Access Points D r a f t L a b e l - C i s c o C o n f i d e n t i a l d. Make sure DHCP is enabled on the network. The access point must receive its IP address through DHCP. Note A Wave 2 Cisco AP will be assigned an IP address from the DHCP server only if a default router (gateway) is configured on the DHCP server (enabling the AP to receive its gateway IP address) and the gateway ARP is resolved. This is not applicable to Wave 1 Cisco APs. e. CAPWAP UDP ports must not be blocked in the network. f. The access point must be able to find the IP address of the controller. This can be accomplished using DHCP, DNS, or IP subnet broadcast. This guide describes the DHCP method to convey the controller IP address. For other methods, refer to the product documentation. See also the Configuring DHCP Option 43 section on page 20 for more information. Note The access point requires a gigabit Ethernet (GbE) link to prevent the Ethernet port from becoming a bottleneck for traffic because wireless traffic speeds exceed transmit speeds of a 10/100 Ethernet port. Step 2 Apply power to the access point. See Powering the Access Point, page 14. a. As the access point attempts to connect to the controller, the LEDs cycle through a green, red, and amber sequence, which can take up to 5 minutes. Note If the access point remains in this mode for more than five minutes, the access point is unable to find the Master Cisco wireless LAN controller. Check the connection between the access point and the Cisco wireless LAN controller and be sure that they are on the same subnet. If the access point shuts down, check the power source. b. c. After the access point finds the Cisco wireless LAN controller, it attempts to download the new operating system code if the access point code version differs from the Cisco wireless LAN controller code version. While this is happening, the Status LED blinks amber. If the operating system download is successful, the access point reboots. d. Step 3 Configure the access point if required. Use the controller CLI, controller GUI, or Cisco Prime Infrastructure Step 4 Step 5 to customize the access-point-specific 802.11ac network settings. If the pre-installation configuration is successful, the Status LED is green indicating normal operation. Disconnect the access point and mount it at the location at which you intend to deploy it on the wireless network. If your access point does not indicate normal operation, turn it off and repeat the pre-installation configuration. Note When you are installing a Layer 3 access point on a different subnet than the Cisco wireless LAN controller, be sure that a DHCP server is reachable from the subnet on which you will be installing the access point, and that the subnet has a route back to the Cisco wireless LAN controller. Also be sure that the route back to the Cisco wireless LAN controller has destination UDP ports 5246 and 5247 open for CAPWAP communications. Ensure that the route back to the primary, secondary, and tertiary wireless LAN controller allows IP packet fragments. Finally, be sure that if address translation is used, that the access point and the Cisco wireless LAN controller have a static 1-to-1 NAT to an outside address. (Port Address Translation is not supported.) 11 Cisco Catalyst 9117AX Series Access Points D r a f t L a b e l - C i s c o C o n f i d e n t i a l 8 Preparing the AP for Installation Before you mount and deploy your access point, we recommend that you perform a site survey (or use the site planning tool) to determine the best location to install your access point. You should have the following information about your wireless network available:

Access point locations. Access point mounting options: below a suspended ceiling, on a flat horizontal surface, or on a desktop. Note You can mount the access point above a suspended ceiling but you must purchase additional mounting hardware: See Mounting the Access Point section on page 13 for additional information. Access point power options: PoE+ or Cisco Power Injector AIR-PWRINJ5= or AIR-PWRINJ6=. Note If AIR-PWRINJ5= is used, the AP will work with reduced features. Cisco recommends that you make a site map showing access point locations so that you can record the device MAC addresses from each location and return them to the person who is planning or managing your wireless network. 12 Cisco Catalyst 9117AX Series Access Points D r a f t L a b e l - C i s c o C o n f i d e n t i a l 9 Mounting the Access Point Cisco Catalyst 9117AX series access points can be mounted in several configurations on a suspended ceiling, on a hard ceiling or wall, on an electrical or network box, and above a suspended ceiling. For access point mounting instructions, go to the following URL:

http://www.cisco.com/c/en/us/td/docs/wireless/access_point/mounting/guide/apmount.html The standard mounting hardware supported by the AP is listed in Table 1. Table 1 Brackets and Clips for Mounting the AP Brackets1 Part Number AIR-AP-BRACKET-1 Description Low-profile bracket Clips AIR-AP-BRACKET-2 AIR-AP-T-RAIL-R

(This is the default option) Universal bracket Ceiling Grid Clip (Recessed mounting) AIR-AP-T-RAIL-F AIR-CHNL-ADAPTER

(This is the default option) Ceiling Grid Clip (Flush mounting) Optional adapter for channel-rail ceiling grid profile. 1. Mount the AP using no less than four screw holes on a bracket. When mounting the AP in areas where there is a possibility of the AP being knocked off the mounting bracket, use the lock hasp on the back of the AP (see Figure 4) to lock it to the bracket. Figure 4 Locking the AP to the Bracket 1 Position of the hasps for the locks on the back of the 9117AXI and 9117AXE models 13 Cisco Catalyst 9117AX Series Access Points D r a f t L a b e l - C i s c o C o n f i d e n t i a l 10 Powering the Access Point The AP can be powered only through Power-over-Ethernet (PoE) using the following:

802.3at Cisco Power Injector AIR-PWRINJ6=

Note If USB is used with 802.3at power, the AP will work with reduced features. 802.3af Cisco Power Injector AIR-PWRINJ5=

Note If AIR-PWRINJ5= is used, the AP will work with reduced features. Any 802.3at (25.5 W) compliant switch port 11 Configuring and Deploying the Access Point This section describes how to connect the access point to a wireless LAN controller. Because the configuration process takes place on the controller, see the Cisco Wireless LAN Controller Configuration Guide for additional information. The information in this section does not include configuring Link Aggregation. For information on configuring Link Aggregation, see the Cisco Wireless LAN Controller Configuration Guide, Release 8.2, at the following URL:

http://www.cisco.com/c/en/us/td/docs/wireless/controller/8-2/configuration-guide/b_cg82.html The Controller Discovery Process The access point uses standard Control and Provisioning of Wireless Access Points Protocol (CAPWAP) to communicate between the controller and other wireless access points on the network. CAPWAP is a standard, inter-operable protocol which enables an access controller to manage a collection of wireless termination points. The discovery process using CAPWAP is identical to the Lightweight Access Point Protocol (LWAPP) used with previous Cisco Catalyst access points. LWAPP-enabled access points are compatible with CAPWAP, and conversion to a CAPWAP controller is seamless. Deployments can combine CAPWAP and LWAPP software on the controllers. The functionality provided by the controller does not change except for customers who have Layer 2 deployments, which CAPWAP does not support. In a CAPWAP environment, a wireless access point discovers a controller by using CAPWAP discovery mechanisms and then sends it a CAPWAP join request. The controller sends the access point a CAPWAP join response allowing the access point to join the controller. When the access point joins the controller, the controller manages its configuration, firmware, control transactions, and data transactions. Note Note For additional information about the discovery process and CAPWAP, see the Cisco Wireless LAN Controller Software Configuration Guide. This document is available on Cisco.com. CAPWAP support is provided in controller software release 5.2 or later. However, your controller must be running the release that supports 9117AX series access points, as specified in the access point data sheet. 14 Cisco Catalyst 9117AX Series Access Points D r a f t L a b e l - C i s c o C o n f i d e n t i a l Note You cannot edit or query any access point using the controller CLI if the name of the access point contains a space. Note Make sure that the controller is set to the current time. If the controller is set to a time that has already occurred, the access point might not join the controller because its certificate may not be valid for that time. Access points must be discovered by a controller before they can become an active part of the network. The access point supports these controller discovery processes:

Layer 3 CAPWAP discoveryCan occur on different subnets than the access point and uses IP addresses and UDP packets rather than MAC addresses used by Layer 2 discovery. Locally stored controller IP address discoveryIf the access point was previously joined to a controller, the IP addresses of the primary, secondary, and tertiary controllers are stored in the access point non-volatile memory. This process of storing controller IP addresses on an access point for later deployment is called priming the access point. For more information about priming, see the Performing a Pre-Installation Configuration section on page 10. DHCP server discoveryThis feature uses DHCP option 43 to provide controller IP addresses to the access points. Cisco switches support a DHCP server option that is typically used for this capability. For more information about DHCP option 43, see the Configuring DHCP Option 43 section on page 20. DNS discoveryThe access point can discover controllers through your domain name server (DNS). For the access point to do so, you must configure your DNS to return controller IP addresses in response to CISCO-CAPWAP-CONTROLLER.localdomain, where localdomain is the access point domain name. Configuring the CISCO-CAPWAP-CONTROLLER provides backwards compatibility in an existing customer deployment. When an access point receives an IP address and DNS information from a DHCP server, it contacts the DNS to resolve CISCO-CAPWAP-CONTROLLER.localdomain. When the DNS sends a list of controller IP addresses, the access point sends discovery requests to the controllers. Deploying the Access Point on the Wireless Network After you have mounted the access point, follow these steps to deploy it on the wireless network:

Step 1 Connect and power up the access point. Step 2 Observe the access point LED (for LED descriptions, see Checking the Access Point LEDs section on page 17). a. When you power up the access point, it begins a power-up sequence that you can verify by observing the b. c. access point LED. If the power-up sequence is successful, the discovery and join process begins. During this process, the LED blinks sequentially green, red, and off. When the access point has joined a controller, the LED is chirping green if no clients are associated or green if one or more clients are associated. If the LED is not on, the access point is most likely not receiving power. If the LED blinks sequentially for more than 5 minutes, the access point is unable to find its primary, secondary, and tertiary Cisco wireless LAN controller. Check the connection between the access point and the Cisco wireless LAN controller, and be sure the access point and the Cisco wireless LAN controller are either on the same subnet or that the access point has a route back to its primary, secondary, and tertiary Cisco wireless LAN controller. Also, if the access point is not on the same subnet as the Cisco wireless LAN controller, be sure that there is a properly configured DHCP server on the same subnet as the access point. 15 Cisco Catalyst 9117AX Series Access Points D r a f t L a b e l - C i s c o C o n f i d e n t i a l See the Configuring DHCP Option 43 section on page 20 for additional information. Step 3 Reconfigure the Cisco wireless LAN controller so that it is not the Master. Note A Master Cisco wireless LAN controller should be used only for configuring access points and not in a working network. 16 Cisco Catalyst 9117AX Series Access Points D r a f t L a b e l - C i s c o C o n f i d e n t i a l 12 Checking the Access Point LEDs The location of the access point status LED is shown in Figure 2. Note Regarding LED status colors, it is expected that there will be small variations in color intensity and hue from unit to unit. This is within the normal range of the LED manufacturers specifications and is not a defect. The access point status LED indicates various conditions and are described in Table 2. Table 2 LED Status Indications Message Type Association status LED State Green Blue Green Boot loader status Boot loader warning Boot loader error Operating status Access point operating system errors Message Meaning Normal operating condition, but no wireless client associated Normal operating condition, at least one wireless client association Executing boot loader Blinking Green Blinking Blue Alternating between Green and Red Cycling through Red-Off-Green-Off-Blue-Off Cycling through Blue-Red-Green-Off Boot loader signing verification failure Software upgrade in progress Discovery/join process in progress Access point location command invoked from controller web interface. General warning; insufficient inline power 17 Cisco Catalyst 9117AX Series Access Points D r a f t L a b e l - C i s c o C o n f i d e n t i a l 13 Miscellaneous Usage and Configuration Guidelines Using the Mode Button Using the Mode button (see Figure 3) you can:

Reset the AP to the default factory-shipped configuration. Clear the AP internal storage, including all configuration files. To use the mode button, press, and keep pressed, the mode button on the access point during the AP boot cycle. Wait until the AP status LED changes to Amber. During this, the AP console shows a seconds counter, counting the number of seconds the mode button is pressed. Then:

To reset the AP to the default factory-shipped configuration, keep the mode button pressed for less than 20 seconds. The AP configuration files are cleared. This resets all configuration settings to factory defaults, including passwords, WEP keys, the IP address, and the SSID. To clear the AP internal storage, including all configuration files and the regulatory domain configuration, keep the mode button pressed for more than 20 seconds, but less than 60 seconds. The AP status LED changes from Amber to Red, and all the files in the AP storage directory are cleared. If you keep the mode button pressed for more than 60 seconds, the mode button is assumed faulty and no changes are made. Troubleshooting the Access Point to Cisco Controller Join Process Note Ensure that your controller is running the latest Cisco Wireless Controller Software Release as specified in the access point data sheet. Access points can fail to join a controller for many reasons: a RADIUS authorization is pending; self-signed certificates are not enabled on the controller; the access point and the controller regulatory domains dont match, and so on. Controller software enables you to configure the access points to send all CAPWAP-related errors to a syslog server. You do not need to enable any debug commands on the controller because all of the CAPWAP error messages can be viewed from the syslog server itself. The state of the access point is not maintained on the controller until it receives a CAPWAP join request from the access point. Therefore, it can be difficult to determine why the CAPWAP discovery request from a certain access point was rejected. In order to troubleshoot such joining problems without enabling CAPWAP debug commands on the controller, the controller collects information for all access points that send a discovery message to it and maintains information for any access points that have successfully joined it. The controller collects all join-related information for each access point that sends a CAPWAP discovery request to the controller. Collection begins with the first discovery message received from the access point and ends with the last configuration payload sent from the controller to the access point. You can view join-related information for up to three times the maximum number of access points supported by the platform for the 2500 series controllers and the Controller Network Module within the Cisco 28/37/28xx Series Integrated Services Routers. 18 Cisco Catalyst 9117AX Series Access Points D r a f t L a b e l - C i s c o C o n f i d e n t i a l Note The maximum number of access points varies for the Cisco WiSM2, depending on which controller software release is being used. When the controller is maintaining join-related information for the maximum number of access points, it does not collect information for any more access points. An access point sends all syslog messages to IP address 255.255.255.255 by default when any of the following conditions are met:

An access point running software release 8.2.110.0 or later has been newly deployed. An existing access point running software release 8.2.110.0 or later has been reset after clearing the configuration. If any of these conditions are met and the access point has not yet joined a controller, you can also configure a DHCP server to return a syslog server IP address to the access point using option 7 on the server. The access point then starts sending all syslog messages to this IP address. When the access point joins a controller for the first time, the controller sends the global syslog server IP address (the default is 255.255.255.255) to the access point. After that, the access point sends all syslog messages to this IP address until it is overridden by one of the following scenarios:

The access point is still connected to the same controller, and the global syslog server IP address configuration on the controller has been changed using the config ap syslog host global syslog_server_IP_address command. In this case, the controller sends the new global syslog server IP address to the access point. The access point is still connected to the same controller, and a specific syslog server IP address has been configured for the access point on the controller using the config ap syslog host specific Cisco_AP syslog_server_IP_address command. In this case, the controller sends the new specific syslog server IP address to the access point. The access point is disconnected from the controller and joins another controller. In this case, the new controller sends its global syslog server IP address to the access point. Whenever a new syslog server IP address overrides the existing syslog server IP address, the old address is erased from persistent storage, and the new address is stored in its place. The access point also starts sending all syslog messages to the new IP address provided the access point can reach the syslog server IP address. You can configure the syslog server for access points and view the access point join information only from the controller CLI. Important Information for Controller-based Deployments Keep these guidelines in mind when you use 9117AX series access point:

The access point can only communicate with Cisco wireless LAN controllers. The access point does not support Wireless Domain Services (WDS) and cannot communicate with WDS devices. However, the controller provides functionality equivalent to WDS when the access point joins it. CAPWAP does not support Layer 2. The access point must get an IP address and discover the controller using Layer 3, DHCP, DNS, or IP subnet broadcast. The access point console port is enabled for monitoring and debug purposes. All configuration commands are disabled when the access point is connected to a controller. 19 Cisco Catalyst 9117AX Series Access Points D r a f t L a b e l - C i s c o C o n f i d e n t i a l Configuring DHCP Option 43 You can use DHCP Option 43 to provide a list of controller IP addresses to the access points, enabling them to find and join a controller. The following is a DHCP Option 43 configuration example on a Windows 2003 Enterprise DHCP server for use with Cisco Catalyst lightweight access points. For other DHCP server implementations, consult product documentation for configuring DHCP Option 43. In Option 43, you should use the IP address of the controller management interface. Note DHCP Option 43 is limited to one access point type per DHCP pool. You must configure a separate DHCP pool for each access point type. The 9117AX series access point uses the type-length-value (TLV) format for DHCP Option 43. DHCP servers must be programmed to return the option based on the access point DHCP Vendor Class Identifier (VCI) string (DHCP Option 43). The VCI string for the 9117AX series access point is:

Cisco AP c9117AX The format of the TLV block is listed below:

Type0xf1 (decimal 241) LengthNumber of controller IP addresses * 4 ValueIP addresses of the WLC management interfaces listed sequentially in hex To configure DHCP Option 43 in the embedded Cisco IOS DHCP server, follow these steps:

Enter configuration mode at the Cisco IOS CLI. Step 1 Step 2 Create the DHCP pool, including the necessary parameters such as default router and name server. A DHCP scope example is as follows:

ip dhcp pool <pool name>

network <IP Network> <Netmask>

default-router <Default router>

dns-server <DNS Server>

Where:

<pool name> is the name of the DHCP pool, such as AP9117AX

<IP Network> is the network IP address where the controller resides, such as 10.0.15.1

<Netmask> is the subnet mask, such as 255.255.255.0

<Default router> is the IP address of the default router, such as 10.0.0.1

<DNS Server> is the IP address of the DNS server, such as 10.0.10.2 Step 3 Add the option 43 line using the following syntax:

option 43 hex <hex string>

The hex string is assembled by concatenating the TLV values shown below:

Type + Length + Value For example, suppose that there are two controllers with management interface IP addresses, 10.126.126.2 and 10.127.127.2. The type is f1(hex). The length is 2 * 4 = 8 = 08 (hex). The IP addresses translate to 0a7e7e02 and 0a7f7f02. Assembling the string then yields f1080a7e7e020a7f7f02. The resulting Cisco IOS command added to the DHCP scope is option 43 hex f1080a7e7e020a7f7f02. 20 Cisco Catalyst 9117AX Series Access Points D r a f t L a b e l - C i s c o C o n f i d e n t i a l 14 FAQs What is 802.11ax?

The IEEE 802.11ax standard, also known as the High-Efficiency-Wireless (HEW), builds off of the 802.11ac and delivers a better experience in typical environments, and a more predictable performance for advanced applications such as 4K or 8K video, high-density high-definition collaboration applications, all-wireless offices and Internet-of-Things (IoT). 802.11ax is designed to use both 2.4Ghz and the 5GHz bands, unlike prior standards. How Does Auto-Link Aggregation work with the 9117AX?

The 9117AX AP supports automatic Link Aggregation (LAG) across its Ethernet and AUX ports. This provides up to 2 Gbps of uplink speed to the access point. The following Cisco switching series support LAG with the 9117AX AP:

Catalyst 3850 / all models (non-CA mode) Catalyst 3650 / all models (non-CA mode) Catalyst 4500/Sup-8E Catalyst 6500/Sup 720 or newer What is a ClientLink 4.0? How is it different from Tx-Beamforming?

Cisco ClientLink 4.0 is a beamforming capability built into Cisco Catalyst wireless LAN access points. When the access point concentrates signals toward the receiving client, that client is better able to hear the APs transmission, and so throughput is greater. ClientLink also enhances performance in the uplink (client-to-AP) direction, so that the AP can also better hear the client communications. The result is improved performance in both directions, and doesnt require any special capabilities in the client device to work. ClientLink works with all client technologies. It makes sure each client type always operates at the best possible rate, as determined by the 802.11 access technology supported, network conditions, and the distance of the client from the Wi-Fi AP. ClientLink helps maintain maximum client rates. Can the USB port be used?

The USB port has software support for certain dongles. 21 Cisco Catalyst 9117AX Series Access Points D r a f t L a b e l - C i s c o C o n f i d e n t i a l 15 Related Documentation All user documentation for the Cisco Catalyst 9117AX series access point is available at the following URL:

http://www.cisco.com/c/en/us/support/wireless/aironet-9117AX-series-access-points/tsd-products-support-series-

home.html For detailed information and guidelines for configuring and deploying your access point in a wireless network, see the following documentation:

Cisco Wireless LAN Controller Configuration Guide, Release 8.9, at the following URL:

http://www.cisco.com/c/en/us/td/docs/wireless/controller/8-9/config-guide/b_cg89.html Cisco Catalyst 9117AX Series Access Point Deployment Guide, at the following URL:

<URL to be added at CCO>

22 Cisco Catalyst 9117AX Series Access Points D r a f t L a b e l - C i s c o C o n f i d e n t i a l 16 Declarations of Conformity and Regulatory Information This section provides declarations of conformity and regulatory information for the Cisco Catalyst 9117AX Series Access Points. You can find additional information at this URL:

www.cisco.com/go/aironet/compliance Manufacturers Federal Communication Commission Declaration of Conformity Statement Tested To Comply With FCC Standards FOR HOME OR OFFICE USE Certification Number LDKHDGWI1903 Access Point Models C9117AXI-B Manufacturer:

Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA This device complies with Part 15 rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and radiates radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference. However, there is no guarantee that interference will not occur. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from which the receiver is connected. Consult the dealer or an experienced radio/TV technician. 23 Cisco Catalyst 9117AX Series Access Points D r a f t L a b e l - C i s c o C o n f i d e n t i a l Caution The Part 15 radio device operates on a non-interference basis with other devices operating at this frequency when using the integrated antennas. Any changes or modification to the product not expressly approved by Cisco could void the users authority to operate this device. VCCI Statement for Japan Warning This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual. 24 Cisco Catalyst 9117AX Series Access Points D r a f t L a b e l - C i s c o C o n f i d e n t i a l Guidelines for Operating Cisco Catalyst Access Points in Japan This section provides guidelines for avoiding interference when operating Cisco Catalyst access points in Japan. These guidelines are provided in both Japanese and English. Japanese Translation 03-6434-6500 7 9 6 8 0 2 English Translation This equipment operates in the same frequency bandwidth as industrial, scientific, and medical devices such as microwave ovens and mobile object identification (RF-ID) systems (licensed premises radio stations and unlicensed specified low-power radio stations) used in factory production lines. 1. Before using this equipment, make sure that no premises radio stations or specified low-power radio stations of RF-ID are used in the vicinity. 2. If this equipment causes RF interference to a premises radio station of RF-ID, promptly change the frequency or stop using the device; contact the number below and ask for recommendations on avoiding radio interference, such as setting partitions. 3. If this equipment causes RF interference to a specified low-power radio station of RF-ID, contact the number below. Contact Number: 03-6434-6500 25 Cisco Catalyst 9117AX Series Access Points D r a f t L a b e l - C i s c o C o n f i d e n t i a l Industry Canada Access Point Models C9117AXI-A Certification Number 2461N-HDGWI1903 Canadian Compliance Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. This radio transmitter has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le prsent metteur radio a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal et l'impdance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. Antenna Type Dual-band Omni Dual-band Dipole Dual-Band Directional Antenna Gain 2/4 dBi 2/4 dBi 6/6 dBi Antenna Impedance 50 ohms 50 ohms 50 ohms Operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. La bande 5 150-5 250 MHz est rservs uniquement pour une utilisation l'intrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux. Users are advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Les utilisateurs tes aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux

(c.--d., qu'ils ont la priorit) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. 26 Cisco Catalyst 9117AX Series Access Points D r a f t L a b e l - C i s c o C o n f i d e n t i a l European Community, Switzerland, Norway, Iceland, and Liechtenstein Access Point Models:

C9117AXI-E C9117AXE-E 27 Cisco Catalyst 9117AX Series Access Points D r a f t L a b e l - C i s c o C o n f i d e n t i a l Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC &

Medical Directive 93/42/EEC 28 Cisco Catalyst 9117AX Series Access Points D r a f t L a b e l - C i s c o C o n f i d e n t i a l The following standards were applied:

EMCEN 301.489-1 v1.9.2; EN 301.489-17 v2.2.1 Health & SafetyEN60950-1: 2006; EN 50285: 2002 RadioEN 300 328 v 1.8.1; EN 301.893 v 1.7.1 The conformity assessment procedure referred to in Article 10.4 and Annex III of Directive 1999/5/EC has been followed. This device also conforms to the EMC requirements of the Medical Devices Directive 93/42/EEC. Note This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation. For more details, contact Cisco Corporate Compliance. 29 Cisco Catalyst 9117AX Series Access Points D r a f t L a b e l - C i s c o C o n f i d e n t i a l The product carries the CE Mark:

Declaration of Conformity for RF Exposure This section contains information on compliance with guidelines related to RF exposure. Generic Discussion on RF Exposure The Cisco products are designed to comply with the following national and international standards on Human Exposure to Radio Frequencies:

US 47 Code of Federal Regulations Part 2 Subpart J American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers / IEEE C 95.1 (99) International Commission on Non Ionizing Radiation Protection (ICNIRP) 98 Ministry of Health (Canada) Safety Code 6. Limits on Human Exposure to Radio Frequency Fields in the range from 3kHz to 300 GHz Australia Radiation Protection Standard To ensure compliance with various national and international Electromagnetic Field (EMF) standards, the system should only be operated with Cisco approved antennas and accessories. This Device Meets International Guidelines for Exposure to Radio Waves The 9117AX series device includes a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves (radio frequency electromagnetic fields) recommended by international guidelines. The guidelines were developed by an independent scientific organization (ICNIRP) and include a substantial safety margin designed to ensure the safety of all persons, regardless of age and health. As such the systems are designed to be operated as to avoid contact with the antennas by the end user. It is recommended to set the system in a location where the antennas can remain at least a minimum distance as specified from the user in accordance to the regulatory guidelines which are designed to reduce the overall exposure of the user or operator. Separation Distance MPE 0.6 mW/cm2 Distance 30 cm (12 inches) Limit 1.00 mW/cm2 The World Health Organization has stated that present scientific information does not indicate the need for any special precautions for the use of wireless devices. They recommend that if you are interested in further reducing your exposure then you can easily do so by reorienting antennas away from the user or placing he antennas at a greater separation distance then recommended. 30 Cisco Catalyst 9117AX Series Access Points D r a f t L a b e l - C i s c o C o n f i d e n t i a l This Device Meets FCC Guidelines for Exposure to Radio Waves The 9117AX series device includes a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves (radio frequency electromagnetic fields) as referenced in FCC Part 1.1310. The guidelines are based on IEEE ANSI C 95.1 (92) and include a substantial safety margin designed to ensure the safety of all persons, regardless of age and health. As such the systems are designed to be operated as to avoid contact with the antennas by the end user. It is recommended to set the system in a location where the antennas can remain at least a minimum distance as specified from the user in accordance to the regulatory guidelines which are designed to reduce the overall exposure of the user or operator. The device has been tested and found compliant with the applicable regulations as part of the radio certification process. Separation Distance MPE 0.6 mW/cm2 Distance 30 cm (12 inches) Limit 1.00 mW/cm2 The US Food and Drug Administration has stated that present scientific information does not indicate the need for any special precautions for the use of wireless devices. The FCC recommends that if you are interested in further reducing your exposure then you can easily do so by reorienting antennas away from the user or placing the antennas at a greater separation distance then recommended or lowering the transmitter power output. This Device Meets the Industry Canada Guidelines for Exposure to Radio Waves The 9117AX series device includes a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves (radio frequency electromagnetic fields) as referenced in Health Canada Safety Code 6. The guidelines include a substantial safety margin designed into the limit to ensure the safety of all persons, regardless of age and health. As such the systems are designed to be operated as to avoid contact with the antennas by the end user. It is recommended to set the system in a location where the antennas can remain at least a minimum distance as specified from the user in accordance to the regulatory guidelines which are designed to reduce the overall exposure of the user or operator. Frequency 2.4 GHz 5 GHz MPE 1.89 W/m2 2.73 W/m2 Separation Distance Distance 30 cm (12 inches) Limit 5.4 W/m2 9.2 W/m2 Health Canada states that present scientific information does not indicate the need for any special precautions for the use of wireless devices. They recommend that if you are interested in further reducing your exposure you can easily do so by reorienting antennas away from the user, placing the antennas at a greater separation distance than recommended, or lowering the transmitter power output. 31 Cisco Catalyst 9117AX Series Access Points D r a f t L a b e l - C i s c o C o n f i d e n t i a l Cet appareil est conforme aux directives internationales en matire d'exposition aux frquences radiolectriques Cet appareil de la gamme 9117AX comprend un metteur-rcepteur radio. Il a t conu de manire respecter les limites en matire d'exposition aux frquences radiolectriques (champs lectromagntiques de frquence radio), recommandes dans le code de scurit 6 de Sant Canada. Ces directives intgrent une marge de scurit importante destine assurer la scurit de tous, indpendamment de l'ge et de la sant. Par consquent, les systmes sont conus pour tre exploits en vitant que l'utilisateur n'entre en contact avec les antennes. Il est recommand de poser le systme l o les antennes sont une distance minimale telle que prcise par l'utilisateur conformment aux directives rglementaires qui sont conues pour rduire l'exposition gnrale de l'utilisateur ou de l'oprateur. Frquence 2.4 GHz 5 GHz Distance d'loignement Distance 30 cm (12 inches) MPE 1.89 W/m2 2.73 W/m2 Limite 5.4 W/m2 9.2 W/m2 Sant Canada affirme que la littrature scientifique actuelle n'indique pas qu'il faille prendre des prcautions particulires lors de l'utilisation d'un appareil sans fil. Si vous voulez rduire votre exposition encore davantage, selon l'agence, vous pouvez facilement le faire en rorientant les antennes afin qu'elles soient diriges l'cart de l'utilisateur, en les plaant une distance d'loignement suprieure celle recommande ou en rduisant la puissance de sortie de l'metteur. Additional Information on RF Exposure You can find additional information on the subject at the following links:

Cisco Systems Spread Spectrum Radios and RF Safety white paper at this URL:

http://www.cisco.com/warp/public/cc/pd/witc/ao340ap/prodlit/rfhr_wi.htm FCC Bulletin 56: Questions and Answers about Biological Effects and Potential Hazards of Radio Frequency Electromagnetic Fields FCC Bulletin 65: Evaluating Compliance with the FCC guidelines for Human Exposure to Radio Frequency Electromagnetic Fields You can obtain additional information from the following organizations:

World Health Organization Internal Commission on Non-Ionizing Radiation Protection at this URL: www.who.int/emf United Kingdom, National Radiological Protection Board at this URL: www.nrpb.org.uk Cellular Telecommunications Association at this URL: www.wow-com.com The Mobile Manufacturers Forum at this URL: www.mmfai.org 32 Cisco Catalyst 9117AX Series Access Points D r a f t L a b e l - C i s c o C o n f i d e n t i a l Administrative Rules for Cisco Catalyst Access Points in Taiwan This section provides administrative rules for operating Cisco Catalyst access points in Taiwan. The rules for all access points are provided in both Chinese and English. Chinese Translation English Translation Administrative Rules for Low-power Radio-Frequency Devices Article 12 For those low-power radio-frequency devices that have already received a type-approval, companies, business units or users should not change its frequencies, increase its power or change its original features and functions. Article 14 The operation of the low-power radio-frequency devices is subject to the conditions that no harmful interference is caused to aviation safety and authorized radio station; and if interference is caused, the user must stop operating the device immediately and can't re-operate it until the harmful interference is clear. The authorized radio station means a radio-communication service operating in accordance with the Communication Act. The operation of the low-power radio-frequency devices is subject to the interference caused by the operation of an authorized radio station, by another intentional or unintentional radiator, by industrial, scientific and medical (ISM) equipment, or by an incidental radiator. 33 Chinese Translation English Translation Low-power Radio-frequency Devices Technical Specifications 4.7 4.7.5 4.7.6 4.7.7 Unlicensed National Information Infrastructure Within the 5.25-5.35 GHz band, U-NII devices will be restricted to indoor operations to reduce any potential for harmful interference to co-channel MSS operations. The U-NII devices shall accept any interference from legal communications and shall not interfere the legal communications. If interference is caused, the user must stop operating the device immediately and can't re-operate it until the harmful interference is clear. Manufacturers of U-NII devices are responsible for ensuring frequency stability such that an emission is maintained within the band of operation under all conditions of normal operation as specified in the user manual. D r a f t L a b e l - C i s c o C o n f i d e n t i a l Cisco Catalyst 9117AX Series Access Points Communications, Services, and Additional Information Operation of Cisco Catalyst Access Points in Brazil This section contains special information for operation of Cisco Catalyst access points in Brazil. Access Point Models:

C9117AXI-Z C9117AXE-Z Figure 5 Brazil Regulatory Information Portuguese Translation Este equipamento no tem direito proteo contra interferncia prejudicial e no pode causar interferncia em sistemas devidamente autorizados. English Translation This equipment is not entitled to the protection from harmful interference and may not cause interference with duly authorized systems. Declaration of Conformity Statements All the Declaration of Conformity statements related to this product can be found at the following location:

http://www.ciscofax.com Communications, Services, and Additional Information To receive timely, relevant information from Cisco, sign up at Cisco Profile Manager. To get the business impact youre looking for with the technologies that matter, visit Cisco Services. To submit a service request, visit Cisco Support. 35 D r a f t L a b e l - C i s c o C o n f i d e n t i a l Cisco Catalyst 9117AX Series Access Points Cisco Bug Search Tool To discover and browse secure, validated enterprise-class apps, products, solutions and services, visit Cisco Marketplace. To obtain general networking, training, and certification titles, visit Cisco Press. To find warranty information for a specific product or product family, access Cisco Warranty Finder. Cisco Bug Search Tool Cisco Bug Search Tool (BST) is a web-based tool that acts as a gateway to the Cisco bug tracking system that maintains a comprehensive list of defects and vulnerabilities in Cisco products and software. BST provides you with detailed defect information about your products and software. Communications, Services, and Additional Information To receive timely, relevant information from Cisco, sign up at Cisco Profile Manager. To get the business impact youre looking for with the technologies that matter, visit Cisco Services. To submit a service request, visit Cisco Support. To discover and browse secure, validated enterprise-class apps, products, solutions and services, visit Cisco Marketplace. To obtain general networking, training, and certification titles, visit Cisco Press. To find warranty information for a specific product or product family, access Cisco Warranty Finder. Cisco Bug Search Tool Cisco Bug Search Tool (BST) is a web-based tool that acts as a gateway to the Cisco bug tracking system that maintains a comprehensive list of defects and vulnerabilities in Cisco products and software. BST provides you with detailed defect information about your products and software. 2019 Cisco Systems, Inc. All rights reserved. Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL:

www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1721R) 36

 

 

Custom EMC Test Report No: EDCS 15634526 Test Report Cisco C9117AXI-X Cisco C9117AXI-T

(X=A,B,N) Cisco Catalyst 802.11ax Access Point FCC ID: LDKHDGWI1903 IC: 2461N-HDGWI1903 2400-2483.5 MHz Against the following Specifications:

CFR47 Part 15.247 RSS-247 RSS-Gen LP0002 (2018-01-10) Cisco Systems 170 West Tasman Drive San Jose, CA 95134 Author: Chris Blair, Allan Beecroft Tested By: Chris Blair Approved By: Allan Beecroft Title: Technical Manager Revision: Controlled by Doc Central This report replaces any previously entered test report under EDCS 15634526.This test report has been electronically authorized and archived using the CISCO Engineering Document Control system. Test Report Template EDCS# 11644121. Page No: 1 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 SECTION 1: OVERVIEW ......................................................................................................................................... 3 SECTION 2: ASSESSMENT INFORMATION ....................................................................................................... 4 2.1 GENERAL ............................................................................................................................................................. 4 2.2 DATE OF TESTING ................................................................................................................................................ 6 2.3 REPORT ISSUE DATE ............................................................................................................................................ 6 2.4 TESTING FACILITIES ............................................................................................................................................. 6 2.5 EQUIPMENT ASSESSED (EUT) ............................................................................................................................. 6 2.6 EUT DESCRIPTION ............................................................................................................................................... 7 SECTION 3: RESULT SUMMARY .......................................................................................................................... 9 3.1 RESULTS SUMMARY TABLE ................................................................................................................................. 9 SECTION 4: SAMPLE DETAILS ........................................................................................................................... 11 4.1 SAMPLE DETAILS ............................................................................................................................................... 11 4.2 SYSTEM DETAILS ............................................................................................................................................... 11 4.3 MODE OF OPERATION DETAILS ......................................................................................................................... 11 APPENDIX A: CONDUCTED EMISSION TEST RESULTS .............................................................................. 12 CONDUCTED TEST SETUP DIAGRAM ........................................................................................................................ 12 TARGET MAXIMUM CHANNEL POWER .................................................................................................................... 12 A.1 DUTY CYCLE .................................................................................................................................................... 13 A.2 DTS BANDWIDTH (6DB BANDWIDTH) .............................................................................................................. 17 A.3 OCCUPIED BANDWIDTH .................................................................................................................................... 21 A.4 MAXIMUM CONDUCTED OUTPUT POWER ......................................................................................................... 25 A.5 POWER SPECTRAL DENSITY .............................................................................................................................. 31 A.6 CONDUCTED SPURIOUS EMISSIONS ................................................................................................................... 35 A.7 CONDUCTED BANDEDGE (RESTRICTED BAND) ................................................................................................. 46 A.8 CONDUCTED BANDEDGE (NON-RESTRICTED BAND) ........................................................................................ 56 APPENDIX B:

RADIATED EMISSION TEST RESULTS ........................................................................... 60 APPENDIX C:

LIST OF TEST EQUIPMENT USED TO PERFORM THE TEST .................................... 61 APPENDIX D: ABBREVIATION KEY AND DEFINITIONS ...................................................................... 62 APPENDIX E:

PHOTOGRAPHS OF TEST SETUPS ................................................................................... 62 SOFTWARE USED TO PERFORM TESTING ................................................................... 64 APPENDIX F:

TEST PROCEDURES ............................................................................................................. 64 APPENDIX G:

APPENDIX H:

SCOPE OF ACCREDITATION (A2LA CERTIFICATE NUMBER 1178-01) ................. 64 APPENDIX I:

TEST ASSESSMENT PLAN .................................................................................................. 65 APPENDIX J: WORST CASE JUSTIFICATION ............................................................................................... 65 APPENDIX K: UUT SOFTWARE INFO FROM CLI .......................................................................................... 65 Page No: 2 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 Section 1: Overview The samples were assessed against the tests under the requirements of the following specifications:

Emission CFR47 Part 15.247 RSS-247 Issue 2: Feb 2017 RSS-Gen Issue 5: Apr 2018 LP0002 (2018-01-10) Page No: 3 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 Section 2: Assessment Information 2.1 General This report contains an assessment of an apparatus against Electromagnetic Compatibility Standards based upon tests carried out on the samples submitted. The testing was performed by and for the use of Cisco systems Inc:

With regard to this assessment, the following points should be noted:

a) The results contained in this report relate only to the items tested and were obtained in the period between the date of the initial assessment and the date of issue of the report. Manufactured products will not necessarily give identical results due to production and measurement tolerances. The apparatus was set up and exercised using the configuration and modes of operation defined in this report only. Where relevant, the apparatus was only assessed using the susceptibility criteria defined in this report and the Test Assessment Plan (TAP). All testing was performed under the following environmental conditions:

Temperature 15C to 35C (54F to 95F) Atmospheric Pressure 860mbar to 1060mbar (25.4" to 31.3") Humidity 10% to 75*%

b) c) d) e) All AC testing was performed at one or more of the following supply voltages:

110V 60 Hz (+/-20%) Emission level [dBuV] = Indicated voltage level [dBuV] + Cable Loss [dB] + Other correction factors [dB]

Units of Measurement The units of measurements defined in the appendices are reported in specific terms, which are test dependent. Where radiated measurements are concerned these are defined at a particular distance. Basic voltage measurements are defined in units of [dBuV]

As an example, the basic calculation for all measurements is as follows:

The combinations of correction factors are dependent upon the exact test configurations [see test equipment lists for further details] and may include:-

Note: to convert the results from dBuV/m to uV/m use the following formula:-

Level in uV/m = Common Antilogarithm [(X dBuV/m)/20] = Y uV/m Antenna Factors, Pre Amplifier Gain, LISN Loss, Pulse Limiter Loss and Filter Insertion Loss.. Page No: 4 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 Measurement Uncertainty Values voltage and power measurements 2 dB conducted EIRP measurements radiated measurements 1.4 dB 3.2 dB frequency measurements 2.4 10-7 temperature measurements humidity measurements 0.54 2.3%

DC and low frequency measurements 2.5%

Where relevant measurement uncertainty levels have been estimated for tests performed on the apparatus. This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. Radiated emissions (expanded uncertainty, confidence interval 95%) 30 MHz - 300 MHz 300 MHz - 1000 MHz 1 GHz - 10 GHz 10 GHz - 18GHz 18GHz - 26.5GHz 26.5GHz - 40GHz

+/- 3.8 dB

+/- 4.3 dB

+/- 4.0 dB

+/- 8.2 dB

+/- 4.1 dB

+/- 3.9 dB 30 MHz 40GHz Conducted emissions (expanded uncertainty, confidence interval 95%) A product is considered to comply with a requirement if the nominal measured value is below the limit line. The product is considered to not be in compliance in case the nominal measured value is above the limit line. This report must not be reproduced except in full, without written approval of Cisco Systems.

+/- 0.38 dB Page No: 5 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 2.2 Date of testing 09-Nov-18 - 20-Nov-18 (conducted tests) 2.3 Report Issue Date 20-Dec-2018 Cisco uses an electronic system to issue, store and control the revision of test reports. This system is called the Engineering Document Control System (EDCS). The actual report issue date is embedded into the original file on EDCS. Any copies of this report, either electronic or paper, that are not on EDCS must be considered uncontrolled. 2.4 Testing facilities This assessment was performed by: Chris Blair Testing Laboratory Cisco Systems, Inc. 125 West Tasman Drive (Building P) San Jose, CA 95134 USA Headquarters Cisco Systems, Inc., 170 West Tasman Drive San Jose, CA 95134, USA Registration Numbers for Industry Canada Cisco System Site Building P, 10m Chamber Building P, 5m Chamber Building I, 5m Chamber Address 125 West Tasman Dr San Jose, CA 95134 125 West Tasman Dr San Jose, CA 95134 285 W. Tasman Drive San Jose, California 95134 Site Identifier Company #: 2461N-2 Company #: 2461N-1 Company #: 2461M-1 Building 7, 5m Chamber 425 E. Tasman Drive Company #: 2461N-3 San Jose, California 95134 Test Engineers Chris Blair 2.5 Equipment Assessed (EUT) Cisco C9117AXI-X Page No: 6 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 2.6 EUT Description The C9117AXI is a dual-band 802.11ax wireless access point w/ BLE, supporting the following WLAN modes:

802.11b (1-11Mbps) 802.11g (6-54Mbps) 802.11n (MCS0-MCS31) 802.11ax (MCS0-MCS11) 802.11a (6-54Mbps) 802.11n (MCS0-MCS31) 802.11ac (MCS0-MCS9) 802.11ax (MCS0-MCS11) and using the following bands: 2400MHz 2483.5MHz 5150MHz 5250MHz 5250MHz 5350MHz 5470MHz 5725MHz. The following antennas are supported by this product. Frequency HOSTPID|

Part Number Please align Host(s) with antenna(s) ANTENNA PID|Part Number Antenna Type Antenna Gain

(includes antenna cable loss) Antenna + Host | Max Antenna Gain | (EIRP) Antenna +

Host | >30 degree 5 GHz Antenna Gain |

(dBi) 2.4GHz&5 GHz TX/RX:

Internal

(ANTA:WIFI 2.4GHz&5 GHz) singleport, dualband omni 2.4GHz&5 GHz TX/RX:

Internal

(ANTB:WIFI 2.4GHz&5 GHz) singleport, dualband omni 2.4GHz&5 GHz TX/RX:

Internal 2.4GHz&5 GHz TX/RX:

Interna

(ANTC:WIFI 2.4GHz&5 GHz) singleport, dualband omni

(ANTD:WIFI 2.4GHz/BLE 2.4GHz&5 GHz) singleport, dualband omni Page No: 7 of 69 2.4GHzWiFi 1path:17dBm+0dB+

3.5dBi=20.5dBm 5GHzWiFi 1path:17dBm+0dB+

4.5dBi=21.5dBm 2.4GHzWiFi 1path:17dBm+0dB+

3.5dBi=20.5dBm 5GHzWiFi 1path:17dBm+0dB+

1path:17dBm+0dB+4dBi 1path:17dBm+0dB+

6dBi=23dBm 2.4GHzWiFi

=21dBm 5GHzWiFi 6dBi=23dBm 2.4GHzBLE

=8.5dBm 2.4GHzWiFi 1path:5dBm+0dB+3.5dBi 2.4GHz:3.5 5GHz:4.5 dBi dB 2.4GHz:3.5 dBi 5GHz:6dBi 2.4GHz:4 dBi 5GHz:6dBi 2.4GHz:3.5 dBi 5GHz:5dBi 1path:17dBm+0dB+

This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 3.5dBi=20.5dBm 5GHzWiFi 1path:17dBm+0dB+

5dBi=22dBm This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Page No: 8 of 69 Custom EMC Test Report No: EDCS 15634526 Section 3: Result Summary 3.1 Results Summary Table Conducted emissions Basic Standard FCC 15.247 RSS-247 LP0002

(2018-01-10)

(3.10.1.6) (2)(A) FCC 15.247 RSS-247 Technical Requirements / Details 6dB Bandwidth Systems using digital modulation techniques may operate in the 2400-2483.5MHz band. The minimum 6dB bandwidth shall be at least 500 kHz 99% & 26 dB Bandwidth:

The 99% occupied bandwidth is the frequency bandwidth such that, below its lower and above its upper frequency limits, the mean powers are each equal to 0.5% of the total mean power of the given emission. There is no limit for 99% OBW. The 26 dB emission is the width of the emission that is constrained by the frequencies associated with the two outermost amplitude points (upper and lower frequencies) that are attenuated by 26 dB relative to the maximum level measured in the fundamental emission. Output Power:

15.247 The maximum conducted output power of the intentional radiator for systems using digital modulation in the 2400-2483.5 MHz band shall not exceed 1 Watt (30dBm). If transmitting antennas of directional gain greater than 6 dBi are used, the maximum conducted output power shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. RSS-247 For DTSs employing digital modulation techniques operating in the band 2400-2483.5 MHz, the maximum peak conducted output power shall not exceed 1W. Except as provided in Section 5.4(e), the e.i.r.p. shall not exceed 4 W. Power Spectral Density For digitally modulated systems, the power spectral density conducted from the intentional radiator to the antenna shall not be greater than 8 dBm in any 3 kHz band during any time interval of continuous transmission. Conducted Spurious Emissions / Band-Edge:

In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated device is operating, the RF power that is produced shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided that the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of root-mean-square averaging over a time interval, as permitted under section 5.4(d), the attenuation required shall be 30 dB instead of 20 dB. Attenuation below the general field strength limits specified in RSS-Gen is not required. Result Pass Pass Pass Pass Pass FCC 15.247 RSS-247 LP0002

(2018-01-10)

(3.10.1.2) (1) (C) FCC 15.247 RSS-247 LP0002

(2018-01-10)

(3.10.1.6) (2) (B) FCC 15.247 RSS-247 LP0002

(2018-01-10)

(3.10.1.5) 2.8 Page No: 9 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 FCC 15.247 RSS-247 FCC 15.205 RSS-Gen Restricted band:

Unwanted emissions falling within the restricted bands, as defined in FCC 15.205 (a) and RSS-Gen 8.10 must also comply with the radiated emission limits specified in FCC 15.209 (a) and RSS-Gen 8.9 Radiated Emissions (General requirements) Basic Standard FCC 15.209 RSS-Gen LP0002

(2018-01-10)

(3.10.1.5) 2.8 Technical Requirements / Details TX Spurious Emissions: Except as provided elsewhere in this subpart, the emissions from an intentional radiator shall not exceed the field strength levels specified in the filed strength limits table in this section. Unwanted emissions falling within the restricted bands, as defined in FCC 15.205 (a) and RSS-Gen 8.10 must also comply with the radiated emission limits specified in FCC 15.209 (a) and RSS-Gen 8.9 RX Spurious Emissions:

RSS-Gen 8.9 Except when the requirements applicable to a given device state otherwise, emissions from licence-exempt transmitters shall comply with the field strength limits shown in Table 4 and Table 5 below. Additionally, the level of any transmitter emission shall not exceed the level of the transmitters fundamental emission. RSS-Gen 8.10 Restricted Bands Unwanted emissions that fall into restricted bands of Table 6 shall comply with the limits specified in RSS-Gen; and (c ) Unwanted emissions that do not fall within the restricted frequency bands of Table 6 shall comply either with the limits specified in the applicable RSS or with those specified in this RSS-Gen. AC conducted Emissions: Except when the requirements applicable to a given device state otherwise, for any radio apparatus equipped to operate from the public utility AC power supply, either directly or indirectly (such as with a battery charger), the radio frequency voltage of emissions conducted back onto the AC power lines in the frequency range of 0.15 MHz to 30 MHz shall not exceed the limits shown in the table in these sections. The more stringent limit applies at the frequency range boundaries. RSS-Gen LP0002

(2018-01-10)

(3.10.1.5) 2.8 FCC 15.207 RSS-Gen LP0002

(2018-01-10) 2.3 Pass Result Tested at BACL Tested at BACL Tested at BACL This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Page No: 10 of 69 Custom EMC Test Report No: EDCS 15634526 Section 4: Sample Details Note: Each sample was evaluated to ensure that its condition was suitable to be used as a test sample prior to the commencement of testing. 4.1 Sample Details Hardware Firmware Rev. P3b Rev. See Appendix K V01 NA Software Rev. Serial Number See Appendix K KWC223301QV C16036663000 NA 000276 Sample No. S01 S02 Equipment Details Cisco C9117AXI-x-K9 AIR-PWRINJ6 4.2 System Details System #

Manufacturer Cisco Systems MicroSemi for Cisco Description 1 Cisco C9117AXI-x-K9

+ PSU for conducted measurements 4.3 Mode of Operation Details Mode#

Description Samples S01, S02 Comments 1 Continuous Transmitting Continuous Transmitting, constant high duty cycle This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Page No: 11 of 69 Custom EMC Test Report No: EDCS 15634526 Appendix A: Conducted Emission Test Results Conducted Test Setup Diagram Target Maximum Channel Power The following table details the maximum supported Total Channel Power for all operating modes. OperatingMode LegacyCCK,1to11MB/s NonHT20,6to54Mbps NonHT20BeamForming,6to54Mbps HT/VHT20,M0toM31 HT/VHT20BeamForming,M0toM31 HT/VHT20STBC,M0toM7 MaximumChannelPower

(dBmEIRP) Frequency(MHz) 2412 28 25 29 25 29 25 2437 28 28 34 28 34 28 2462 28 24 29 25 29 25 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Page No: 12 of 69 Custom EMC Test Report No: EDCS 15634526 A.1 Duty Cycle Duty Cycle Test Requirement From KDB 558074, Section 6 6.0 Duty cycle, transmission duration and maximum power control level Preferably, all measurements of maximum conducted (average) output power will be performed with the EUT transmitting continuously (i.e., with a duty cycle of greater than or equal to 98%). When continuous operation cannot be realized, then the use of sweep triggering/signal gating techniques can be utilized to ensure that measurements are made only during transmissions at the maximum power control level. When continuous transmission cannot be achieved and sweep triggering/signal gating cannot be implemented, alternate procedures are provided that can be used to measure the average power; however, they will require an additional measurement of the transmitter duty cycle. Within this guidance document, the duty cycle refers to the fraction of time over which the transmitter is on and is transmitting at its maximum power control level. The duty cycle is considered to be constant if variations are less than 2 percent, otherwise the duty cycle is considered to be non-constant. The zero-span mode on a spectrum analyzer or EMI receiver if the response time and spacing between bins on the sweep are sufficient to permit accurate measurements of the on and off times of the transmitted signal. Set the center frequency of the instrument to the center frequency of the transmission. Set RBW OBW if possible; otherwise, set RBW to the largest available value. Set VBW RBW. Set detector = peak or average. The zero-span measurement method shall not be used unless both RBW and VBW are > 50/T and the number of sweep points across duration T exceeds 100. (For example, if VBW and/or RBW are limited to 3 MHz, then the zero-span method of measuring duty cycle shall not be used if T 16.7 microseconds.) Duty Cycle Test Method From KDB 558074, Section 6:

Duty Cycle Test Information Samples, Systems, and Modes System Number Description Samples System under test Support equipment 1 EUT Support S01 S02 Tested By :

Chris Blair Test Result : PASS Test Equipment See Appendix C for list of test equipment Date of testing:

09-Nov-18 - 13-Nov-18 Page No: 13 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 Duty Cycle Data Table Duty Cycle table and screen captures are shown below for power/psd modes. DataRate 6Mbps 11Mbps M0 Ontime

(ms) 2.097 1.326 5.432 TotalTime

(ms) 2.217 1.515 5.712 DutyCycle

(%) 94.6 87.5 95.1 Correction Factor

(dB) 0.24 0.58 0.22 Mode NonHT20 CCK HT20 Duty Cycle Data Screenshots Duty Cycle, 2412 MHz, 6Mbps This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Page No: 14 of 69 Custom EMC Test Report No: EDCS 15634526 Duty Cycle, 2412 MHz, 11Mbps Duty Cycle, 2412 MHz, M0 Page No: 15 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Page No: 16 of 69 Custom EMC Test Report No: EDCS 15634526 A.2 DTS Bandwidth (6dB Bandwidth) DTS Bandwidth Test Requirement For the FCC/ LP0002 (2018-01-10) (3.10.1.6) (2) (A) 15.247 (2) Systems using digital modulation techniques may operate in the 902928 MHz, 24002483.5 MHz, and 57255850 MHz bands. The minimum 6 dB bandwidth shall be at least 500 kHz. For Industry Canada:

RSS-247 5.2 (a) 5.2 Digital transmission systems DTSs include systems that employ digital modulation techniques resulting in spectral characteristics similar to direct sequence systems. The following applies to the bands 902-928 MHz and 2400-2483.5 MHz:

a) The minimum 6 dB bandwidth shall be 500 kHz. DTS Bandwidth/ 6dB Bandwidth Test Procedure Ref. KDB 558074 D01 DTS Meas Guidance v05, Section 8.2 ANSI C63.10: 2013, Clause 11.8.2 Option 2 6 BW Test Procedure 1. Set the radio in the continuous transmitting mode. 2. Allow the trace to stabilize. 3. Setting the x-dB bandwidth mode to -6dB within the measurement set up function. 4. Select the automatic OBW measurement function of an instrument to perform bandwidth measurement. 5. Capture graphs and record pertinent measurement data. Ref. KDB 558074 D01 DTS Meas Guidance v05, Section 8.2 ANSI C63.10: 2013, Clause 11.8.2 Option 2 6 BW Test parameters Page No: 17 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 Samples, Systems, and Modes System Number Description Samples 1 EUT Support S01 S02 Tested By :

Chris Blair Test Result : PASS Test Equipment See Appendix C for list of test equipment System under test Support equipment Date of testing:

20-Nov-18 Page No: 18 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 Mode Frequency

(MHz) 2412 2437 2462 CCK, 1 to 11 MB/s Non HT20, 6 to 54 Mbps HT/VHT20, M0 to M31 CCK, 1 to 11 MB/s Non HT20, 6 to 54 Mbps HT/VHT20, M0 to M31 CCK, 1 to 11 MB/s Non HT20, 6 to 54 Mbps HT/VHT20, M0 to M31 Data Rate

(Mbps) 11 6 m0 11 6 m0 11 6 m0 6dB BW

(MHz) 7.6 16.1 16.5 8.0 16.4 17.6 7.0 16.4 17.4 Limit

(kHz)

>500

>500

>500

>500

>500

>500

>500

>500

>500 Margin

(MHz) 7.1 15.6 16.0 7.5 15.9 17.1 6.5 15.9 16.9 Page No: 19 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 6dB Bandwidth, 2462 MHz, CCK, 1 to 11 MB/s This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Page No: 20 of 69 Custom EMC Test Report No: EDCS 15634526 A.3 Occupied Bandwidth Occupied Bandwidth Test Requirement The 99% occupied bandwidth is the frequency bandwidth such that, below its lower and above its upper frequency limits, the mean powers are each equal to 0.5% of the total mean power of the given emission. There is no limit for 99%

OBW. The 26 dB emission is the width of the emission that is constrained by the frequencies associated with the two outermost amplitude points (upper and lower frequencies) that are attenuated by 26 dB relative to the maximum level measured in the fundamental emission. Occupied Bandwidth Test Method Ref. ANSI C63.10: 2013 Occupied Bandwidth Test Procedure 1. Set the radio in the continuous transmitting mode. 2. Allow the trace to stabilize. 3. Setting the x-dB bandwidth mode to -26dB & OBW to 99% within the measurement set up function. 4. Select the automatic OBW measurement function of an instrument to perform bandwidth measurement. 5. Capture graphs and record pertinent measurement data. Ref. ANSI C63.10: 2013 section 6.9.3 Occupied Bandwidth Test parameters Page No: 21 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 Samples, Systems, and Modes System Number Description Samples 1 EUT Support S01 S02 Tested By :

Chris Blair Test Result : PASS Test Equipment See Appendix C for list of test equipment System under test Support equipment Date of testing:

09-Nov-18 - 13-Nov-18 Page No: 22 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 Mode Frequency

(MHz) 2412 2437 2462 CCK, 1 to 11 MB/s Non HT20, 6 to 54 Mbps HT/VHT20, M0 to M31 CCK, 1 to 11 MB/s Non HT20, 6 to 54 Mbps HT/VHT20, M0 to M31 CCK, 1 to 11 MB/s Non HT20, 6 to 54 Mbps HT/VHT20, M0 to M31 Data Rate

(Mbps) 11 6 m0 11 6 m0 11 6 m0 26dB BW

(MHz) 16.7 20.4 20.0 99% BW

(MHz) 12.681 16.539 17.536 16.6 22.1 20.5 16.7 20.5 20.1 12.801 16.629 17.578 12.776 16.573 17.545 Page No: 23 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 26dB / 99% Bandwidth, 2412 MHz, CCK, 1 to 11 MB/s This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Page No: 24 of 69 Custom EMC Test Report No: EDCS 15634526 A.4 Maximum Conducted Output Power Maximum Conducted Output Power Test Requirement FCC, 15.247/ LP0002 (2018-01-10) (3.10.1.2) (1) (C):

(b) The maximum peak conducted output power of the intentional radiator shall not exceed the following: (3) For systems using digital modulation in the 902-928 MHz, 2400-2483.5 MHz, and 5725-5850 MHz bands: 1 Watt. As an alternative to a peak power measurement, compliance with the one Watt limit can be based on a measurement of the maximum conducted output power. Maximum Conducted Output Power is defined as the total transmit power delivered to all antennas and antenna elements averaged across all symbols in the signaling alphabet when the transmitter is operating at its maximum power control level. Power must be summed across all antennas and antenna elements. The average must not include any time intervals during which the transmitter is off or is transmitting at a reduced power level. If multiple modes of operation are possible (e.g., alternative modulation methods), the maximum conducted output power is the highest total transmit power occurring in any mode.

(4) The conducted output power limit specified in paragraph (b) of this section is based on the use of antennas with directional gains that do not exceed 6 dBi. Except as shown in paragraph (c) of this section, if transmitting antennas of directional gain greater than 6 dBi are used, the conducted output power from the intentional radiator shall be reduced below the stated values in paragraphs (b)(1), (b)(2), and (b)(3) of this section, as appropriate, by the amount in dB that the directional gain of the antenna exceeds 6 dBi. Industry Canada, RSS-247:

5.4 Transmitter output power and equivalent isotropically radiated power (e.i.r.p.) requirements d) For DTSs employing digital modulation techniques operating in the bands 902-928 MHz and 2400-2483.5 MHz, the maximum peak conducted output power shall not exceed 1W. The e.i.r.p. shall not exceed 4 W, except as provided in section 5.4(e). As an alternative to a peak power measurement, compliance can be based on a measurement of the maximum conducted output power. The maximum conducted output power is the total transmit power delivered to all antennas and antenna elements, averaged across all symbols in the signalling alphabet when the transmitter is operating at its maximum power control level. Power must be summed across all antennas and antenna elements. The average must not include any time intervals during which the transmitter is off or transmitting at a reduced power level. If multiple modes of operation are implemented, the maximum conducted output power is the highest total transmit power occurring in any mode. The maximum supported antenna gain is 4dBi. The peak correlated gain for each mode is listed in the table below. Maximum Conducted Output Power Test Method Ref. KDB 558074 D01 DTS Meas Guidance v05 ANSI C63.10: 2013 Maximum Conducted Output power Test Procedure 1. Set the radio in the continuous transmitting mode at full power 2. Compute power by integrating the spectrum across the EBW (or alternatively entire 99% OBW) of the signal using the instruments band power measurement function. The integration shall be performed using the spectrum analyzer band-power measurement function with band limits set equal to the EBW or the OBW band edges. 3. Capture graphs and record pertinent measurement data. Ref. 558074 D01 DTS Meas Guidance v05, 8.3.2.2 Measurement using a spectrum analyzer (SA) ANSI C63.10: 2013, section 11.9.2.2.4 Method AVGSA-2 Maximum Conducted Output power Test parameters Page No: 25 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 The measure-and-sum technique is used for measuring in-band transmit power of a device. In the measure-and-sum approach, the conducted emission level is measured at each antenna port. The measured results at the various antenna ports are then summed mathematically to determine the total emission level from the device. Summing is performed in linear power units. (See ANSI C63.10 section 14.3 for Guidance) Samples, Systems, and Modes System Number System under test Support equipment Description Samples 1 EUT Support S01 S02 Tested By :

Chris Blair Test Result : PASS Test Equipment See Appendix C for list of test equipment Note: Limit is modified to ensure complying with both conducted power limit of 30dBm and eirp limit of 36 dBm Date of testing:

09-Nov-18 - 13-Nov-18 Page No: 26 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526

) z H M

(

y c n e u q e r F 2 1 4 2 Mode CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps HT/VHT20, M0 to M7 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M16 to M23 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M16 to M23 HT/VHT20, M24 to M31 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M16 to M23 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M16 to M23 HT/VHT20 Beam Forming, M24 to M31 HT/VHT20 STBC, M0 to M7 HT/VHT20 STBC, M0 to M7 HT/VHT20 STBC, M0 to M7 a n n e t n A d e t a e r r o C l

) i B d

(

i n a G 4 4 4 4 4 4 4 4 7 9 10 4 4 4 4 4 4 4 4 4 4 7 4 9 6 4 10 7 5 4 4 4 4

) m B d

(

r e w o P x a M 1

) m B d

(

r e w o P x a M 2 x T 19.0 19.0 19.0 19.0 17.4 16.6 16.6 14.6 15.7 14.6 13.6 18.5 18.5 18.5 17.2 17.2 17.2 16.5 16.5 16.5 16.5 17.2 18.5 16.5 17.2 17.2 14.4 15.4 15.4 16.5 18.5 17.2 16.5 x T 18.3 18.3 18.3 15.6 15.6 13.7 14.6 13.7 12.7 17.4 17.4 16.5 16.5 16.5 15.5 15.5 15.5 15.5 16.5 17.4 15.5 16.5 16.5 13.4 14.3 14.3 15.5 17.4 16.5 15.5 s h t a P x T 1 2 3 4 1 2 3 4 2 3 4 1 2 2 3 3 3 4 4 4 4 2 2 3 3 3 4 4 4 4 2 3 4 Page No: 27 of 69

) m B d

(

r e w o P x a M 3

) m B d

(

r e w o P x a M 4 x T 17.6 17.6 14.9 13.1 13.1 11.8 15.8 15.8 15.8 14.7 14.7 14.7 14.7 14.7 15.8 15.8 12.6 13.7 13.7 14.7 15.8 14.7 x T 17.6 13.2 11.9 14.8 14.8 14.8 14.8 13.0 13.9 13.9 14.8 14.8 l e n n a h C x T l a t o T

) m B d

(

r e w o P 23.0 25.7 27.1 28.2 21.4 23.1 24.5 23.7 25.2 27.6 28.6 22.5 25.0 25.0 25.3 25.3 25.3 25.5 25.5 25.5 25.5 26.9 25.0 29.4 27.3 25.3 29.4 27.4 25.4 25.5 25.0 25.3 25.5 P R E I

) m B d

(

t i m L i 33.4 33.4 33.4 33.4 33.8 33.8 33.8 33.8 35.8 35.8 35.8 33.8 33.8 33.8 33.8 33.8 33.8 33.8 33.8 33.8 33.8 35.8 33.8 35.8 35.8 33.8 35.8 35.8 34.8 33.8 33.8 33.8 33.8

) B d

(

n g r a M i 10.4 7.7 6.3 5.2 12.4 10.6 9.2 10.0 10.6 8.1 7.2 11.3 8.8 8.8 8.5 8.5 8.5 8.3 8.3 8.3 8.3 8.9 8.8 6.4 8.5 8.5 6.3 8.4 9.4 8.3 8.8 8.5 8.3 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential 7 3 4 2 2 6 4 2 Custom EMC Test Report No: EDCS 15634526 CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps HT/VHT20, M0 to M7 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M16 to M23 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M16 to M23 HT/VHT20, M24 to M31 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M16 to M23 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M16 to M23 HT/VHT20 Beam Forming, M24 to M31 HT/VHT20 STBC, M0 to M7 HT/VHT20 STBC, M0 to M7 HT/VHT20 STBC, M0 to M7 CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps 1 2 3 4 1 2 3 4 2 3 4 1 2 2 3 3 3 4 4 4 4 2 2 3 3 3 4 4 4 4 2 3 4 1 2 3 4 1 2 3 4 4 4 4 4 4 4 4 4 7 9 10 4 4 4 4 4 4 4 4 4 4 7 4 9 6 4 10 7 5 4 4 4 4 4 4 4 4 4 4 4 4 19.3 19.3 19.3 19.3 19.2 19.2 19.2 19.2 19.2 19.2 19.2 19.0 19.0 19.0 19.0 19.0 19.0 19.0 19.0 19.0 19.0 19.0 19.0 19.0 19.0 19.0 19.0 19.0 19.0 19.0 19.0 19.0 19.0 19.2 19.2 19.2 19.2 17.5 16.3 16.3 15.3 18.1 18.1 18.1 18.3 18.3 18.3 18.3 18.3 18.3 18.2 18.2 18.2 18.2 18.2 18.2 18.2 18.2 18.2 18.2 18.2 18.2 18.2 18.2 18.2 18.2 18.2 18.2 18.2 18.2 18.2 18.1 18.1 18.1 15.6 15.6 14.5 17.3 17.3 17.6 17.6 17.6 17.6 17.4 17.4 17.4 17.4 17.4 17.4 17.4 17.4 17.4 17.4 17.4 17.4 17.4 17.4 17.4 17.4 17.2 17.2 14.6 13.8 17.7 17.7 17.7 17.4 17.4 17.4 17.4 17.4 17.4 17.4 17.4 17.4 17.5 13.8 23.3 25.8 27.1 28.2 23.2 25.8 27.2 28.3 28.8 32.2 34.3 23.0 25.6 25.6 27.0 27.0 27.0 28.1 28.1 28.1 28.1 28.6 25.6 32.0 29.0 27.0 34.1 31.1 29.1 28.1 25.6 27.0 28.1 23.2 25.7 27.0 28.1 21.5 23.0 24.3 24.4 33.4 33.4 33.4 33.4 33.8 33.8 33.8 33.8 35.8 35.8 35.8 33.8 33.8 33.8 33.8 33.8 33.8 33.8 33.8 33.8 33.8 35.8 33.8 35.8 35.8 33.8 35.8 35.8 34.8 33.8 33.8 33.8 33.8 33.4 33.4 33.4 33.4 33.8 33.8 33.8 33.8 10.1 7.7 6.3 5.2 10.6 8.0 6.6 5.5 7.0 3.6 1.5 10.8 8.1 8.1 6.7 6.7 6.7 5.7 5.7 5.7 5.7 7.1 8.1 3.7 6.7 6.7 1.7 4.7 5.7 5.7 8.1 6.7 5.7 10.2 7.7 6.4 5.3 12.3 10.8 9.4 9.3 Page No: 28 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 Non HT20 Beam Forming, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps HT/VHT20, M0 to M7 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M16 to M23 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M16 to M23 HT/VHT20, M24 to M31 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M16 to M23 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M16 to M23 HT/VHT20 Beam Forming, M24 to M31 HT/VHT20 STBC, M0 to M7 HT/VHT20 STBC, M0 to M7 HT/VHT20 STBC, M0 to M7 2 3 4 1 2 2 3 3 3 4 4 4 4 2 2 3 3 3 4 4 4 4 2 3 4 7 9 10 4 4 4 4 4 4 4 4 4 4 7 4 9 6 4 10 7 5 4 4 4 4 16.3 14.4 14.4 18.2 17.3 17.3 17.3 17.3 17.3 16.2 16.2 16.2 16.2 17.3 17.3 15.3 17.3 17.3 14.2 15.3 16.2 16.2 17.3 17.3 16.2 15.6 13.4 13.4 16.2 16.2 16.2 16.2 16.2 15.3 15.3 15.3 15.3 16.2 16.2 14.4 16.2 16.2 13.4 14.4 15.3 15.3 16.2 16.2 15.3 12.7 12.7 12.8 15.5 15.5 15.5 14.4 14.4 14.4 14.4 13.5 15.5 15.5 12.6 13.5 14.4 14.4 15.5 14.4 14.6 14.6 14.6 14.6 12.5 13.7 14.6 14.6 14.6 26.0 27.3 29.4 22.2 23.8 23.8 25.2 25.2 25.2 25.2 25.2 25.2 25.2 26.8 23.8 28.2 27.2 25.2 29.3 27.3 26.2 25.2 23.8 25.2 25.2 35.8 35.8 35.8 33.8 33.8 33.8 33.8 33.8 33.8 33.8 33.8 33.8 33.8 35.8 33.8 35.8 35.8 33.8 35.8 35.8 34.8 33.8 33.8 33.8 33.8 9.8 8.4 6.4 11.6 10.0 10.0 8.6 8.6 8.6 8.6 8.6 8.6 8.6 9.0 10.0 7.5 8.6 8.6 6.5 8.5 8.6 8.6 10.0 8.6 8.6 Page No: 29 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 Maximum Transmit Output Power, 2437 MHz, Non HT20 Beam Forming, 6 to 54 Mbps Antenna A Antenna C Antenna B Antenna D Page No: 30 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 A.5 Power Spectral Density Power Spectral Density Test Requirement 15.247 (e) / RSS-247 5.2 (b) / LP0002 (2018-01-10) (3.10.1.6) (2) (B):

5.2 Digital transmission systems DTSs include systems that employ digital modulation techniques resulting in spectral characteristics similar to direct sequence systems. The following applies to the bands 902-928 MHz and 2400-2483.5 MHz:

b) The transmitter power spectral density conducted from the transmitter to the antenna shall not be greater than 8 dBm in any 3 kHz band during any time interval of continuous transmission. This power spectral density shall be determined in accordance with the provisions of section 5.4(d), (i.e. the power spectral density shall be determined using the same method as is used to determine the conducted output power). Power Spectral Density Test Method Ref. KDB 558074 D01 DTS Meas Guidance v05 ANSI C63.10: 2013 Power Spectral Density Test Procedure 1. Set the radio in the continuous transmitting mode at full power 2.Configure Spectrum analyzer as per test parameters below and Peak search marker 3. Capture graphs and record pertinent measurement data. Ref. KDB 558074 D01 DTS Meas Guidance v05, section 8.4 DTS maximum power spectral density level in the fundamental emission ANSI C63.10: 2013, section 11.10.5 Average PSD Power Spectral Density Test parameters Page No: 31 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 The Measure and add 10 log(N) dB technique, where N is the number of outputs, is used for measuring in-band Power Spectral Density. (See ANSI C63.10 section 14.3.2.3 ) Samples, Systems, and Modes System Number System under test Support equipment Description Samples 1 EUT Support S01 S02 Tested By :

Chris Blair Test Result : PASS Test Equipment See Appendix C for list of test equipment Date of testing:

09-Nov-18 - 13-Nov-18 Page No: 32 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 Frequency

(MHz) 2412 2437 2462 Mode CCK, 1 to 11 MB/s Non HT20, 6 to 54 Mbps HT/VHT20, M0 to M31 CCK, 1 to 11 MB/s Non HT20, 6 to 54 Mbps HT/VHT20, M0 to M31 CCK, 1 to 11 MB/s Non HT20, 6 to 54 Mbps HT/VHT20, M0 to M31 Data Rate

(Mbps) PSD /

Antenna

(dBm/3kHz) Total PSD

(dBm/3kHz) Limit

(dBm/3kHz) 11 6 m0 11 6 m0 11 6 m0

-2.9

-9.6

-7.7

-3.6

-8.0

-6.0

-3.2

-9.3

-7.3 3.1

-3.6

-1.7 2.4

-2.0 0.0 2.8

-3.3

-1.3 7.4 7.8 7.8 7.4 7.8 7.8 7.4 7.8 7.8 Margin

(dB) 4.3 11.3 9.4 5.0 9.7 7.7 4.6 11.0 9.0 Page No: 33 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 Power Spectral Density, 2412 MHz, CCK, 1 to 11 MB/s This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Page No: 34 of 69 Custom EMC Test Report No: EDCS 15634526 A.6 Conducted Spurious Emissions Conducted Spurious Emissions Test Requirement 15.205 / RSS-Gen / LP0002 (2018-01-10) (3.10.1.5) (2.8):

Radiated emissions which fall in the restricted bands, as defined in Section 15.205(a) and RSS-GEN section 8.10, must also comply with the radiated emission limits specified in Section 15.209(a) (see Section 15.205(c)) and RSS-Gen section 8.9 RSS-Gen 8.9 Except when the requirements applicable to a given device state otherwise, emissions from licence-exempt transmitters shall comply with the field strength limits shown in Table 4 and Table 5 below. Additionally, the level of any transmitter emission shall not exceed the level of the transmitters fundamental emission. RSS-Gen 8.10 (b) Unwanted emissions that fall into restricted bands of Table 6 shall comply with the limits specified in RSS-Gen; and (c ) Unwanted emissions that do not fall within the restricted frequency bands of Table 6 shall comply either with the limits specified in the applicable RSS or with those specified in this RSS-Gen. Use formula below to substitute conducted measurements in place of radiated measurements E[dBV/m] = EIRP[dBm] - 20 log(d[meters]) + 104.77, where E = field strength and d = 3 meter 1) Average Plot, Limit= -41.25 dBm eirp 2) Peak plot, Limit = -21.25 dBm eirp Conducted Spurious Emissions Test Method Ref. KDB 558074 D01 DTS Meas Guidance v05 ANSI C63.10: 2013 Conducted Spurious Emissions Test Procedure 1. Connect the antenna port(s) to the spectrum analyzer input. 2. Place the radio in continuous transmit mode 3. Configure Spectrum analyzer as per test parameters below (be sure to enter all losses between the transmitter output and the spectrum analyzer). 4. Use the peak marker function to determine the maximum spurs amplitude level. 5. The measure-and-sum technique is used for measuring in-band transmit power of a device. In the measure-and-sum approach, the conducted emission level is measured at each antenna port. The measured results at the various antenna ports are then summed mathematically to determine the total emission level from the device. Summing is performed in linear power units. The worst case output is recorded. (see ANSI C63.10 2013 section 14.3.2.2) 6. Capture graphs and record pertinent measurement data. Ref. KDB 558074 D01 DTS Meas Guidance v05, section 8.1 c) 3, section 8.6 DTS emissions in restricted frequency bands ANSI C63.10: 2013 section 11.12.2.4 (Peak) & 11.12.2.5.2 (Average) Conducted Spurious Emissions Test parameters Peak Span = 30MHz to 26.5GHz / 26.5GHz to 40GHz RBW = 1 MHz Average Span = 30MHz to 26.5GHz / 26.5GHz to 40GHz RBW = 1 MHz Page No: 35 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 VBW 3 MHz Sweep = Auto Detector = Peak Trace = Max Hold. ANSI C63.10: 2013 section 11.12.2.2 c) add the max antenna gain + ground reflection factor (4.7 dB for frequencies between 30 MHz and 1000 MHz, and 0 dB for frequencies > 1000 MHz). Samples, Systems, and Modes System Number VBW 3 MHz Sweep = Auto Detector = RMS Power Averaging System under test Support equipment Description Samples 1 EUT Support S01 S02 Tested By :

Chris Blair Test Result : PASS Test Equipment See Appendix C for list of test equipment Date of testing:

09-Nov-18 - 13-Nov-18 Page No: 36 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 Conducted Spurs Average Upper, All Antennas Conducted Spurs Peak Upper, All Antennas Page No: 37 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526

) z H M

(

y c n e u q e r F 2 1 4 2 Mode CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps HT/VHT20, M0 to M7 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M16 to M23 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M16 to M23 HT/VHT20, M24 to M31 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M16 to M23 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M16 to M23 HT/VHT20 Beam Forming, M24 to M31 HT/VHT20 STBC, M0 to M7 HT/VHT20 STBC, M0 to M7 HT/VHT20 STBC, M0 to M7 a n n e t n A d e t a e r r o C l

) i B d

(

i n a G 4 4 4 4 4 4 4 4 7 9 10 4 4 4 4 4 4 4 4 4 4 7 4 9 6 4 10 7 5 4 4 4 4 s h t a P x T 1 2 3 4 1 2 3 4 2 3 4 1 2 2 3 3 3 4 4 4 4 2 2 3 3 3 4 4 4 4 2 3 4 r e w o P r u p S 1 x T

) m B d

(

-83.3

-83.3

-83.3

-83.3

-84.7

-84.5

-84.5

-84.5

-84.7

-84.5

-84.7

-83.8

-83.8

-83.8

-84.5

-84.5

-84.5

-84.7

-84.7

-84.7

-84.7

-84.5

-83.8

-84.7

-84.5

-84.5

-84.2

-84.5

-84.5

-84.7

-83.8

-84.5

-84.7 r e w o P r u p S 2 x T

) m B d

(

-81.4

-81.4

-81.4

-84.9

-84.9

-84.9

-84.9

-84.9

-85.0

-82.1

-82.1

-83.7

-83.7

-83.7

-85.1

-85.1

-85.1

-85.1

-83.7

-82.1

-85.1

-83.7

-83.7

-84.7

-85.0

-85.0

-85.1

-82.1

-83.7

-85.1 r e w o P r u p S 3 x T

) m B d

(

-78.3

-78.3

-81.8

-85.0

-85.0

-85.1

-80.1

-80.1

-80.1

-82.2

-82.2

-82.2

-82.2

-82.2

-80.1

-80.1

-84.9

-84.5

-84.5

-82.2

-80.1

-82.2 r e w o P r u p S 4 x T

) m B d

(

-85.2

-84.6

-85.0

-84.6

-84.6

-84.6

-84.6

-84.8

-84.5

-84.5

-84.6

-84.6 r u p S d e t c u d n o C l a t o T

) m B d

(

-79.3

-75.2

-71.7

-71.3

-80.7

-77.7

-74.7

-74.7

-74.8

-71.0

-68.9

-79.8

-75.9

-75.9

-73.5

-73.5

-73.5

-74.0

-74.0

-74.0

-74.0

-74.1

-75.9

-70.0

-71.5

-73.5

-68.6

-71.6

-73.6

-74.0

-75.9

-73.5

-74.0 Page No: 38 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential

) m B d

(

t i m L i

-41.83

-41.83

-41.83

-41.83

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

) B d

(

n g r a M I 37.5 33.4 29.9 29.4 39.2 36.2 33.2 33.2 33.3 29.5 27.4 38.3 34.4 34.4 32.1 32.1 32.1 32.5 32.5 32.5 32.5 32.6 34.4 28.5 30.1 32.1 27.1 30.1 32.1 32.5 34.4 32.1 32.5 7 3 4 2 2 6 4 2 Custom EMC Test Report No: EDCS 15634526 CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps HT/VHT20, M0 to M7 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M16 to M23 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M16 to M23 HT/VHT20, M24 to M31 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M16 to M23 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M16 to M23 HT/VHT20 Beam Forming, M24 to M31 HT/VHT20 STBC, M0 to M7 HT/VHT20 STBC, M0 to M7 HT/VHT20 STBC, M0 to M7 CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps 1 2 3 4 1 2 3 4 2 3 4 1 2 2 3 3 3 4 4 4 4 2 2 3 3 3 4 4 4 4 2 3 4 1 2 3 4 1 2 3 4 4 4 4 4 4 4 4 4 7 9 10 4 4 4 4 4 4 4 4 4 4 7 4 9 6 4 10 7 5 4 4 4 4 4 4 4 4 4 4 4 4

-85.0

-85.0

-85.0

-85.0

-84.9

-84.9

-84.9

-84.9

-84.9

-84.9

-84.9

-84.6

-84.6

-84.6

-84.6

-84.6

-84.6

-84.6

-84.6

-84.6

-84.6

-84.6

-84.6

-84.6

-84.6

-84.6

-84.6

-84.6

-84.6

-84.6

-84.6

-84.6

-84.6

-84.7

-84.7

-84.7

-84.7

-84.7

-84.5

-84.5

-84.4

-85.0

-85.0

-85.0

-85.0

-85.0

-85.0

-85.0

-85.0

-85.0

-85.1

-85.1

-85.1

-85.1

-85.1

-85.1

-85.1

-85.1

-85.1

-85.1

-85.1

-85.1

-85.1

-85.1

-85.1

-85.1

-85.1

-85.1

-85.1

-85.1

-85.1

-85.1

-85.1

-85.1

-84.9

-84.9

-85.0

-79.6

-79.6

-80.0

-80.0

-80.0

-80.0

-80.5

-80.5

-80.5

-80.5

-80.5

-80.5

-80.5

-80.5

-80.5

-80.5

-80.5

-80.5

-80.5

-80.5

-80.5

-80.5

-80.4

-80.4

-85.1

-85.3

-85.0

-85.1

-85.1

-85.0

-85.0

-85.0

-85.0

-85.0

-85.0

-85.0

-85.0

-85.0

-85.0

-85.0

-81.0

-78.0

-73.6

-72.9

-80.9

-77.9

-73.9

-73.1

-74.9

-68.9

-67.1

-80.6

-77.8

-77.8

-74.1

-74.1

-74.1

-73.3

-73.3

-73.3

-73.3

-74.8

-77.8

-69.1

-72.1

-74.1

-67.3

-70.3

-72.3

-73.3

-77.8

-74.1

-73.3

-80.7

-77.9

-74.1

-73.3

-80.7

-77.7

-76.1

-74.9

-41.83

-41.83

-41.83

-41.83

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.83

-41.83

-41.83

-41.83

-41.49

-41.49

-41.49

-41.49 39.2 36.2 31.8 31.1 39.4 36.4 32.4 31.6 33.4 27.4 25.6 39.1 36.3 36.3 32.6 32.6 32.6 31.8 31.8 31.8 31.8 33.3 36.3 27.6 30.6 32.6 25.8 28.8 30.8 31.8 36.3 32.6 31.8 38.9 36.1 32.2 31.4 39.2 36.2 34.6 33.4 Page No: 39 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 Non HT20 Beam Forming, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps HT/VHT20, M0 to M7 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M16 to M23 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M16 to M23 HT/VHT20, M24 to M31 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M16 to M23 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M16 to M23 HT/VHT20 Beam Forming, M24 to M31 HT/VHT20 STBC, M0 to M7 HT/VHT20 STBC, M0 to M7 HT/VHT20 STBC, M0 to M7 2 3 4 1 2 2 3 3 3 4 4 4 4 2 2 3 3 3 4 4 4 4 2 3 4 7 9 10 4 4 4 4 4 4 4 4 4 4 7 4 9 6 4 10 7 5 4 4 4 4

-84.5

-84.5

-84.5

-84.5

-84.7

-84.7

-84.7

-84.7

-84.7

-84.6

-84.6

-84.6

-84.6

-84.7

-84.7

-84.7

-84.7

-84.7

-84.4

-84.7

-84.6

-84.6

-84.7

-84.7

-84.6

-84.9

-84.8

-84.8

-85.0

-85.0

-85.0

-85.0

-85.0

-85.0

-85.0

-85.0

-85.0

-85.0

-85.0

-84.9

-85.0

-85.0

-85.1

-84.9

-85.0

-85.0

-85.0

-85.0

-85.0

-85.0

-85.0

-84.7

-85.4

-85.4

-85.4

-85.1

-85.1

-85.1

-85.1

-85.2

-85.4

-85.4

-85.0

-85.2

-85.1

-85.1

-85.4

-85.1

-84.7

-84.7

-84.7

-84.7

-85.1

-84.7

-84.7

-84.7

-84.7

-74.7

-71.0

-68.7

-80.5

-77.8

-77.8

-76.3

-76.3

-76.3

-74.8

-74.8

-74.8

-74.8

-74.8

-77.8

-71.2

-74.3

-76.3

-68.9

-71.8

-73.8

-74.8

-77.8

-76.3

-74.8

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49 33.2 29.5 27.2 39.0 36.3 36.3 34.8 34.8 34.8 33.3 33.3 33.3 33.3 33.3 36.3 29.7 32.8 34.8 27.4 30.4 32.3 33.3 36.3 34.8 33.3 Page No: 40 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 Conducted Spurs Average, 2437 MHz, Non HT20 Beam Forming, 6 to 54 Mbps Antenna A Antenna C Antenna B Antenna D Page No: 41 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526

) z H M

(

y c n e u q e r F 2 1 4 2 Mode CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps HT/VHT20, M0 to M7 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M16 to M23 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M16 to M23 HT/VHT20, M24 to M31 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M16 to M23 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M16 to M23 HT/VHT20 Beam Forming, M24 to M31 HT/VHT20 STBC, M0 to M7 HT/VHT20 STBC, M0 to M7 HT/VHT20 STBC, M0 to M7 a n n e t n A d e t a e r r o C l

) i B d

(

i n a G 4 4 4 4 4 4 4 4 7 9 10 4 4 4 4 4 4 4 4 4 4 7 4 9 6 4 10 7 5 4 4 4 4 s h t a P x T 1 2 3 4 1 2 3 4 2 3 4 1 2 2 3 3 3 4 4 4 4 2 2 3 3 3 4 4 4 4 2 3 4 r e w o P r u p S 1 x T

) m B d

(

-67.0

-67.0

-67.0

-67.0

-67.7

-67.4

-67.4

-67.7

-67.8

-67.7

-67.5

-66.9

-66.9

-66.9

-67.5

-67.5

-67.5

-67.7

-67.7

-67.7

-67.7

-67.5

-66.9

-67.7

-67.5

-67.5

-68.0

-66.5

-66.5

-67.7

-66.9

-67.5

-67.7 r e w o P r u p S 2 x T

) m B d

(

-67.1

-67.1

-67.1

-67.5

-67.5

-67.2

-68.5

-67.2

-67.6

-67.7

-67.7

-67.8

-67.8

-67.8

-66.6

-66.6

-66.6

-66.6

-67.8

-67.7

-66.6

-67.8

-67.8

-67.4

-67.4

-67.4

-66.6

-67.7

-67.8

-66.6 r e w o P r u p S 3 x T

) m B d

(

-63.7

-63.7

-66.1

-68.1

-68.1

-67.5

-68.1

-68.1

-68.1

-67.7

-67.7

-67.7

-67.7

-67.7

-68.1

-68.1

-67.7

-67.6

-67.6

-67.7

-68.1

-67.7 r e w o P r u p S 4 x T

) m B d

(

-67.5

-67.9

-68.0

-67.9

-67.9

-67.9

-67.9

-66.9

-67.2

-67.2

-67.9

-67.9 r u p S d e t c u d n o C l a t o T

) m B d

(

-63.0

-60.0

-56.9

-56.0

-63.7

-60.4

-58.2

-57.7

-58.1

-53.9

-51.6

-62.9

-60.3

-60.3

-59.0

-59.0

-59.0

-57.4

-57.4

-57.4

-57.4

-57.6

-60.3

-53.5

-57.0

-59.0

-51.5

-54.1

-56.1

-57.4

-60.3

-59.0

-57.4 Page No: 42 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential

) m B d

(

t i m L i

-21.83

-21.83

-21.83

-21.83

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

) B d

(

n g r a M I 41.2 38.2 35.0 34.2 42.2 38.9 36.7 36.2 36.6 32.4 30.1 41.4 38.8 38.8 37.5 37.5 37.5 35.9 35.9 35.9 35.9 36.1 38.8 32.0 35.5 37.5 30.0 32.6 34.6 35.9 38.8 37.5 35.9 7 3 4 2 2 6 4 2 Custom EMC Test Report No: EDCS 15634526 CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps HT/VHT20, M0 to M7 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M16 to M23 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M16 to M23 HT/VHT20, M24 to M31 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M16 to M23 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M16 to M23 HT/VHT20 Beam Forming, M24 to M31 HT/VHT20 STBC, M0 to M7 HT/VHT20 STBC, M0 to M7 HT/VHT20 STBC, M0 to M7 CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps 1 2 3 4 1 2 3 4 2 3 4 1 2 2 3 3 3 4 4 4 4 2 2 3 3 3 4 4 4 4 2 3 4 1 2 3 4 1 2 3 4 4 4 4 4 4 4 4 4 7 9 10 4 4 4 4 4 4 4 4 4 4 7 4 9 6 4 10 7 5 4 4 4 4 4 4 4 4 4 4 4 4

-67.2

-67.2

-67.2

-67.2

-68.1

-68.1

-68.1

-68.1

-68.1

-68.1

-68.1

-68.0

-68.0

-68.0

-68.0

-68.0

-68.0

-68.0

-68.0

-68.0

-68.0

-68.0

-68.0

-68.0

-68.0

-68.0

-68.0

-68.0

-68.0

-68.0

-68.0

-68.0

-68.0

-67.5

-67.5

-67.5

-67.5

-66.4

-66.6

-66.6

-67.7

-67.9

-67.9

-67.9

-67.7

-67.7

-67.7

-67.7

-67.7

-67.7

-67.9

-67.9

-67.9

-67.9

-67.9

-67.9

-67.9

-67.9

-67.9

-67.9

-67.9

-67.9

-67.9

-67.9

-67.9

-67.9

-67.9

-67.9

-67.9

-67.9

-67.9

-68.2

-68.2

-68.2

-68.3

-68.3

-67.1

-66.0

-66.0

-67.3

-67.3

-67.3

-67.3

-67.4

-67.4

-67.4

-67.4

-67.4

-67.4

-67.4

-67.4

-67.4

-67.4

-67.4

-67.4

-67.4

-67.4

-67.4

-67.4

-66.5

-66.5

-67.8

-68.1

-67.6

-67.9

-67.9

-67.7

-67.7

-67.7

-67.7

-67.7

-67.7

-67.7

-67.7

-67.7

-68.3

-67.6

-63.2

-60.5

-58.2

-57.1

-64.1

-60.9

-58.9

-57.7

-57.9

-53.9

-51.7

-64.0

-60.9

-60.9

-59.0

-59.0

-59.0

-57.7

-57.7

-57.7

-57.7

-57.9

-60.9

-54.0

-57.0

-59.0

-51.7

-54.7

-56.7

-57.7

-60.9

-59.0

-57.7

-63.5

-60.8

-58.6

-57.5

-62.4

-60.4

-58.7

-57.6

-21.83

-21.83

-21.83

-21.83

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.83

-21.83

-21.83

-21.83

-21.49

-21.49

-21.49

-21.49 41.4 38.7 36.4 35.3 42.6 39.4 37.4 36.2 36.4 32.4 30.2 42.5 39.4 39.4 37.5 37.5 37.5 36.2 36.2 36.2 36.2 36.4 39.4 32.5 35.5 37.5 30.2 33.2 35.2 36.2 39.4 37.5 36.2 41.7 39.0 36.7 35.7 40.9 38.9 37.2 36.1 Page No: 43 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 Non HT20 Beam Forming, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps HT/VHT20, M0 to M7 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M16 to M23 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M16 to M23 HT/VHT20, M24 to M31 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M16 to M23 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M16 to M23 HT/VHT20 Beam Forming, M24 to M31 HT/VHT20 STBC, M0 to M7 HT/VHT20 STBC, M0 to M7 HT/VHT20 STBC, M0 to M7 2 3 4 1 2 2 3 3 3 4 4 4 4 2 2 3 3 3 4 4 4 4 2 3 4 7 9 10 4 4 4 4 4 4 4 4 4 4 7 4 9 6 4 10 7 5 4 4 4 4

-66.6

-66.9

-66.9

-68.2

-67.6

-67.6

-67.6

-67.6

-67.6

-66.5

-66.5

-66.5

-66.5

-67.6

-67.6

-67.6

-67.6

-67.6

-67.7

-67.6

-66.5

-66.5

-67.6

-67.6

-66.5

-68.3

-68.5

-68.5

-66.3

-66.3

-66.3

-66.3

-66.3

-68.0

-68.0

-68.0

-68.0

-66.3

-66.3

-67.5

-66.3

-66.3

-67.5

-67.5

-68.0

-68.0

-66.3

-66.3

-68.0

-67.1

-67.1

-68.1

-67.9

-67.9

-67.9

-67.5

-67.5

-67.5

-67.5

-67.4

-67.9

-67.9

-67.2

-67.4

-67.5

-67.5

-67.9

-67.5

-67.9

-67.9

-67.9

-67.9

-67.5

-67.5

-67.9

-67.9

-67.9

-57.4

-53.7

-51.6

-64.2

-59.9

-59.9

-58.4

-58.4

-58.4

-57.4

-57.4

-57.4

-57.4

-56.9

-59.9

-53.7

-56.4

-58.4

-51.5

-54.5

-56.4

-57.4

-59.9

-58.4

-57.4

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49 35.9 32.2 30.1 42.7 38.4 38.4 36.9 36.9 36.9 35.9 35.9 35.9 35.9 35.4 38.4 32.2 34.9 36.9 30.0 33.0 34.9 35.9 38.4 36.9 35.9 Page No: 44 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 Conducted Spurs Peak, 2412 MHz, HT/VHT20 Beam Forming, M0 to M7 Antenna A Antenna C Antenna B Antenna D Page No: 45 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 A.7 Conducted Bandedge (Restricted Band) Conducted Band Edge Test Requirement 15.247 / LP0002 (2018-01-10) (3.10.1.5) (2.8):

(d) In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 dB instead of 20 dB. Attenuation below the general limits specified in 15.209(a) is not required. In addition, radiated emissions which fall in the restricted bands, as defined in 15.205(a), must also comply with the radiated emission limits specified in 15.209(a) (see 15.205(c)). RSS-247 5.5 Unwanted emissions In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated device is operating, the RF power that is produced shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided that the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of root-mean-square averaging over a time interval, as permitted under section 5.4(d), the attenuation required shall be 30 dB instead of 20 dB. Attenuation below the general field strength limits specified in RSS-Gen is not required. 15.205 / RSS-Gen Radiated emissions which fall in the restricted bands, as defined in Section 15.205(a), and RSS-Gen 8.10 must also comply with the radiated emission limits specified in Section 15.209(a) (see Section 15.205(c)) and RSS-Gen 8.9. Conducted Bandedge Test Method Ref. KDB 558074 D01 DTS Meas Guidance v05 ANSI C63.10: 2013 Conducted Band edge Test Procedure 1. Connect the antenna port(s) to the spectrum analyzer input. 2. Place the radio in continuous transmit mode. Use the procedures in KDB 558074 D01 DTS Meas Guidance v04 to substitute conducted measurements in place of radiated measurements. 3. Configure Spectrum analyzer as per test parameters below (be sure to enter all losses between the transmitter output and the spectrum analyzer). 4. Place a marker at the end of the restricted band closest to the transmit frequency to show compliance. Also measure any emissions in the restricted bands. 5. The measure-and-sum technique is used for measuring in-band transmit power of a device. In the measure-and-sum approach, the conducted emission level is measured at each antenna port. The measured results at the various antenna ports are then summed mathematically to determine the total emission level from the device. Summing is performed in linear power units. The worst case output is recorded. 6. Place a marker at the end of the restricted band closest to the transmit frequency to show compliance. Also measure any emissions in the restricted bands 7. Capture graphs and record pertinent measurement data. Ref. KDB 558074 D01 DTS Meas Guidance v05, section 8.1 c) 3, section 8.6 DTS emissions in restricted frequency bands ANSI C63.10: 2013 section 11.12.2.4 (Peak) & 11.12.2.5.2 (Average) Page No: 46 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 Conducted Spurious Emissions Test parameters Peak RBW = 1 MHz VBW 3 MHz Sweep = Auto Detector = Peak Trace = Max Hold. Samples, Systems, and Modes System Number Description Samples 1 EUT Support S01 S02 Tested By :

Chris Blair Test Result : PASS Test Equipment See Appendix C for list of test equipment Average RBW = 1 MHz VBW 3 MHz Sweep = Auto Detector = RMS Power Averaging System under test Support equipment Date of testing:

09-Nov-18 - 13-Nov-18 Page No: 47 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 Restricted Band

) z H M

(

y c n e u q e r F 2 1 4 2 Mode CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps HT/VHT20, M0 to M7 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M16 to M23 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M16 to M23 HT/VHT20, M24 to M31 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M16 to M23 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M16 to M23 HT/VHT20 Beam Forming, M24 to M31 HT/VHT20 STBC, M0 to M7 HT/VHT20 STBC, M0 to M7 HT/VHT20 STBC, M0 to M7

) i B d

(

n i a G d e a t a n l n e e r r t o n C A 4 4 4 4 4 4 4 4 7 9 10 4 4 4 4 4 4 4 4 4 4 7 4 9 6 4 10 7 5 4 4 4 4 s h t a P x T 1 2 3 4 1 2 3 4 2 3 4 1 2 2 3 3 3 4 4 4 4 2 2 3 3 3 4 4 4 4 2 3 4 Page No: 48 of 69 e g d e d n a B 1 x T

) m B d

(

l e v e L e g d e d n a B 2 x T

) m B d

(

l e v e L e g d e d n a B 3 x T

) m B d

(

l e v e L e g d e d n a B 4 x T

) m B d

(

l e v e L e g d e d n a B x T l a t o T

) m B d

(

l e v e L

) m B d

(

t i m L i

-60.4

-60.4

-60.4

-60.4

-46.3

-51.6

-51.6

-58.9

-54.2

-58.9

-61.0

-48.9

-48.9

-48.9

-54.1

-54.1

-54.1

-58.2

-58.2

-58.2

-58.2

-54.1

-48.9

-58.2

-54.1

-54.1

-62.3

-61.0

-61.0

-58.2

-48.9

-54.1

-58.2

-61.8

-61.8

-61.8

-50.4

-50.4

-57.9

-56.5

-57.9

-60.0

-48.5

-48.5

-53.0

-53.0

-53.0

-55.7

-55.7

-55.7

-55.7

-53.0

-48.5

-55.7

-53.0

-53.0

-60.5

-58.3

-58.3

-55.7

-48.5

-53.0

-55.7

-61.8

-61.8

-52.2

-59.1

-59.1

-62.0

-53.4

-53.4

-53.4

-57.9

-57.9

-57.9

-57.9

-57.9

-53.4

-53.4

-61.9

-59.9

-59.9

-57.9

-53.4

-57.9

-62.2

-51.4

-55.7

-47.1

-47.1

-47.1

-47.1

-55.2

-52.3

-52.3

-47.1

-47.1

-56.4

-54.0

-52.5

-51.5

-42.3

-43.9

-42.6

-45.4

-45.2

-44.8

-42.9

-44.9

-41.7

-41.7

-44.7

-44.7

-44.7

-42.0

-42.0

-42.0

-42.0

-43.5

-41.7

-43.3

-42.7

-44.7

-42.9

-43.4

-45.4

-42.0

-41.7

-44.7

-42.0

-41.83

-41.83

-41.83

-41.83

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

) B d

(

n g r a M i 14.6 12.2 10.7 9.6 0.8 2.5 1.1 3.9 3.7 3.3 1.4 3.4 0.2 0.2 3.2 3.2 3.2 0.5 0.5 0.5 0.5 2.0 0.2 1.9 1.2 3.2 1.4 1.9 3.9 0.5 0.2 3.2 0.5 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential 2 6 4 2 Custom EMC Test Report No: EDCS 15634526 CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps HT/VHT20, M0 to M7 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M16 to M23 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M16 to M23 HT/VHT20, M24 to M31 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M16 to M23 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M16 to M23 HT/VHT20 Beam Forming, M24 to M31 HT/VHT20 STBC, M0 to M7 HT/VHT20 STBC, M0 to M7 HT/VHT20 STBC, M0 to M7 1 2 3 4 1 2 3 4 2 3 4 1 2 2 3 3 3 4 4 4 4 2 2 3 3 3 4 4 4 4 2 3 4 4 4 4 4 4 4 4 4 7 9 10 4 4 4 4 4 4 4 4 4 4 7 4 9 6 4 10 7 5 4 4 4 4

-60.6

-60.6

-60.6

-60.6

-47.6

-50.6

-50.6

-53.6

-50.6

-57.2

-57.2

-47.1

-51.4

-51.4

-51.4

-51.4

-51.4

-53.8

-53.8

-53.8

-53.8

-51.4

-51.4

-55.2

-51.4

-51.4

-57.4

-55.2

-53.8

-53.8

-51.4

-51.4

-53.8

-62.1

-62.1

-62.1

-53.8

-53.8

-56.4

-53.8

-58.1

-58.1

-52.4

-52.4

-52.4

-52.4

-52.4

-55.0

-55.0

-55.0

-55.0

-52.4

-52.4

-56.8

-52.4

-52.4

-58.0

-56.8

-55.0

-55.0

-52.4

-52.4

-55.0

-60.9

-60.9

-52.7

-56.1

-58.7

-58.7

-53.2

-53.2

-53.2

-55.7

-55.7

-55.7

-55.7

-57.7

-53.2

-53.2

-59.6

-57.7

-55.7

-55.7

-53.2

-55.7

-63.2

-51.6

-56.8

-53.4

-53.4

-53.4

-53.4

-61.2

-57.8

-53.4

-53.4

-53.4

-56.6

-54.3

-52.4

-51.6

-43.6

-44.9

-43.4

-44.0

-41.9

-44.2

-41.6

-43.1

-44.9

-44.9

-43.5

-43.5

-43.5

-44.4

-44.4

-44.4

-44.4

-41.9

-44.9

-42.7

-41.5

-43.5

-42.8

-43.7

-43.4

-44.4

-44.9

-43.5

-44.4

-41.83

-41.83

-41.83

-41.83

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49

-41.49 14.8 12.4 10.6 9.7 2.1 3.4 1.9 2.5 0.4 2.7 0.1 1.6 3.4 3.4 2.0 2.0 2.0 2.9 2.9 2.9 2.9 0.4 3.4 1.2 0.0 2.0 1.3 2.2 1.9 2.9 3.4 2.0 2.9 Page No: 49 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 Conducted Bandedge Average, 2412 MHz, HT/VHT20, M0 to M7 Antenna A Antenna B Page No: 50 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 Conducted Bandedge Average, 2462 MHz, HT/VHT20 Beam Forming, M8 to M15 Antenna B Antenna A Antenna C Page No: 51 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526

) z H M

(

y c n e u q e r F 2 1 4 2 Mode CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps HT/VHT20, M0 to M7 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M16 to M23 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M16 to M23 HT/VHT20, M24 to M31 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M16 to M23 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M16 to M23 HT/VHT20 Beam Forming, M24 to M31 HT/VHT20 STBC, M0 to M7 HT/VHT20 STBC, M0 to M7 HT/VHT20 STBC, M0 to M7

) i B d

(

n i a G d e a t a n l n e e r r t o n C A 4 4 4 4 4 4 4 4 7 9 10 4 4 4 4 4 4 4 4 4 4 7 4 9 6 4 10 7 5 4 4 4 4 s h t a P x T 1 2 3 4 1 2 3 4 2 3 4 1 2 2 3 3 3 4 4 4 4 2 2 3 3 3 4 4 4 4 2 3 4 Page No: 52 of 69 e g d e d n a B 1 x T

) m B d

(

l e v e L e g d e d n a B 2 x T

) m B d

(

l e v e L e g d e d n a B 3 x T

) m B d

(

l e v e L e g d e d n a B 4 x T

) m B d

(

l e v e L e g d e d n a B x T l a t o T

) m B d

(

l e v e L

) m B d

(

t i m L i

-49.2

-49.2

-49.2

-49.2

-30.7

-34.3

-34.3

-44.7

-34.9

-44.7

-44.7

-40.6

-40.6

-40.6

-42.9

-42.9

-42.9

-47.7

-47.7

-47.7

-47.7

-42.9

-40.6

-47.7

-42.9

-42.9

-47.7

-49.1

-49.1

-47.7

-40.6

-42.9

-47.7

-46.7

-46.7

-46.7

-33.6

-33.6

-43.9

-39.6

-43.9

-48.4

-37.0

-37.0

-41.1

-41.1

-41.1

-45.9

-45.9

-45.9

-45.9

-41.1

-37.0

-45.9

-41.1

-41.1

-46.7

-46.3

-46.3

-45.9

-37.0

-41.1

-45.9

-50.6

-50.6

-36.4

-41.4

-41.4

-48.5

-44.1

-44.1

-44.1

-44.2

-44.2

-44.2

-44.2

-44.2

-44.1

-44.1

-50.0

-50.3

-50.3

-44.2

-44.1

-44.2

-48.7

-38.1

-39.1

-39.9

-39.9

-39.9

-39.9

-46.5

-44.1

-44.1

-39.9

-39.9

-45.2

-40.8

-39.8

-38.5

-26.7

-26.9

-25.8

-31.2

-26.6

-29.3

-27.3

-36.6

-31.4

-31.4

-33.8

-33.8

-33.8

-33.4

-33.4

-33.4

-33.4

-31.9

-31.4

-31.9

-31.8

-33.8

-31.5

-33.8

-35.8

-33.4

-31.4

-33.8

-33.4

-21.83

-21.83

-21.83

-21.83

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

) B d

(

n g r a M i 23.4 18.9 17.9 16.7 5.2 5.4 4.4 9.7 5.1 7.8 5.8 15.1 9.9 9.9 12.3 12.3 12.3 11.9 11.9 11.9 11.9 10.4 9.9 10.4 10.3 12.3 10.0 12.3 14.3 11.9 9.9 12.3 11.9 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential 2 6 4 2 Custom EMC Test Report No: EDCS 15634526 CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s CCK, 1 to 11 MB/s Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps Non HT20 Beam Forming, 6 to 54 Mbps HT/VHT20, M0 to M7 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M16 to M23 HT/VHT20, M0 to M7 HT/VHT20, M8 to M15 HT/VHT20, M16 to M23 HT/VHT20, M24 to M31 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M16 to M23 HT/VHT20 Beam Forming, M0 to M7 HT/VHT20 Beam Forming, M8 to M15 HT/VHT20 Beam Forming, M16 to M23 HT/VHT20 Beam Forming, M24 to M31 HT/VHT20 STBC, M0 to M7 HT/VHT20 STBC, M0 to M7 HT/VHT20 STBC, M0 to M7 1 2 3 4 1 2 3 4 2 3 4 1 2 2 3 3 3 4 4 4 4 2 2 3 3 3 4 4 4 4 2 3 4 4 4 4 4 4 4 4 4 7 9 10 4 4 4 4 4 4 4 4 4 4 7 4 9 6 4 10 7 5 4 4 4 4

-44.4

-44.4

-44.4

-44.4

-31.2

-33.8

-33.8

-37.4

-33.8

-42.9

-42.9

-34.9

-39.7

-39.7

-39.7

-39.7

-39.7

-42.2

-42.2

-42.2

-42.2

-39.7

-39.7

-43.6

-39.7

-39.7

-44.0

-43.6

-42.2

-42.2

-39.7

-39.7

-42.2

-46.8

-46.8

-46.8

-36.3

-36.3

-41.6

-36.3

-45.4

-45.4

-39.8

-39.8

-39.8

-39.8

-39.8

-42.8

-42.8

-42.8

-42.8

-39.8

-39.8

-45.7

-39.8

-39.8

-45.7

-45.7

-42.8

-42.8

-39.8

-39.8

-42.8

-46.2

-46.2

-37.6

-41.0

-46.2

-46.2

-41.4

-41.4

-41.4

-44.1

-44.1

-44.1

-44.1

-45.4

-41.4

-41.4

-47.5

-45.4

-44.1

-44.1

-41.4

-44.1

-48.0

-35.1

-38.4

-44.5

-44.5

-44.5

-44.5

-47.3

-44.3

-44.5

-44.5

-44.5

-40.4

-38.4

-36.9

-36.1

-27.2

-27.9

-26.8

-27.9

-24.9

-30.8

-26.0

-30.9

-32.7

-32.7

-31.5

-31.5

-31.5

-33.3

-33.3

-33.3

-33.3

-29.7

-32.7

-31.0

-29.5

-31.5

-29.9

-31.6

-32.3

-33.3

-32.7

-31.5

-33.3

-21.83

-21.83

-21.83

-21.83

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49

-21.49 18.6 16.6 15.1 14.3 5.7 6.4 5.3 6.5 3.4 9.3 4.6 9.4 11.2 11.2 10.0 10.0 10.0 11.8 11.8 11.8 11.8 8.2 11.2 9.5 8.0 10.0 8.4 10.2 10.8 11.8 11.2 10.0 11.8 Page No: 53 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 Conducted Bandedge Peak, 2412 MHz, Non HT20, 6 to 54 Mbps Antenna B Antenna A Antenna C Page No: 54 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 Conducted Bandedge Peak, 2462 MHz, Non HT20 Beam Forming, 6 to 54 Mbps Antenna A Antenna B Page No: 55 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 A.8 Conducted Bandedge (Non-Restricted Band) Emissions in non-restricted frequency bands - Test Requirement 15.247 / LP0002 (2018-01-10) (3.10.1.5) (2.8):

(d) In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 dB instead of 20 dB. Attenuation below the general limits specified in 15.209(a) is not required. In addition, radiated emissions which fall in the restricted bands, as defined in 15.205(a), must also comply with the radiated emission limits specified in 15.209(a) (see 15.205(c)). RSS-Gen 8.9 Except when the requirements applicable to a given device state otherwise, emissions from licence-exempt transmitters shall comply with the field strength limits shown in Table 4 and Table 5 below. Additionally, the level of any transmitter emission shall not exceed the level of the transmitters fundamental emission. RSS-Gen 8.10 (b) Unwanted emissions that fall into restricted bands of Table 6 shall comply with the limits specified in RSS-Gen; and (c ) Unwanted emissions that do not fall within the restricted frequency bands of Table 6 shall comply either with the limits specified in the applicable RSS or with those specified in this RSS-Gen. Emissions in non-restricted frequency bands - Test Method Ref. KDB 558074 D01 DTS Meas Guidance v05 ANSI C63.10: 2013 Emissions in non-restricted frequency bands - Conducted Test Procedure 1. Connect the antenna port(s) to the spectrum analyzer input. 2. Place the radio in continuous transmit mode 3. Configure Spectrum analyzer as per test parameters below (be sure to enter all losses between the transmitter output and the spectrum analyzer). 4. Use the marker function to determine the maximum spurs amplitude level. 5. Capture graphs and record pertinent measurement data. Ref. KDB 558074 D01 DTS Meas Guidance v05 section, 8.5 DTS emissions in non-restricted frequency bands, 8.7 DTS band-edge measurements ANSI C63.10: 2013 section 11.11.2, 11.11.3 Emissions in non-restricted frequency bands - Conducted Test parameters 11.11.2 Reference Level measurement Establish a reference level by using the following procedure:

a) Set instrument center frequency to DTS channel center frequency. b) Set the span to 1.5 x DTS bandwidth. c) Set the RBW = 100 kHz. d) Set the VBW 3 x RBW. e) Detector = peak. f) Sweep time = auto couple. g) Trace mode = max hold. h) Allow trace to fully stabilize. i) Use the peak marker function to determine the maximum PSD level. 11.11.3 Emission Level Measurement a) Set the center frequency and span to encompass frequency range to be measured. b) Set the RBW = 100 kHz. c) Set the VBW 3 x RBW. d) Detector = peak. e) Sweep time = auto couple. f) Trace mode = max hold. g) Allow trace to fully stabilize. h) Use the peak marker function to determine the maximum amplitude level. Page No: 56 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 Samples, Systems, and Modes System Number Description Samples 1 EUT Support S01 S02 Tested By :

Chris Blair Test Result : PASS Test Equipment See Appendix C for list of test equipment System under test Support equipment Date of testing:

09-Nov-18 - 13-Nov-18 Page No: 57 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 Non-Restricted Band Frequency

(MHz) 2412 2462 Mode CCK, 1 to 11 MB/s Non HT20, 6 to 54 Mbps HT/VHT20, M0 to M31 CCK, 1 to 11 MB/s Non HT20, 6 to 54 Mbps HT/VHT20, M0 to M31 Data Rate

(Mbps) 11 6 m0 11 6 m0 Conducted Bandedge Delta

(dB) 55.5 34.6 39.9 70.1 52.6 56.1 Limit

(dBc)

>30

>30

>30

>30

>30

>30 Margin

(dB) 25.5 4.6 9.9 40.1 22.6 26.1 Page No: 58 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 Conducted Bandedge Delta, 2412 MHz, Non HT20, 6 to 54 Mbps This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Page No: 59 of 69 Custom EMC Test Report No: EDCS 15634526 Appendix B: Radiated Emission Test Results Not included in this evaluation. These tests were performed at BACL. Page No: 60 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 Appendix C: List of Test Equipment Used to perform the test Test Equipment used for RF Conducted Tests Equip#

Manufacturer/ Model Description Last Cal Next Cal National Instruments CIS057476 Cisco NMN CIS055094 PXI-1042 CIS057237 National Instruments PXI-8115 CIS054686 National Instruments PXI-2796 CIS056091 National Instruments PXI-2796 CIS057245 National Instruments PXI-2799 CIS050721 Agilent N9030A-550 CIS054346 N5182B Keysight Fluke 175 CIS036772 Rack Chassis Embedded Controller 40 GHz Dual 6x1 Multiplexer

(SP6T) 40 GHz Dual 6x1 Multiplexer

(SP6T) Switch 1x1 PXA Signal Analyzer, 3Hz to 50GHz MXG X-Series RF Vector Signal Generator RMS multimeter CIS006325 Lufft 5063-33W CIS056329 Pasternack PE5019-1 Dial hygrometer Torque wrench Cal Not Required Cal Not Required Cal Not Required Cal Not Required Cal Not Required Cal Not Required 10-Apr-18 10-Apr-19 05 Oct 2018 22 May 2018 27 Aug 2018 28 Feb 2018 05 Oct 2019 22 May 2019 27 Aug 2019 28 Feb 2019 Test Item A1 thru A8 A1 thru A8 A1 thru A8 A1 thru A8 A1 thru A8 A1 thru A8 A1 thru A8 A1 thru A8 A1 thru A8 A1 thru A8 A1 thru A8 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Page No: 61 of 69 Custom EMC Test Report No: EDCS 15634526 Appendix D:

The following table defines abbreviations used within this test report. Abbreviation Key and Definitions Abbreviation Description Abbreviation Description F C Temp H Av Pk kHz MHz GHz Electro Magnetic Compatibility Electro Magnetic Interference Equipment Under Test Information Technology Equipment S/N Qty Test Assessment Schedule emf Electro Static Discharge Electric Fast Transient RMS Qp Engineering Document Control System Configuration Cisco Number (unique identification number for Cisco test equipment) Calibration European Norm International Electro technical Commission International Special Committee on Radio Interference Coupling/Decoupling Network Line Impedance Stabilization Network Protective Earth Ground Line 1 Line2 Line 3 Direct Current Uncorrected measurement value, as indicated by the measuring device Radio Frequency Signal Line Conducted Emissions Measurement distance Not Applicable Power Line Neutral Line Supply V kV V A A mS S V dB RF SLCE Meas dist N/A or NA P N S Appendix E: Photographs of Test Setups S m Spec dist SL L R AC EMC EMI EUT ITE TAP ESD EFT EDCS Config CIS#

Cal EN IEC CISPR CDN LISN PE GND L1 L2 L3 DC RAW Degrees Fahrenheit Degrees Celsius Temperature Serial Number Quantity Electromotive force Root mean square Quasi Peak Average Peak Kilohertz (1x103) MegaHertz (1x106) Gigahertz (1x109) Horizontal Vertical decibel Volt Kilovolt (1x103) Microvolt (1x10-6) Amp Micro Amp (1x10-6) Milli Second (1x10-3) Micro Second (1x10-6) Micro Second (1x10-6) Meter Specification distance Signal Line (or Telecom Line) Live Line Return Alternating Current This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Page No: 62 of 69 Custom EMC Test Report No: EDCS 15634526 Title: Radio Conducted Test Setup See Report Ref: R1811136-247 Page No: 63 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 Appendix F: Software Used to Perform Testing Cisco Internal LabView Radio Test Automation Software rev41, rev44, rev45 Cisco Internal LabView Radio Test Automation Report Generator Software rev13, rev14 Appendix G: Test Procedures Measurements were made in accordance with KDB 558074 - D01 DTS Meas Guidance v05 KDB 662911 - MIMO ANSI C63.4 2014 Unintentional Radiators ANSI C63.10 2013 Intentional Radiators EDCS # 1445042 EDCS # 1480386 Test procedures are summarized below FCC 2.4GHz Test Procedures FCC 2.4GHz RSE Test Procedures Appendix H:

The scope of accreditation of Cisco Systems, Inc. can be found on the A2LA web page at:

http://www.a2la.org/scopepdf/1178-01.pdf Scope of Accreditation (A2LA certificate number 1178-01) Page No: 64 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 Appendix I: Test Assessment Plan Compliance Test Plan (Excel) EDCS# 15683808 Target Power Tables EDCS# 11899590 Appendix J: Worst Case Justification Test modes were selected from the Target Power Tables EDCS# 11899590, representative of supported data rates, paths, antennas, and beamforming combinations. Appendix K: UUT Software Info from CLI AP00B7.7108.B200#show ver Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. Cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately. A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to export@cisco.com. This product contains some software licensed under the

"GNU General Public License, version 2" provided with ABSOLUTELY NO WARRANTY under the terms of

"GNU General Public License, version 2", available here:

http://www.gnu.org/licenses/old-licenses/gpl-2.0.html Page No: 65 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 This product contains some software licensed under the

"GNU Library General Public License, version 2" provided with ABSOLUTELY NO WARRANTY under the terms of "GNU Library General Public License, version 2", available here:

http://www.gnu.org/licenses/old-licenses/lgpl-2.0.html This product contains some software licensed under the

"GNU Lesser General Public License, version 2.1" provided with ABSOLUTELY NO WARRANTY under the terms of "GNU Lesser General Public License, version 2.1", available here:

http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html This product contains some software licensed under the

"GNU General Public License, version 3" provided with ABSOLUTELY NO WARRANTY under the terms of

"GNU General Public License, Version 3", available here:

http://www.gnu.org/licenses/gpl.html. This product contains some software licensed under the

"GNU Affero General Public License, version 3" provided with ABSOLUTELY NO WARRANTY under the terms of

"GNU Affero General Public License, version 3", available here:

http://www.gnu.org/licenses/agpl-3.0.html. Cisco AP Software, (ap1g6), [rch-ads-037:/nobackup/shaoxie/workspace5/router]

Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2015 by Cisco Systems, Inc. Compiled Fri Nov 2 14:01:55 CST 2018 ROM: Bootstrap program is U-Boot boot loader BOOTLDR: U-Boot boot loader Version AP00B7.7108.B200 uptime is 0 days, 0 hours, 8 minutes Last reload time : Wed Sep 26 19:49:21 UTC 2018 Last reload reason : reload command cisco AIR-AP2900I-B-K9 with 1931052/1534120K bytes of memory. Processor board ID KWC223301QV AP Running Image : 8.8.1.10 Primary Boot Image : 8.8.1.10 Backup Boot Image : 8.8.1.10 Primary Boot Image Hash:

e748370826e95c1b8b8b8b2fc369fbc6dc494ceafc57c988f282f31c42eccc676a07e281b174d9d90b8b59cfa15b1ca02d 71ef345a3363cc1c7f363cc6ca89b3 Backup Boot Image Hash:

0258f224157b54ade1af05b331dd80850ed106bbacdfdc5ee05118a6f973adbfb9331d779fee68d5f8a0020af829dfb828 f7f66a8f9761adfbe25876fa383e63 Page No: 66 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 1 Gigabit Ethernet interfaces 2 802.11 Radios Radio FW version : 0309210f11c4d71c07c3661854b97256 NSS FW version : sradhakr, Base ethernet MAC Address : 00:B7:71:08:B2:00 Part Number : 74-55083-01 PCA Assembly Number : 000-00000-00 PCA Revision Number : 01 PCB Serial Number : KWC223301QV Top Assembly Part Number : 074-120619-01 Top Assembly Serial Number : KWC223301QV Top Revision Number : 01 Product/Model Number : AIR-AP2900I-B-K9 AP00B7.7108.B200#

AP00B7.7108.B200#

AP00B7.7108.B200#devs EXITING CISCO SHELL. PLEASE EXECUTE EXIT IN DEVSHELL TO GET BACK TO CISCO SHELL. BusyBox v1.23.2 (2018-11-01 11:29:22 CST) built-in shell (ash) Welcome to Cisco. Usage of this device is governed by Cisco's End User License Agreement, available at:

http://www.cisco.com/c/en/us/td/docs/general/warranty/English/EU1KEN_.html. m00B77108B200:/# cat MERAKI_BUILD.extra Fri Nov 2 14:01:55 CST 2018 rch-ads-037

/nobackup/shaoxie/workspace5/router 09262017 c85 c86 c87

* compliance_chris fc_merge hgbtldr31 initclean master swsudi_commit base/axel-qca/firmware/IPQ8074/q6_fw.b00 | Bin 404 -> 404 bytes base/axel-qca/firmware/IPQ8074/q6_fw.b01 | Bin 392 -> 392 bytes Page No: 67 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 base/axel-qca/firmware/IPQ8074/q6_fw.b02 | Bin 4696 -> 4696 bytes base/axel-qca/firmware/IPQ8074/q6_fw.b03 | Bin 2989648 -> 2987856 bytes base/axel-qca/firmware/IPQ8074/q6_fw.b04 | Bin 953856 -> 953152 bytes base/axel-qca/firmware/IPQ8074/q6_fw.b05 | Bin 193668 -> 193668 bytes base/axel-qca/firmware/IPQ8074/q6_fw.b07 | Bin 7544 -> 7552 bytes base/axel-qca/firmware/IPQ8074/q6_fw.b08 | Bin 330837 -> 330645 bytes base/axel-qca/firmware/IPQ8074/q6_fw.b09 | Bin 262144 -> 262144 bytes base/axel-qca/firmware/IPQ8074/q6_fw.mdt | Bin 796 -> 796 bytes 10 files changed, 0 insertions(+), 0 deletions(-) svn base: c5729886f15bad4a5e4823f97f90962c2b676db9M commit: 4372b95ed5aadd828cb7a28ab4f355b7c3bace38 tree 1702f08529f671c35d95d2be1133f8ae5176078c recent commit: c5729886f15bad4a5e4823f97f90962c2b676db9 m00B77108B200:/#

m00B77108B200:/#

m00B77108B200:/#

m00B77108B200:/# show_cookie Part Number : 74-55083-01 Board Revision : 0 PCB Serial Number : KWC223301QV PCB Fab Part Number : 0-0000-00 Deviation Number : 0 MAC Address : 00:B7:71:08:B2:00 MAC Address Block Size : 4 Radio 0 MAC Address : 00:B7:71:08:B4:00 Radio 0 MAC Address Block Size : 16 Radio 1 MAC Address : 00:B7:71:08:B4:10 Radio 1 MAC Address Block Size : 16 PCA Assembly Number : 000-00000-00 PCA Revision Number : 01 Product/Model Number : AIR-AP2900I-B-K9 Top Assembly Part Number : 074-120619-01 Top Revision Number : 01 Top Assembly Serial Number : KWC223301QV RMA Test History : 00 RMA History : 00 RMA Number : 00-00-00-00 Device Type : 4C Max Association Allowed : 2 Radio(2.4G) Carrier Set : 0000 Radio(2.4G) Max Transmit Power Level : 100 Radio(2.4G) Antenna Diversity Support: 01 Radio(2.4G) Encryption Ability : 0002 Radio(5G) Carrier Set : 0029 Radio(5G) Max Transmit Power Level : 100 Radio(5G) Antenna Diversity Support : 01 Radio(5G) Encryption Ability : 0002 Page No: 68 of 69 This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Custom EMC Test Report No: EDCS 15634526 Radio(802.11g) Radio Mode : 255 PEP Product Identifier (PID) : AIR-AP2900I-B-K9 PEP Version Identifier (VID) : V01 System Flags : 00 Controller Type : 0000 Host Controller Type : 0000 Mfr Service Date : 2018.08.15-47:59:59 Radio(49) Carrier Set : 0000 Radio(49) Max Transmit Power Level : 100 Radio(49) Antenna Diversity Support : 01 Radio(49) Encryption Ability : 0002 Radio(58) Carrier Set : 0029 Radio(58) Max Transmit Power Level : 100 Radio(58) Antenna Diversity Support : 01 Radio(58) Encryption Ability : 0002 ACT2 ID : AP2900 Static AP Mode : 0 m00B77108B200:/#

m00B77108B200:/#

m00B77108B200:/#

m00B77108B200:/#

m00B77108B200:/# iwpriv wifi0 getRegdomain wifi0 getRegdomain:20 m00B77108B200:/# iwpriv wifi1 getRegdomain wifi1 getRegdomain:58 m00B77108B200:/#

End Of Document This document is uncontrolled. Please refer to the electronic copy within EDCS for the most up to date version. Cisco Systems, Inc. Company Confidential Page No: 69 of 69