DPH-SO16 Quick Install Guide Table of Contents CHAPTER 1 INTRODUCTION ............................................................................................. 1 Package Contents .............................................................................................................. 1 LEDs ................................................................................................................................... 2 CHAPTER 2 INITIAL INSTALLATION .............................................................................. 4 Procedure ........................................................................................................................... 4 CHAPTER 3 SPECIFICATIONS ........................................................................................... 6 General Specification ........................................................................................................ 6 Regulatory Requirements ................................................................................................. 7 Safety Information ............................................................................................................ 8 FCC Regulations: .............................................................................................................. 9 Copyright 2011. All Rights Reserved. Document Version: 1.0 All trademarks and trade names are the properties of their respective owners. i Chapter 1 Introduction 1 This Chapter provides an overview of the device's features and capabilities. This Access Point is a high-capacity enterprise Femtocell product that provides consumers with low cost calls using their 3G handsets and home broadband connection. This product will bring high-quality 3G coverage to the homes or offices. Just follow these simple instructions then you can take full advantage of the 3G network. Package Contents The following items should be included:
If any of the above items are damaged or missing, please contact your dealer immediately. Features Supports the Ubiquisys Enterprise FemtoEngine software Supports Band 2/5 WCDMA with GSM sniff capability Delivers UMTS applications to 3G client devices on indoor locations Supports Integrated Omni-directional antennae Designed for enterprise and hotspot types of deployments Up to 16 calls can be supported at the same time Maximum Tx Power of 24dBM Two Ethernet 10/100 ports for Internet connection and Power-over-Ethernet (PoE) function Single LED to indicate the status information External power supply Internal SIM socket 1 LEDs Front-mounted LED The device has 1 LED. Femto
(Red/Green) Green LED State On Fast Flashing Slow Flashing Sequence of two flashing lights Definition Power on. Initialization or temporarily out of service. One or more calls are currently active. No calls can be received currently. Red No Internet connection. Definition Product failure. LED State On Single Flashing light No router connection. Sequence of two flashing lights Sequence of three flashing lights Sequence of four flashing lights Sequence of five flashing lights Off - No power. Over-temperature. No SIM card detected. RF issue. Local interference/poor QOS. 2 Rear Panel GPS Connector
(Optional) PoE Port Computer Port Use a standard LAN cable (RJ45 connectors) to connect your PC to the The external antenna connector provides connection for an active external GPS antenna. Use a standard LAN cable (RJ45 connector) to connect the router. port. This button is used to reset the device to factory default settings. Connect the supplied power adapter here. Reset Power Port 3 Chapter 2 Initial Installation This Chapter covers the physical installation of the device. Procedure 2 1. Connect the supplied power adapter to the device. 2. Connect the router to the WAN(PoE) port on the device. 3. Plug the power supply into the main socket. 4. The green light will stop flashing when the device is read to use. It may take a few minutes to complete the process. If the green light does not stop flashing after 30 minutes, please call the operator for help. Wall Mounting The device can be either placed on a table using the stand provided or mounted on the wall. 1. Mark four points where you would like to mount the device. 2. Screw in 2/3 of the length of the mounting screws into the wall. 3. Hook the mounting holes located at the bottom of the device into the mounting screws. 4. Make sure the device is firmly fixed on the wall. 4 Initial Installation 5 Chapter 3 Specifications General Specification 3 2 x SMA-J type connectors for internal/external antennae 2 x 10/100 Ethernet ports IEEE 802.3/IEEE802.3i/IEEE802.3u/IEEE802.3x One 12V/2A, 100~240V Operating Temp. 0C to 40C Storage Temp. -5C to 45C Operating Humidity 5% to 90% Non-Condensing Storage Humidity 5% to 95% Non-Condensing One 1 Status LED 178mm(W)x235mm(H)x60mm(D) Connectivity SIM card slot Power Supply Operating Requirement Reset button LED Housing RF Specifications Parameter Frequency Bandwidth Beamwidth Power Rating UMTS UMTS band Band 2: DL: 1930-1990MHz, UL: 1850-1910MHz Band 5: DL: 869-894MHz, UL:
824-849MHz 5MHz Omni 20dBm Antenna Gain 2dbi Rx Sensitivity
-112dBm GSM Listen Mode GSM Band 2 DL: 1930 - 1990 MHz GSM Band 5 DL: 869 - 894 MHz 200KHz Omni N/A (Rx only) 2dbi
-112dBm 6 Regulatory Requirements CE Marking CE Mark EMC and Radio Compliance EMC EMF RoHS WEEE REACH Directive 1999/5/EC ETSI EN 301 908-1 V3.2.1:(2007-05) ETSI EN 301 489-1 V1.6.1 (2005-09) and Draft ETSI EN 301 489-1 V1.7.1 (2006-07) Version EN 301 489-1 V1.8.1 (2008-04) ETSI EN 301 489-23 V1.3.1: (2007-08) EN 50371:2002 EN62311:2008 and EN50385 European Directive 2002/95/EC (RoHS) EC Directive on Waste Electrical and Electronic Equipment
(WEEE) REACH compliant Product Reliability MTBF 65000 hrs @ 20C, 24hrs/day Product Life 5 years 7 Safety Information All instructions, warning and caution statements that accompany this equipment must be strictly followed at all times to ensure its safe use. Observe all warning and caution symbols that are fixed to this equipment. This electrical equipment is designed with the utmost care for the safety of those who install and use it. However, when using this device, basic safety pre-
cautions should always be followed to reduce the risk of fire and injury to persons, and the dangers of electric shock and static electricity. Do not cover the device or block the airflow to the device with any other objects. This product was qualified under test conditions that includ-
ed the use of the supplied cables between system components. To be in compliance with regulations, the user must use the cables supplied with the unit and install them properly. This includes the power adapter that is provided. Place the unit to allow for easy access when disconnecting the power adapter from the mains wall outlet. Operate this product only with the type of power source indicated on the marking label. If you are not sure of the type of power supplied to your home, consult your dealer or local electricity company. Do not use this product near water, for example a swimming pool or a bathroom. Keep the device away from excessive heat and humidity and keep the device free from vibration and dust. Wipe the unit with a clean, dry cloth. Never use cleaning fluid or similar chemicals. Do not spray cleaners directly on the unit or use forced air to remove dust. Avoid installing or using this product during an electrical storm. There may be remote risk of electric shock from lightning. During a lightning storm for added protection please unplug it from the wall outlet and disconnect all cables. This will prevent damage due to lightning and power surges. For safety reasons, only authorized service technicians should open the device. If the device is opened the warranty will become void. The device may affect medical equipment and so please take account of any technology restrictions with this equipment. This device, like other radio devices, emits radio frequency electromagnetic energy, but operates within the guidelines found in radio frequency safety standards and recommendations. It is recommended that the minimum operating distance from the installed Access Point to persons is 20cm. Ensure the Access Point is turned off when inserting or removing the SIM card. Do not bend or scratch your SIM card. Keep it say from static electricity, water and dirt. 8 FCC Regulations:
15.19 (a)(3) This device complies with part 15 of the FCC Rules. Operation is subject to the follow-
ing two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 15.21 Changes or modifications not expressly approved by the party responsible for compli-
ance could void the users authority to operate the equipment.
**************************************************************************************************
**************************
15.105 (b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interfer-
ence to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. RF Exposure Information This equipment complies with radio frequency (RF) exposure limits adopted by the Federal Communications Commission for an uncontrolled environment. This equip-
ment should be installed and operated with minimum distance 20 cm between the radiator & your body. 9