all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 3 |
|
Users Manual | Users Manual | 2.80 MiB | January 09 2015 | |||
1 2 3 | Cover Letter(s) | January 12 2015 | ||||||
1 2 3 | Cover Letter(s) | January 12 2015 | ||||||
1 2 3 | Test Report | January 12 2015 | ||||||
1 2 3 | Test Setup Photos | January 12 2015 | ||||||
1 2 3 | External Photos | January 12 2015 | ||||||
1 2 3 | ID Label/Location Info | January 12 2015 | ||||||
1 2 3 | Internal Photos | January 12 2015 | ||||||
1 2 3 | Cover Letter(s) | January 12 2015 | ||||||
1 2 3 | RF Exposure Info | January 12 2015 | ||||||
1 2 3 | Test Setup Photos | January 12 2015 | ||||||
1 2 3 | Test Report | January 12 2015 |
1 2 3 | Users Manual | Users Manual | 2.80 MiB | January 09 2015 |
Cisco IR829 Integrated Services Router Hardware Installation Guide August 2015 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 Text Part Number:
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS. THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY. The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense. The following information is for FCC compliance of Class B devices: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the equipment causes interference to radio or television reception, which can be determined by turning the equipment off and on, users are encouraged to try to correct the interference by using one or more of the following measures:
Increase the separation between the equipment and receiver. Reorient or relocate the receiving antenna.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help. Modifications to this product not authorized by Cisco could void the FCC approval and negate your authority to operate the product. The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCBs public domain version of the UNIX operating system. All rights reserved. Copyright 1981, Regents of the University of California. NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED AS IS WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE. IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R) Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental. Cisco IR829 Integrated Services Router Hardware Installation Guide 2015 Cisco Systems, Inc. All rights reserved. Cisco IR829 Integrated Services Router Hardware Installation Guide 1 C O N T E N T S C H A P T E R 1 Product Overview 1-1 General Description 1-1 LEDs 1-4 Memory 1-6 SKU Information 1-6 Hardware Features 1-6 Platform Features for Cisco IR829 1-7 Reset Button 1-8 Antennas 1-8 Antennas and Installation Scenarios 1-8 Supported Cisco Antennas and Cables 1-10 Power Supply 1-22 SFP Modules 1-22 C H A P T E R 2 Installing the Router 2-1 Equipment, Tools, and Connections 2-2 Items Shipped with your Router 2-2 Additional Items 2-2 Ethernet Devices 2-3 Installing the Router 2-3 Warnings 2-3 Accessing the SIM Cards 2-3 Installing Antennas 2-5 Mounting on a Wall, Table, or Other Flat Surface 2-5 Installing the Router Ground Connection 2-7 C H A P T E R 3 Connecting the Router 3-1 Preparing to Connect the Router 3-1 Preventing Damage to the Router 3-1 Connecting a PC, Server, or Workstation 3-2 Connecting a Terminal or PC to the Console Port 3-3 Cisco IR829 Integrated Services Router Hardware Installation Guide 1 Contents Connecting to DC Power 3-3 Plugs and Pin-Outs 3-4 Constructing a Power cable 3-4 Wiring the DC Power 3-5 Verifying Connections 3-6 C H A P T E R 4 Initial Configuration 4-1 Setup Command Facility 4-1 Verifying the Initial Configuration 4-4 Where To Go From Here 4-4 800 Series Documentation 4-4 Cisco IR829 Differences 4-5 LEDs 4-5 Software Bundle Installation 4-6 C H A P T E R 5 Guest Operating System (Guest OS) Installation and Configuration 5-1 Guest Operating System Overview 5-1 Prerequisites 5-2 Guidelines and Limitations 5-2 Default Settings 5-2 Installation and Upgrade 5-2 Configuring Cisco IOS 5-3 Configuring the IR829 Ethernet Interface 5-3 IPv6 Gigabit Ethernet 5-3 Enabling IPv4 Gigabit Ethernet 5-4 Configuring DHCP Pool 5-4 Configuring Guest OS Interface on Cisco IOS 5-5 Enabling Guest OS Console 5-6 Configuring Guest OS 5-6 Starting Guest OS 5-6 Accessing Guest OS Console 5-6 Setting the Root Password 5-7 Enabling Remote SSH Access 5-7 Configuring NAT 5-8 Troubleshooting 5-9 Checking Connectivity 5-9 Related Documentation 5-9 Cisco IR829 Integrated Services Router Hardware Installation Guide 2 C H A P T E R 6 Technical Specifications 6-1 Router Specifications 6-1 6-2 Contents Cisco IR829 Integrated Services Router Hardware Installation Guide 3 Contents Cisco IR829 Integrated Services Router Hardware Installation Guide 4 Preface This preface describes the objectives, audience, organization, and conventions of this guide and describes related documents that have additional information. It contains the following sections:
Objective, page 1
Audience, page 1
Organization, page 2
Conventions, page 2
Safety Warnings, page 3
Related Documentation, page 10
Searching Cisco Documents, page 10
Obtaining Documentation and Submitting a Service Request, page 10 Objective Audience This guide provides an overview and explains how to install, connect, and perform initial configuration for the Cisco IR829. This guide is intended for people who have a high level of technical ability, although they may not have experience with Cisco software. Cisco 829 Integrated Services Router Hardware Installation Guide 1 Organization Preface This guide is organized into the following chapters. Chapter Chapter 1 Name Chapter 1, Product Overview Chapter 2 Chapter 2, Installing the Router Chapter 3 Chapter 3, Connecting the Router Chapter 4 Chapter 4, Initial Configuration Chapter 5 Chapter 6 Chapter 5, Guest Operating System
(Guest OS) Installation and Configuration Chapter 6, Technical Specifications Description Describes the router models and the hardware features available. Lists the items shipped with the router, the equipment and tools necessary for installing the router, the safety warnings and guidelines, and the procedures for installing the router. Describes typical connections for the router, procedures for connecting the router to various devices, and how to verify the connections. Provides the procedures for initially configuring the router settings. Provides details Guest for Operating System (Guest OS) installation for the Cisco IR829. Provides the router, port, and cabling specifications. Conventions This section describes the conventions used in this guide. Note Means reader take note. Notes contain helpful suggestions or references to additional information and material. Caution This symbol means reader be careful. In this situation, you might do something that could result in equipment damage or loss of data. Tip Means the following information will help you solve a problem. The tip information might not be troubleshooting or even an action, but could be useful information. Cisco 829 Integrated Services Router Hardware Installation Guide 2 Preface Safety Warnings Warning IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071 SAVE THESE INSTRUCTIONS Waarschuwing BELANGRIJKE VEILIGHEIDSINSTRUCTIES Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen. BEWAAR DEZE INSTRUCTIES Varoitus TRKEIT TURVALLISUUSOHJEITA Tm varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin ksittelet laitteistoa, huomioi shkpiirien ksittelemiseen liittyvt riskit ja tutustu onnettomuuksien yleisiin ehkisytapoihin. Turvallisuusvaroitusten knnkset lytyvt laitteen mukana toimitettujen knnettyjen turvallisuusvaroitusten joukosta varoitusten lopussa nkyvien lausuntonumeroiden avulla. SILYT NM OHJEET Attention IMPORTANTES INFORMATIONS DE SCURIT Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraner des blessures ou des dommages corporels. Avant de travailler sur un quipement, soyez conscient des dangers lis aux circuits lectriques et familiarisez-vous avec les procdures couramment utilises pour viter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de scurit traduites qui accompagnent cet appareil, rfrez-vous au numro de l'instruction situ la fin de chaque avertissement. CONSERVEZ CES INFORMATIONS Cisco 829 Integrated Services Router Hardware Installation Guide 3 Preface Warnung WICHTIGE SICHERHEITSHINWEISE Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen fhren kann. Machen Sie sich vor der Arbeit mit Gerten mit den Gefahren elektrischer Schaltungen und den blichen Verfahren zur Vorbeugung vor Unfllen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen bersetzung in den bersetzten Sicherheitshinweisen, die zusammen mit diesem Gert ausgeliefert wurden. BEWAHREN SIE DIESE HINWEISE GUT AUF. Avvertenza IMPORTANTI ISTRUZIONI SULLA SICUREZZA Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento. CONSERVARE QUESTE ISTRUZIONI Advarsel VIKTIGE SIKKERHETSINSTRUKSJONER Dette advarselssymbolet betyr fare. Du er i en situasjon som kan fre til skade p person. Fr du begynner arbeide med noe av utstyret, m du vre oppmerksom p farene forbundet med elektriske kretser, og kjenne til standardprosedyrer for forhindre ulykker. Bruk nummeret i slutten av hver advarsel for finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten. TA VARE P DISSE INSTRUKSJONENE Aviso INSTRUES IMPORTANTES DE SEGURANA Este smbolo de aviso significa perigo. Voc est em uma situao que poder ser causadora de leses corporais. Antes de iniciar a utilizao de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos eltricos e familiarize-se com as prticas habituais de preveno de acidentes. Utilize o nmero da instruo fornecido ao final de cada aviso para localizar sua traduo nos avisos de segurana traduzidos que acompanham este dispositivo. GUARDE ESTAS INSTRUES Advertencia!
INSTRUCCIONES IMPORTANTES DE SEGURIDAD Este smbolo de aviso indica peligro. Existe riesgo para su integridad fsica. Antes de manipular cualquier equipo, considere los riesgos de la corriente elctrica y familiarcese con los procedimientos estndar de prevencin de accidentes. Al final de cada advertencia encontrar el nmero que le ayudar a encontrar el texto traducido en el apartado de traducciones que acompaa a este dispositivo. GUARDE ESTAS INSTRUCCIONES Cisco 829 Integrated Services Router Hardware Installation Guide 4 Preface Varning!
VIKTIGA SKERHETSANVISNINGAR Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utfr arbete p ngon utrustning mste du vara medveten om farorna med elkretsar och knna till vanliga frfaranden fr att frebygga olyckor. Anvnd det nummer som finns i slutet av varje varning fr att hitta dess versttning i de versatta skerhetsvarningar som medfljer denna anordning. SPARA DESSA ANVISNINGAR Cisco 829 Integrated Services Router Hardware Installation Guide 5 Preface Aviso INSTRUES IMPORTANTES DE SEGURANA Este smbolo de aviso significa perigo. Voc se encontra em uma situao em que h risco de leses corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos eltricos e familiarize-se com as prticas padro de preveno de acidentes. Use o nmero da declarao fornecido ao final de cada aviso para localizar sua traduo nos avisos de segurana traduzidos que acompanham o dispositivo. GUARDE ESTAS INSTRUES Advarsel VIGTIGE SIKKERHEDSANVISNINGER Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse. Fr du begynder arbejde p udstyr, skal du vre opmrksom p de involverede risici, der er ved elektriske kredslb, og du skal stte dig ind i standardprocedurer til undgelse af ulykker. Brug erklringsnummeret efter hver advarsel for at finde oversttelsen i de oversatte advarsler, der fulgte med denne enhed. GEM DISSE ANVISNINGER Cisco 829 Integrated Services Router Hardware Installation Guide 6 Preface Cisco 829 Integrated Services Router Hardware Installation Guide 7 Preface Warning When installing the product, please use the provided or designated connection cables/power cables/AC adaptors. Using any other cables/adaptors could cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the use of UL-certified cables (that have the UL shown on the code) for any other electrical devices than products designated by CISCO. The use of cables that are certified by Electrical Appliance and Material Safety Law (that have PSE shown on the code) is not limited to CISCO-designated products. Statement 371 Warning Read the wall-mounting instructions carefully before beginning installation. Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system. Statement 378 Warning To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables. Statement 1021 Cisco 829 Integrated Services Router Hardware Installation Guide 8 Preface Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024 Warning If the symbol of suitability with an overlaid cross appears above a port, you must not connect the port to a public network that follows the European Union standards. Connecting the port to this type of public network can cause severe personal injury or can damage the unit. Statement 1031 Warning Connect the unit only to DC power source that complies with the safety extra-low voltage (SELV) requirements in IEC 60950 based safety standards. Statement 1033 Warning When installing or replacing the unit, the ground connection must always be made first and disconnected last. Statement 1046 Warning Do not locate the antenna near overhead power lines or other electric light or power circuits, or where it can come into contact with such circuits. When installing the antenna, take extreme care not to come into contact with such circuits, because they may cause serious injury or death. For proper installation and grounding of the antenna, please refer to national and local codes (for example, U.S.:NFPA 70, National Electrical Code, Article 810, Canada: Canadian Electrical Code, Section 54). Statement 1052 Warning No user-serviceable parts inside. Do not open. Statement 1073 Warning Installation of the equipment must comply with local and national electrical codes. Statement 1074 Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030 Warning Read the installation instructions before connecting the system to the power source. Statement 1004 Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040 Warning The covers are an integral part of the safety design of the product. Do not operate the unit without the covers installed. Statement 1077 Cisco 829 Integrated Services Router Hardware Installation Guide 9 Preface Warning Hot surface. Statement 1079 Related Documentation
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
Cisco IOS Release Notes
Cisco 800 Series Integrated Services Routers Software Configuration Guide. Searching Cisco Documents To search an HTML document using a web browser, press Ctrl-F (Windows) or Cmd-F (Apple). In most browsers, the option to search whole words only, invoke case sensitivity, or search forward and backward is also available. To search a PDF document in Adobe Reader, use the basic Find toolbar (Ctrl-F) or the Full Reader Search window (Shift-Ctrl-F). Use the Find toolbar to find words or phrases within a specific document. Use the Full Reader Search window to search multiple PDF files simultaneously and to change case sensitivity and other options. Adobe Readers online help has more information about how to search PDF documents. Obtaining Documentation and Submitting a Service Request For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly Whats New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html Subscribe to the Whats New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS Version 2.0. Cisco 829 Integrated Services Router Hardware Installation Guide 10 C H A P T E R 1 Product Overview This chapter provides an overview of the features available for the Cisco IR829 Integrated Services Routers (ISRs) and contains the following sections:
General Description, page 1-1
SKU Information, page 1-6
Hardware Features, page 1-6 Note For compliance and safety information, see Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers. General Description The Cisco IR829 Integrated Services Router, part of the Cisco Integrated Services Routers Generation 2
(ISR G2) Family, is designed as a next generation ruggedized fixed form factor router. It is a a small-form factor cellular router targeting mobile/vehicle applications and includes WiFi to provide connectivity in non-carpeted IT spaces, Industrials, Utilities, Transportation, Infrastructure, Industrial M2M application, asset monitoring, Smart Grid, and Utility Application. Figure 1-1 shows the IR829. Figure 1-1 Cisco IR829 Integrated Services Router Cisco IR829 Integrated Services Router Hardware Installation Guide 1-1 General Description Chapter 1 Product Overview Figure 1-2 shows the front panel details of the Cisco IR829. Figure 1-2 Cisco IR829 Front Panel CELLULAR 0 AUX Limited Modularity Slot 1 2 3 Gigabit WAN 5 Serial Ports 6 USB-A Port 7 Power Input, Battery, and Ignition connector. Refer to the DC Power section for pin-outs. 4 Gigabit LAN/PoE 8 WLAN ANT0 5GHz Figure 1-3 shows the back panels details of the Cisco IR829. Figure 1-3 Cisco IR829 Back Panel 1 WLAN ANT 0 2.4GHz 2 WLAN ANT 1 5GHz 3 SIM Door Assembly 4 GPS SMA 5 SIM connection 1 (SIM connection 0 is above) 6 WLAN ANT 1 2.4GHz 7 CELLULAR 0 MAIN Note Behind the SIM Door Assembly, there is a reset switch, Mini USB Debug connection, and Dual SIM slots. See Figure 1-4 for details Cisco IR829 Integrated Services Router Hardware Installation Guide 1-2 Chapter 1 Product Overview General Description Figure 1-4 Behind the SIM Door Figure 1-5 shows the top of the Cisco IR829. Figure 1-5 Cisco IR829 Top Cover Figure 1-6 shows the LED detail. Cisco IR829 Integrated Services Router Hardware Installation Guide 1-3 General Description Chapter 1 Product Overview Figure 1-6 Cisco IR829 LED Detail The following section shows a detailed description of the LEDs. LEDs The following table describes the LEDs for the Cisco IR829. Table 1-1 LED Descriptions LED PWR Activity Power Status Description Off No power Green Steady on Normal operation Green Flashing Boot up phase or in ROM Monitor mode Yellow Steady on System shutdown due to under or over voltage conditions Yellow Flashing System has an error, but has network connectivity Off No -54V PoE power supply detected or no PoE board installed Green Steady on 53.5V POE power supply good and all powered port operating normally Yellow Steady on 53.5V POE power supply good, but one or more POE ports has a fault. Off No VPN tunnel Steady on At least one VPN tunnel is up Off No link Steady on Link is up Blink Transmitting and Receiving data POE POE Power Supply Status VPN VPN GE0 WAN Link Status Cisco IR829 Integrated Services Router Hardware Installation Guide 1-4 Chapter 1 Product Overview General Description Table 1-1 LED Descriptions (continued) LED GPS Activity GPS Status Description Off GPS not configured On GPS configured Slow Flash GPS Acquiring in Standalone GPS Fast Flash GPS Acquiring in Assisted GPS Note Slow Flash is defined as the LED will be on for 0.25 seconds and off for 0.75 seconds. Fast Flash s defined as the LED will be on for 0.25 seconds and off for 0.25 seconds. Link Status/POE Status Off No link MOD Ethernet LAN Switch Ports GE1-GE4]
Single LED per Port WLAN 2.4GHz 5GHz CELLULAR0/
CELLULAR1 ACT CELLULAR0/
CELLULAR1 RSSI SIM0/SIM1 Sim cards Figure 1-7 RSSI LED Green Steady on Link is up Green Blink Transmitting and Receiving data Yellow POE Fault, implies no link Off Radio is down (no SSID configured) Flashing Green Bootloader, IOS Ethernet Initialization, IOS Start Up after system initialization. Green to Red to Yellow Discovery/Join process. Rapid Flashing Green Joined to a controller Steady Green One wireless client is associated. Off Module not powered on On Module is powered on and connected but not transmitting or receiving Slow Blink Module is powered on and searching for connection Fast Blink Module is transmitting or receiving. The RSSI LEDs are a 3 LED bar graph to indicate signal strength. Their functionality is described in the RSSI LED figure below. Off No USIM Green USIM installed and active RSSI RSSI (2) Green
<110dBm Off
-110 90dBm Off RSSI (1) Green Off Off RSSI (0) Green/Yellow Off On - Yellow Cisco IR829 Integrated Services Router Hardware Installation Guide 1-5 SKU Information Chapter 1 Product Overview RSSI (2) RSSI
-90 75dBm Off
-75 60dBm Off
>60dBm On - Green RSSI (1) Off On - Green On - Green RSSI (0) On - Green On - Green On - Green Memory The Cisco IR829 uses flash memory and main memory. The flash memory contains the Cisco IOS software image and the boot flash contains the ROMMON boot code. All memory components are factory default and not upgradeable by the end user. Table 1-2 shows the memory allocation. Table 1-2 Cisco IR829 Memory Memory DDR Boot ROM System Flash SKU Information Capacity 2GB 16MB 4GB Table 1-1 lists the different SKUs available for the Cisco ISRs. All SKUs support external antenna. Table 1-3 Supported SKUs for Cisco IR829s SKU ID IR829GW-LTE-VZ-
AK9 IR829GW-LTE-NA-
AK9 IR829GW-LTE-GA-
EK9 IR829GW-LTE-GA-
ZK9 Description C829 Hardened WAN GE 4G LTE secure platform multi-mode Verizon LTE/DoRa with 802.11n, FCC compliant C829 Hardened WAN GE 4G LTE secure platform multi-mode ATT and Canada LTE/HSPA+ with 802.11n, FCC compliant C829 Hardened WAN GE 4G LTE secure platform multi-mode Global
(Europe) LTE/HSPA+ with 802.11n, ETSI Compliant C829 Hardened WAN GE 4G LTE secure platform multi-mode Global
(Australia) LTE/HSPA+ with 802.11n, Australia Compliant Hardware Features This section provides an overview of the following hardware features for the Cisco IR829.
Platform Features for Cisco IR829, page 1-7
Antennas, page 1-8 Cisco IR829 Integrated Services Router Hardware Installation Guide 1-6 Chapter 1 Product Overview Hardware Features
Reset Button, page 1-8
Supported Cisco Antennas and Cables, page 1-10
Power Supply, page 1-22 Platform Features for Cisco IR829 The following lists the hardware platform features for the Cisco IR829.
Intel Atom Dual-Core Rangeley CPU, 1250 MHz
2GB DDR3 memory capacity
64MB SPI BIOS NOR flash
8GB (4GB usable) eMMC bulk storage flash
4-port GE LAN switch, optional PoE 802.3at (30W max)
WAN 1 GE SFP
WWAN /WLAN mini PCIe slots for 3G/4G/LTE modems, dual SIM Single 802.11 a/b/n WiFi radio
Optional Limited Modularity (BYOI) slot'
One RJ45 RS232 port
One RJ45 RS232/RS485 Serial port
One USB 2.0 Type A external port
One mini USB connector
Lithium Ion battery backed-up RTC
External Reset/Recovery Push Button
External Power Direct-wire 12/24VDC vehicle charging system input (9 32VDC) 4-pin locking power connector
External GPS SMA Connector
Six External TNC/RP-TNC connectors (depends on the configuration) for connection to WWAN
/WLAN internal modules
Class A EMC compliance
RoHS6 compliance
Mechanical Fanless operation Form-factor with no cable cover = 11.00 x 7.70 x 1.73 (WDH) Horizontal, Vertical, wall, floor, cabinet-mount and shelf-mount Cisco IR829 Integrated Services Router Hardware Installation Guide 1-7 Antennas Reset Button Chapter 1 Product Overview The Reset button resets the router configuration to the default configuration set by the factory. To restore the router configuration to the default configuration set by the factory, use a standard size #1 paper clip with wire gauge 0.033 inch or smaller and simultaneously press the reset button while applying power to the router. Note The rear cover must be removed to expose the reset switch. Antennas The IR829 has 4 x Wi-Fi antennas (2.4GHz & 5GHz) + 2 antennas for cellular RP-TNC bulkhead connectors. Standard antennas are:
Two multiband swivel-mount dipole antennae (ANT-4G-DP-IN-TNC) and one extender
(4G-AE010-R) are included with all the IR829s.
WLAN: Three Cisco Multiband Swivel-Mount Dipole Antennae. (AIR-ANTM2050D-R) are included for all IR829 SKUs that have WLAN functionality. For detailed information about Cisco Antennas, please refer to the following guides:
Connected Grid Antennas Installation Guide:
http://www.cisco.com/c/en/us/td/docs/routers/connectedgrid/antennas/installing/cg_antenna_install_gu ide.html Antennas for the Cisco 800 Series Routers:
http://www.cisco.com/c/en/us/support/routers/800-series-routers/products-installation-guides-list.html Antennas and Installation Scenarios Note Before choosing your antenna type and installation scenario, read through the following information. Coexistence of radio standards:
When operating and planning installation of products with WiFi, 4G LTE, and GPS wireless standards coexisting on the IR829 platform, the user needs to provision greater than 15dB isolation between the WiFi and LTE antennas at all frequencies of 4G LTE and WiFI operation for minimum impact to performance. Ideally, isolation should be 20-25dB or more. Specifically, users should not install 4G LTE dipoles and WiFi dipoles on the chassis at the same time, since doing so would generally result in less than 15dB isolation and may have a strong impact on performance depending on frequency bands in question. Vehicular 5-in-1 and 2-in-1 installation and deployment notes In the section that follows, the 5-in-1 antenna refers to ANT-5-4G2WL2G1-O, and 2-in-1 antenna refers to ANT-2-WLAN-D-O. Cisco IR829 Integrated Services Router Hardware Installation Guide 1-8 Chapter 1 Product Overview Antennas Figure 1-8 Sample Installation Installation Users need to provision a 8 x 8" flat mounting surface with a mounting hole on the roof of the vehicle for the 5-in-1 antenna, and a 6 x 6" flat mounting surface with a mounting hole for the 2-in-1 WiFi antenna. Without a flat mounting surface, the antenna will not meet IP67 standards and may have reduced service life. Ground plane Cisco recommends having a 1 foot ground plane under both the 5-in-1 and 2-in-1 antennas. In case of a metal vehicle roof, the roof itself shall be the ground plane. While Cisco has investigated the effects of ground plane and no ground plane, wireless performance was certified with the 1 foot ground plane. Isolation between 5-in-1 and 2-in-1 antennas Cisco recommends 18" inch spacing between the 5-in-1 and the 2-in-1 antenna centers for optimal isolation. Cisco recommends routing the 2.4GHz WLAN ports of the IR829 to the 2-in-1 antenna, and the 5GHz ports to the 5-in-1 antenna to optimize isolation between WiFi 2.4 GHz and cellular 4G LTE. The 5-in-1 antenna has been fully optimized for WiFI and cellular LTE coexistence and isolation. Connecting the 2.4GHz WiFi signals to a separate antenna simply allows to user to optimize the antenna isolation further. Both the 5-in-1 and 2-in-1 are dual band WiFi capable and fully support both 2.4 GHz or 5GHz WLAN signals. Cisco IR829 Integrated Services Router Hardware Installation Guide 1-9 Antennas Chapter 1 Product Overview MIMO ports on 5-in-1 and 2-in-1 Cellular and WLAN ports on the 5-in-1 and 2-in-1 antennas support MIMO technology. MIMO brings significant improvements in throughput and robustness of the wireless link in fading channels. Users choosing to connect only one wireless port on MIMO capable products are giving up significant wireless performance in both throughput and robustness of the link.
The individual 4G antenna cables on the 5-in-1 antenna can be connected to either cellular port of IR829. There is no one-to-one assignment requirement.
The individual WLAN antenna cables on the 5-in-1 antenna and the 2-in-1 antenna can be connected to any WLAN port of IR829. There is no one to one assignment requirement. The following section shows some examples of different installation scenarios. Supported Cisco Antennas and Cables Table 1-4 lists the supported 4G/LTE Radio Modules/Cables/Antennas for Cisco IR829. Table 1-4 4G/LTE Radio Modules/Cables/Antennas Use Case 4G/LTE Case 1:
1' 2', 5', 10', 15' or 20'
cable to mast mounted antenna, Stick Omni or Directional Flat Panel antenna 4G/LTE Case 2:
Radio Module IR829GW-LTE
-GA-EK9 IR829GW-LTE
-GA-ZK9 IR829GW-LTE
-NA-AK9 IR829GW-LTE
-VZ-AK9 2x TNC(f) IR829GW-LTE
-GA-EK9 IR829GW-LTE
-GA-ZK9 IR829GW-LTE
-NA-AK9 IR829GW-LTE
-VZ-AK9 2x TNC(f) Lightning Arrestor or Adapter None Indoor Cable None Router located in outdoor protective enclosure Outdoor Cable RA-TNC(m) to N(m), LMR-400-DB, 20', qty 2
37-1378-01
"CAB-L400-2 0-TNC-N R/A-TNC(m) to N(m), LMR-240-FR/CMR, 2, qty 2
37-100707-01 Note Not available from Cisco Antenna 2x 4G Omni Stick, Standard Perf, 10 2dBi, 1x N(f) each
07-1171-01
ANT-4G-OMNI-O UT-N 1x 4G Panel Antenna, 2x N(f) each
07-1172-01
ANT-4G-PNL-OUT
-N 1x 4G Panel Antenna, 2x N(f) each
07-1172-01
ANT-4G-PNL-OUT
-N Cisco IR829 Integrated Services Router Hardware Installation Guide 1-10 Chapter 1 Product Overview Antennas Table 1-4 4G/LTE Radio Modules/Cables/Antennas Lightning Arrestor or Adapter Outdoor Cable Antenna Use Case Radio Module Indoor Cable R/A-TNC(m) to N(m), LMR-240-FR/CMR, 1', qty 2
37-100705-01 Note Not available from Cisco R/A-TNC(m) to N(m), LMR-240-FR/CMR, 5', qty 2
37-100717-01 Note Not available from Cisco R/A-TNC(m) to N(m), LMR-240-FR/CMR, 10', qty 2
37-100754-01 Note Not available from Cisco R/A-TNC(m) to N(m), LMR-240-FR/CMR, 15', qty 2
37-100757-01 Note Not available from Cisco R/A-TNC(m) to N(m), LMR-240-FR/CMR, 20', qty 2
37-100758-01 Note Not available from Cisco Cisco IR829 Integrated Services Router Hardware Installation Guide 1-11 Antennas Chapter 1 Product Overview Table 1-4 4G/LTE Radio Modules/Cables/Antennas Lightning Arrestor or Adapter None Outdoor Cable None Antenna Qty 2 x 4G Indoor Swivel Mount Dipole, 0 dBi, TNC(m), white
07-1174-01
ANT-4G-DP-IN-TN C None None Qty 2 x 4G Indoor Swivel Mount Dipole, 0 dBi, TNC(m), black
07-1137-01
4G-LTE-ANTM-D Use Case 4G/LTE Case 3:
Front Panel Swivel Mount 4G-LTE dipoles 4G/LTE Case 4:
Front Panel Swivel Mount 4G-LTE dipoles Radio Module IR829GW-LTE
-GA-EK9 IR829GW-LTE
-GA-ZK9 IR829GW-LTE
-NA-AK9 IR829GW-LTE
-VZ-AK9 2x TNC(f) IR829GW-LTE
-GA-EK9 IR829GW-LTE
-GA-ZK9 IR829GW-LTE
-NA-AK9 IR829GW-LTE
-VZ-AK9 2x TNC(f) Indoor Cable None OR qty 2x PID: 4G-AE010-R CPN: 07-1144-01 10ft extension base for TNC dipole antennas OR qty 2x PID: 4G-AE015-R CPN: 07-1145-01 15ft extension base for TNC dipole antennas None OR qty 2x PID: 4G-AE010-R CPN: 07-1144-01 10ft extension base for TNC dipole antennas OR qty 2x PID: 4G-AE015-R CPN: 07-1145-01 15ft extension base for TNC dipole antennas Cisco IR829 Integrated Services Router Hardware Installation Guide 1-12 Chapter 1 Product Overview Antennas Table 1-4 4G/LTE Radio Modules/Cables/Antennas Use Case 4G/LTE Case 5:
2x ceiling mount 4G-LTE antennas Radio Module IR829GW-LTE
-GA-EK9 IR829GW-LTE
-GA-ZK9 IR829GW-LTE
-NA-AK9 IR829GW-LTE
-VZ-AK9 2x TNC(f) GPS Case 1:
GPS Antenna with Integrated 15' coax cable, Mounted to top of Utility Cabinet Roof
SMA(f), qty 1 Indoor Cable None Lightning Arrestor or Adapter None Outdoor Cable None Antenna Qty 2 x 4G Indoor omni-directional Ceiling Mount 2 dBi,
07-1121-01
4G-ANTM-OM-C M OR Qty 2 x 4G Dipole Ceiling Mount 2 dBi
07-1174-01
ANT-4G-DP-IP-TN C GPS Antenna. Need one with integrated coax cable and SMA(m) connector, 17ft, outdoor, IP67 qty 1
07-1183-01
GPS-ACT-ANTM-S MA=
Cisco IR829 Integrated Services Router Hardware Installation Guide 1-13 Antennas Chapter 1 Product Overview Table 1-5 lists the supported Single Band Cisco WiFi antenna for the Cisco IR829. Table 1-5 Supported Single Band Cisco WiFi Antenna Lightning Arrestor or Adapter N/A Outdoor Cable N/A Use Case WiFi Use Case 2:
Single Band, Front Panel Mounted Antennas Radio Module Dual Band Simultaneous 802.11n 2x2 MIMO WiFi Indoor Cable N/A Connectors:
4x RP-TNC (jack) WiFi Use Case 3:
Single Band, Single Element, Ceiling Mounted Antennas Dual Band Simultaneous 802.11n 2x2 MIMO WiFi Connectors:
4x RP-TNC (jack) WiFi Use Case 4:
2.4 GHz, Dual Element, 5 GHz Single Element, Ceiling Mounted Antennas Dual Band Simultaneous 802.11n 2x2 MIMO WiFi Connectors: 4x RP-TNC (jack) None N/A N/A OR RP-TNC (jack) to RP-TNC
(plug), Outdoor rated, Plenum rated, 0.195"
O.D. cable, 5' long
37-1067-01
AIR-CAB005 PL-R None N/A N/A OR RP-TNC(jack) to RP-TNC(plug), Outdoor rated, Plenum rated, 0.195 O.D. cable, 5 long 37-1067-01 AIR-CAB005PL
-R Cisco IR829 Integrated Services Router Hardware Installation Guide 1-14 Antenna 2x Single Band, Swivel Mount Omni, RP-TNC(plug), 2.2dBi @ 2.4 GHz 07-1056-02 AIR-ANT4941 2x Single Band, Swivel Mount Omni, RP-TNC(plug), 3.5dBi @ 5 GHz
07-1055-02
AIR-ANT5135 2x Single Band, Ceiling Mount Omni, 36 LONG RG-58 cable with RP-TNC
(plug), 5.2dBi @ 2.4 GHz
74-1868-01
AIR-ANT1728 2x Single Band, Ceiling Mount Omni, 36" LONG RG-58 cable with RP-TNC
(plug), 5.2dBi @ 5 GHz
74-3733-01
AIR-ANT5160V-R 1x Single Band, Ceiling Mount Omni, Dual Element, 36" LONG RG-58 cable with RP-TNC, 2.0dBi @ 2.4 GHz
800-33316-01
AIR-ANT24020V-R 2x Single Band, Ceiling Mount Omni, 36" LONG RG-58 cable with RP-TNC
(plug), 5.2dBi @ 5 GHz
74-3733-01
AIR-ANT5160V-R Chapter 1 Product Overview Antennas Table 1-5 Supported Single Band Cisco WiFi Antenna(continued) Use Case WiFi Use Case 5:
Single Band, Dual Element, Wall Mounted Antennas Radio Module Dual Band Simultaneous 802.11n 2x2 MIMO WiFi Indoor Cable None Connectors:
4x RP-TNC (jack) Antenna 1x Single Band, Dual Element, Wall Mount Patch, 18" LONG RG-58 cable with RP-TNC, 6.5dBi @ 2.4 GHz
800-27066-01
AIR-ANT2465P-R 1x Single Band, Dual Element, Wall Mount Omni, 18" LONG RG-58 cables with RP-TNC, 4.5dBi @ 5 GHz (INDOOR ONLY)
800-25716-06
AIR-ANT5145V-R OR 1x Single Band, Dual Element, Wall Mount Patch, 18" LONG RG-58 cables with RP-TNC, 7.0dBi @ 5 GHz (INDOOR/OUTDOOR)
800-25718-05
AIR-ANT5170P-R Lightning Arrestor or Adapter None Outdoor Cable None OR OR RP-TNC lightning arrestor, qty 4
74-3722-
01
AIR-AC C245L A-R RP-TNC(plug) to RP-TNC(jack) LMR-400-DB, 5'
qty 4
37-0766-01
AIR-CAB005LL
-R OR RP-TNC(plug) to RP-TNC(jack) LMR-400-DB, 20'
qty 4
72-2760-02
AIR-CAB020LL
-R OR RP-TNC(plug) to RP-TNC(jack) LMR-400-DB, 50'
qty 4
72-2761-02
AIR-CAB050LL
-R OR RP-TNC(plug) to RP-TNC(jack) LMR-600-DB, 100'
qty 4
72-2766-02
AIR-CAB100U LL-R Cisco IR829 Integrated Services Router Hardware Installation Guide 1-15 Antennas Chapter 1 Product Overview Table 1-5 Supported Single Band Cisco WiFi Antenna(continued) Indoor Cable Use Case WiFi Use Case 7:
Single Band, Dual Element, Wall Mounted Patch, Indoor/ Outdoor Antennas Radio Module Dual Band Simultaneous 802.11n 2x2 MIMO WiFi Connectors:
4x RP-TNC (jack) Lightning Arrestor or Adapter N(f) to N(f), Outdoor Cable RP-TNC(plug) to N(m)-R/A RF-adapter LMR-240-DB, 5'
qty 4 qty 4
37-1492-01
AIR-CAB005LL
-R-N
29-1008 18-01
AIR-AC C370-
NF-N F Antenna 1x Single Band, Dual Element, Wall Mount Patch, 18" LONG RG-58 cable with N(m), 13dBi @ 2.4 GHz
07-1193-01
AIR-ANT2413P2M-N 1x Single Band, Dual Element, Wall Mount Patch, 18" LONG RG-58 cable with N(m), 14dBi @ 5 GHz
07-1192-01
AIR-ANT5114P2M-N Table 1-6 lists the supported Dual Band Cisco WiFi antenna for Cisco IR829. Table 1-6 Supported Dual Band Cisco WiFi Antenna Use Case WiFi Use Case 8:
Dual Band Front Panel Mounted Antennas Radio Module Dual Band Simultaneous 802.11n 2x2 MIMO WiFi Connectors:
2x RP-TNC (jack) Indoor Cable N/A Lightning Arrestor or Adapter N/A Outdoor Cable N/A Antenna 2x Dual Band, Swivel Mount Omni, RP-TNC(plug), 2dBi
@ 2.4 GHz, 4dBi @ 5 GHz
07-1146-01
AIR-ANT2524DB-R Cisco IR829 Integrated Services Router Hardware Installation Guide 1-16 Chapter 1 Product Overview Antennas Table 1-6 Supported Dual Band Cisco WiFi Antenna(continued) Indoor Cable N/A Lightning Arrestor or Adapter N/A Outdoor Cable N/A Use Case WiFi Use Case 9:
Dual Band, Dual Element, Wall Mounted Antennas Radio Module Dual Band Simultaneous 802.11n 2x2 MIMO WiFi Connectors:
2x RP-TNC (jack) WiFi Use Case 10:
Dual Band Front Panel Mounted Antennas N/A Dual Band Simultaneous 802.11n 2x2 MIMO WiFi Connectors:
2x RP-TNC (jack) N(f) to N(f), RP-TNC(plug) to N(m)-R/A RF-adapter LMR-240-DB, 5'
qty 2 qty 2
37-1492-01
AIR-CAB005LL
-R-N
29-1008 18-01
AIR-AC C370-
NF-N F Antenna 1x Dual Band, Dual Element per Band, Omni, 18" LONG RG-58 cables with RP-TNC
(plug), 2.0dBi @ 2.4 GHz (2 ports), 3.0dBi @ 5 GHz (2 ports)
07-1071-02
AIR-ANT2451V-R 2400-2484MHz, 5150-5875MHz, WiFi, omni-directional 4 dBi
(2.4 GHz) 7 dBi (5 GHz) stick antenna indoor /
outdoor with type N(m) connector, qty 2 Antennas are IP66, IP67 and
-40 to +70C.
07-1126-01
AIR-ANT2547V-N=
White OR qty 2
07-1285-01
AIR-ANT2547VG-N=
Gray Table 1-7 lists the supported 7 in 1 antenna configuration for transportation for Cisco IR829. Note In the following use cases, Lightning Arrestors are not required, and the Radio Modules are:
IR829GW-LTE-GA-EK9 IR829GW-LTE-GA-ZK9 IR829GW-LTE-NA-AK9 IR829GW-LTE-VZ-AK9 Table 1-7 7 in 1 Antenna Configuration for Transportation Cisco IR829 Integrated Services Router Hardware Installation Guide 1-17 Antennas Chapter 1 Product Overview Cisco IR829 Integrated Services Router Hardware Installation Guide 1-18 Chapter 1 Product Overview Use Case Transportation Use Case 1:
7 x RF ports, with the IR829 deployed in a transportation application.
(Default Configuration) Quinta 5-in-1 antenna AND a WiFi 2-in-1 antenna to utilize all 7 ports. The 5-in1 Quinta antenna and the 2-in1 WiFi antennas need to be separated 18"
between mounting hole centers of the two antennas. Extension Cable No extension cables are required if the IR829 is located within ~1.0ft of 5-in-1 antenna, and ~2.0ft of WiFi 2-in-1 antenna. If these conditions are not met, this deployment requires the following extension cables:
Cellular extension cables (2 ports) Qty 2X LMR-400-DB TNC(m)-R/A -
TNC(f), 5ft
4G-CAB-LMR400-5
37-100842-01 OR Qty 2X LMR-400-DB TNC(m)-R/A -
TNC(f), 10ft
G-CAB-LMR400-10
37-100843-01 OR Qty 2X LMR-400-LLPL plenum / indoor only TNC(m)-R/A - TNC(f), 20ft
4G-CAB-ULL-20
37-1401-01 AND Antennas Antenna Quinta 5 element 5-in-1 transportation antenna, black radome color, 2x 4G cellular, 2x dual band WiFi, 1xGPS
ANT-5-4G2WL2G1-O
07-100261-01 Has the following integrated cables:
qty 2 x cellular, LMR-195, 2ft long, TNC(m) qty 2 x WiFi, 2ft long, LMR-195 RPTNC (plug) qty 1 x GPS, RG-174, 17ft long, SMA(m) AND WiFi 2-in-1 2 element 2 in 1 transportation antenna, black radome color, 2x dual band WiFi
ANT-2-WLAN-D-O
07-100265-01 Has the following integrated cables:
qty 2 x WiFi, 3ft long, LMR-240 RPTNC(plug) Cisco IR829 Integrated Services Router Hardware Installation Guide 1-19 Antennas Use Case Transportation Use Case 1 Continued:
Chapter 1 Product Overview Extension Cable WiFi 2.4 GHz / 5GHz extension cables Antenna
(4 ports, can mix and match lengths per installation requirements if needed) Qty 4x LMR-400-DB RPTNC(plug) -
STR RPTNC(jack) - STR, 5ft
AIR-CAB005LL-R
37-0766-01 OR Qty 4x LMR-400-DB RPTNC(plug)-R/A RPTNC(jack)-STR, 10ft
CAB-L400-10-R
37-100844-01 OR Qty 4x LMR-400-DB RPTNC(plug)-STR RPTNC(jack)-STR, 20ft
AIR-CAB020LL-R
72-2760-02 AND GPS port No extension cable required, 5-in-1 antenna comes with integrated active GPS antenna with 17ft cable. Cisco IR829 Integrated Services Router Hardware Installation Guide 1-20 Chapter 1 Product Overview Antennas Use Case Transportation Use Case 2:
7 x RF ports, with the IR829 deployed in a transportation application.
(Alternate Configuration, can be used in case the application calls for the WiFi antennas to be separate from the LTE antenna for example. a ceiling mount WLAN). This case describes a Tercia 3-in-1 transportation antenna (which covers MIMO cellular and GPS) together with qty 2 x 2-in-1 WiFi antennas. Note A CUSTOM CEILING MOUNT BRACKET IS REQUIRED FOR THE 2-in-1 antenna if installed in a ceiling mount configuration (NOT SUPPLIED BY CISCO) Extension Cable No extension cables are required if the IR829 unit is located within ~1.0ft of 3-in-1 antenna, and ~2.0ft of WiFi 2-in-1 antenna. If these conditions are not met, this deployment requires the following extension cables:
Cellular extension cables:
(2 ports) Qty 2X LMR-400-DB TNC(m)-R/A -
TNC(f), 5ft
4G-CAB-LMR400-5
37-100842-01 OR Qty 2X LMR-400-DB TNC(m)-R/A -
TNC(f), 10ft
4G-CAB-LMR400-10
37-100843-01 OR Qty 2X LMR-400-LLPL plenum / indoor only Antenna Tercia 3 element 3-in-1 transportation antenna, black radome color, 2x 4G cellular, 1xGPS
ANT-3-4G2G1-O
07-100263-01 Has the following integrated cables:
qty 2 x cellular, LMR-195, 2ft long, TNC(m) qty 1 x GPS, RG-174, 17ft long, SMA(m) AND QTY 2 of 2-in-1 antennas WiFi 2-in-1 2 element 2 in 1 transportation antenna, black radome color, 2x dual band WiFi
ANT-2-WLAN-D-O
07-100265-01 Has the following integrated cables:
qty 2 x WiFi, 3ft long, LMR-240 RPTNC (plug) A CUSTOM CEILING MOUNT BRACKET IS REQUIRED FOR THE 2-in-1 antenna if installed in a ceiling mount configuration (NOT SUPPLIED BY CISCO) TNC(m)-R/A - TNC(f), 20ft
4G-CAB-ULL-20 Note
37-1401-01 AND WiFi 2.4 GHz / 5GHz extension cables (4 ports, can mix and match lengths per installation requirements if needed) Qty 4x LMR-400-DB RPTNC(plug) -
STR RPTNC(jack) - STR, 5ft
AIR-CAB005LL-R
37-0766-01 OR Qty 4x LMR-400-DB RPTNC(plug)-R/A RPTNC(jack)-STR, 10ft
CAB-L400-10-R
37-100844-01 AND GPS port - No extension cable required, 3-in-1 antenna comes with integrated active GPS antenna with 17ft cable. Cisco IR829 Integrated Services Router Hardware Installation Guide 1-21 Chapter 1 Product Overview Power Supply Power Supply The Cisco IR829 comes with an external power connector.
Direct-wire 12/24VDC vehicle charging system input (9 32VDC).
4-pin locking power connector. SFP Modules The router Ethernet SFP modules provide connections to other devices. These field-replaceable transceiver modules provide the uplink interfaces. Local connectors (LCs) provide the fiber-optic connection. RJ-45 connectors allow copper connections. You can use any combination of the supported SFP modules listed in the table that follows. Table 1-8 Maximum Operating Temperature Type of SFP Module Rugged and Industrial SFPs 40 to 185F (40 to 85C) Model GLC-SX-MM-RGD with digital optical monitoring
(DOM) support GLC-LX-SM-RGD with digital optical monitoring
(DOM) support GLC-ZX-SM-RGD with digital optical monitoring
(DOM) support For minimum software requirements, refer to the Release Notes for your platform. For the most up-to-date list of supported SFP models for Cisco Industrial Ethernet switches, see http://www.cisco.com/en/US/docs/interfaces_modules/transceiver_modules/compatibility/matrix/OL_ 6981.html#wp138176 Cisco IR829 Integrated Services Router Hardware Installation Guide 1-22 C H A P T E R 2 Installing the Router This chapter describes the equipment and the procedures for successfully installing the Cisco IR829 and contains the following sections:
Equipment, Tools, and Connections, page 2-2
Installing the Router, page 2-3 Caution Do not place anything on top of the router that weighs more than 10 pounds (4.5 kilograms), and do not stack routers on a desktop. Excessive weight on top of the router could damage the chassis. Caution Do not install the router or power supplies next to a heat source of any kind, including heating vents. Warning Read the installation instructions before connecting the system to the power source. Statement 1004 Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030 Warning No user-serviceable parts inside. Do not open. Statement 1073 Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040 Warning Do not locate the antenna near overhead power lines or other electric light or power circuits, or where it can come into contact with such circuits. When installing the antenna, take extreme care not to come into contact with such circuits, because they may cause serious injury or death. For proper installation and grounding of the antenna, please refer to national and local codes (for example, U.S.:NFPA 70, National Electrical Code, Article 810, Canada: Canadian Electrical Code, Section 54). Statement 1052 Cisco IR829 Integrated Services Router Hardware Installation Guide 2-1 Equipment, Tools, and Connections Chapter 2 Installing the Router Warning This product is not intended to be directly connected to the Cable Distribution System. Additional regulatory compliance and legal requirements may apply for direct connection to the Cable Distribution System. This product may connect to the Cable Distribution System ONLY through a device that is approved for direct connection. Statement 1078 Equipment, Tools, and Connections This section describes the equipment, tools, and connections necessary for installing your Cisco IR829. It contains the following topics:
Items Shipped with your Router, page 2-2
Additional Items, page 2-2
Ethernet Devices, page 2-3 Items Shipped with your Router Unpack the box and verify that all items listed on the invoice were shipped with the Cisco IR829. The following items are shipped with your router:
Getting Started Guide Part Number 78-100611
Power Cable components
Grounding Lug
Ethernet Cable Part Number 75-1501-01 Additional Items The following items are not shipped with the router but are required for installation:
ESD-preventive cord and wrist strap.
Screws for mounting the router on a wall.
Two number-10 wood screws (round- or pan-head) with number-10 washers or two number-10 washer-head screws, for mounting on a wall stud. The screws must be long enough to penetrate at least 3/4 inch (20 mm) into the supporting wood or metal wall stud.
Two number-10 wall anchors with washers, for mounting the router on a hollow wall.
Wire crimper for chassis grounding.
Wire for connecting the chassis to an earth ground.
AWG 14 (2 mm2) or larger wire for NEC-compliant chassis grounding.
AWG 18 (1 mm2) or larger wire for EN/IEC 60950compliant chassis grounding.
Ethernet cables for connecting to the Fast Ethernet (FE) WAN and LAN ports.
Ratcheting torque flathead screwdriver that exerts up to 15 in-lb (1.69 N-m) of pressure.
A number-2 Phillips screwdriver. Cisco IR829 Integrated Services Router Hardware Installation Guide 2-2 Chapter 2 Installing the Router Ethernet Devices Installing the Router Identify the Ethernet devices that you will connect to the router: hub, servers, and workstations or PCs. Ensure that each device has a network interface card (NIC) for connecting to Ethernet ports. If you plan to configure the software using Cisco IOS commands through the console port, provide an ASCII terminal or a PC that is running terminal emulation software to connect to the console port. Installing the Router This section describes how to install the Cisco IR829. This router can be installed on a table top or other flat horizontal surface mounted on a wall or DIN rail. The recommended clearance when horizontally mounted is 1.5 inches on both sides for floor mount bracket clearance and 2 inches on top. Top clearance is not required but stacking heat-dissipating objects on top of the router is not allowed. I/O side clearance is needed as it is required to access the cable connections. Clearance is not required on the backside (opposite side from I/O face) unless DIN rail mounting is required. Clearance is required to attach and mount the DIN rail bracket. The same clearances apply when mounted vertically. This section also describes how to attach external antennas to the routers and contains the following topics:
Warnings, page 2-3
Accessing the SIM Cards, page 2-3
Installing Antennas, page 2-5
Mounting on a Wall, Table, or Other Flat Surface, page 2-5
Installing the Router Ground Connection, page 2-7 Warnings Warning This equipment needs to be grounded. Use a green and yellow 12 to 14 AWG ground wire to connect the host to earth ground during normal use. Statement 242 Accessing the SIM Cards This section describes how to install and/or replace a SIM card. Ensure that the router is not mounted to a wall, floor, or DIN rail. Caution Do not touch any part of the exposed PCB circuit area when the SIM cover is removed. Warning The covers are an integral part of the safety design of the product. Do not operate the unit without the covers installed. Statement 1077 Cisco IR829 Integrated Services Router Hardware Installation Guide 2-3 Installing the Router Chapter 2 Installing the Router Warning Hot surface. Statement 1079 Note High Temperature SIMs are required for 4G operations if the Ambient temperature is above 95F (35C) To access the SIM card in the Cisco IR829, follow these steps:
Step 1 Step 2 Step 3 Step 4 Place the router on its bottom and ensure that any installed antennas are carefully oriented. Remove the SIM access panel using two Phillips head screws. (See Figure 2-1.) Locate the SIM card you wish to install/replace. Details are shown in Figure 2-2. Remove the SIM card (if present) and install the new card(s). Figure 2-1 Accessing the SIM Cards Figure 2-2 Sim Card Detail 1. Reset Switch 2. Mini USB Port 3. Dual Sim Slots Step 5 Replace the panel and the screws. Cisco IR829 Integrated Services Router Hardware Installation Guide 2-4 Chapter 2 Installing the Router Installing Antennas Installing the Router Note Before you install the Cisco IR829 Integrated Services Router on a table, wall, or DIN rail, install the antennas on the front panel. It is difficult to install the antennas after the router is installed. There are four TNC connectors on the front side of the chassis. There are two TNC and one SMA connectors on the back side of the chassis. Two TNC connectors are used to connect to the 4G modem. The four TNC connectors at the back will be connected to the two 4G modems. The front two TNC connectors will be used for WiFi. Orient the antennas. For optimum wireless performance, the antennas should be perpendicular with respect to the floor. If the router is being mounted on a desk, orient the antennas straight up. To attach the radio antennas to your wireless router, follow these steps:
Step 1 Manually screw the antenna tight to the TNC connectors on the back of the router. Step 2 Orient the antennas. For optimum wireless performance, antennas should be generally perpendicular to each other. Mounting on a Wall, Table, or Other Flat Surface The Cisco IR829 has mounting holes on the bottom of the chassis for mounting the unit on a wall or other vertical surface. The attachment hardware is provided. Tip When choosing a location for wall-mounting the router, consider cable limitations and wall structure. Warning Read the wall-mounting instructions carefully before beginning installation. Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system. Statement 378 To mount the router on a wall, follow these steps:
Step 1 Locate the mounting holes on the router. There are 4 holes are shown circled in red in Figure 2-3. Cisco IR829 Integrated Services Router Hardware Installation Guide 2-5 Installing the Router Chapter 2 Installing the Router Figure 2-3 Cisco IR829 Mounting Holes Step 2 Install the router to a wall stud using two number-10 wood screws, round- or pan-head, with number-10 washers or two number-10 washer-head screws. The screws must be long enough to penetrate at least 1.0 inch (25.4 mm) into the supporting wood or metal wall stud. (See Figure 2-4.) Figure 2-4 Mounted to wall Note For hollow-wall mounting, each bracket requires two wall anchors with washers. Wall anchors and washers must be size number 10. Step 3 Route the cables so that they do not put a strain on the connectors or mounting hardware. Cables should be routed down relative to the router to prevent water from traveling on the cables. Cisco IR829 Integrated Services Router Hardware Installation Guide 2-6 Chapter 2 Installing the Router Installing the Router Installing the Router Ground Connection The router must be connected to a reliable earth ground. Install the ground wire in accordance with local electrical safety standards.
For NEC-compliant grounding, use size 14 AWG (2 mm2) or larger copper wire and a ring terminal with an inner diameter of 1/4 in. (5 to 7 mm).
For EN/IEC 60950-compliant grounding, use size 18 AWG (1 mm2) or larger copper wire. Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024 Warning This equipment needs to be grounded. Use a green and yellow 12 to 14 AWG ground wire to connect the host to earth ground during normal use. Statement 242 To install the ground connection, follow these steps:
Step 1 Step 2 Step 3 Step 4 Locate the grounding lug attached to the back of the Cisco IR829. It will be attached underneath two screws. Remove the screws holding it to the router and set it aside for reuse. Strip one end of the ground wire to the length required for the terminal. Crimp the ground wire to the grounding lug using the wire crimper. Attach the grounding lug to the chassis using the screws set aside in step 1. Tighten the screw to a torque of 8 to 10 inch-pound (0.9 to 1.1 newton meter). (See Figure 2-5.) Figure 2-5 Chassis Ground Connection Points Step 5 Step 6 Connect the other end of the ground wire to a known reliable earth ground point at your site. If you are using this router in a vehicle, attach the ring terminal to the chassis using one of the screws provided and the green or green and yellow striped wire. Connect the other end of the wire to the vehicle ground. After you install and properly ground the router, you can connect the power wiring, the LAN cables, and the cables for administrative access as required for your installation. Cisco IR829 Integrated Services Router Hardware Installation Guide 2-7 Installing the Router Chapter 2 Installing the Router Cisco IR829 Integrated Services Router Hardware Installation Guide 2-8 C H A P T E R 3 Connecting the Router This chapter describes how to connect Cisco IR829 Integrated Services Router (ISRs) to Ethernet devices and a network. The chapter contains the following sections:
Preparing to Connect the Router, page 3-1
Connecting a PC, Server, or Workstation, page 3-2
Connecting a Terminal or PC to the Console Port, page 3-3
Connecting to DC Power, page 3-3
Verifying Connections, page 3-6 Note For compliance and safety information, see the Regulatory Compliance and Safety Information Roadmap that ships with the router and Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers. Preparing to Connect the Router Before you connect the router to the devices, install the router according to the instructions in Chapter 2, Installing the Router. Preventing Damage to the Router To prevent damage to your router, follow these guidelines when connecting devices to your router:
Turn off power to the devices and to the router until all connections are completed. Caution Do not turn on the devices until after you have completed all connections to the router.
If you must supply your own cable, see the Technical Specifications section on page 6-1 for cabling specifications. If this appendix does not provide specifications for a particular cable, we strongly recommend ordering the cable from Cisco. Cisco IR829 Integrated Services Router Hardware Installation Guide 3-1 Chapter 3 Connecting the Router Preparing to Connect the Router Connecting a PC, Server, or Workstation To connect a PC (or other Ethernet devices) to an Ethernet switch port, follow these steps:
Step 1 Connect one end of the Ethernet cable to an Ethernet switch port on the router. In this example a PC is being connected to GE LAN Port 2. See Figure 3-1. Figure 3-1 Connecting a Server, PC, or Workstation 1 2 Ethernet cable Ethernet switch port on the router 3 RJ-45 port on the PC, Server, or Workstation Step 2 Connect the other end of the cable to the RJ-45 port on the network interface card (NIC) that is installed in the PC, server, or workstation. Cisco IR829 Integrated Services Router Hardware Installation Guide 3-2 Chapter 3 Connecting the Router Connecting a Terminal or PC to the Console Port Step 3
(Optional) Connect additional servers, PCs, or workstations to the other Ethernet switch ports. Connecting a Terminal or PC to the Console Port Connect a terminal or PC to the Console port either to configure the software by using the CLI or to troubleshoot problems with the router. To connect a terminal or PC to the console port on the router and access the CLI, follow these steps:
Step 1 Connect the mini-USB side of a cable to the USB Console port on the router. Figure 3-2 shows the mini-USB location (1) for the Console port on the router. Step 2 Step 3 Step 4 Figure 3-2 Connecting a Terminal or PC to the Console Port Connect the opposite end of the mini-USB cable to the USB port on your laptop or PC. To communicate with the router, wait for your laptop or PC to discover the new device. If your laptop or PC warns you that you do not have the proper drivers to communicate with the router, you can obtain them from your computers manufacturer, or go here:
https://www.silabs.com/products/mcu/Pages/USBtoUARTBridgeVCPDrivers.aspx Connecting to DC Power Warning This product relies on the buildings installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than 36 VDC, 5A Statement 1005 Warning This product requires short-circuit (overcurrent) protection, to be provided as part of the building installation. Install only in accordance with national and local wiring regulations. Statement 1045 Cisco IR829 Integrated Services Router Hardware Installation Guide 3-3 Chapter 3 Connecting the Router Plugs and Pin-Outs Connecting to DC Power The IR829 ships with a DC power accessory kit that contains a 4-pin locking connector and pins to use for the power connections. Four contacts are supplied, but only three are used. One is a spare. The power entry receptacle is on the IR829. The pin-outs are shown in Figure 3. Figure 3 Power Connector Pin-outs Figure 4 Pin Number 1 2 3 4 Power connector Descriptions Name DC In -
Ignition DC In +
N/A Description DC Power Return (GND-) Ignition Input (IGN) DC Power In (BAT+) N/A Color Black Blue Red N/A Constructing a Power cable Special care should be taken when making the connections for DC power. It is easy to make a mistake when crimping connections, and there is a very good tutorial available at Molex:
http://www.molex.com/tnotes/crimp.html The specifications for the wiring are as follows:
16 AWG (1.02-to-1.29mm)
UL1015 Rated
Wires will be wound at 1 twist per inch The example in Figure 3-5 shows a cable constructed with a ferrite for a different certification. You can build your cable without the ferrite eliminating items 2 and 3 in the diagram. Cisco IR829 Integrated Services Router Hardware Installation Guide 3-4 Chapter 3 Connecting the Router Connecting to DC Power Figure 3-5 Power cable 4 3 2 1 Details listed in the power cable example are:
4-pin locking connector 2 loops of DC power and power return wires only. Other wires that may be used should run outside the Ferrite. Ferrite Bead Wires wound at 1 twist per inch 1 2 3 4 0 9 7 9 4 3 Note Note Ferrite bead and the loops of wire are not needed at this time. Ferrite bead and the loops of wire are not needed at this time. Wiring the DC Power To connect the DC power on your Cisco IR829, follow these steps:
Step 1 Identify the DC power source and measure 4 strands of copper wire 16 AWG (1.29mm) long enough to connect to the DC power source. Note The maximum length of the cable before twisting is 15 feet (4.6 meters). Step 2 Using an 16-gauge wire-stripping tool, strip each of the wires coming from each DC-input power source to 0.25 inch (6.3 mm) 0.02 inch (0.5 mm). Do not strip more than 0.27 inch (6.8 mm) of insulation from the wire. Stripping more than the recommended amount of wire can leave exposed wire from the power connector after installation. Cisco IR829 Integrated Services Router Hardware Installation Guide 4 8 0 3 3 3 3-5 Chapter 3 Connecting the Router Verifying Connections Step 3 Using the pins included in the kit, crimp each pin onto a wire. Step 4 Step 5 Insert the pins into the power connector, referring to previous figures for guidance. Plug the connector into the power entry receptacle. Verifying Connections To verify that all devices are properly connected to the router, first turn on all the connected devices, then check the LEDs. To verify router operation, refer to Table 3-1. For full LED description, see Chapter 1, LEDs Table 3-1 Verifying the Router Operation Power and Link PWR GE0 WAN Ethernet LAN Switch Ports LEDs to Check Green steady On Green (blinking) Yellow Steady On Flashing Off Single LED per port Normal Patterns Normal operation Boot up phase or in ROM Monitor mode System shutdown due to under or over voltage conditions Link is up Transmitting and Receiving data No network activity. Off No link Green Steady on Link is up Green Blink Transmitting and Receiving data Yellow POE Fault, implies no link Cisco IR829 Integrated Services Router Hardware Installation Guide 3-6 Chapter 3 Connecting the Router Verifying Connections Table 3-1 Verifying the Router Operation (continued) Power and Link Sim cards LEDs to Check SIM0/SIM1 Cellular Modems CELLULAR0/
CELLULAR1 Normal Patterns Off No USIM Green USIM installed and active Off Module not powered on On Module is powered on and connected but not transmitting or receiving Slow Blink Module is powered on and searching for connection Fast Blink Module is transmitting or receiving. Cisco IR829 Integrated Services Router Hardware Installation Guide 3-7 C H A P T E R 4 Initial Configuration This chapter provides instructions for initial configuration of the Cisco IR829 Integrated Services Routers (ISRs). To create the initial configuration, the setup command facility prompts you for basic information about your router and network. This chapter contains the following sections:
Setup Command Facility, page 4-1
Verifying the Initial Configuration, page 4-4
Where To Go From Here, page 4-4 Setup Command Facility The setup command facility guides you through the configuration process by prompting you for the specific information that is needed to configure your system. Use the setup command facility to configure a hostname for the router, to set passwords, and to configure an interface for communication with the management network. To use the setup command facility, you must set up a console connection with the router and enter the privileged EXEC mode. To configure the initial router settings by using the setup command facility, follow these steps:
Step 1 Step 2 Set up a console connection to your router, and enter privileged EXEC mode. In privileged EXEC mode, at the prompt, enter setup. yourname# setup The following message is displayed:
--- System Configuration Dialog ---
Would you like to enter the initial configuration dialog? [yes/no]:
You are now in the setup command facility. The prompts in the setup command facility vary, depending on your router model, on the installed interface modules, and on the software image. The following steps and the user entries (in bold) are shown as examples only. Cisco IR829 Integrated Services Router Hardware Installation Guide 4-1 Setup Command Facility Chapter 4 Initial Configuration Note If you make a mistake while using the setup command facility, you can exit and run the setup command facility again. Press Ctrl-C and enter the setup command at the privileged EXEC mode prompt (Router#). To proceed using the setup command facility, enter yes. Would you like to enter the initial configuration dialog? yes Step 3 When the following messages appear, enter yes to enter basic management setup. At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'. Basic management setup configures only enough connectivity for management of the system, extended setup will ask you to configure each interface on the system Would you like to enter basic management setup? [yes/no]: yes Step 4 Enter a hostname for the router (this example uses Router). Configuring global parameters:
Enter host name [Router]: Router Step 5 Enter an enable secret password. This password is encrypted (more secure) and cannot be seen when viewing the configuration. The enable secret is a password used to protect access to privileged EXEC and configuration modes. This password, after entered, becomes encrypted in the configuration. Enter enable secret: xxxxxx Step 6 Enter an enable password that is different from the enable secret password. This password is not encrypted (less secure) and can be seen when viewing the configuration. The enable password is used when you do not specify an enable secret password, with some older software versions, and some boot images. Enter enable password: xxxxxx Step 7 Enter the virtual terminal password, which prevents unauthenticated access to the router through ports other than the console port. The virtual terminal password is used to protect access to the router over a network interface. Enter virtual terminal password: xxxxxx Step 8 Respond to the following prompts as appropriate for your network:
Configure SNMP Network Management? [yes]:
Community string [public]:
A summary of the available interfaces is displayed. The following is an example summary and may not reflect your configuration:
Current interface summary Any interface listed with OK? value "NO" does not have a valid configuration Interface IP-Address OK? Method Status Protocol GigabitEthernet0 20.1.0.165 YES DHCP up up GigabitEthernet1 unassigned NO unset up up Cisco IR829 Integrated Services Router 4-2 Chapter 4 Initial Configuration Setup Command Facility Async0 unassigned YES unset up down Async1 unassigned YES unset up down GigabitEthernet2 unassigned NO unset up up Cellular0 unassigned NO unset down down Cellular1 unassigned NO unset down down Step 9 Choose one of the available interfaces for connecting the router to the management network. Enter interface name used to connect to the management network from the above interface summary: GigabitEthernet0 Step 10 Respond to the following prompts as appropriate for your network:
Configuring interface GigabitEthernet0:
Configure IP on this interface? [yes]: yes Use the 100 Base-TX (RJ-45) connector? [yes]: yes Operate in full-duplex mode? [no]: yes Configure IP on this interface? [yes]: yes IP address for this interface: 172.1.2.3 Subnet mask for this interface [255.255.0.0] : 255.255.0.0 Class B network is 172.1.0.0, 26 subnet bits; mask is /16 The configuration is displayed:
The following configuration command script was created:
hostname Router enable secret 5 $1$D5P6$PYx41/lQIASK.HcSbfO5q1 enable password xxxxxx line vty 0 4 password xxxxxx snmp-server community public
!
no ip routing
!
interface GigabitEthernet0 no shutdown speed 100 duplex auto ip address 172.16.2.3 255.255.0.0
!
Step 11 Respond to the following prompts. Enter 2 to save the initial configuration.
[0] Go to the IOS command prompt without saving this config.
[1] Return back to the setup without saving this config.
[2] Save this configuration to nvram and exit. Enter your selection [2]: 2 Building configuration... Use the enabled mode 'configure' command to modify this configuration. Press RETURN to get started! RETURN The user prompt is displayed. Router>
Step 12 Verify the initial configuration. See the Verifying the Initial Configuration section on page 4-4 for verification procedures. Cisco IR829 Integrated Services Router Hardware Installation Guide 4-3 Verifying the Initial Configuration Chapter 4 Initial Configuration After the initial configuration file is created, you can use the Cisco IOS CLI to perform additional configuration. Verifying the Initial Configuration To verify that the new interfaces are operating correctly, perform the following tests:
To verify that the interfaces and line protocol are in the correct stateup or downenter the show interfaces command.
To display a summary status of the interfaces configured for IP, enter the show ip interface brief command.
To verify that you configured the correct hostname and password, enter the show configuration command. After you complete and verify the initial configuration, you can configure your Cisco router for specific functions. Where To Go From Here There are a wide variety of configuration options available on the Cisco IR829. The rest of this chapter will discuss different pieces of documentation to refer to, as well as point out the differences between this device and the rest of the 800 series routers. 800 Series Documentation The home for all of the 800 series router documentation is here:
http://www.cisco.com/c/en/us/support/routers/800-series-routers/tsd-products-support-series-home.ht ml Most of the Cisco IR829 configuration tasks are available in the Cisco 800 Series Integrated Services Routers Software Configuration Guide:
http://www.cisco.com/c/en/us/td/docs/routers/access/800/software/configuration/guide/SCG800Guide. htm Some common tasks between the Cisco 800 series and the Cisco IR829 are listed here:
Configuring Wireless Devices http://www.cisco.com/c/en/us/td/docs/routers/access/800/software/configuration/guide/SCG800Guide/
SCG800_Guide_BookMap_chapter_01001.html Cisco 4G LTE Software Installation Guide http://www.cisco.com/c/en/us/td/docs/routers/access/interfaces/software/feature/guide/EHWIC-4G-LT ESW.html Cisco IR829 Integrated Services Router 4-4 Chapter 4 Initial Configuration Cisco IR829 Differences Cisco IR829 Differences This section will discuss some of the ways that the Cisco IR829 differs from the rest of the 800 series. LEDs The Cisco IR829 has LEDs that are discussed in previous chapters in this guide. There is also a command that will show you the status of the LEDs if you are not near the device. Use the show platform led command with options to view the different output. IR800#show platform led LED STATUS:
==================================================
GE PORTS : GE0 GE1 GE2 GE3 GE4 LINK LED : GREEN GREEN GREEN GREEN OFF
==================================================
PoE LED : GREEN Cellular PORTS: Cellular0 RSSI LED 1 : Green RSSI LED 2 : Green RSSI LED 3 : Off GPS LED : Slow Blinking SIM0 LED : Green SIM1 LED : Off
==================================================
VPN LED : OFF System LED: amber, blinking IR800#show platform led summary Ports LINK/ENABLE
-------+---------------
GE0 GREEN GE1 GREEN GE2 GREEN GE3 GREEN GE4 OFF
-------+---------------
PoE LED : GREEN RSSI 1 RSSI 2 RSSI 3 GPS
-----+------------+------------+------------+-------------
Ce0 Green Green Off Slow Blink
-----+------------+------------+------------+-------------
Cellular SIM0 SIM1
--------+-------+-------
Ce0 Green Off
--------+-------+-------
VPN LED : OFF System LED: amber, blinking Cisco IR829 Integrated Services Router Hardware Installation Guide 4-5 Cisco IR829 Differences Chapter 4 Initial Configuration IR800#show platform led system System LED: amber, blinking Summary of the LED status providers:
Client Type Status
------------------------------ -------- --------
GigabitEthernet5 critical OK Note There may be a lag time between the LED indication on the router and what the show led commands return. Software Bundle Installation The Cisco IR829 ships with the latest software available with the configuration that was ordered. There should be no reason to have to upgrade unless a failure occurs or you have been instructed to reload all software. Should the need arise, the following steps will assist in performing a bundle installation. Overview:
1. Download the bundle to flash memory from a TFTP server. 2. Install the bundle from the Command Line Interface 3. Save the configuration and reload the router to use the new image. 4. Download the 4G firmware upgrade. Example:
Step 1 Copy the bundle from a TFTP server to your router. IR800#copy tftp flash Address or name of remote host [223.255.254.254]? your ip address here Source filename [path to file/ir800-universalk9-bundle.SSA.156-0.3.T]?
Destination filename [ir800-universalk9-bundle.SSA.156-0.3.T]?
Accessing tftp://223.255.254.254/tachen/ir800-universalk9-bundle.SSA.156-0.3.T... Loading tachen/ir800-universalk9-bundle.SSA.156-0.3.T from 223.255.254.254 (via Vlan1): !
*Jun 25 18:28:45.685: %ARP-4-NULL_SRC_MAC: NULL MAC address from 99.99.0.1 on wl0!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!
[OK - 143536651 bytes]
143536651 bytes copied in 774.390 secs (185354 bytes/sec) Step 2 The bundle download is complete, and now needs to be installed. Perform the bundle install flash:
< bundle iOS image name> command. IR800#bundle install flash:ir800-universalk9-bundle.SSA.156-0.3.T Installing bundle image:
/ir800-universalk9-bundle.SSA.156-0.3.T................................................... ....................................... updating Hypervisor image... Sending file modes: C0444 23753557 ir800-hv.srp.SPA.0.28 SRP md5 verification passed!
Cisco IR829 Integrated Services Router 4-6 Chapter 4 Initial Configuration Cisco IR829 Differences updating IOS image... Sending file modes: C0644 61505652 ir800-universalk9-mz.SSA.156-0.3.T IOS md5 verification passed!
Done!
IR800#
*Jun 25 18:51:16.975: %SYS-5-CONFIG_I: Configured from console by bundle install command
*Jun 25 18:51:16.975: %IR800_INSTALL-6-SUCCESS_BUNDLE_INSTALL: Successfully installed bundle image. Step 3 Save the configuration and reload the router. IR800#reload Do you want to reload the internal AP ? [yes/no]: yes System configuration has been modified. Save? [yes/no]: yes Building configuration...
[OK]
Proceed with reload? [confirm]press return
*Jun 25 19:03:13.685: %SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload Command. Step 4 Download the 4G firmware or AP image. Instructions for uploading firmware are located here:
http://www.cisco.com/c/en/us/td/docs/routers/access/interfaces/software/feature/guide/EHWIC-4G-LT ESW.html Search for Upgrading the Modem Firmware. Cisco IR829 Integrated Services Router Hardware Installation Guide 4-7 Cisco IR829 Differences Chapter 4 Initial Configuration Cisco IR829 Integrated Services Router 4-8 C H A P T E R 5 Guest Operating System (Guest OS) Installation and Configuration This chapter details Guest Operating System (Guest OS) installation for the Cisco IR829. This chapter contains the following sections:
Guest Operating System Overview, page 5-1
Prerequisites, page 5-2
Guidelines and Limitations, page 5-2
Installation and Upgrade, page 5-2
Configuring Cisco IOS, page 5-3
Configuring Guest OS, page 5-6
Configuring NAT, page 5-8
Troubleshooting, page 5-9
Related Documentation, page 5-9 Guest Operating System Overview The IR829 supports a Hypervisor architecture to support multiple user-specified operating systems within independent Virtual Machines (VMs). Specific functions include Serial Relay and Network Address Translation (NAT). Cisco IOS interacts closely with the platform and underlying Hypervisor. Cisco Guest OS allows you to run the Linux operating system (if within the memory, disk, and CPU budget) next to Cisco IOS on the Hypervisor. Cisco Guest OS does not require signing, allowing maximum deployment latitude; however you must ensure the integrity and proper behavior for any Guest OS that you install. When you install the IR829 software bundle (image) on the router, the image automatically installs the supported Guest OS (Cisco IOS and Linux OS) instance(s). You can use the Linux Guest OS running on a VM on the IR829 to run utility applications. The following example shows connectivity of Guest OS and Cisco IOS. A virtual interface (see Configuring Guest OS Interface on Cisco IOS) managed by Cisco IOS provides network connectivity to Guest OS. Cisco IOS forwards traffic from Guest OS through regular IP forwarding mechanisms. Cisco IR829 Integrated Services Router Hardware Installation Guide 5-1 Prerequisites Chapter 5 Guest Operating System (Guest OS) Installation and Configuration Figure 5-1 Connectivity Between Cisco IOS and Guest OS In this example, number 1 is the interface being used on the router and number 2 is the interface on the Linux OS. For the Cisco IR829, 1 is Gigabit Ethernet 5 and 2 is Eth 0. Prerequisites
Router must be running Cisco IOS. Guidelines and Limitations
The bundled Guest OS is based on Linux kernel version 3.8.11.
You must configure Cisco IOS to provide Guest OS Connectivity. Default Settings The bundled Linux Guest OS:
uses DHCP to acquire the IP address.
does not have a default root password. Installation and Upgrade By default, IR829s ship with a software bundle that includes the latest versions of all of the required images such as Cisco IOS, Guest OS, and Hypervisor. Use the following procedure to upgrade your router to the latest software bundle. It can take several minutes for the router to upgrade and install all of the images (Hypervisor, Cisco IOS, and Guest OS). DETAILED STEPS Step 1 Copy the bundle image to the IR829 IOS flash partition using scp or sftp. Example bundle name: ir800-universalk9-bundle.SPA.<VERSION>
Step 2 Enter the following commands at the IR829 prompt:
Cisco IR829 Integrated Services Router 5-2 Chapter 5 Guest Operating System (Guest OS) Installation and Configuration Configuring Cisco IOS Command bundle install flash: <bundle name>.CG copy running config-config startup-config reload Purpose Installs the specified bundle. Saves the current running configuration. Reloads the router. Configuring Cisco IOS This section describes how to configure the Cisco IOS VM to provide network connectivity to the Guest OS VM. Guest OS connects to the network through a virtual Network Interface Card (VNIC) provided by the Hypervisor. Network attributes on the interface are statically configured or configured for DHCP to dynamically obtain IP addresses. Guest OS network connectivity is only through Cisco IOS, using the virtual network interface provided by the Hypervisor. Network attributes such as IP address, can be configured statistically or dynamically, and are obtained from Cisco IOS using DHCP requests. The bundled Linux Guest OS is configured to use DHCP. This section outlines the task to configure a Cisco IOS DHCP pool to provision the Linux Guest OS with an IP address, and an external Ethernet interface in Cisco IOS to allow the Guest OS network connectivity. This section includes the following topics:
Configuring the IR829 Ethernet Interface, page 5-3
Configuring Guest OS Interface on Cisco IOS, page 5-5
Enabling Guest OS Console, page 5-6 Configuring the IR829 Ethernet Interface You must enable one of the external Ethernet interfaces on the IR829 to provide network connectivity. For details on interface configuration refer to the Cisco 800 Series Integrated Services Routers Software Configuration Guide:
http://www.cisco.com/c/en/us/td/docs/routers/access/800/software/configuration/guide/SCG800Guide. html IPv6 Gigabit Ethernet On Guest OS, IPv6 is enabled by default. The following example configuration uses IPv6 on Guest OS, where Guest OS is automatically assigned an IPv6 address by enabling prefix delegation on the Cisco IOS interface GigabitEthernet 5. The following example configures G 0 for external connectivity:
interface GigabitEthernet 0 no switchport ipv6 address autoconfig default ipv6 enable Cisco IR829 Integrated Services Router Hardware Installation Guide 5-3 Configuring Cisco IOS Chapter 5 Guest Operating System (Guest OS) Installation and Configuration ipv6 dhcp client pd prefix-from-provider end The following example configures G5 to allow the Guest OS network connectivity:
interface GigabitEthernet 5 duplex auto speed auto ipv6 address prefix-from-provider ::2:0:0:0:1/64 ipv6 enable end Enabling IPv4 Gigabit Ethernet To enable an external Gigabit Ethernet IPv4 interface on the IR829 to provide network connectivity, enter the following commands:
Command config terminal interface gig 0 ip address 9.1.1.5 255.255.255.0 no shutdown Purpose Enters global configuration mode. Configures an IPv4 address on Gigabit Ethernet interface 0, and enters interface configuration mode. Sets the IP address and subnet mask for Gigabit Ethernet interface 0. Enables the Gigabit Ethernet interface. Configuring DHCP Pool To configure a local DHCP pool, enter the following commands, one per line:
Note The subnet used for the local DHCP pool must be reachable externally. If you cannot allocate the whole subnet to Guest OS, use a NAT-based configuration. See Configuring NAT. Command config terminal ip dhcp pool gospool network 9.1.2.0 255.255.255.0 default-router 9.1.2.1 domain-name utility.com dns-server 9.1.1.1 lease 5 Purpose Enters global configuration mode. Names the local DHCP pool. Sets the network address. Sets the router address. Sets the subnet address. Sets the DNS server address. Sets the duration of the IP address lease to five days. Cisco IR829 Integrated Services Router 5-4 Chapter 5 Guest Operating System (Guest OS) Installation and Configuration Configuring Cisco IOS Configuring Guest OS Interface on Cisco IOS The Guest OS Ethernet port (eth0) connects to GigabitEthernet 5 on Cisco IOS. To configure the GigabitEthernet 5 interface with the default gateway address of the DHCP pool, enter the following commands:
Note IPv6 must always be enabled on GigabitEthernet 5. Command interface GigabitEthernet 5 Purpose Set the internal virtual interface that connects to the Linux Guest OS. Enables IPv6. ipv6 enable ipv6 address 2001:DB8:FFFF:0000:0000:0000:0001 Sets the IPv6 address. ipv4 enable ipv4 address 9.1.2.1 255.255.255.0 no shutdown Enables IPv4. Sets the IPv4 address. Note There exists a condition where the IR829 could display slow performance if the guest OS is consuming too many CPU resources. By default, Guest OS gets 50% of one of the cores of the CPU. The following command allows you to change the percentage of CPU allocation to VDS out of 100. The rest will go to Guest OS. In the situation where you don't use the Guest OS, the CPU can be allocated 90% to VDS. For Example:
IR800>en IR800#config t Enter configuration commands, one per line. End with CNTL/Z. IR800(config)#iox hypervisor ?
sched-policy percentage of CPU ticks to VDS IR800(config)#iox hypervisor sched-policy ?
10 VDS 10% Guest OS 90%
20 VDS 20% Guest OS 80%
30 VDS 30% Guest OS 70%
40 VDS 40% Guest OS 60%
50 VDS 50% Guest OS 50%
60 VDS 60% Guest OS 40%
70 VDS 70% Guest OS 30%
80 VDS 80% Guest OS 20%
90 VDS 90% Guest OS 10%
IR800(config)#iox hypervisor sched-policy 90 Cisco IR829 Integrated Services Router Hardware Installation Guide 5-5 Configuring Guest OS Chapter 5 Guest Operating System (Guest OS) Installation and Configuration Enabling Guest OS Console For heightened security, Guest OS console is disabled by default. To enable Guest OS console, enter the following commands:
Command config terminal line 1/4 transport input all Purpose Enters global configuration mode. Specifies line 1/4 for configuration and enters line configuration collection mode. Defines which protocols to use to connect to a specific line of the router. Configuring Guest OS This section describes how to set the root password for Guest OS and enable SSH access. By default, SSH is disabled in Guest OS, this section describes the steps to reverse-Telnet into Guest OS, and enable SSH access. Starting Guest OS By default, Guest OS starts after installation. To manually start the Guest OS, enter the following commands:
Command show iox host list detail guest-os 1 start Purpose Displays OS: RUNNING if Guest OS is already running. If it is, go to Accessing Guest OS Console. Starts Guest OS. During start up, Guest OS sends a DHCP request and is assigned an IP address from the local DHCP pool. Guest OS is then configured with a hostname and sync time from IOS. Note It can take a few minutes for the Guest OS to start. Accessing Guest OS Console The Guest OS console is accessible at port 2070 on any Cisco IOS interface. Use the following commands to access the Linux Guest OS console from Cisco IOS. Note You must first enable the Guest OS console as described in Enabling Guest OS Console. Cisco IR829 Integrated Services Router 5-6 Chapter 5 Guest Operating System (Guest OS) Installation and Configuration Configuring Guest OS Command telnet 9.1.2.1 2070 Purpose Accesses the Guest OS console. This uses the IP address of the Gigabit Ethernet 5 port. The following is the example result:
EXAMPLE Poky 9.0 (Yocto Project 1.4 Reference Distro) 1.4 qemux86 ttyS0 qemux86 login: root root@qemux86:~#
Setting the Root Password Guest OS does not have a default root password. To set a root password, at the GOS prompt enter the following command. Note You must set a root password before turning on SSH access. Command
[GOS] # passwd Purpose Runs the following UNIX password script. Enter your desired password at the prompt. EXAMPLE Changing password for user root. New UNIX password:
Retype new UNIX password:
passwd: all authentication tokens updated successfully.
[GOS]#
An alternate method for changing the root password is shown in the following example:
IR800#iox host exec "resetpw cisco" IR800-GOS-1 Password reset successfully. Enabling Remote SSH Access By default, SSH access is disabled to prevent unauthorized access to Guest OS. To enable SSH server on the guest OS:
Step 1 Launch the vi editor to edit the sshd_config file:
vi /etc/ssh/sshd_config Step 2 Set the PermitRootLogin and PasswordAuthentication parameters to yes. Cisco IR829 Integrated Services Router Hardware Installation Guide 5-7 Configuring NAT Chapter 5 Guest Operating System (Guest OS) Installation and Configuration Note Ensure that the PermitEmptyPasswords parameter is set to no. PermitRootLogin yes PasswordAuthentication yes PermitEmptyPasswords no Step 3 Restart SSHD:
[GOS]# /etc/init.d/sshd stop Stopping sshd: [ OK ]
[GOS]# /etc/init.d/sshd start Starting sshd: [ OK ]
[GOS]#
Step 4 From the IOS command line, enter the following:
IR800#iox host exec enablessh IR800-GOS-1 ssh enabled successfully. You now have remote SSH access to Guest OS. Configuring NAT The following example configuration uses NAT for Guest OS network connectivity, where:
9.1.1.0 is the externally reachable subnet.
9.1.1.131 is the external IP address made available for Guest OS access.
192.168.1.0 is the private subnet created for Guest OS to Cisco IOS connectivity. This is not directly reachable outside the IR829.
The IP address acquired by Guest OS through IOS local DHCP pool is 192.168.1.2. This address can be obtained using show iox host list details command from IOS. ip dhcp pool gospool network 192.168.1.0 255.255.255.0 default-router 192.168.1.1 domain-name utility.com dns-server 9.1.1.1 lease 5 interface gig 5 ip nat inside ip address 192.168.1.1 255.255.255.0 ipv6 enable no shutdown interface gig 0 ip nat outside ip address 9.1.1.5 255.255.255.0 no shutdown ip nat inside source static 192.168.1.2 9.1.1.131
! End of configuration IR800#sh ip nat trans Cisco IR829 Integrated Services Router 5-8 Chapter 5 Guest Operating System (Guest OS) Installation and Configuration Troubleshooting Pro Inside global tcp 9.1.1.131:22 tcp 9.1.1.131:60100
--- 9.1.1.131 Inside local 192.168.1.2:22 192.168.1.2:60100 192.168.1.2 Outside local 9.1.1.3:53649 9.1.1.3:22
---
Outside global 9.1.1.3:53649 9.1.1.3:22
---
Troubleshooting To determine common causes of configuration failure, enter the following commands:
Command ifconfig eth0 Purpose Checks if Guest OS is assigned an IP address. The following is example output:
eth0
[GOS]#
netstat -r Link encap:Ethernet HWaddr 02:00:03:f1:cd:05 inet addr:9.1.2.2 Bcast:0.0.0.0 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2 errors:0 dropped:0 overruns:0 frame:0 TX packets:5 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:684 (684.0 B) TX bytes:894 (894.0 B) Displays the Guest OS route table. The following is example output:
Kernel IP routing table Destination default 9.1.2.0
[GOS]#
show ip arp Gateway 9.1.2.1
*
Genmask 0.0.0.0 255.255.255.0 Flags UG U MSS 0 0 Window 0 0 irtt 0 0 Iface eth0 eth0 Verifies that Cisco IOS learned Guest OS ARP mapping.The following is example output:
Protocol Internet Internet Internet IR800#
Address 9.1.1.1 9.1.2.1 9.1.2.2 Age (min)
-
-
112 Hardware Addr 0022.bdef.c562 0022.bdef.c569 0022.bdef.c56d Type ARPA ARPA ARPA Interface GigabitEthernet0 GigabitEthernet5 GigabitEthernet5 Checking Connectivity Use standard Linux tools (for example, ping and traceroute) to check Guest OS connectivity. Related Documentation Find Cisco 1000 Series Connected Grid Routers product documentation at:
www.cisco.com/go/cgr1000-docs. Find Connected Grid Modules for Cisco 1000 Series Connected Grid Routers documentation at:
www.cisco.com/go/cg-modules Cisco IR829 Integrated Services Router Hardware Installation Guide 5-9 Related Documentation Chapter 5 Guest Operating System (Guest OS) Installation and Configuration For information on supporting systems referenced in this guide, see the following documentation on Cisco.com:
Cisco ASR 1000 Series Aggregation Services Routers Configuration Guide Cisco 3945 Series Integrated Services Router Cisco 2000 Series Connected Grid Routers Installation and Configuration Guide for Cisco Services Ready Engine Virtualization 1.1 Cisco IOS IP Application Services Command Reference Cisco IR829 Integrated Services Router 5-10 C H A P T E R 6 Technical Specifications This appendix provides router, port, cabling specifications, and power adapters for the Cisco IR829 Integrated Services Router (ISRs). Note For compliance and safety information, see the Regulatory Compliance and Safety Information Roadmap that was shipped with the router and Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers. Router Specifications Table 6-1 lists the operational limits of the Cisco IR829. Operating the router outside of the limits specified is not supported. Table 6-1 Cisco IR829 Specifications Description Physical Characteristics Dimensions (H x W x D) Weight Maximum Power Consumption Environmental Operating Ranges Operating Temperature and Altitude Humidity Environmental Tests Ingress Protection Rating Humidity Design Specification
(height x width x depth x) are 7.70 x 11 x 1.73 in. (19.6 x 27.9 x 4.39 cm). 5 lb (1.0 kg) 70 Watts with PoE 40 to 140F (40 to 60C). -500 to 5,000 feet. Derate max operating temperature 1.5C per 1000 feet. 10,000 ft maximum 10% 95% non-condensing IP 40 per IEC 60529 for Vertical Falling Water, Pollution Degree 3 Non-condensing Relative Humidity: 5% to 95%
Cisco IR829 Integrated Services Router Hardware Installation Guide 6-1 Chapter 6 Technical Specifications Table 6-1 Cisco IR829 Specifications (continued) Description Military Standard Design Specification MIL-STD-810G Method 514.6: Procedure 1 Category 4, Secured Cargo - Common MIL-STD-810G Method 514.6: Procedure 1 Category 20, Ground Vehicles Vibration and Shock (Railway Vehicles) Heavy-Duty Vehicle Applications Certifications Standard Safety Certifications Transportation/Storage Conditions Temperature Humidity Altitude MIL-STD-810G Method 516.6. Procedure 1, Functional Shock MIL-STD-810G Method 516.6. Procedure 5, Crash Hazard MIL-STD-810G Method 516.6. Procedure 6, Bench Handling EN61373 Functional Random Vibe - Category 1, Class B EN61373 Simulated Non-op Long-life Vibe - Category 1, Class B EN61373 Non-op Shock, Class B SAE J1455 Operating Random Vibe, Cab Mounted Truck SAE J1455 Operating Sinusoidal Vibe, Category 3 SAE J1455 Non-operating Sinusoidal Vibe, Category 3 SAE J1455 Handling Drop Test UL 60950-1, 2nd edition; CAN/CSA C22.2 No. 60950-1, 2nd edition, EN 60950-1, 2nd edition; CB to IEC 60950-1, 2nd edition with all group differences and national deviations 40 to158F (40 to 85C) 595%
4570 m (15,000 ft) Cisco IR829 Integrated Services Router 6-2 IMPORTANT! READ ALL THE SAFETY INFORMATION BEFORE INSTALLING THE HARDWARE Getting Started and Product Document of Compliance for the Cisco IR829 Integrated Services Router Cisco Information, page 2
Introduction, page 2 Items Shipped with your Router, page 2
Equipment that you supply, page 2
Related Documentation, page 3
Installation Warning and Caution Statements, page 4
Grounding the Router, page 5
Connecting DC Power, page 6
Connecting to the Router Gateway Ports, page 8
Connecting to the USB Port, page 8
EMC Information, page 9 Cisco Systems, Inc. www.cisco.com Cisco Information Table 1 Cisco Company Name and Address Details Company Name Cisco Systems, Inc. Cisco Address 170 West Tasman Drive, San Jose, CA 95134-1706, United States. Introduction The purpose of this document is to provide the installer the necessary information for installing the Cisco IR829 Integrated Services Router. The documentation is on-line, and subject to change. Make sure that you are downloading or viewing on-line the latest version before beginning an installation. This document also contains Product Compliance and Safety information. Items Shipped with your Router Unpack the box and verify that all items listed on the invoice were shipped with the Cisco IR829. The following items are shipped with your router:
This document Part Number 78-100611
Power Cable components
Grounding Lug
Ethernet Cable Part Number 75-1501-01 Equipment that you supply
ESD-preventive cord and wrist strap.
Wire-stripping tools for stripping 14- and 18-gauge wires
Crimping tool
Ratcheting torque screwdriver that exerts up to 15 in-lb (1.69 N-m) of pressure. Getting started with the Cisco 829 Integrated Services Router 2 78-100611-01A0 Related Documentation To access resources or to display the latest Cisco 800 Series Router documentation on-line, go to this URL:www.cisco.com/go/800 This portal has all of the information you need to get to know your router, install and configure it, as well as access software. Look at the right side of the page under Support. You will see the following categories as well as other important information:
All support information for Cisco 800 Series Routers: Provides the most requested resources and a list of all of the models in the series.
Software Downloads, Release and General Information: Links to the Software Download site, Compatibility Information, Licensing Information, and Product Release notes. Install and Upgrade: This is your starting point for Installing the Router. look under The Install and Upgrade Guide section for this model,
Configure: These links provide configuration information. Look first under the Configuration Guide section for this model. Other important and helpful links to Cisco information are here:
Cisco.com: www.cisco.com
Warranty Information: www.cisco-warrantyfinder.com
Cisco Information Packet, consisting of Cisco Limited Warranty, Disclaimer of Warranty, End User License Agreement, and United States Federal Communications Commission Notice:
www.cisco.com/en/US/docs/general/warranty/English/SL3DEN__.html
Cisco Marketplace: www.cisco.com/pcgi-bin/marketplace/welcome.pl
Cisco Product Documentation: www.cisco.com/go/techdocs
Regulatory Compliance and Safety Information:
http://www.cisco.com/en/US/docs/routers/access/800/rcsi/800srcsi.html
Cisco Support: www.cisco.com/cisco/web/support/index.html 78-100611-01A0 Getting started with the Cisco 829 Integrated Services Router 3 Installation Warning and Caution Statements Warning IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071 Warning In order to comply with FCC radio frequency (RF) exposure limits, antennas for this product should be located a minimum of 7.9 in. (20 cm) or more from the body of all persons. Statement 332 Warning Read the installation instructions before connecting the system to the power source. Statement 1004 Warning This product relies on the buildings installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 10A Statement 1005 Warning This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security. Statement 1017 Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024 Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030 Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040 Warning To prevent the system from overheating, do not operate it in an area that exceeds the maximum recommended ambient temperature of:
140F (60C) Statement 1047 Warning Use twisted-pair supply wires suitable for 86F (30C) above surrounding ambient temperature outside the enclosure. Statement 1067 Warning Installation of the equipment must comply with local and national electric codes. Statement 1074 Getting started with the Cisco 829 Integrated Services Router 4 78-100611-01A0 Warning Avoid using or servicing any equipment that has outdoor connections during an electrical storm. There may be a risk of electric shock from lightning. Statement 1088 Caution The equipment shall only be used in an area of not more than pollution degree 2, as defined in IEC 60664-1. The equipment shall be installed in a certified ATEX enclosure that provides a degree of protection not less than IP 54 in accordance with IEC 60079-15. Caution Airflow around the Router must be unrestricted. The dimensions (height x width x depth) are 7.70 x 11 x 1.73 in. (19.6 x 27.9 x 4.39 cm). To prevent the Router from overheating, there must be a minimum of 1.0 in. (25.4 mm) around all surfaces of the Router. Contact your Cisco Technical Assistance Centre (TAC) if tighter spacings are required. Caution This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D, or only nonhazardous locations. Note This equipment is rated as follows:
- DC Input Voltage: Maximum Operating Range: 9.6V to 32VDC; Nominal: 12/24 VDC Note This product is suitable for use in environmental air space in accordance with section 300.22.C of the National Electrical Code and sections 2-128, 12-010(3), and 12-100 of the Canadian Electrical Code, Part 1, C22.1. You should not install the power supply or power injector in air handling spaces. Note The maximum ambient operating temperature range is 40 to 140F (40 to 60C). Grounding the Router Make sure to follow any grounding requirements at your site. Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024 Warning This equipment is intended to be grounded to comply with emission and immunity requirements. Ensure that the switch functional ground lug is connected to earth ground during normal use. Statement 1064 Caution To make sure that the equipment is reliably connected to earth ground, follow the grounding procedure instructions, and use 14-to-16 AWG wire. 78-100611-01A0 Getting started with the Cisco 829 Integrated Services Router 5 Caution Use at least a 4 mm2 conductor to connect to the external grounding screw. The ground lug is supplied with the device. To ground the router to earth ground by using the ground screw, follow these steps:
Step 1 Step 2 Step 3 Locate the ground lug in the packaging kit. Store the ground screw for later use. Use a wire stripping tool to strip the 14-16 AWG (2.08-1.31mm) grounding wire to 0.22 in. (5.56 mm). Insert the ground wire into the ring terminal lug, and using a crimping tool, crimp the terminal to the wire. 3 6 1 2 3 3 Step 4 Step 5 Slide the ground screw through the ground lug. Insert the ground screw into one of the two screw positions shown in the graphic. Step 6 Step 7 Use a ratcheting torque screwdriver to tighten the ground screw and ring terminal to the router side panel to 3.5 in-lb
(0.4 N-m). The torque should not exceed 3.5 in-lb (0.4 N-m). Attach the other end of the ground wire to a grounded bare metal surface, such as a ground bus, a grounded DIN rail, or a grounded bare rack. Connecting DC Power Warning When you connect or disconnect the power and/or alarm connector with power applied, an electrical arc can occur. This could cause an explosion in hazardous area installations. Be sure that all power is removed from the switch and any other circuits. Be sure that power cannot be accidentally turned on or verify that the area is nonhazardous before proceeding. Statement 1058 Warning Explosion HazardThe area must be known to be nonhazardous before installing, servicing, or replacing the unit. Statement 1082 Getting started with the Cisco 829 Integrated Services Router 6 78-100611-01A0 Warning Explosion HazardSubstitution of components may impair suitability for Class I, Division 2/Zone 2. Statement 1083 Warning Connect the unit only to DC power source that complies with the safety extra-low voltage (SELV) requirements in IEC 60950 based safety standards. Statement 1033 Plugs and Pin-Outs The following is a brief overview of connecting to DC power. Details can be found in the Cisco IR829 Integrated Services Router Hardware Installation Guide and should be understood before beginning. See Related Documentation, page 3. The IR829 ships with a DC power accessory kit that contains a 4-pin locking connector and pins to use for the power connections. Four contacts are supplied, but only three are used. One is a spare. The power entry receptacle is on the IR829. The pin-outs are shown in Figure 1. Descriptions are shown in Figure 2. Figure 1 Power Connector Pin-outs Figure 2 Pin Number 1 2 3 4 Power connector Descriptions Name DC In -
Ignition DC In +
N/A Description DC Power Return (GND-) Ignition Input (IGN) DC Power In (BAT+) N/A Color Black Blue Red N/A To connect DC power:
Step 1 Identify the DC power source and measure 4 strands of copper wire 16 AWG (1.29mm) long enough to connect to the DC power source. Note The maximum length of the cable before twisting is 15 feet (4.6 meters). Step 2 Using an 16-gauge wire-stripping tool, strip each of the wires coming from each DC-input power source to 0.25 inch (6.3 mm) 0.02 inch (0.5 mm). Do not strip more than 0.27 inch (6.8 mm) of insulation from the wire. Stripping more than the recommended amount of wire can leave exposed wire from the power connector after installation. 78-100611-01A0 Getting started with the Cisco 829 Integrated Services Router 4 8 0 3 3 3 7 Step 3 Using the pins included in the kit, crimp each pin onto a wire. Step 4 Step 5 Insert the pins into the power connector, referring to previous figures 1 and 2 for guidance. Plug the connector into the power entry receptacle. Connecting to the Router Gateway Ports For hazardous location environments, follow these warnings when connecting to the destination ports
(antenna, serial, Ethernet, and console ports). Warning If you connect or disconnect the console cable with power applied to the switch or any device on the network, an electrical arc can occur. This could cause an explosion in hazardous location installations. Be sure that power is removed or the area is nonhazardous before proceeding. Statement 1080 Warning Do not connect or disconnect cables to the ports while power is applied to the switch or any device on the network because an electrical arc can occur. This could cause an explosion in hazardous location installations. Be sure that power is removed from the switch and cannot be accidentally be turned on, or verify that the area is nonhazardous before proceeding. Statement 1070 Connecting to the USB Port Note If you are connecting to the USB port:
- a connection (to the USB port) can only be made in a non-hazardous environment
- the USB port cover must be reinstalled before the router can be deployed in a hazardous environment Getting started with the Cisco 829 Integrated Services Router 8 78-100611-01A0 Hazardous Locations Standards and Marking Strings The following standards were used for the hazardous locations approvals and certifications:
ANSI/ASA 12.12.01-2013 CAN/CSA C22.2 No. 60079-0-11 Ed. 2 CAN/CSA C22.2 No. 60079-15-12 Ed. 1 CSA C22.2 No. 213-M1987+A11:2013 EN 60079-0:2012 EN 60079-15:2010 IEC 60079-0 6th Edition IEC 60079-15 4th Edition UL 60079-0, 5th Ed, 2009-10-21 UL 60079-15, 3rd Ed, 2009-7-17 The following hazardous locations strings are provided on the router:
Class 1, Div 2, Groups A B C D Class I, Zone 2, AEx nA IIC T4 Gc II 3G, Ex nA IIC T4 Gc DEMKO 15ATEX 1491X Class 1, Zone 2, AEx nA IIC T4 Gc EMC Information For EMC and safety information, see the Regulatory Compliance and Safety Information at this URL:
www.cisco.com/go/800 Class A Notice for FCC Modifying the equipment without Ciscos authorization may result in the equipment no longer complying with FCC requirements for Class A digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This device operates in the : 5150-5250, 5250-5350, 5470-5725, and 5725-5850 MHz bands and may be operated indoor or outdoors per FCC guidance. 78-100611-01A0 Getting started with the Cisco 829 Integrated Services Router 9 This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and radiates radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference. However, there is no guarantee that interference will not occur. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from which the receiver is connected.
Consult the dealer or an experienced radio/TV technician. Caution The Part 15 radio device operates on a non-interference basis with other devices operating at this frequency when using the integrated antennas. Any changes or modification to the product not expressly approved by Cisco could void the user's authority to operate this device. Caution Within the 5.15 to 5.25 GHz and 5.47-5.725 GHz bands, this device is restricted to indoor operations to reduce any potential for harmful interference to co-channel Mobile Satellite System (MSS) operations. Industry Canada Canadian Compliance Statement Cisco 829 Industrial Integrated Services Router Model IR829GW-LTE Cisco 829 Industrial Integrated Services Router PIDS
IR829GW-LTE-VZ-AK9 IR829GW-LTE-NA-AK9 IR829GW-LTE-ST-AK9 Industry Canada Certification Number
2461B-IR829GW-LTE This Class A Digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations. This device complies with Class A Limits of Industry Canada. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Cisco 829 Industrial Integrated Services Routers are certified to the requirements of RSS-210. The use of this device in a system operating either partially or completely outdoors may require the user to obtain a license for the system according to the Canadian regulations. For further information, contact your local Industry Canada office. This device has been designed to operate with antennas having a maximum gain of 6 dBi. Antennas having a gain greater than 6 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. Getting started with the Cisco 829 Integrated Services Router 10 78-100611-01A0 To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotopically radiated power (EIRP) is not more than that permitted for successful communication. Operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. Users are advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. European Community, Switzerland, Norway, Iceland, and Liechtenstein Cisco 829 Industrial Integrated Services Router PIDS
IR829GW-LTE-VZ-AK9 IR829GW-LTE-NA-AK9 IR829GW-LTE-ST-AK9 Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC & Medical Directive 93/42/EEC The following standards were applied:
EMC-EN 301.489-1 v1.9.2; EN 301.489-17 v2.2.1
Health & Safety-EN60950-1: 2005; EN 50385: 2002
Radio-EN 300 328 v 1.9.1; EN 301.893 v 1.7.1, EN62311 The conformity assessment procedure referred to in Article 10.4 and Annex III of Directive 1999/5/EC has been followed. This device also conforms to the EMC requirements of the Medical Devices Directive 93/42/EEC. Note This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation. For more details, contact Cisco Corporate Compliance. The product carries the CE Mark:
Declaration of Conformity for RF Exposure This section contains information on compliance with guidelines related to RF exposure. Generic Discussion on RF Exposure The Cisco products are designed to comply with the following national and international standards on Human Exposure to Radio Frequencies:
US 47 Code of Federal Regulations Part 2 Subpart J
American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers /
IEEE C 95.1 (99) 78-100611-01A0 Getting started with the Cisco 829 Integrated Services Router 11
International Commission on Non Ionizing Radiation Protection (ICNIRP) 98
Ministry of Health (Canada) Safety Code 6. Limits on Human Exposure to Radio Frequency Fields in the range from 3kHz to 300 GHz
Australia Radiation Protection Standard To ensure compliance with various national and international Electromagnetic Field (EMF) standards, the system should only be operated with Cisco approved antennas and accessories. This Device Meets International Guidelines for Exposure to Radio Waves The IR829 series device includes a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves (radio frequency electromagnetic fields) recommended by international guidelines. The guidelines were developed by an independent scientific organization (ICNIRP) and include a substantial safety margin designed to ensure the safety of all persons, regardless of age and health. As such the systems are designed to be operated as to avoid contact with the antennas by the end user. It is recommended to set the system in a location where the antennas can remain at least a minimum distance as specified from the user in accordance to the regulatory guidelines which are designed to reduce the overall exposure of the user or operator. Separation Distance MPE 0.63 mW/cm2 Distance 20 cm (7.87 inches) Limit 1.00 mW/cm2 The World Health Organization has stated that present scientific information does not indicate the need for any special precautions for the use of wireless devices. They recommend that if you are interested in further reducing your exposure then you can easily do so by reorienting antennas away from the user or placing he antennas at a greater separation distance then recommended. This Device Meets FCC Guidelines for Exposure to Radio Waves The IR829 series device includes a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves (radio frequency electromagnetic fields) as referenced in FCC Part 1.1310. The guidelines are based on IEEE ANSI C 95.1 (92) and include a substantial safety margin designed to ensure the safety of all persons, regardless of age and health. As such the systems are designed to be operated as to avoid contact with the antennas by the end user. It is recommended to set the system in a location where the antennas can remain at least a minimum distance as specified from the user in accordance to the regulatory guidelines which are designed to reduce the overall exposure of the user or operator. The device has been tested and found compliant with the applicable regulations as part of the radio certification process. Separation Distance MPE 0.63 mW/cm2 Distance 20 cm (7.87 inches) Limit 1.00 mW/cm2 The US Food and Drug Administration has stated that present scientific information does not indicate the need for any special precautions for the use of wireless devices. The FCC recommends that if you are interested in further reducing your exposure then you can easily do so by reorienting antennas away from the user or placing the antennas at a greater separation distance then recommended or lowering the transmitter power output. Getting started with the Cisco 829 Integrated Services Router 12 78-100611-01A0 This Device Meets the Industry Canada Guidelines for Exposure to Radio Waves The IR829 series device includes a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves (radio frequency electromagnetic fields) as referenced in Health Canada Safety Code 6. The guidelines include a substantial safety margin designed into the limit to ensure the safety of all persons, regardless of age and health. As such the systems are designed to be operated as to avoid contact with the antennas by the end user. It is recommended to set the system in a location where the antennas can remain at least a minimum distance as specified from the user in accordance to the regulatory guidelines which are designed to reduce the overall exposure of the user or operator. Separation Distance MPE 0.63 mW/cm2 Distance 20 cm (7.87 inches) Limit 1.00 mW/cm2 Health Canada states that present scientific information does not indicate the need for any special precautions for the use of wireless devices. They recommend that if you are interested in further reducing your exposure you can easily do so by reorienting antennas away from the user, placing the antennas at a greater separation distance than recommended, or lowering the transmitter power output. Additional Information on RF Exposure You can find additional information on the subject at the following links:
Cisco Systems Spread Spectrum Radios and RF Safety white paper at this URL:
http://www.cisco.com/warp/public/cc/pd/witc/ao340ap/prodlit/rfhr_wi.htm
FCC Bulletin 56: Questions and Answers about Biological Effects and Potential Hazards of Radio Frequency Electromagnetic Fields
FCC Bulletin 65: Evaluating Compliance with the FCC guidelines for Human Exposure to Radio Frequency Electromagnetic Fields
FCC Bulletin 65C (01-01): Evaluating Compliance with the FCC guidelines for Human Exposure to Radio Frequency Electromagnetic Fields: Additional Information for Evaluating Compliance for Mobile and Portable Devices with FCC limits for Human Exposure to Radio Frequency Emission You can obtain additional information from the following organizations:
World Health Organization Internal Commission on Non-Ionizing Radiation Protection at this URL: www.who.int/emf
United Kingdom, National Radiological Protection Board at this URL: www.nrpb.org.uk
Cellular Telecommunications Association at this URL: www.wow-com.com
The Mobile Manufacturers Forum at this URL: www.mmfai.org EMC Class A Notices and Warnings Statement 340Class A Warning for CISPR22 Warnung Dies ist ein Produkt der Klasse A. Bei der Verwendung dieses Produkts im Haus- oder Wohnungsbereich kann es zu Funkstrungen kommen. In diesem Fall muss der Benutzer u. U. angemessene Manahmen ergreifen. 78-100611-01A0 Getting started with the Cisco 829 Integrated Services Router 13 Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R) 2015 Cisco Systems, Inc. All rights reserved. Printed in the USA on recycled paper containing 10% postconsumer waste. Getting started with the Cisco 829 Integrated Services Router 14 78-100611-01A0
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2016-02-26 | 5745 ~ 5825 | NII - Unlicensed National Information Infrastructure TX | Class II Permissive Change |
2 | 2015-09-01 | 2412 ~ 2462 | DTS - Digital Transmission System | Original Equipment |
3 | 5745 ~ 5825 | NII - Unlicensed National Information Infrastructure TX |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 3 | Effective |
2016-02-26
|
||||
1 2 3 |
2015-09-01
|
|||||
1 2 3 | Applicant's complete, legal business name |
Cisco Systems Inc
|
||||
1 2 3 | FCC Registration Number (FRN) |
0004968939
|
||||
1 2 3 | Physical Address |
125 West Tasman Drive
|
||||
1 2 3 |
San Jose, CA
|
|||||
1 2 3 |
United States
|
|||||
app s | TCB Information | |||||
1 2 3 | TCB Application Email Address |
b******@baclcorp.com
|
||||
1 2 3 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 2 3 | Grantee Code |
LDK
|
||||
1 2 3 | Equipment Product Code |
IR829GW-LTE
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 3 | Name |
G**** T******
|
||||
1 2 3 | Title |
Manager, Engineering
|
||||
1 2 3 | Telephone Number |
408-5********
|
||||
1 2 3 | Fax Number |
408-5********
|
||||
1 2 3 |
g******@cisco.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 2 3 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 2 3 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 2 3 | If so, specify the short-term confidentiality release date (MM/DD/YYYY format) | 05/25/2016 | ||||
1 2 3 | 02/27/2016 | |||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 3 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 3 | Equipment Class | NII - Unlicensed National Information Infrastructure TX | ||||
1 2 3 | DTS - Digital Transmission System | |||||
1 2 3 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | IR829 Integrated Services Router | ||||
1 2 3 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | Yes | ||||
1 2 3 | No | |||||
1 2 3 | Modular Equipment Type | Does not apply | ||||
1 2 3 | Purpose / Application is for | Class II Permissive Change | ||||
1 2 3 | Original Equipment | |||||
1 2 3 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | Yes | ||||
1 2 3 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 2 3 | Grant Comments | Class II Permissive Change of adding DFS bands documented in this filing. This device has 20 MHz and 40 MHz bandwidth modes. Output power listed is conducted. Device operates with specific antennas in MIMO configurations as described in this filing. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and not be co-located with any other transmitters except in accordance with FCC multi-transmitter product procedures. Users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. | ||||
1 2 3 | Output power listed is conducted. Device operates with specific antennas in MIMO configurations as described in this filing. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and not be co-located with any other transmitters except in accordance with FCC multi-transmitter product procedures. Users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. | |||||
1 2 3 | This device has 20 MHz and 40 MHz bandwidth modes. Output power listed is conducted. Device operates with specific antennas in MIMO configurations as described in this filing. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and not be co-located with any other transmitters except in accordance with FCC multi-transmitter product procedures. Users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. | |||||
1 2 3 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 3 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 3 | Firm Name |
Bay Area Compliance Laboratories Corporation
|
||||
1 2 3 | Name |
L****** T******
|
||||
1 2 3 | Telephone Number |
408-7******** Extension:
|
||||
1 2 3 | Fax Number |
408 7********
|
||||
1 2 3 |
l******@baclcorp.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15E | 38 CC MO | 5180 | 5240 | 0.179 | |||||||||||||||||||||||||||||||||||
1 | 2 | 15E | 38 CC MO ND | 5260 | 5320 | 0.136 | |||||||||||||||||||||||||||||||||||
1 | 3 | 15E | 38 CC MO ND | 5500 | 5700 | 0.161 | |||||||||||||||||||||||||||||||||||
1 | 4 | 15E | 38 CC MO | 5745 | 5825 | 0.376 | |||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 15C | CC MO | 2412.00000000 | 2462.00000000 | 0.2740000 | |||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
3 | 1 | 15E | 38 CC MO | 5180 | 5240 | 0.179 | |||||||||||||||||||||||||||||||||||
3 | 2 | 15E | 38 CC MO | 5745 | 5825 | 0.376 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC