Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide First Published: 2023-08-04 Last Modified: 2023-08-04 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 C O N T E N T S Preface vii About this Guide vii Conventions vii Related Documentation vii Communications, Services, and Additional Information vii Cisco Bug Search Tool viii Documentation Feedback viii C H A P T E R 1 About Cisco Catalyst IW9165E Rugged Access Point and Wireless Client 1 Introduction to Cisco Catalyst IW9165E Rugged Access Point and Wireless Client 1 Cisco Catalyst IW9165E Features 1 Connectors and Ports 2 4-Pin Micro-Fit Connector for DC Power 3 M12-RJ45 Adapter 3 Power Sources 4 Power Adapters 5 Power Injectors 5 Ethernet (PoE) Ports 5 Antennas and Radios 6 Supported External Antennas 6 Unpacking Your Access Point 11 Package Contents 11 Unpacking the Access Point 11 Cisco Orderable Accessories 11 C H A P T E R 2 Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide Contents C H A P T E R 3 Installation Overview 15 Preinstallation Checks and Installation Guidelines 15 Mounting the Access Point 16 Mounting on a Wall 16 Installing a DIN Rail 17 Mounting the DIN Rail Bracket on the Access Point 17 Attaching the Bracket onto the DIN Rail 18 Removing the Access Point from the DIN Rail 19 Installing a Lightning Arrestor 19 Lightning Arrestor Installation Notes 19 Grounding the Access Point 20 Powering the Access Point 22 Connecting a Power Injector 22 Troubleshooting 25 Using the Reset Button 25 Checking the Access Point LEDs 25 Safety Guidelines and Warnings 29 Safety Instructions 29 FCC Safety Compliance Statement 30 Safety Precautions 30 Safety Precautions when Installing Antennas 31 Avoiding Damage to Radios in a Testing Environment 31 Performing Site Surveys 32 C H A P T E R 4 C H A P T E R 5 C H A P T E R 6 Declarations of Conformity and Regulatory Information 35 Manufacturers Federal Communication Commission Declaration of Conformity Statement 35 Operation of Cisco Catalyst Access Points in Mxico 36 VCCI Statement for Japan 36 Statement 191Voluntary Control Council for Interference (VCCI) Class A Warning for Japan 36 191 VCCI A 37 Guidelines for Operating Cisco Catalyst Access Points in Japan 37 Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide iv Contents Compliance Statement for Canada 38 Industry Canada 38 European Community, Switzerland, Norway, Iceland, and Liechtenstein 39 United Kingdom Compliance 39 Declaration of Conformity for RF Exposure 40 Generic Discussion on RF Exposure 40 This Device Meets International Guidelines for Exposure to Radio Waves 40 This Device Meets FCC Guidelines for Exposure to Radio Waves 41 This Device Meets the Industry Canada Guidelines for Exposure to Radio Waves 41 Cet appareil est conforme aux directives internationales en matire d'exposition aux frquences radiolectriques 42 Additional Information on RF Exposure 42 Declaration of Conformity Statements 42 Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide v Preface This preface describes this guide and provides information about the conventions used in this guide, and related documentation. It includes the following sections:
About this Guide This guide provides instructions to install your Cisco Access Point and provides links to resources that can help you configure it. This guide also provides mounting instructions and troubleshooting information. Conventions This document uses the following conventions for notes, cautions, and safety warnings. Notes and cautions contain important information that you should know. Means reader take note. Notes contain helpful suggestions or references to material not covered in the manual. Means reader be careful. Cautions contain information about something you might do that could result in equipment damage or loss of data. Note Caution Warning Safety warnings appear throughout this guide in procedures that, if performed incorrectly, can cause physical injuries. A warning symbol precedes each warning statement. Related Documentation All user documentation for the Cisco Catalyst IW9165 Rugged Series is available at the following URL:
https://www.cisco.com/c/en/us/support/wireless/catalyst-iw9165-rugged-series/series.html For detailed information and guidelines about configuring and deploying your access point in a wireless network, see the relevant release of Wireless Controller configuration guide at the following URL:
https://www.cisco.com/c/en/us/support/wireless/catalyst-9800-series-wireless-controllers/
products-installation-and-configuration-guides-list.html Communications, Services, and Additional Information To receive timely, relevant information from Cisco, sign up at Cisco Profile Manager. To get the business impact youre looking for with the technologies that matter, visit Cisco Services. Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide vii Cisco Bug Search Tool Preface To submit a service request, visit Cisco Support. To discover and browse secure, validated enterprise-class apps, products, solutions, and services, visit Cisco DevNet. To obtain general networking, training, and certification titles, visit Cisco Press. To find warranty information for a specific product or product family, access Cisco Warranty Finder. Cisco Bug Search Tool Cisco Bug Search Tool (BST) is a gateway to the Cisco bug-tracking system, which maintains a comprehensive list of defects and vulnerabilities in Cisco products and software. The BST provides you with detailed defect information about your products and software. Documentation Feedback To provide feedback about Cisco technical documentation, use the feedback form available in the right pane of every online document. Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide C H A P T E R 1 About Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Introduction to Cisco Catalyst IW9165E Rugged Access Point and Wireless Client, on page 1 Cisco Catalyst IW9165E Features, on page 1 Connectors and Ports, on page 2 Power Sources, on page 4 Antennas and Radios, on page 6 Introduction to Cisco Catalyst IW9165E Rugged Access Point and Wireless Client The Cisco Catalyst IW9165E Rugged Access Point and Wireless Client (hereafter referred to as IW9165E) is designed to add ultrareliable wireless connectivity to moving vehicles and machines. The IW9165E runs Cisco Ultra-Reliable Wireless Backhaul (Cisco URWB), which delivers high availability, low latency, and zero packet loss with seamless handoffs. The IW9165E can also operate as a Wi-Fi client in Workgroup Bridge (WGB) mode, which allows it to connect to a Cisco access point infrastructure, and Universal WGB (uWGB) mode, which allows it to connect to a third-party access point infrastructure. Both of these modes help bridge the wired clients that are behind the WGB to the access point on the infrastructure side. A full listing of the AP's features and specifications is provided in the Cisco Catalyst IW9165 Series Data Sheet. Cisco Catalyst IW9165E Features Cisco Catalyst IW9165E Rugged Access Point and Wireless Client has the following features:
1x 100M/1000M/2.5G Multigigabit Ethernet (RJ45)/M12 X-code autosensing PoE+ in (802.3af/at), Cisco UPOE in 1x 100M/1000M/1G (RJ45) Dual-radio architecture 5-GHz 2x2 radio: 20, 40, and 80 MHz channels Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 1 Connectors and Ports About Cisco Catalyst IW9165E Rugged Access Point and Wireless Client 5/6-GHz 2x2 radio: 20, 40, 80, and 160 MHz channels (6 GHz availability subject to country approvals) External antenna4 x RP-SMA 1x SMA GNSS antenna portA built-in GNSS (Global Navigation Satellite System) receiver provides coordinates to track the location of the access point. 1x GPIO portsA 3-pin GPIO (general-purpose input output) enables control of external contacts. Management console port (RJ45) Dual power inputPoE-in 802.3af/at, POE+ and 24-48VDC Dual mounting optionsDIN rail and wall mount IP30, EN50155 Multicolor system LED, Received signal strength indicator (RSSI) LED, Port LED Reset button Connectors and Ports The following figures show the available ports on the AP front panel. Figure 1: IW9165E Front Panel 1 DC power input 2 Digital I/O Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 2 About Cisco Catalyst IW9165E Rugged Access Point and Wireless Client 4-Pin Micro-Fit Connector for DC Power 3 5 7 Status LED 100M/1000M/1G (RJ45) 4 6 100M/1000M/2.5G Multigigabit Ethernet
(RJ45)/M12 X-code autosensing PoE+ in
(802.3af/at), Cisco UPOE in Console port (RJ-45) and reset button (on the right-side panel) 8 GNSS port Antenna ports Antenna 15 GHz and IoT radio Antenna 25 GHz Antennas 3 and 45/6 GHz 4-Pin Micro-Fit Connector for DC Power The following figure shows the 4-pin Micro-Fit connector for DC power. Figure 2: Mating Connector Front View Molex Micro-Fit Pin Pin 1 Pin 2 Pin 3 Pin 4 Assignment Black ( - Negative Terminal) Not assigned White (+ Positive Terminal) Not assigned M12-RJ45 Adapter M12-RJ45 adapter (Cisco PID: IW-ACC-M12ETH=) can be used to support M12 X-coded connector. Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 3 Power Sources About Cisco Catalyst IW9165E Rugged Access Point and Wireless Client M12 X-code port by using M12-RJ45 adapter can support up to 2.5G rate. Note Note The M12 spacer (Cisco PID: IW-ACC-M12SPCR2= ) is required when using the M12 adapter. Figure 3: M12-RJ45 Adapter (Cisco PID: IW-ACC-M12ETH=) The following table shows the M12-RJ45 adapter pinouts. Table 1: M12-RJ45 Pinouts RJ45 1 2 3 6 7 8 5 4 Signal B1_DA+
B1_DA-
B1_DB+
B1_DB-
B1_DD+
B1_DD-
B1_DC-
B1_DC+
M12 X-Code 1 2 3 4 5 6 7 8 Power Sources The IW9165E is supported on these power sources:
DC power: 24 to 48 VDC Power over Ethernet (PoE): 802.3at (PoE+), 802.3bt (PoE++), Cisco Universal PoE (Cisco UPOE). Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 4 About Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Power Adapters Warning Connect the unit only to DC power source that complies with the safety extra-low voltage (SELV) requirements in IEC 62368 based safety standards. Statement 1033 Power Adapters The IW9165E supports the following DC power adapters::
PID: IW-PWRADPT-MFIT4P=: Operating: -40C to +65C, 60W. Power Injectors The IW9165E supports the following power injectors:
IW-PWRINJ-60RGDMG=: Operating: -40C to +70C. Power derating of 60W at 70C, and 65W at 65C. Supports 100M/1G/2.5G/5G/10G rates. Warning Caution To reduce the risk of fire, use only No. 24 AWG or larger telecommunications line cord. Statement 1023 When the AP is installed outdoors or in a wet or damp location, the AC branch circuit powering the AP should be provided with ground fault protection (GFCI), as required by Article 210 of the National Electrical Code
(NEC). Ethernet (PoE) Ports The AP supports an Ethernet uplink port (also for PoE-IN). The Ethernet uplink port on the AP uses an RJ-45 connector to link the AP to the 100BASE-T, 1000BASE-T, or 2.5G BASE-T network. The Ethernet cable is used to send and receive Ethernet data and optionally supply inline power from the power injector or a suitably powered switch port. The AP senses the Ethernet and power signals, and automatically switch internal circuitry to match the cable connections. Tip Danger To reduce the risk of fire, use only No. 24 AWG or larger telecommunication line cord. Statement 1023 The Ethernet cable must be a shielded, outdoor rated, Category 5e (CAT 5e) or better cable. Category 6A
(CAT 6A) cable is needed for 5G rate. The AP senses the Ethernet and power signals and automatically switches internal circuitry to match the cable connections. Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 5 Antennas and Radios About Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Antennas and Radios The Cisco Catalyst IW9165E Rugged Access Point and Wireless Client configuration is:
IW9165E-x The IW9165E access point has four RP-SMA jack connectors to support multiple antenna options, such as the self-identifying antennas (SIA) on designated two SIA ports, dual-band antennas, and single-band antennas. To see the list of supported antennas and the radio bands they operate at, see Supported External Antennas, on page 6. Supported External Antennas The following figure shows the antenna ports of the IW9165E access point. Figure 4: IW9165E Antenna Ports 1 3 5 Port 1 Supports 5 GHz in 2x2 mode. Supports Bluetooth Low Energy (BLE) radio. Supports SIA. Port 3 Supports 5/6 GHz radio in 2x2 mode. Supports SIA. 2 4 GNSS port Port 2 Supports 5 GHz radio in 2x2 mode. Port 4 Supports 5/6 GHz radio in 2x2 mode. Supported Wi-Fi Antennas The following table shows the external Wi-Fi antennas supported by IW9165E. Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 6 About Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Supported External Antennas Table 2: Supported Wi-Fi Antennas PID IW-ANT-PNL-515-N=
Antenna Gain (dBi) Connector Antenna Name 2.4 GHz 4.9 GHz 15 5 GHz 15 N male (x2) Cisco 5 GHz 15 dBi Dual-Port Polarization Diverse Directional Panel Antenna W-ANTM2050D-RPSMA 2 IW-ANT-OMV-2567-N= 4 IW-ANT-OMH-2567-N= 4 AIR-ANT2547V-N=
AIR-ANT2547VG-N=
4 4 AIR-ANT2547VG-NS=
4 AIR-ANT2568VG-N=
6 AIR-ANT2568VG-NS=
6 7 7 AIR-ANT5180V-N=
7 4 7 7 7 7 7 8 8 8 RP-SMA N male N male N male N male N male N male N male N male AIR-ANT2588P4M-NS= 9.1 (V), 7.1 (H) 9.6 (V), 7.8 (H) N female
(x4) Cisco Indoor Swivel-Mount Dual-Band Dipole Antenna 2.4/5 GHz Tri-Band Omnidirectional Dipole Antenna, Vertically Polarized, Self-Identifying 2.4/5 GHz Tri-Band Omnidirectional Dipole Antenna, Horizontally Polarized, Self-Identifying Cisco Aironet Dual-Band Omnidirectional Dipole Antenna
(White) Cisco Aironet Dual-Band Omnidirectional Dipole Antenna
(Gray) Cisco Aironet Dual-Band Omnidirectional Dipole Antenna
(Gray), Self-Identifying Cisco Aironet Dual-Band Omnidirectional Dipole Antenna
(Gray) Cisco Aironet Dual-Band Omnidirectional Dipole Antenna
(Gray), Self-Identifying Cisco Aironet 5 GHz 8 dBi Omnidirectional Dipole Antenna Cisco Aironet 2.4/5 GHz 8 dBi 4-Element Dual-Polarized Patch Antenna, Self-Identifying AIR-ANT5114P2M-N=
13 N male (x2) Cisco Aironet 5 GHz 13 dBi Dual-Port Dual-Polarized Directional Panel Antenna Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 7 Supported External Antennas About Cisco Catalyst IW9165E Rugged Access Point and Wireless Client PID Antenna Gain (dBi) Connector Antenna Name AIR-ANT2513P4M-N1=
13 AIR-ANT2513P4M-NS2=
13 N female
(x4) N female
(x4) Cisco Aironet Four-Port Dual-Band Polarization-Diverse Directional Panel Antenna Cisco Aironet Four-Port Dual-Band Polarization-Diverse Directional Panel Antenna, Self-Identifying AIR-ANT2513P4M-N1 - Only supports 5GHz bands. AIR-ANT2513P4M-N1 - Only supports 5GHz bands. BLE Supports Max 8dBi antenna gain. For installation instructions and detailed information on any of these antennas, refer to the antenna data sheet on Cisco.com, or see the antenna guides at:
Cisco Industrial Routers and Industrial Wireless Access Points Antenna Guide http://www.cisco.com/c/en/us/support/wireless/aironet-antennas-accessories/
products-installation-guides-list.html Follow all safety precautions when installing the antennas. For information on safety, see Safety Precautions when Installing Antennas, on page 31. Supported URWB Antennas Table 3: Supported URWB Antennas PID Antenna Gain (dBi) Connector Antenna Name 2.4 GHz 4.9 GHz 5 GHz IW-ANT-OMM-53-N=
IW-ANT-PNL-59-N=
IW-ANT-SKS-514-Q=
IW-ANT-SKD-513-Q=
3 14 13 3 9 14 13 N female N female
(x2) 5 GHz Omnidirectional Multi-Polarized Antenna 5 GHz Dual-Port Dual-Slant +/-45 Degree Polarized Directional Panel Antenna QMA female (x2) 5 GHz Directional Shark Antenna, Dual-Slant +/-45 Degree Polarized QMA female (x2) 5 GHz Bidirectional Shark Antenna, Dual-Slant +/-45 Degree Polarized Supported GNSS Antenna The following table shows the external GNSS antennas supported by IW9165E. Table 4: Supported GNSS Antenna PID Frequencies Supported Connector Description ANT-GNSS-OUT-TNC= 1560 - 1608 MHz TNC male Outdoor Active GNSS Antenna with 15-ft. integrated cable Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 8 About Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Supported External Antennas PID Frequencies Supported Connector Description IW-ANT-GNSS-SMA= 1559 - 1610 MHz SMA male Indoor/outdoor active GNSS antenna with 10-ft. integrated cable Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 9 C H A P T E R 2 Unpacking Your Access Point Package Contents, on page 11 Unpacking the Access Point, on page 11 Cisco Orderable Accessories, on page 11 Package Contents Each AP package contains the following items:
One IW9165E AP Ground lug kit Unpacking the Access Point To unpack the AP, follow these steps:
Step 1 Step 2 Step 3 Unpack and remove the access point and the selected mounting accessory kit from the shipping box. Return the packing material to the shipping container and save it for future use. Verify that you have received all items ordered. If any item is missing or damaged, contact your Cisco representative or reseller for instructions. Cisco Orderable Accessories Order the following accessories separately from Cisco:
AP mounting brackets Cisco PID Description IR1101-DINRAIL=
DIN Rail Mounting Bracket Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 11 Cisco Orderable Accessories Unpacking Your Access Point Cisco PID Description IR1101-WALLMNT=
Wall Mounting Bracket Accessory kits Cisco PID IW-ACC-M12ETH=
IW-ACC-M12PWR=
Description Adapter, M12 X-code to RJ45 Ethernet connector Adapter, M12 4 Pin A-Code to Micro-fit power connector IW-ACC-M12SPCR2=
Spacer for M12 (Qty: 5) M12 Cables Cisco PID CAB-PWR-M12-10=
CAB-RJ45-M12-10=
RF Coaxial Adapters Cisco PID AIR-ACC370-NF-NF=
LTE-ADPT-SM-TF=
RF Coaxial Cables Cisco PID CAB-L400-5-N-N=
CAB-L400-5-N-NS=
AIR-CAB010LL-N=
CAB-L400-20-N-N=
AIR-CAB025HZ-N=
CAB-L600-30-N-N=
CAB-L240-10-Q-N=
CAB-L240-15-Q-N=
CAB-L240-20-Q-N=
Lightning Arrestors Description M12 DC power cable, 4 pins, A-Code, 10 ft M12 to RJ-45 Ethernet cable, 8 pins, X-Code, 10 ft Description N(f) to N(f) RF adapter DC-11 GHz SMA(m) to TNC(f) RF adapter, DC-11 GHz Description 5 ft. LMR-400-DB, N(m)-STR to N(m)-R/A 5 ft. LMR-400-DB, N(m)-STR to N(m)-STR 10 ft. LMR-400-DB, N(m)-STR to N(m)-STR 20 ft. LMR-400-DB, N(m)-STR to N(m)-RA 25 ft. LMR-400-DB/FR/CMR, N(m)-STR to N(m)-RA 30 ft. LMR-600-DB, N(m)-STR to N(m)-RA 10 ft. LMR-240-FR/CMR, N(m)-STR to QMA(m)-RA 15 ft. LMR-240-FR/CMR, N(m)-STR to QMA(m)-RA 20 ft. LMR-240-FR/CMR, N(m)-STR to QMA(m)-RA Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide Unpacking Your Access Point Cisco Orderable Accessories Lightning Arrestor CGR-LA-NM-NF=
CGR-LA-NF-NF=
ACC-LA-G-TM-TF=
ACC-LA-G-TF-TF=
Description Lightning Arrestor kit, N(m) to N(f) Lightning Arrestor kit, N(f) to N(f) Lightning Arrestor kit, TNC(f) for GNSS Lightning Arrestor kit, TNC(f) to TNC(f) Power adapter and power injectors when PoE is not available Power Supply Description IW-PWRADPT-MFIT4P=
Power Adapter, AC-DC, Micro-Fit 4-Pin connector IW-PWRINJ-60RGDMG=
Power Injector, 60W, outdoor 5GE Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 13 C H A P T E R 3 Installation Overview Preinstallation Checks and Installation Guidelines, on page 15 Mounting the Access Point, on page 16 Installing a Lightning Arrestor, on page 19 Grounding the Access Point, on page 20 Powering the Access Point, on page 22 Preinstallation Checks and Installation Guidelines Before you mount and deploy your access point, we recommend that you perform a site survey (or use the Site Planning tool) to determine the best location to install your access point. You should have the following information about your wireless network available:
Access point locations Access point mounting options: To a vertical or horizontal wall or a DIN rail Access point power options: Use either of the following options to power the AP:
DC power input Cisco-approved power injector 802.3at (PoE+), 802.3bt, and Cisco Universal PoE (Cisco UPOE) Operating temperature: -4 to +122F (-20 to +50C) with still air. Console access using the console port We recommend that you use a console cable that is one meter or less in length. Note The AP may face issues while booting if you use an unterminated console cable
(not plugged into any device or terminal) or a console cable that is more than one meter in length. Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 15 Mounting the Access Point Installation Overview We recommend that you make a site map showing access point locations so that you can record the device MAC addresses from each location and return them to the person who is planning or managing your wireless network. Mounting the Access Point Mounting on a Wall The IW9165E can be mounted in a vertical or horizontal orientation. It can be mounted to a wall or other flat surface, and can also be mounted to a DIN rail. When choosing a location for wall-mounting an access point, consider cable limitations and wall structure, and consider suitable antenna location ahead of time. Read the wall-mounting instructions carefully before beginning installation. Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system. Statement 378 Tip Warning Warning A minimum of 1 inch clearance is required on all sides of the device except for the side mounted against the wall or DIN rail, to allow for proper air flow. The wall mounting kit contains the following:
Mounting brackets (x2) Mounting screws (x4) M4 x 6mm To mount the access point on a wall or other flat surface, follow these steps:
Step 1 Attach the mounting brackets to the bottom of the access point. Refer to the following for guidance. Figure 5: IW9165E Mounting Bracket Step 2 Align the mounting brackets (1) over the mounting holes (3) so that the larger holes on the brackets extend out over the access point. Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 16 Installation Overview Installing a DIN Rail Step 3 Step 4 Attach the brackets to the access point with the 4 screws (2) provided using a Phillips head driver. Torque to 13-15 in. lbs. Mount the access point with the attached brackets in a proper wall structure to carry the weight of the device. See the following for the dimensions of the mounting holes with the brackets attached to the access point Figure 6: Wall Mounting Hole Dimensions With Mounting Brackets Attached Note Four #10-32 screws are recommended when mounting the unit with these brackets attached to the neighboring surface. Figure 7: Wall Mounting Clearance and Overall Dimensions With Mounting Brackets Attached Step 5 Route the cables so that they do not put a strain on the connectors or mounting hardware. Installing a DIN Rail The DIN Rail kit is ordered separately. The DIN Rail can be installed on the IW9165E in two different orientations, horizontally and vertically. Note Warning A minimum of 1 inch clearance is required on all sides of the device except for the side mounted against the wall or DIN rail, to allow for proper air flow. To attach the DIN rail bracket to the IW9165E, follow these steps. Mounting the DIN Rail Bracket on the Access Point Step 1 First, attach the DIN rail bracket to the back of the access point. The DIN rail bracket mounts in two different ways, depending on the orientation you wish to use. See the following two figures for vertical orientation, and for horizontal orientation. Figure 8: Attaching the DIN Rail Bracket for Vertical Mounting 1 2 3 DIN mounting bracket Screws from kit Mounting holes Note Position the access point with the ground lug facing down for vertical mounting. Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 17 Attaching the Bracket onto the DIN Rail Installation Overview Figure 9: Attaching the DIN Rail Bracket for horizontal mounting 1 2 3 DIN mounting bracket Screws from kit Mounting holes Note Position the access point with the front ports facing down for horizontal mounting. Step 2 Step 3 Attach the DIN mounting bracket to the access point using the two screws provided in the kit. Position the bracket over the two mounting holes that correspond to your orientation. Use 13-15 in. lbs. of torque to screw the bracket onto the access point. Once the bracket is attached to the access point, it can be mounted onto the DIN Rail. Attaching the Bracket onto the DIN Rail To attach the Cisco IW9165E with the bracket to a DIN rail, follow these steps. Refer to the following figure for details of a completed attachment. Figure 10: Bracket Attached to the DIN Rail 1 2 DIN rail bracket DIN rail Step 1 Step 2 Position the access point so that the lower edge and spring of the DIN clip, located within the bottom of the DIN rail bracket, engages with the bottom section of the DIN rail. Push up to compress the spring. Rotate the access point so that the top hook of the DIN clip clamps to the top section of DIN rail. Refer to the following figures. What to do next Note Note The procedure to attach the unit to the rail is the same with both orientations. In order to prevent excessive side to side movement of the unit it is advised to install DIN rail stop plates such as Mouser part Numbers 653-PFP-M, 651-1201662 or 845-CA402. These stop plates can be installed on one or both sides of the unit to limit excessive side to side movement that typically occurs in high vibration environments. Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 18 Installation Overview Removing the Access Point from the DIN Rail Removing the Access Point from the DIN Rail To remove the Cisco IW9165E with the bracket from the DIN rail, follow these steps. Step 1 Step 2 Step 3 Press up on the access point to compress the spring in the DIN rail clip. Grasp the upper part of the access point and rotate it away from the DIN rail. Refer to the following figure. Lower the access point away from the DIN rail and remove it. Refer to the following figure. Installing a Lightning Arrestor Overvoltage transients can be created through lightning static discharges, switch processes, direct contact with power lines, or through earth currents. The Lightning Arrestor limits the amplitude and duration of disturbing interference voltages and improves the over voltage resistance of in-line equipment, systems, and components. A lightning arrestor installed according to these mounting instructions balances the voltage potential, thus preventing inductive interference to parallel signal lines within the protected system. Installation Considerations Cisco recommends that you bulkhead mount the lightning arrestor so it can be installed as a wall-feed through on the wall of the protected space. The importance of obtaining a good ground and bonding connection cannot be overstressed. Consider these points when grounding the lightning arrestor:
Connect the lightning arrestor components directly to the grounding point. The contact points of the ground connection must be clean and free of dust and moisture. Tighten threaded contacts to the torque specified by the manufacturer. Lightning Arrestor Installation Notes This lightning arrestor is designed to be installed between the antenna cable that is attached to an outdoor antenna and the Cisco wireless device. You can install the lightning arrestor either indoors or outdoors. It can be connected directly to a wireless device having an external N connector. It can also be mounted inline or as a feed-through. Feed-through installations require 5/8 in. (16 mm) hole to accommodate the lightning arrestor. Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 19 Grounding the Access Point Note Installation Overview This lightning arrestor is part of a lightning arrestor kit. The kit contains a lightning arrestor and a grounding lug. When you install the lightning arrestor, follow the regulations or best practices applicable to lightning protection installation in your local area. Installing the Lightning Arrestor Outdoors If you install the lightning arrestor outdoors, use the supplied ground lug and a heavy wire (#6 solid copper) to connect it to a good earth ground, such as a ground rod. The connection should be as short as possible. 1 2 3 Nut Lockwasher Ground lug 4 5 Unprotected Side (to antenna) Protected side (to wireless device) Cable for the Lightning Arrestor Coaxial cable loses efficiency as the frequency increases, resulting in signal loss. The cable should be kept as short as possible because cable length also determines the amount of signal loss (the longer the run, the greater the loss). Cisco recommends a high-quality, low-loss cable for use with the lightning arrestor. Grounding the Access Point In all installations, after mounting the access point, you must properly ground the unit before connecting power cables. Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 20 Installation Overview Grounding the Access Point This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024 Warning Warning Installation of the equipment must comply with local and national electrical codes. Statement 1074 The access point is shipped with a grounding kit. Figure 11: Access Point Grounding Kit Contents 1 Grounding lug 2 Screws x 2, M4 x 6mm Note The grounding kit also includes the oxide inhibitor, which is contained in a tube. To ground the access point:
Step 1 Use a crimping tool to crimp a 6-AWG ground wire (not included in the grounding kit) to the ground lug. Step 2 Connect the supplied ground lug to the access point ground connection point using the supplied screws. Apply supplied oxide inhibitor between the ground lug and the access point ground connection. Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 21 Powering the Access Point Installation Overview 1 AP ground connection point Step 3 Step 4 Tighten the screws to 20-25 inch-lbs of torque. If necessary, strip the other end of the ground wire and connect it to a reliable earth ground such as a grounding rod or appropriate ground point on a grounded pole. Length of the ground cable should not exceed 1 meter, and 0.5 meter is preferred. Use supplied oxide inhibitor on the grounded interface. Powering the Access Point The AP supports these power sources:
DC power 2448 VDC Power-over-Ethernet (PoE) The AP can be powered via the PoE input from an inline power injector or a suitably powered switch port. Depending on the configuration and regulatory domain, the required power for full operation is 802.3bt or UPOE. For more information, see Power Sources, on page 4. Connecting a Power Injector The AP supports the following power injector:
Table 5: Supporting Power Injectors Power Source Description IW-PWRINJ-60RGDMG=
60W rated outdoor power injector, 5GE The power injector provides DC voltage to the AP over the Ethernet cable and supports a total end-to-end Ethernet cable length of 100 m (328 ft) from the switch to the AP. When an optional power injector powers your AP, follow these steps to complete the installation:
Step 1 Step 2 Before applying PoE to the AP, ensure that the AP is grounded (see Grounding the Access Point, on page 20). Connect a CAT5e or better Ethernet cable from your wired LAN network to the power injector. Warning To reduce the risk of fire, use only No. 24 AWG or larger telecommunication line cord. Statement 1023 Note The installer is responsible for ensuring that powering the AP from this type of power injector is allowed by local and/or national safety and telecommunications equipment standards. Step 3 Ensure that the antennas are connected, and that ground is attached to the AP before you apply power to the AP. Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 22 Installation Overview Connecting a Power Injector Step 4 Step 5 Connect a shielded outdoor-rated Ethernet (CAT5e or better) cable between the power injector and the AP's PoE-in connector. Connect the Ethernet cable to the AP PoE-In port. Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 23 C H A P T E R 4 Troubleshooting Using the Reset Button, on page 25 Checking the Access Point LEDs, on page 25 Using the Reset Button Using the Reset button (see Connectors and Ports, on page 2), you can reset the AP to factory default or clear the AP's internal storage. To reset the AP to the default factory-shipped configuration, perform the following steps:
Step 1 Step 2 Step 3 Press, and continue to press the Reset button on the access point during the AP boot cycle. Press until the AP status LED changes to blinking red. It indicates that the Reset signal has been caught by u-boot. Press the Reset button for more than 20 seconds, but less than 60 seconds, the following will happen:
The AP status LED changes to solid red. All the files in the AP storage directory are cleared. A full factory reset is triggered. The FIPS mode flag is also cleared during the full factory reset of the AP. If the FIPS flag is set, the console access is disabled. Note If you keep the Reset button pressed for more than 60 seconds, the button is assumed as being faulty and no changes are made. Checking the Access Point LEDs The location of the AP status LED is shown in Connectors and Ports, on page 2. Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 25 Checking the Access Point LEDs Troubleshooting Note Regarding LED status colors, it is expected that there will be small variations in color intensity and hue from unit to unit. This is within the normal range of the LED manufacturers specifications and is not a defect. However, the intensity of the LED can be changed through the controller. The AP status LED indicates various conditions and are described in the following table. Table 6: AP LED Signals LED Message Type Color Meaning Boot loader status sequence Blinking Green Boot loader status sequence:
DRAM memory test in progress DRAM memory test OK Board initialization in progress Initializing FLASH file system FLASH memory test OK Initializing Ethernet Ethernet OK Starting AP OS Initialization successful Boot loader warnings Blinking Red Solid Red Blinking Green CAPWAP OS Association status Chirping (short blips) Green Solid Green Configuration recovery is in progress (the Reset button has been pushed for 2 to 3 seconds) There is an Ethernet failure or an image recovery (the Reset button has been pushed for 20-30 seconds) Image recovery is in progress (the Reset button has been released) This status indicates a normal operating condition. The unit is joined to a controller, but no wireless client is associated with it. Normal operating condition with at least one wireless client associated with the unit. Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide Troubleshooting Checking the Access Point LEDs LED Message Type Color Meaning Operating Status Blinking Amber A software upgrade is in progress. Cycling through Green, Red, and Amber Discovery or join process is in progress. Rapidly cycling through Red, Green, Amber, and Off This status indicates that the AP location command has been invoked. Blinking Red Cycling through Red, Green, and Amber This status indicates that an Ethernet link is not operational. This is a general warning of insufficient inline power. Cisco URWB OS Link Quality/SNR Indicator Blinking Green Fade-in Green Fade-in Amber Fade-in Red SNR Excellent (>=25) SNR Good (15<=x<25) SNR Poor (10<=x<15) SNR Unbearable (<10) Operating Status Cycling through Red, Green, and Amber This is a general warning of insufficient inline power. Limbo
(Provisioning) mode: Fallback Limbo
(Provisioning) mode: DHCP Chirping (short blips) Amber In the state of requesting IP address from DHCP server. Amber This status indicates that the IP address is retrieved from DHCP server. Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 27 C H A P T E R 5 Safety Guidelines and Warnings Safety Instructions, on page 29 FCC Safety Compliance Statement, on page 30 Safety Precautions, on page 30 Safety Precautions when Installing Antennas, on page 31 Avoiding Damage to Radios in a Testing Environment, on page 31 Performing Site Surveys, on page 32 Safety Instructions The translated warnings are available in the Translated Safety Warnings for Cisco Catalyst Access Points, which is available on Cisco.com. IMPORTANT SAFETY INSTRUCTIONSThis warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device.SAVE THESE INSTRUCTIONS Statement 1071 Read the installation instructions before using, installing or connecting the system to the power source. Statement 1004 This product relies on the buildings installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than 20A. Statement 1005 Warning Warning Warning Warning Installation of the equipment must comply with local and national electrical codes. Statement 1074 Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 29 FCC Safety Compliance Statement Safety Guidelines and Warnings In order to comply with FCC radio frequency (RF) exposure limits, antennas should be located at a minimum of 15.78 inches (40 cm) or more from the body of all persons. Statement 332 Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040 Warning Warning Caution Ensure to connect the power cord of the power adapter to a socket outlet with an earthing connection. FCC Safety Compliance Statement The FCC, with its action in, has adopted a safety standard for human exposure to RF electromagnetic energy emitted by FCC-certified equipment. When used with approved Cisco antennas, Cisco Catalyst products meet the uncontrolled environmental limits found in IEEE C95.3. Proper operation of this radio device according to the instructions in this publication results in user exposure substantially below the FCC recommended limits. Safety Precautions For safety and to achieve a good installation, please read and follow these safety precautions:
Select your installation site with safety as well as performance in mind. Remember: electric power lines and phone lines look alike. For safety, assume that any overhead line can kill. Call your electric power company. Tell them your plans, and ask them to come to look at your proposed installation Plan your installation carefully and thoroughly before you begin. Successful raising of a mast or tower is mostly a matter of coordination. Each person should be assigned to a specific task and know what to do and when to do it. One person should be in charge of the operation to issue instructions and watch for signs of trouble. When installing the AP or its antennas, remember:
Do not use a metal ladder. Do not work on a wet or windy day. Do dress properlyshoes with rubber soles and heels, rubber gloves, long-sleeved shirt or jacket. Use a rope to lift the AP. If the assembly starts to drop, get away from it and let it fall. If any part of the antenna system comes in contact with a power line, do not touch it or remove it yourself. Call your local power company. They will remove it safely. If an accident should occur, call for qualified emergency help immediately. Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 30 Safety Guidelines and Warnings Safety Precautions when Installing Antennas Safety Precautions when Installing Antennas Danger Do not locate the antenna near overhead power lines or other electric light or power circuits, or where it can come into contact with such circuits. When installing the antenna, take extreme care not to come into contact with such circuits, as they may cause serious injury or death. For proper installation and grounding of the antenna, please refer to national and local codes (e.g. U.S.: NFPA 70, National Electrical Code, Article 810, Canada: Canadian Electrical Code, Section 54). Statement 280 Before you install an antenna, contact your Cisco account representative to explain which mounting method to use for the size and type of antenna that you are about to install Select your installation site with safety, as well as performance, in mind. Remember that electric power lines and phone lines look alike. For your safety, assume that any overhead line can kill you. Contact your electric power company. Tell them your plans and ask them to come look at your proposed installation. Plan your installation carefully and completely before you begin. Each person involved in an installation should be assigned to a specific task and should know what to do and when to do it. One person should be in charge of the operation to issue instructions and watch for signs of trouble. When installing your antenna, follow these guidelines:
Do not use a metal ladder Do not work on a wet or windy day Do dress properlywear shoes with rubber soles and heels, rubber gloves, and a long-sleeved shirt or jacket If the assembly starts to drop, move away from it and let it fall. Because the antenna, mast, cable, and metal guy wires are all excellent conductors of electrical current, even the slightest touch of any of these parts to a power line completes an electrical path through the antenna and the installer. If any part of the antenna system should come in contact with a power line, do not touch it or try to remove it yourself. Call your local power company to have it removed safely. If an accident should occur with the power lines, call for qualified emergency help immediately. Avoiding Damage to Radios in a Testing Environment The radios on outdoor units (bridges) have higher transmit power levels than radios on indoor units (APs). When you test high-power radios in a link, you must avoid exceeding the receiver's maximum receive input level. At levels above the normal operating range, packet error rate (PER) performance is degraded. At even higher levels, the receiver can be permanently damaged. To avoid receiver damage and PER degradation, you can use one of the following techniques:
Separate the omnidirectional antennas by at least 2 ft (0.6 m) to avoid receiver damage or by at least 25 ft (7.6 m) to avoid PER degradation. Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 31 Performing Site Surveys Safety Guidelines and Warnings Note These distances assume free space path loss and are conservative estimates. Required separation distances for damage and performance degradation levels in actual deployments are less if conditions are not non-line-of-sight. Reduce the configured transmit power to the minimum level. Use directional antennas, and keep them away from each other. Cable the radios together using a combination of attenuators, combiners, or splitters to achieve a total attenuation of at least 60 dB. For a radiated testbed, the following equation describes the relationships among transmit power, antenna gain, attenuation, and receiver sensitivity:
txpwr + tx gain + rx gain - [attenuation due to antenna spacing] < max rx input level Where:
txpwr = Radio transmit power level tx gain = transmitter antenna gain rx gain = receiver antenna gain For a conducted test bed, the following equation describes the relationships among transmit power, antenna gain, and receiver sensitivity:
txpwr - [attenuation due to coaxial components] < max rx input level Caution Under no circumstances should you connect the antenna port from one AP to the antenna port of another AP without using an RF attenuator. If you connect antenna ports, you must not exceed the maximum survivable receive level of 0 dBm. Never exceed 0 dBm, or damage to the AP can occur. Using attenuators, combiners, and splitters having a total of at least 60 dB of attenuation ensures that the receiver is not damaged and that PER performance is not degraded. Performing Site Surveys Every network application is a unique installation. Before installing multiple APs, you should perform a site survey to determine the optimum use of networking components and maximize range, coverage, and network performance. Site surveys reveal problems that can be resolved before the network is operational. Because 802.11a/b/g/n/ac/ax operates in an unlicensed spectrum, there may be sources of interference from other 802.11a wireless devices
(especially in multi-tenant buildings) that could degrade your 802.11 signals. A site survey can determine if such interference exists at the time of deployment. Consider the following operating and environmental conditions when performing a site survey:
Data rates: Sensitivity and range are inversely proportional to data bit rates. The maximum radio range is achieved at the lowest workable data rate. A decrease in receiver sensitivity occurs as the radio data increases. Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 32 Safety Guidelines and Warnings Performing Site Surveys Antenna type and placement: Proper antenna configuration is a critical factor in maximizing radio range. As a general rule, range increases in proportion to antenna height. However, do not place the antenna higher than necessary because the extra height also increases potential interference from other unlicensed radio systems and decreases the wireless coverage from the ground. Physical environment: Clear or open areas provide better radio range than closed or filled areas. Obstructions: Physical obstructions such as buildings, trees, or hills can hinder the performance of wireless devices. Avoid locating the devices in a location where there is an obstruction between the sending and receiving antennas. How far is your wireless link?
Has a previous site survey been conducted?
Do you have a clear Fresnel zone between the APs or radio line of sight?
What is the minimum acceptable data rate within the link?
Do you have the correct antenna (if more than one antenna is being offered?) Do you have the proper permits, if required?
Are you following the proper safety procedures and practices?
Have you configured the APs before you go onsite? It is always easier to resolve configurations or device problems first. Do you have the proper tools and equipment to complete your survey?
Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 33 C H A P T E R 6 Declarations of Conformity and Regulatory Information Manufacturers Federal Communication Commission Declaration of Conformity Statement, on page 35 Operation of Cisco Catalyst Access Points in Mxico, on page 36 VCCI Statement for Japan, on page 36 Compliance Statement for Canada, on page 38 European Community, Switzerland, Norway, Iceland, and Liechtenstein, on page 39 United Kingdom Compliance, on page 39 Declaration of Conformity for RF Exposure, on page 40 Declaration of Conformity Statements, on page 42 Manufacturers Federal Communication Commission Declaration of Conformity Statement Access Point Models Certification Number IW9165EB LDKIW9165E Manufacturer:
Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 35 Operation of Cisco Catalyst Access Points in Mxico Declarations of Conformity and Regulatory Information This device complies with Part 15 rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, 2. This device must accept any interference received, including interference that may cause undesired operation. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Caution The Part 15 radio device operates on a non-interference basis with other devices operating at this frequency when using the integrated antennas. Any changes or modification to the product not expressly approved by Cisco could void the users authority to operate this device. Operation of Cisco Catalyst Access Points in Mxico Declaracin para Mxico La operacin de este equipo est sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada. VCCI Statement for Japan Statement 191Voluntary Control Council for Interference (VCCI) Class A Warning for Japan Warning This is a Class A product based on the standard of the VCCI Council. If this equipment is used in a domestic environment, radio interference may occur, in which case, you may be required to take corrective actions. Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 36 Declarations of Conformity and Regulatory Information 191 VCCI A 191 VCCI A VCCI-A Guidelines for Operating Cisco Catalyst Access Points in Japan This section provides guidelines for avoiding interference when operating Cisco Catalyst access points in Japan. These guidelines are provided in both Japanese and English. English Translation This equipment operates in the same frequency bandwidth as industrial, scientific, and medical devices such as microwave ovens and mobile object identification (RF-ID) systems (licensed premises radio stations and unlicensed specified low-power radio stations) used in factory production lines. 1. Before using this equipment, make sure that no premises radio stations or specified low-power radio stations of RF-ID are used in the vicinity. 2. If this equipment causes RF interference to a premises radio station of RF-ID, promptly change the frequency or stop using the device; contact the number below and ask for recommendations on avoiding radio interference, such as setting partitions. 3. If this equipment causes RF interference to a specified low-power radio station of RF-ID, contact the number below. Contact Number: 03-6434-6500 Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 37 Compliance Statement for Canada Declarations of Conformity and Regulatory Information Compliance Statement for Canada This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. This radio transmitter has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.Le prsent metteur radio a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal et l'impdance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. Operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.La bande 5 150-5 250 MHz est rservs uniquement pour une utilisation l'intrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux. Users are advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.Les utilisateurs tes aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., qu'ils ont la priorit) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. Industry Canada Access Point Models Certification Number IW9165E-A IC:2461A-IW9165E IC Radiation Exposure Statement This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 38 Declarations of Conformity and Regulatory Information European Community, Switzerland, Norway, Iceland, and Liechtenstein Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. European Community, Switzerland, Norway, Iceland, and Liechtenstein Access Point Models:
IW9165E-E The product carries the CE Mark:
The device is restricted to indoor use only when operating between 5150 MHz and 5350 MHz, 5925 MHz and 6425 MHz frequency range. This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm (7.87 inches) between the radiator
& your body. Note This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation. For more details, contact Cisco Corporate Compliance. The frequency and the maximum transmitted power in EU are listed below:
2402-2480MHz (LE): 9.92 dBm 5180-5240MHz: 22.96 dBm 5260-5320MHz: 22.98 dBm 5500-5700: 29.99 dBm Norway(NO), Iceland(IS), Lichtenstein(LI), Turkey(TR), Switzerland(CH) United Kingdom Compliance Access Point Models:
IW9165E-ROW Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 39 Declaration of Conformity for RF Exposure Declarations of Conformity and Regulatory Information The device is restricted to indoor use only when operating between 5150 MHz and 5350 MHz, 5925 MHz and 6425 MHz frequency range. This equipment should be installed and operated with minimum distance 20 cm (7.87 inches) between the radiator & your body. The frequency and the maximum transmitted power in UK are listed below:
2402-2480MHz (LE): 9.92 dBm 5180-5240MHz: 22.96 dBm 5260-5320MHz: 22.98 dBm 5500-5700: 29.99 dBm Declaration of Conformity for RF Exposure This section contains information on compliance with guidelines related to RF exposure. Generic Discussion on RF Exposure The Cisco products are designed to comply with the following national and international standards on Human Exposure to Radio Frequencies:
US 47 Code of Federal Regulations Part 2 Subpart J American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers / IEEE C 95.3 International Commission on Non Ionizing Radiation Protection (ICNIRP) 98 Ministry of Health (Canada) Safety Code 6. Limits on Human Exposure to Radio Frequency Fields in the range from 3kHz to 300 GHz Australia Radiation Protection Standard To ensure compliance with various national and international Electromagnetic Field (EMF) standards, the system should only be operated with Cisco approved antennas and accessories. This Device Meets International Guidelines for Exposure to Radio Waves The IW9165E device includes a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves (radio frequency electromagnetic fields) recommended by international guidelines. The guidelines were developed by an independent scientific organization (ICNIRP) and include a substantial safety margin designed to ensure the safety of all persons, regardless of age and health. As such the systems are designed to be operated as to avoid contact with the antennas by the end user. It is recommended to set the system in a location where the antennas can remain at least a minimum distance as specified from the user in accordance to the regulatory guidelines which are designed to reduce the overall exposure of the user or operator. RF Exposure Distance 20 cm Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 40 Declarations of Conformity and Regulatory Information This Device Meets FCC Guidelines for Exposure to Radio Waves The World Health Organization has stated that present scientific information does not indicate the need for any special precautions for the use of wireless devices. They recommend that if you are interested in further reducing your exposure then you can easily do so by reorienting antennas away from the user or placing he antennas at a greater separation distance then recommended. This Device Meets FCC Guidelines for Exposure to Radio Waves The IW9165E device includes a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves (radio frequency electromagnetic fields) as referenced in FCC Part 2.1091. The guidelines are based on IEEE ANSI C 95.3 and KDB 447498 and include a substantial safety margin designed to ensure the safety of all persons, regardless of age and health. As such the systems are designed to be operated as to avoid contact with the antennas by the end user. It is recommended to set the system in a location where the antennas can remain at least a minimum distance as specified from the user in accordance to the regulatory guidelines which are designed to reduce the overall exposure of the user or operator. The device has been tested and found compliant with the applicable regulations as part of the radio certification process. RF Exposure Distance 40 cm The US Food and Drug Administration has stated that present scientific information does not indicate the need for any special precautions for the use of wireless devices. The FCC recommends that if you are interested in further reducing your exposure then you can easily do so by reorienting antennas away from the user or placing the antennas at a greater separation distance then recommended or lowering the transmitter power output. This Device Meets the Industry Canada Guidelines for Exposure to Radio Waves The IW9165E device includes a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves (radio frequency electromagnetic fields) as referenced in Health Canada Safety Code 6. The guidelines include a substantial safety margin designed into the limit to ensure the safety of all persons, regardless of age and health. As such the systems are designed to be operated as to avoid contact with the antennas by the end user. It is recommended to set the system in a location where the antennas can remain at least a minimum distance as specified from the user in accordance to the regulatory guidelines which are designed to reduce the overall exposure of the user or operator. RF Exposure Distance 20 cm Health Canada states that present scientific information does not indicate the need for any special precautions for the use of wireless devices. They recommend that if you are interested in further reducing your exposure you can easily do so by reorienting antennas away from the user, placing the antennas at a greater separation distance than recommended, or lowering the transmitter power output. Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 41 Cet appareil est conforme aux directives internationales en matire d'exposition aux frquences radiolectriques Declarations of Conformity and Regulatory Information Cet appareil est conforme aux directives internationales en matire d'exposition aux frquences radiolectriques Cet appareil de la gamme IW9165E comprend un metteur-rcepteur radio. Il a t conu de manire respecter les limites en matire d'exposition aux frquences radiolectriques (champs lectromagntiques de frquence radio), recommandes dans le code de scurit 6 de Sant Canada. Ces directives intgrent une marge de scurit importante destine assurer la scurit de tous, indpendamment de l'ge et de la sant. Par consquent, les systmes sont conus pour tre exploits en vitant que l'utilisateur n'entre en contact avec les antennes. Il est recommand de poser le systme l o les antennes sont une distance minimale telle que prcise par l'utilisateur conformment aux directives rglementaires qui sont conues pour rduire l'exposition gnrale de l'utilisateur ou de l'oprateur. Distance d'exposition RF 20 cm Sant Canada affirme que la littrature scientifique actuelle n'indique pas qu'il faille prendre des prcautions particulires lors de l'utilisation d'un appareil sans fil. Si vous voulez rduire votre exposition encore davantage, selon l'agence, vous pouvez facilement le faire en rorientant les antennes afin qu'elles soient diriges l'cart de l'utilisateur, en les plaant une distance d'loignement suprieure celle recommande ou en rduisant la puissance de sortie de l'metteur. Additional Information on RF Exposure You can find additional information on the subject at the following links:
Cisco Systems Spread Spectrum Radios and RF Safety white paper at this URL:
http://www.cisco.com/warp/public/cc/pd/witc/ao340ap/prodlit/rfhr_wi.htm FCC Bulletin 56: Questions and Answers about Biological Effects and Potential Hazards of Radio Frequency Electromagnetic Fields FCC Bulletin 65: Evaluating Compliance with the FCC guidelines for Human Exposure to Radio Frequency Electromagnetic Fields You can obtain additional information from the following organizations:
World Health Organization Internal Commission on Non-Ionizing Radiation Protection at this URL:
www.who.int/emf United Kingdom, National Radiological Protection Board at this URL: www.nrpb.org.uk Cellular Telecommunications Association at this URL: www.wow-com.com The Mobile Manufacturers Forum at this URL: www.mmfai.org Declaration of Conformity Statements All the Declaration of Conformity statements related to this product can be found at the following location:
https://pas.cisco.com/pdtcnc/#/
Cisco Catalyst IW9165E Rugged Access Point and Wireless Client Hardware Installation Guide 42