The Cisco Meraki GR60 is a dual-band enterprise class 802.11ac cloud-managed access point Package Contents The GR60 package contains the following:
GR60 Cloud-Managed Access Point Mount cradle including built-in level tool Mount Kit o Wall screws and wall screw anchors Understanding the GR60 Your Meraki GR60 has the following features:
The mount cradle has the following features:
Ethernet Ports The GR60 features a Gigabit Ethernet RJ45 port that accepts 802.3at and 802.3af power
(labeled Eth0, PoE). This port should be used for uplink to your WAN connection. Power Source Options The GR60 access point can be powered using either the Meraki AC Adapter, PoE Injector
(both sold separately), or a third-party PoE switch. Factory Reset Button If the button is pressed and held for at least ve seconds and then released, the GR60 will reboot and be restored to its original factory settings by deleting all conguration information stored on the unit. LED Indicators and Run Dark Mode Your GR60 is equipped with a multi-color LED light on the front of the unit to convey information about system functionality and performance:
Orange - AP is booting (permanent Orange suggests hardware issue) Rainbow - AP is initializing/scanning Blinking Blue - AP is upgrading Green - AP in Gateway mode with no clients Blue - AP in Gateway mode with clients Blinking Orange - AP can't find uplink The GR60 may be operated in Run Dark mode for additional security and to reduce the visibility of the access point. In this mode, the LED will not be illuminated. This mode may be enabled through Meraki dashboard. Pre-Install Preparation You should complete the following steps before going on-site to perform an installation. Congure Your Network in Dashboard The following is a brief overview only of the steps required to add an GR60 to your network. For detailed instructions about creating, conguring and managing Meraki wireless networks, refer to the online documentation (documentation.meraki.com). 1. Login to http://dashboard.meraki.com. If this is your rst time, create a new account. 2. Find the network to which you plan to add your APs or create a new network. 3. Add your APs to your network. You will need your Meraki order number (found on your invoice) or the serial number of each AP, which looks like Qxxx-xxxx-xxxx, and is found on the bottom of the unit. You will also need your Enterprise license key, which you should have received via email. 4. Go to the map / oor plan view and place each AP on the map by clicking and dragging it to the location where you plan to mount it. Check and Upgrade Firmware To ensure your GR60 performs optimally immediately following installation, it is recommended that you facilitate a rmware upgrade prior to mounting your GR60. 1. Attach your GR60 to power and a wired Internet connection. See the "Power the GR60" section for details. 2. The GR60 will turn on and the LED will glow solid orange. If the unit does not require a rmware upgrade, the LED will turn either green (no clients associated) or blue
(clients associated) within thirty seconds.
* If the unit requires an upgrade, the LED will begin blinking orange until the upgrade is complete, at which point the LED will turn solid green or blue. You should allow at least a few minutes for the rmware upgrade to complete, depending on the speed of your internet connection. Check and Congure Firewall Settings If a rewall is in place, it must allow outgoing connections on particular ports to particular IP addresses. The most current list of outbound ports and IP addresses for your particular organization can be found here. Assigning IP Addresses to GR60s All gateway GR60s (GR60s with Ethernet connections to the LAN) must be assigned routable IP addresses. These IP addresses can be dynamically assigned via DHCP or statically assigned. Dynamic Assignment When using DHCP, the DHCP server should be congured to assign a static IP address for each MAC address belonging to a Meraki AP. Other features of the wireless network, such as 802.1X authentication, may rely on the property that the APs have static IP addresses. Static Assignment Static IPs are assigned using the local web server on each AP. The following procedure describes how to set the static IP:
1. Using a client machine (e.g., a laptop), connect to the AP wirelessly (by associating to any SSID broadcast by the AP) or over a wired connection. 2. If using a wired connection, connect the client machine to the GR60 either through a PoE switch or a PoE Injector. If using a PoE switch, plug an Ethernet cable into the GR60s Ethernet jack, and the other end into a PoE switch. Then connect the client machine over Ethernet cable to the PoE switch. If using a PoE Injector, connect the GR60 to the PoE port of the Injector, and the client machine to the LAN port. 3. Using a web browser on the client machine, access the APs built-in web server by browsing to http://my.meraki.com. Alternatively, browse to http://10.128.128.128. 4. Click on the Uplink Conguration tab. Log in. The default login is the serial number
(e.g. Qxxx-xxxx-xxxx), with no password (e.g., Q2DD-551C-ZYW3). 5. Congure the static IP address, net mask, gateway IP address and DNS servers that this AP will use on its wired connection. 6. If necessary, reconnect the AP to the LAN. Static IP via DHCP Reservations Instead of associating to each Meraki AP individually to congure static IP addresses, an administrator can assign static IP addresses on the upstream DHCP server. Through DHCP reservations, IP addresses are reserved for the MAC addresses of the Meraki APs. Please consult the documentation for the DHCP server to congure DHCP reservations. Collect Tools You will need the following tools to perform an installation:
Collect Additional Hardware for Installation You will need the following hardware to perform an installation:
Installation Instructions Choose Your Mounting Location A good mounting location is important to getting the best performance out of your GR60 access point. Keep the following in mind:
1. The device should have unobstructed line of sight to most coverage areas. For example, if installing in an ofce lled with workspaces divided by mid-height cubicle walls, installing on the ceiling or high on a wall would be ideal. 2. Power over Ethernet supports a maximum cable length of 300 ft (100 m). 3. If being used in a mesh deployment, the GR60 should have line of sight to at least two other Meraki devices. A Cisco Partner can help ensure that your AP placement is ideal. Install the GR60 For most mounting scenarios, the GR60 mount cradle provides a quick, simple, and exible means of mounting your device. The installation should be done in two steps. First, install the mount cradle to your selected location. Then, attach the GR60 to the mount cradle Mount the GR60 Attach the GR60 to the Mount Cradle The GR60 attaches to the mount cradle with two tabs on the cradle that insert into the GR60, and is secured to the cradle using one screw. To attach the GR60 to the mount cradle properly, line up the top edge of the AP with the top tab of the mount cradle. Since the cradle is already mounted to the wall, guide the GR60 towards the top tab and insert the top tab into the GR60s slot. Then adjust the GR60 to guide the GR60s bottom slot into the cradles bottom tab until it clicks into place. Once in place, the GR60 should be secured to the cradle by using one of the included screws in the cradles bottom tab. To release the GR60 from the mount cradle, first remove the security screw that secures the GR60 to the cradles bottom tab. While holding the GR60 with one hand, press the cradles bottom tab upwards, releasing the GR60 from the bottom of the cradle. Then remove the GR60 from the cradles top tab. Power the GR60 If mounting to an electrical junction box, feed the Ethernet cable through the cable access hole in the mount cradle. If mounting to a wall or ceiling, the Ethernet cable will feed from behind the GR60. The "Power Source Options" section of this document lists the different powering options and their unique characteristics. Verify Device Functionality and Test Network Coverage 1. Check LEDs a. The Power LED should be solid green (or blue, if clients are connected). If it is ashing blue, the rmware is automatically upgrading and the LED should turn green when the upgrade is completed (normally within a few minutes). See the "LED Indicators" section for more details. b. Note: Your GR60 must have an active route to the Internet to check and upgrade its rmware. 2. Verify access point connectivity a. Use any 802.11 client device to connect to the GR60 and verify proper connectivity using the clients web browser. 3. Check network coverage 4. Conrm that you have good signal strength throughout your coverage area. You can use the signal strength meter on a laptop, smart phone, or other wireless device. Troubleshooting Reference the MR Product Page for additional information and troubleshooting tips. Regulatory This equipment is for indoor use only and the PoE device is considered unlikely to connect to an Ethernet network with outside plant routing, including campus environments. FCC Compliance Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution Any changes or modifications no expressly approved by Meraki could void the users authority to operate this equipment. This Transmitter must not be co-located or operation in conjunction with any other antenna or transmitter. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IEEE 802.11b or 802.11g operation of this product in the USA is firmware-limited to channels 1 through 11. If the device is going to be operated in the 5.15 - 5.25 frequency range, then it is restricted to indoor environment only. This device meets all other requirements specified in Part 15E, Section 15.407 of the FCC Rules. Industry Canada Statement This device complies with RSS-247 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme la norme CNR-247 dIndustrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. Industry Canada Caution
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
(ii) high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-
5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Avertissement:
(i) les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;
(ii) De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., quils ont la priorit) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. Industry Canada Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. Dclaration dexposition aux radiations Cet quipement est conforme aux limites dexposition aux rayonnements IC tablies pour un environnement non con trl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.s NCC Compliance Statement MPE1mW/cm2 20 cm 1. 2.