MR76 Installation Guide The Cisco Meraki MR76 are dual-band enterprise class 802.11ax cloud-managed access points. Designed for highest capacity and highest density, the MR76 meets the needs of the most demanding environments. The access point also includes a third radio dedicated to optimizing the RF environment and securing the airwaves. About this Guide This guide provides instruction on how to install and configure your MR76 access points. This guide also provides mounting instructions and limited troubleshooting procedures. For more wireless installation guides, refer to the wireless installation guides section on our documentation website. Product Overview Physical Specifications MR76 Interfaces 1x 10/100/1000 BASE-T Ethernet (RJ45) Four external N-type female antenna connectors Power Power over Ethernet: 37 - 57 V (802.3af compatible) Power consumption: 15W max (802.3af) Power over Ethernet injector sold separately Note: Actual power consumption may vary depending on the AP usage. Environment Operating temperature: -40 F to 131 F (-40 C to 55 C) Humidity: 5 to 95% non-condensing IP67 Environmental rating Physical Security 1 Two security screws Package Contents The MR76 package contains the following:
MR76 Cloud-Managed Access Point Mount cradle Wall screws Wall screw anchors Grounding screws Mounting straps Product View and Physical Features Your Meraki MR76 has the following physical features:
2 The mount cradle has the following physical features:
3 4 LED indicator Your MR76 is equipped with a multi-color LED light on the bottom edge of the unit to convey information about system functionality and performance:
Orange - AP is booting (permanent Orange suggests hardware issue) Rainbow - AP is initializing/scanning Blinking Blue - AP is upgrading Green - AP in Gateway mode with no clients Blue - AP in Gateway mode with clients Blinking Orange - AP can't find uplink The MR76 may be operated in Run Dark mode for additional security and to reduce the visibility of the access point. In this mode, the LED will not be illuminated. This mode may be enabled through the Meraki dashboard. Ethernet Port The MR76 features one Ethernet ports:
This accepts 802.3af power and should be used as the primary uplink to your LAN/WAN. N-Type antenna attachment ports (4x) 2x N-Type antenna ports are located at the top of the MR76 and 2x are located at the bottom of the MR76. The 4 antenna ports are connected to 2.4 GHz and 5 GHz client serving radios respectively. Please see the markings on the AP to verify 2.4GHz and 5GHz ports. In order to ensure the highest performance, ensure antennas connected to the 4 ports have overlapping coverage areas. Mount plate attachment slots The mounting slots located on the rear shell of the MR76 marry to the 4 mounting posts on the mounting plate, securely fastening the MR76 to the mounting plate. Factory reset button The factory reset button is located in a small pin-sized hole just above the PoE Ethernet port of the MR76. If the button is pressed and held for at least ve seconds and then released, the MR76 will reboot and be restored to its original factory settings by deleting all configuration information stored on the unit. The Vent The vent allows pressure equalization between the interior and the environment. This prevents internal condensation and maintains a waterproof seal. 5 Understanding the MR76 mount plate The mount plate is unique to the MR76. Previous outdoor AP mount plates are not compatible with the MR76. The mount cradle has the following features:
Mounting posts (4x) The mounting slots located in the middle of the mounting plate marry the MR76 to the mounting plate. Mounting holes (4x) The mounting holes located on the 4 outermost corners of the mounting plate allow secure installation of the mounting plate to a surface such as a wall. Vertical orientation mounting strap slots (2x) The vertical orientation mounting strap slots located in the middle of the mounting plate secure the mounting plate to a vertical pole using the included mounting straps. Horizontal orientation mounting strap slots (2x) The horizontal orientation mounting strap slots located in the middle of the mounting plate secure the mounting plate to a horizontal pole using the included mounting straps. Release tab The release tab located at the bottom of the mounting plate. It locks the movement of the AP once attached. Mount plate attachment screw The mount plate attachment screw is located at the bottom of the mounting plate. It securely attaches the AP to the mounting plate. Mount plate grounding post The mount plate grounding post located on the left side of the mounting plate. Using the included grounding strap, the ground post allows you to ground the unit. Safety and Warnings These operations are to be taken with respect to all local laws. Please take the following into consideration for safe operation:
Power off the unit before you begin. Read the installation instructions before connecting the system to the power source. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Read the wall-mounting instructions carefully before beginning installation. Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system. This product relies on the buildings installation for short-circuit (overcurrent) protection. Ensure that the protective 6 device is rated not greater than: 15 A, 125 Vac, or 10A, 240 Vac. Please only power the device with the provided power cables or standard PoE to ensure regulatory compliance. Pre-Install Preparation You should complete the following steps before going on-site to perform an installation. Congure Your Network in Dashboard The following is a brief overview only of the steps required to add an MR76 to your network. For detailed instructions about creating, conguring and managing Meraki wireless networks, refer to the online documentation (documentation.meraki.com/mr). 1. Login to http://dashboard.meraki.com. If this is your rst time, create a new account. 2. Find the network to which you plan to add your APs or create a new network. 3. Add your APs to your network. You will need your Meraki order number (found on your invoice) or the serial number of each AP, which looks like Qxxx-xxxx-xxxx, and is found on the bottom of the unit. You will also need your Enterprise license key, which you should have received via email. 4. Go to the map / oor plan view and place each AP on the map by clicking and dragging it to the location where you plan to mount it. Check and Upgrade Firmware To ensure your MR76 performs optimally immediately following installation, it is recommended that you facilitate a rmware upgrade prior to mounting your MR76. 1. Attach your MR76 to PoE enabled wired Internet connection. See the "Power the MR76" section for details. 2. The MR76 will turn on and the LED will glow solid orange. If the unit does not require a rmware upgrade, the LED will turn either green (no clients associated) or blue (clients associated) within thirty seconds.
* If the unit requires an upgrade, the LED will begin blinking blue until the upgrade is complete, at which point the LED will turn solid green or blue. You should allow at least a few minutes for the rmware upgrade to complete, depending on the speed of your internet connection. Check and Congure Firewall Settings If a rewall is in place, it must allow outgoing connections on particular ports to particular IP addresses. The most current list of outbound ports and IP addresses for your particular organization can be found here. Assigning IP Addresses to MR76s All gateway MR76s (MR76s with Ethernet connections to the LAN) must be assigned routable IP addresses. These IP addresses can be dynamically assigned via DHCP or statically assigned. Dynamic Assignment (Recommended) When using DHCP, the DHCP server should be congured to assign a static IP address for each MAC address belonging to a Meraki AP. Other features of the wireless network, such as 802.1X authentication, may rely on the property that the APs have static IP addresses. 7 Static Assignment Static IPs are assigned using the local web server on each AP. The following procedure describes how to set the static IP:
1. Using a client machine (e.g., a laptop), connect to the AP wirelessly (by associating to any SSID broadcast by the AP) or over a wired connection. 2. If using a wired connection, connect the client machine to the MR76 either through a PoE switch or a PoE Injector. If using a PoE switch, plug an Ethernet cable into the MR76s Ethernet jack, and the other end into a PoE switch. Then connect the client machine over Ethernet cable to the PoE switch. If using a PoE Injector, connect the MR76 to the PoE port of the Injector, and the client machine to the LAN port. 3. Using a web browser on the client machine, access the APs built-in web server by browsing to http://my.meraki.com. Alternatively, browse to http://10.128.128.128. 4. Click on the Uplink Conguration tab. Log in. The default login is the serial number (e.g. Qxxx-xxxx-xxxx), with no password (e.g., Q2DD-551C-ZYW3). 5. Congure the static IP address, net mask, gateway IP address and DNS servers that this AP will use on its wired connection. 6. If necessary, reconnect the AP to the LAN. Static IP via DHCP Reservations Instead of associating to each Meraki AP individually to congure static IP addresses, an administrator can assign static IP addresses on the upstream DHCP server. Through DHCP reservations, IP addresses are reserved for the MAC addresses of the Meraki APs. Please consult the documentation for the DHCP server to congure DHCP reservations. Collect Tools You will need the following tools to perform an installation:
8 Collect Additional Hardware for Installation You will need the following tools to perform an installation:
Network cables with RJ45 connectors long enough for your particular mounting location 802.3af PoE power source (either PoE switch or Meraki PoE Injector) Connection to the internet (if you are setting up your MR76 as a gateway to the internet) Appropriately sized metal straps (if mounting to a pole larger than 3.9 in diameter) Specialized mounting hardware if mounting to surface other than wood, stucco or stone Installation Instructions Warning: Due to the heat dissipation in the back of APs during normal operation, please do not stack powered on APs on top of each other during pre-installation to avoid heat damage. 9 Choose Your Mounting Location A good mounting location is important to getting the best performance out of your MR76 access point. Keep the following in mind:
1. The device should have unobstructed line of sight to most coverage areas. 2. Power over Ethernet supports a maximum cable length of 300 ft (100 m). 3. If being used in a mesh deployment, the MR76 should have line of sight to at least two other Meraki devices. 4. The antennas should be as unobstructed as possible. Make sure that there is clearance around the MR76 for installation of all of your chosen antennas. Install the MR76 For most mounting scenarios, the MR76 mount cradle provides a quick, simple, and exible means of mounting your device. The installation should be done in two steps. First, install the mount cradle to your selected location. Then, attach the MR76 to the mount cradle. Remove the Mount Plate from the Access Point Before installing the mount plate, you must remove it from the back of the access point. 1. Unscrew the mount plate attachment screw. 2. Lift the mount plate release tab upwards. 3. While holding the mount plate release tab up, slide the mount plate off the access point in the direction shown below. Attach the mount cradle The MR76 mount plate can be used to install your access point in a wide range of scenarios. Wall or Solid Ceiling Mount Using mount cradle Using included wall anchors and screws, attach the mount plate to your mounting wall or ceiling. 10 It is recommended that the MR76 be mounted to a wall or solid ceiling using the mount plate for physical security reasons. Pole Mount Using Mount Plate Use the included mounting straps to mount the AP to a pole less than 3.9 in diameter. Thread the mounting straps through the mounting strap slots to secure the mount plate in a horizontal or vertical orientation. 11 Attaching the antennas to the AP 12 Attaching the AP to the mounting bracket 13 Attach Grounding Strap Connect one end of grounding strap to grounding post with included screw and washer. Securely attach the other end nearby metal structure. 14 Antennas Choose the antenna based on the install location and designed area of coverage. The datasheet includes a list of certified antennas. 3rd party antennas may be used but it is the responsibility of the end customer/partner to ensure operation is within regulatory compliance. 15 Reminder: Since the MR76 requires one antenna for each band please ensure that the antennas are aimed in the same coverage area. Antenna selection Meraki offers a number of antenna options for the MR76 access point. The MR76 features dual band antenna ports thus dual band antennas should be paired with the AP. Below is a highlight of the different antenna types and their applications. It is always best practice to consult with a Cisco SE or Partner in to select the best antenna for the unique design. Omni Directional Omni directional antennas are best for pole mounts applications and for mesh networks. Use omni directional antennas when designing to cover 360 degrees around the Access Point. Sector Antenna Sector antennas are ideal for building mounts as they target the signal away from the interior spaces of the building and focus the energy to the larger outdoor space. This antenna is ideal for exterior building use but may also be used for some mesh network designs. Patch Antenna Patch antennas are ideal for Access points mounted on a high ceiling and is intended to cover a large space. This antenna is ideal for warehouses. Stadium Patch Antenna A stadium patch antenna is ideal for a high density AP deign with expected high user per sqft. Examples of this are in stadiums where 1 AP is designed to cover a section and a event center where there is high user per sqft. Please select the right antenna in Dashboard when adding the MR76 to a network. Maximum TX power will depend on the antenna selection made in Dashboard. Aim Antennas If you are using directional antennas, aim them appropriately to ensure optimal performance for your specific network topography. Omnidirectional antennas perform best in a mesh network when oriented vertically. Patch and sector antennas should be angled in the direction of the desired coverage area. Attach Antennas Remove protective plastic covers from all four N-type RF connectors. Attach appropriate antennas (and protective boots if included). Power the MR76 1. Route the Ethernet cable from the PoE Injector OUT port or from a PoE enabled switch to the MR76. 2. Install a Cable Gland on the MR76 end of the cable. 16 17 3. Plug the Ethernet cable into the Ethernet port of the Meraki MR76. a. Connect the cable to the Ethernet port on the MR76. b. Screw the gland body into the threaded hole of the port. Use an adjustable wrench to make sure the gland body is fully seated in the hole. c. Insert the split ring gasket into the gland body. d. Screw the cap tightly onto the gland. You may need a wrench to fully tighten the cap, but take care not to damage the cable in the process. Powering the MR76 with the Meraki 802.3at Power over Ethernet Injector (sold separately) 1. Plug the power cord into the PoE Injector and the other end into wall power. 2. Plug an Ethernet cable that is connected to an active Ethernet connection into the IN port on the injector. 3. Route Ethernet cable from the OUT port on the injector to the PoE labled port in the cable bay of the MR76. MR76 requires only 802.3af power to operate in normal mode. Verify Device Functionality and Test Network Coverage 1. Check LEDs a. The Power LED should be solid green (or blue, if clients are connected). If it is ashing blue, the rmware is automatically upgrading and the LED should turn green when the upgrade is completed (normally within a few minutes). See the "LED Indicators" section for more details. b. Note: Your MR76 must have an active route to the Internet to check and upgrade its rmware. 2. Verify access point connectivity a. Use any 802.11 client device to connect to the MR76 and verify proper connectivity using the clients web browser. 3. Check network coverage 4. Conrm that you have good signal strength throughout your coverage area. You can use the signal strength meter on a laptop, smart phone, or other wireless device. Troubleshooting Reference the MR Product Page for additional information and troubleshooting tips. Support and Additional Information If issues are encountered with device installation or additional help is required, contact Meraki Support by logging in to dashboard.meraki.com and opening a case by visiting the Get Help section. 18 The equipment is intended for industrial or other commercial activities. The equipment is used in areas without exposure to harmful and dangerous production factors, unless otherwise specified in the operational documentation and/or on the equipment labeling. The equipment is not for domestic use. The equipment is intended for operation without the constant presence of maintenance personnel. The equipment is subject to installation and maintenance by specialists with the appropriate qualifications, sufficient specialized knowledge, and skills. Rules and conditions for the sale of equipment are determined by the terms of contracts concluded by Cisco or authorized Cisco partners with equipment buyers. Disposal of a technical device at the end of its service life should be carried out in accordance with the requirements of all state regulations and laws. Do not throw in the device with household waste. The technical equipment is subject to storage and disposal in accordance with the organization's disposal procedure. The equipment should be stored in its original packaging in a room protected from atmospheric precipitation. The permissible temperature and humidity ranges during storage are specified in the Operation (Installation) Manual. Transportation of equipment should be carried out in the original packaging in covered vehicles by any means of transport. The temperature and humidity during transportation must comply with the permissible established ranges of temperature and humidity during storage (in the off state) specified in the Operation Manual (Installation). For additional information on Meraki hardware and for other installation guides, please refer to documentation.meraki.com. (edited) Regulatory Information Europe EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC:
Radio: EN 300 328, EN 301 893 EMC: EN 301 489-1, EN 301 489-17 Safety: EN 60950-1 Exposure: EN 505385 Emissions: EN 55022, EN 61000-3-2, EN 61000-3-3 Immunity: EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN 61000-4-6, EN 61000-4-11 See meraki.cisco.com/compliance This device is a 2.4 GHz and 5 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries with the following restrictions:
Frequency Band (MHz) Max Power Level (EIRP) (mW) Indoor ONLY Indoor and Outdoor 2400 - 2483.5 100 X 19 Frequency Band (MHz) Max Power Level (EIRP) (mW) Indoor ONLY Indoor and Outdoor 200 1000 X X 5150 - 5350 5470 - 5725 Denmark The band 5150-5350 MHz is also allowed for outdoor usage. I Danmark m frekvensbndet 5150-5350 ogs anvendes udendrs. Italy This product meets the National Radio Interface and the requirements specified in the National Frequency allocation Table for Italy. Unless this wireless LAN product is operating within the boundaries of the owners property, its use requires a general authorization. Questo prodotto conforme alla specifiche di Interfaccia Radio Nazionali e rispetta il Piano Nazionale di ripartizione delle frequenze in Italia. Se non viene installato all interno del proprio fondo, lutilizzo di prodotti Wireless LAN richiede una Autorizzazione Generale. Latvia The outdoor usage of the 2.4 GHz band requires an authorization from the Electronic Communications Office. 2.4 GHz frekvenu joslas izmantoanai rpus telpm nepiecieama at auja no Elektronisko sakaru direkcijas.
(Bulgarian):
Cisco Systems, Inc. , 1999/5/EC. esky (Czech):
Cisco Systems, Inc. tmto prohlauje, e tento wireless device je ve shod se zkladnmi poadavky a dalmi pslunm ustanovenmi smrnice. Dansk (Danish):
Undertegnede Cisco Systems, Inc. erklrer herved, at flgende udstyr wireless device overholder de vsentlige krav og vrige relevante krav i direktiv 1999/5/
EF. Deutsch (German):
Hiermit erklrt Cisco Systems, Inc. dass sich das Gert wireless device in bereinstimmung mit den grundlegenden Anforderungen und den brigen einschlgigen Bestimmungen der Richtlinie 1999/5/EG befi ndet. Eesti (Estonian):
Kesolevaga kinnitab Cisco Systems, Inc. seadme seadme wireless device vastavust direktiivi 1999/5/E phinuetele ja nimetatud direktiivist tulenevatele. 20 English:
Hereby, Cisco Systems, Inc. declares that this wireless device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/
EC. Espaol (Spanish):
Por medio de la presente Cisco Systems, Inc. declara que el wireless device cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
(Greek):
Cisco Systems, Inc. wireless device 1999/5/. Franais (French):
Par la prsente Cisco Systems, Inc. dclare que lappareil wireless device est conforme aux exigencies essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. celenska (Icelandic):
Hr, Cisco Systems, Inc. yfir a rlaus tki er samrmi vi grunnkrfur og nnur vieigandi kvi tilskipunar 1999/5/EB. Italiano (Italian):
Con la presente Cisco Systems, Inc. dichiara che questo wireless device conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviski (Latvian):
Ar o Cisco Systems, Inc. deklar, ka wireless device atbilst Direktvas 1999/5/EK btiskajm prasbm un citiem ar to saisttajiem noteikumiem. Lietuvi (Lithuanian):
iuo Cisco Systems, Inc. deklaruoja, kad is wireless device atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Nederland (Dutch):
Hierbij verklaart Cisco Systems, Inc. dat het toestel wireless device in overeenstemming is met de essentile eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Malti (Maltese):
Hawnhekk, Cisco Systems, Inc. jiddikjara li dan wireless device jikkonforma mal-tigijiet essenzjali u ma provvedimenti orajn relevanti li hemm fi d-Dirrettiva 1999/5/EC. Magyar (Hungarian):
Alulrott, Cisco Systems, Inc. nyilatkozom, hogy a wireless device megfelel a vonatkoz alapvet kvetelmnyeknek s az 1999/5/EC irnyelv egyb 21 elrsainak. Norsk (Norwegian):
Erklrer herved Cisco Systems, Inc. at denne trdlse enheten er i samsvar med de grunnleggende krav og vrige relevante krav i direktiv 1999/5/EF. Polski (Polish):
Niniejszym Cisco Systems, Inc. deklaruje e to urzdzenie bezprzewodowe jest zgodne z zasadniczymi wymaganiami oraz pozostalymi stosowynmi postanowieniami Dyrektywy 199/5/WE. Portugus (Portuguese):
Cisco Systems, Inc. declara que este wireless device est conforme com os requisitos essenciais e outras disposies da Directiva 1999/5/CE. Romn (Romanian):
Prin prezenta, Cisco Systems, Inc. declar c acest dispozitiv fr fir este n conformitate cu cerin?ele esen?iale ?i alte prevederi relevante ale Directivei 1999/5/
CE. Slovensko (Slovenian):
Cisco Systems, Inc. izjavlja, da je ta wireless device v skladu z bistvenimi zahtevami in ostalimi relevantnimi dolocili direktive 1999/5/ES. Slovensky (Slovak):
Cisco Systems, Inc. tmto vyhlasuje, e wireless device splna zkladn poiadavky a vetky prslun ustanovenia Smernice 1999/5/ES. Suomi (Finnish):
Cisco Systems, Inc. vakuuttaa tten ett wireless device tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen. Svenska (Swedish):
Hrmed intygar Cisco Systems, Inc. att denna wireless device str I verensstmmelse med de vsentliga egenskapskrav och vriga relevanta bestmmelser som framgr direktiv 1995/5/EG. CE Marking The following CE Mark is affixed to the equipment and its packaging:
EU Radiation Exposure Statement This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm 22 between the radiator and your body. U.S. Regulatory Wireless Notice FCC Compliance Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution Any changes or modifications not expressly approved by Cisco Systems, Inc. could void the users authority to operate this equipment. This Transmitter must not be co-located or operation in conjunction with any other antenna or transmitter. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 51cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IEEE 802.11b or 802.11g operation of this product in the USA is firmware-limited to channels 1 through 11. FCC Registration Requirement Section 15.407 of the FCC rules establishes filing requirements for U-NII operators that deploy a collection of more than 1000 outdoor access points operating in the 5.15-5.25 GHz band. Such operators must submit a letter to the FCC lab acknowledging that, should harmful interference to licensed services in this band occur, they will be required to take corrective action. Corrective action may include reducing power, turning off devices, changing frequency bands, and/or further reducing power radiated in the vertical direction. This material shall be submitted to:
Federal Communications Commission Laboratory Division, Office of Engineering and Technology 7435 Oakland Mills Road, Columbia, MD, 21046 Attn: U-NII Coordination or online at https://www.fcc.gov/labhelp Canadian Regulatory Wireless Notice 23 Industry Canada Statement This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme la norme CNR-210 dIndustrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. Industry Canada Caution
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
(ii) high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Avertissement:
(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;
(ii) De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., quils ont la priorit) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. Industry Canada Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 31 cm between the radiator & your body. Dclaration dexposition aux radiations Cet quipement est conforme aux limites dexposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 31 cm de distance entre la source de rayonnement et votre corps. Australia Radiation Exposure Statement This equipment complies with Australian radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. VCCI Statement for Japan VCCI-B Warning This is a Class B product based on the standard of the Voluntary Control 24 Council for Interference from Information Technology Equipment
(VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual. Taiwan Wireless Statements 12 14 Administrative Rules for Low-Power Radio-Frequency Devices Article 12: For those low-power radio-frequency devices that have already frequency devices that have already received a type-approval, companies, business units or users should not change its frequencies, increase its power or change its original features and functions. Article 14: The operation of the low-power radio-frequency devices is subject to the conditions that no harmful interference is caused to aviation safety and authorized radio station; and if interference is caused, the user must stop operating the device immediately and cant re-operate it until the harmful interference is clear. The authorized radio station means a radio-communication service operating in accordance with the Communication Act. The operation of the low-power radio-frequency devices is subject to the interference caused by the operation of an authorized radio station, by another intentional or unintentional radiator, by industrial, scientific and medical (ISM) equipment, or by an incidental radiator. 25
4.7 4.7.6 4.7.7 Low-Power Radio-Frequency Devices Technical Specifications 4.7: Unlicensed National Information Infrastructure 4.7.6: The U-NII devices shall accept any interference from legal communications and shall not interfere with the legal communications. If interference is caused, the user must stop operating the device immediately and must not re-operate it until the harmful interference is clear. 4.7.7: Manufacturers of U-NII devices are responsible for ensuring frequency stability such that an emission is maintained within the band of operation under all conditions of normal operation as specified in the user manual. Brazil Wireless Statement Este equipamento opera em carter secundrio, isto , no tem direito a proteo contra interferncia prejudicial, mesmo de estaes do mesmo tipo, e no pode causar interferncia a sistemas operando em carter primrio. This equipment operates on a secondary basis and consequently must accept harmful interference, including interference from stations of the same kind. This equipment may not cause harmful interference to systems operating on a primary basis. 26 This radio transmitter [FCC ID: UDX-600100011] has been approved by FCC to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. This radio transmitter [IC: 6961A-600100010] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Group Ant. No. Brand Model Name Antenna Type Connector 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 5 6 1 20 2 21+23 3 25 4 27
Grand-Tek Grand-Tek Grand-Tek Grand-Tek Grand-Tek Grand-Tek Grand-Tek Grand-Tek Grand-Tek Grand-Tek Grand-Tek Grand-Tek Grand-Tek Grand-Tek Grand-Tek Grand-Tek Senao Senao MA-ANT-20 MA-ANT-20 MA-ANT-20 MA-ANT-20 MA-ANT-23 MA-ANT-23 MA-ANT-21 MA-ANT-21 MA-ANT-25 MA-ANT-25 MA-ANT-25 MA-ANT-25 MA-ANT-27 MA-ANT-27 MA-ANT-27 MA-ANT-27 MR76 MR76 Omni Omni Omni Omni Sector Sector Sector Sector Sector Sector Sector Sector Sector Sector Sector Sector PIFA PIFA N-Type N-Type N-Type N-Type N-Type N-Type N-Type N-Type N-Type N-Type N-Type N-Type N-Type N-Type N-Type N-Type I-PEX I-PEX Group Ant. No. Gain (dBi) 2.4G 5G BT Elevation angle above 30 degrees Gain (dBi) 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 5 6 1 20 2 21+23 3 25 4 27
4 4
11 11
8.1 8.1
9.8 9.8
4.6
7 7
13 13
7.1 7.1
11.3 11.3 5.9
4.7
-1
-1
11.2 11.2
1.8 1.8
9.7 9.7 5.2
Remark Radio 1 Radio 1 Radio 2 Radio 2 Radio 1 Radio 1 Radio 2 Radio 2 Radio 1 Radio 1 Radio 2 Radio 2 Radio 1 Radio 1 Radio 2 Radio 2 Radio 3
(Scanning Radio) Radio 4 (BT LE) Le prsent metteur radio [IC: 6961A-600100010] a t approuv par Innovation, Sciences et Dveloppement conomique Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est suprieur au gain maximal indiqu pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de l'metteur.