This device complies with Industry Canada licenseexempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. The digital apparatus complies with Canadian CAN ICES3
(B)/NMB3(B). This radio transmitter (ISED certification number:
23749-246ATK2) has been approved by Industry Canada to operate with the antenna types listed with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. Ce dispositif est conforme la partie 15 des rgles de la FCC.(1) le dispositif ne peut pas causer des nuisances, et (2) le dispositif doit recevoir toute intensit, y compris celle qui peut causer une opration non dsire. Les modifications ou modifications qui ne sont pas expressment approuves par la partie responsable de la conformit peuvent confier lautorit de lutilisateur le fonctionnement du matriel. NOTE:Ces quipements ont t tests et jugs conformes aux limites dun appareil numrique de classe B.Ces limites sont conues pour assurer une protection raisonnable contre les nuisances dans une installation rsidentielleLa frquence de la radio et, si elle nest pas installe et utilise conformment aux instructions, peut provoquer des nuisances aux communications radio.Il ny a aucune garantie que lincident ne se produira pas dans une installation particulire, si ce matriel provoque une inactivit nocive la radio ou la tlvision.Lutilisateur est incit essayer de corriger lincident par une ou plusieurs des mesures suivantes:
Reorient ou relocalise les antennes bnficiaires. augmenter la sparation entre lquipement et le rcepteur. connecter le matriel un circuit diffrent de celui auquel le rcepteur est connect. consultez le ngociant ou un technicien de radio/
tlvision expriment pour laide. Lappareil a t conu pour rpondre aux exigences de lexposition gnrale en RF, il peut tre utilis sans restriction des conditions dexposition portable. Le prsentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitationestautorise aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareildoit accepter tout brouillageradiolec triquesubi, mmesi le brouillageest susceptible d'encompromettre le fonctionnement. Le prsent metteur radio (ISED certification number:
23749-246ATK2) a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-
dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur.