FCC ID: 2A6YG-WASHXS Moving light

POSEIDON wash xs manual WWW.CLF-LIGHTING.COM V1.0 JANUARY 2022 table of CONTENTS Dimensions Safety Instruction Fixture overview Introduction AC Power Power voltage Power cables Relaying power to other devices Data link Tips for reliable data transmission Physical installation Fastening the fixture to a flat surface Rigging via omega bracket Outdoor IP-rated fixtures Condensation/moisture inside housing Fixtures temperature specification Setup Control panel and menu navigation DMX address setting W-DMX control (optional q1 2019) Control mode Control panel Onboard control menus DMX protocols Arrangement of the LED groups 1-7 Static pixel effect chart Moving pixel effect chart Color Macro Chart Specifications 1 2 4 5 5 5 6 6 6 6 7 7 8 9 9 9 10 10 10 10 11 12 14 16 18 19 20 21 24 WWW.CLF-LIGHTING.COM Dimensions All dimensions are in millimeters 106 6 0 1 202 300 7 6 4 1 WWW.CLF-LIGHTING.COM Safety Instruction Read the safety precautions in this section before installing, powering, operating or servicing this WARNING!

product The following symbols are used to identify important safety information on the product and in this manual:

DANGER!

Safety hazard. Risk of severe injury or death. DANGER!

Hazardous voltage. Risk of lethal or severe electric shock. WARNING!

Fire hazard. WARNING!

LED light emission. Risk of eye injury. WARNING!

Burn hazard. Hot surface. Do not touch. WARNING!

Wear protective eyewear. WARNING!

Refer to user manual. Warning! Risk Group 1 (low risk) LED product according to EN 62471. Do not look into the beam at a distance of less than 8.3 meters from the front surface of the product. Do not view the light output with optical instruments or any device that may concentrate the beam. This product is for professional use only. It is not for household use. This product presents risks of severe injury or death due to fire and burn hazards, electric shock and falls. Read this manual before installing, powering or servicing the fixture, follow the safety precautions listed below and observe all warnings in this manual and printed on the fixture. If you have questions about how to operate the fixture safely, please contact your supplier. PROTECTION FROM ELECTRIC SHOCK Disconnect the fixture from AC power before removing or installing any cover or part and when not in use. Always ground (earth) the fixture electrically. Use only a source of AC power that complies with local building and electrical codes and has both overload and ground-fault (earth-fault) protection. Before using the fixture, check that all power distribution equipment and cables are in perfect condition and rated for the current requirements of all connected devices. Power input and throughput cables must be rated 20 A minimum, have three conductors 1.5 mm (16 AWG) minimum conductor size and an outer cable diameter of 5 - 15 mm. Cables must be hard usage type (SJT or equivalent) and heat-resistant to 90 C minimum. Use only PowerCON TRUE 1 cable connectors to connect to power input sockets. Use only PowerCON TRUE 1 cable connectors to connect to power through put sockets. Isolate the fixture from power immediately if the power plug or any seal, cover, cable, or other component is damaged, defective, deformed, wet or showing signs of overheating. Do not reapply power until repairs have been completed. Refer any service operation not described in this manual to a qualified technician. Socket outlets used to supply fixture fixtures with power or external power switches must be located near the fixtures and easily accessible so that the fixtures can easily be disconnected from power. 2 WWW.CLF-LIGHTING.COM PROTECTION FROM BURNS AND FIRE The exterior of the fixture becomes hot during use. Avoid contact by persons and materials. Allow the fixture to cool for at least 5 minutes before handling. Keep all combustible materials (e.g. fabric, wood, paper) at least 100 mm away from the fixture. Keep flammable materials well away from the fixture. Ensure that there is free and unobstructed airflow around the fixture. Do not illuminate surfaces within 200 mm of the fixture. Do not attempt to bypass thermostatic switches or fuses. If you relay power from one fixture to another using power throughput sockets, do not connect more than ten fixture fixtures in total to each other in an interconnected chain. Connect only other fixture fixtures to fixture power throughput sockets. Do not connect any other type of device to these sockets. Do not stick filters, masks or other materials onto any optical component. Do not modify the fixture in any way not described in this manual. PROTECTION FROM INJURY Do not look continuously at LEDs from a distance of less than 3 meters from the front surface of the fixture without protective eyewear such as shade 4-5 welding goggles. At less than this distance, the LED emission can cause eye injury or irritation. At distances of 3 meters and above, light output is harmless to the naked eye provided that the eyes natural aversion response is not overcome. Do not look at LEDs with magnifiers, telescopes, binoculars or similar optical instruments that may concentrate the light output. Ensure that persons are not looking at the LEDs from within 8.3 meters when the product lights up suddenly. This can happen when power is applied, when the product receives a DMX signal, or when SERVICE menu items are selected. Fasten the fixture securely to a fixed surface or structure when in use. The fixture is not portable when installed. Ensure that any supporting structure and/or hardware used can hold at least 10 times the weight of all the devices they support. Allow enough clearance around the head to ensure that it cannot collide with an object or another fixture when it moves. Check that all external covers and rigging hardware are securely fastened. Block access below the work area and work from a stable platform whenever installing, servicing or moving the fixture. Do not operate the fixture with missing or damaged covers, shields or any optical component. 3 WWW.CLF-LIGHTING.COM Fixture overview LCD Display WDMX Control buttons AC mains power input & output 5P DMX input 3P DMX input (accessoires)

# CLF-13-453 5P DMX output 3P DMX output (accessoires)

# CLF-13-454 4 WWW.CLF-LIGHTING.COM Introduction POWERFUL AND VERSATILE OUTDOOR LED WASH OUTDOOR LIGHTING ESSENTIAL TOURING - READY, COMPACT HOUSING 7 RGBL HIGH POWER LEDS 4 - 36 ZOOM ANGLE IP65 RATING Using for the first time Warning! Read Safety Information before installing, powering, operating or servicing the fixture. Before applying power to the fixture:

Check that the local AC mains power source is within the fixtures power voltage and frequency ranges. See Power cables and power plug on page 6. Install a PowerCON TRUE 1 power input connector power cable. AC Power Warning! Read Safety Information starting on before connecting the fixtures to AC mains power. Warning! For protection from electric shock, the fixture must be grounded (earthed). The power distributioncircuit must be equipped with a fuse or circuit breaker and ground-fault (earth-fault) protection. Warning! Socket outlets or external power switches used to supply the fixture with power must be located near the fixture and easily accessible so that the fixtures can easily be disconnected from power. Important! Do not insert or remove PowerCON TRUE 1 connectors to apply or cut power, as this may cause arcing at the terminals that will damage the connectors. Important! Do not use an external dimming system to supply power to the fixture, as this may cause damage to the fixture that is not covered by the product warranty. The fixture can be hard-wired to a electrical installation if you want to install it permanently, or a power plug that is suitable for the local power outlets can be installed on the power cable. Power voltage Warning! Check that the voltage range specified on the fixtures serial number label matches the local AC mains power voltage before applying power to the fixture. The fixtures accepts AC mains power at 100-240 V nominal, 50/60 Hz. Do not apply AC mains power to the fixture at any other voltage than specified. 5 WWW.CLF-LIGHTING.COM Power cables Power input and throughput cables must be rated 16A minimum, have three conductors 1.5 mm (16 AWG) minimum conductor size and an outer cable diameter of 5 - 15 mm. Cables must be hard usage type (SJT or equivalent) and heat- resistant to 90C minimum. In the EU the cable must be HAR approved or equivalent. If you install a power plug on the power cable, install a grounding-type (earthed) plug that is rated 16A minimum. Follow the plug manufacturers instructions. Table 1 shows standard wire color-coding schemes and some possible pin identification schemes; if pins are not clearly identified. Wire Color (EU models) Wire Color (US models) Conductor Symbol Brown Blue Yellow/Green Black White Green Live Neutral L N Ground (earth) or Table 1: Wire color-coding and power connections Relaying power to other devices Warning! Do not connect more than seven fixtures in total to AC mains power in one interconnected chain. Power can be relayed to another device via the PowerCON TRUE 1 throughput socket. If you daisy chain the fixtures in a chain so that they all draw AC mains power via the first fixture, certain points must be respected:

A heavy duty, three-conductor, 16 AWG or 1.5 mm2 cable with SJT or equivalent cable jacket must be used to connect the first fixture to AC mains power. PowerCON TRUE 1 connectors must be used to draw AC mains power from the fixtures power throughput sockets and yellow PowerCON TRUE 1 connectors must be used to supply power at the fixtures power input sockets. No matter what the AC mains power voltage is, do not connect more than ten the fixture in total ( including the first fixture) to AC mains power in one interconnected daisy chain using power input and through out connectors. Data link A DMX 512 data link is required in order to control a fixture via DMX. The fixture has 5-pin XLR connectors for DMX data input and output. The pin-out on all connectors is pin 1 = shield, pin 2 = cold (-), and pin 3 = hot (+) Pins 4 and 5 in the 5-pin XLR connectors are not used. Tips for reliable data transmission To connect the fixture to data:

1. Connect the DMX data output from the controller to the 5-pin XLR connector of the nearest fixture. 2. Connect the DMX output of the fixture closest to the controller to the DMX input of the next fixture and continue connecting fixtures output to input. 6 WWW.CLF-LIGHTING.COM Physical installation Warning! The fixture must be either fastened to a flat surface such as a stage or wall, or clamped to a truss or similar structure in any orientation using a rigging clamp. Warning! If the fixture can cause injury or damage if it falls, attach an approved safety cable to one of the safety cable attachment points on the base (see Fixture overview). Check that all surfaces to be illuminated are minimum 200 mm. from the fixture, that combustible materials

(wood, fabric, paper, etc.) are minimum 100 mm. from the fixture, that there is free airflow around the fixture and that there are no flammable materials nearby. Fastening the fixture to a flat surface The fixture can be fastened to a fixed flat surface that is oriented at any angle. Check that the surface can support at least 10 times the weight of all fixtures and equipment to be installed on it. Warning! The supporting surface must be hard and flat or cooling may be blocked, which will cause overheating. Fasten the fixture securely. Do not stand it on a surface or leave it where it can be moved or can fall over. Attach a securely anchored safety cable to the safety cable attachment point (see Fixture overview) if the fixture is to be installed in any location where it may fall and cause injury or damage if the primary attachment fails. 1. Block access under the work area. Working from a stable platform, hang the fixture on the truss with the arrow on the base towards the area to be illuminated. Tighten the rigging clamp. 2. Secure the fixture against clamp failure with a secondary attachment such as an approved safety cable that is rated for the weight of the fixture using one of the attachment points at the edges of the base (see Fixture overview). Do not use any other part of the fixture as a safety cable attachment point. The installation of the fixture has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation. The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net. This secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails. When rigging, derigging or servicing the fixture staying in the area below the installation place, on bridges, under high working places and other endangered areas is forbidden. The operator has to make sure that safety-relating and machine-technical installations are approved by an expert before taking into operation for the first time and after changes before taking into operation another time. The operator has to make sure that safety-relating and machine-technical installations are approved by an expert after every four year in the course of an acceptance test. The operator has to make sure that safety-relating and machine-technical installations are approved by a skilled person once a year. The fixture should be installed outside areas where persons may walk by or be seated. IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including (but not limited to) calculating working load limits, installation material being used, and periodic safety inspection of all installation material and the projector. If you lack these qualifications, do not attempt the installation yourself, but instead use a professional structural rigger. Improper installation can result in bodily injury or damage to property.The fixture has to be installed out of the reach of people. 7 WWW.CLF-LIGHTING.COM If the fixture shall be lowered from the ceiling or high joists, professional trussing systems have to be used. The fixture must never be fixed swinging freely in the room. Caution: Fixture may cause severe injuries when crashing down! If you have doubts concerning the safety of a possible installation, do not install the moving head!

Before rigging make sure that the installation area can hold a minimum point load of 10 times the fixtures weight. When installing the device, make sure there is no highly inflammable material (decoration articles, etc.) in a distance of min. 0.4 m. Use an appropriate clamp to rig the fixture on the truss. Follow the instructions mentioned at the bottom of the base. Make sure that the device is fixed properly! Ensure that the structure (truss) to which you are attaching the fixtures is secure. The fixture can be placed directly on the stage floor or rigged on a truss without altering its operation characteristics . For securing the fixture to the truss, install a safety wire which can hold at least 10 times the weight of the fixture. Use only the safety wire with a snap hook with screw lock gate. Fasten the safety cable in the attachment point and around the truss as shown on the picture below. Rigging via omega bracket:

Clamp Safety chain Truss Omega bracket with Quicklock # 520114/520113

(accessoires) 8 WWW.CLF-LIGHTING.COM Outdoor IP-rated fixtures CLF products are applied to official classified IP norm levels. For this product the IP rate is IP65 when using the covers for the chassis parts. IP65 means according classified norm: shielded against dust and pressurized water from any side. Typical use for outdoor rated stage events with normal weather acceptance. So no heavy rain, because then the water pressure over exceeds the IP norm. Protected against a solid object greater than 50mm such as a hand. Protected against vertical falling drops of water. Limited ingress permitted. Protected against a solid object greater than 12.5mm such as a finger. Protected against a solid object greater than 2.5mm such as a screwdriver. Protected against vertical falling drops of water with enclosure tilted up to 15 degrees from the vertical. Limited ingress permitted. Protected against sprays of water up to 60 degrees from the vertical. Limited ingress permitted. Protected against a solid object greater than 1mm such as a wire. Protected against water splashes from all directions. Limited ingress permitted. Dust protected. Limited ingress of dust permitted. Will not interfere with operation of the equipment. Protected against jets of water. Limited ingress permitted. Dust tight. No ingress of dust. Protected against powerful jets of water. Limited ingress permitted. Protected against the effects of immersion in water between 15cm and 1m for 30 minutes. Protected against the effects of immersion in water under pressure for long periods. Moisture 1 2 3 4 5 6 7 8 solid object 1 2 3 4 5 6 6 5 IP Ingress Protection Condensation/moisture inside housing Because of high humidity levels during production condensation can occur inside the housing. This is mostly visible on the coldest parts of the fixture, like the front glass or display. To prevent this problem we work with special conditioned areas for outdoor fixtures. Because of the breathing air valves it is still possible to get humidity inside the fixture. This will evaporate slowly. Do not put wet fixtures in a flightcase, this will help humidity enter the fixture. Fixtures temperature specification Make sure the fixture is used within its working temperature range. Outside this range we cannot guarantee correct operation. Temporary usage:

Stage event equipment is designed with temporary use in mind. Our product purpose is for theatre, festival, (disco) clubs and indoor &

outdoor concerts. Long term use is possible but keep in mind that it can bring damage to aging materials and affect the coated surface (

i.e. stainless steel). Rubber sealings will be negatively affected after long-term UV exposure and should be checked by qualified service technicians over time. Tighten screws too hard will also affect the IP-rating. 9 WWW.CLF-LIGHTING.COM Setup Warning! Read Safety Information before installing, powering or operating the fixture. Control panel and menu navigation The onboard control panel and backlit graphic display are used to set the fixtures DMX address, configure individual fixture settings

(personality), read out data and execute service utilities. See Onboard control menus for a complete list of menus and commands. Using the control buttons To enter the menu select [MODE]. Press [UP] and [DOWN] to scroll within a menu or adjust values. To enter a menu, select a function or apply a selection, press [ENTER]. To escape a function or move back one level in the menu structure, press [MODE]. Hold [MENU] = highlight for 15 seconds Press [UP] and [DOWN] together to rotate display DMX address setting The DMX address, also known as the start channel, is the first channel used to receive instructions from the controller. For independent control, each fixture must be assigned its to a separate channel. The DMX address can be configuredas by using the DMX ADDRESS menu in the control panel. For setting the DMX address press [ENTER] before you can change the address. The main screen will show a dot and the backlight will be switched off when a DMX signal is detected. The fixture is fully RDM ready. So when you are using a RDM ready console you can address the unit and read out its complete status. For RDM functions please refer to the ANSI/ESTA E1.20-2006 standard W-DMX control Go to the W-DMX section in the main menu, press the button UP to switch off Wireless DMX or disconnect with all connected Transmitters. Press the button DOWN to set the unit in the ready to connect with all not connected transmitters mode. If you press the mode button on the Wireless sollution transmitter all the units in this mode will be connected. If the unit is successfully connected in the home display the sign display the sign

: X . If the unit is switched off in the home display the sign

: V appears. If the unit is not connected to a transmitter in the home

: OFF . Holding the MENU and ENTER button for more than 3 seconds, the wireless board will reset. Do not use Wireless DMX and Wired DMX at the same time because it will give unwanted interference 10 WWW.CLF-LIGHTING.COM Control mode DMX control mode is selected in the CONTROL MODE menu. The fixture can be controlled with 3 DMX control modes:

Small-20CH Medium-27CH Large-55CH Shutter Dimmer Dimmer fine Pan Pan fine Tilt Tilt fine P/T speed/time Zoom Function set, Macro color RGBL RGBL fine LED 1-7 (RGBL) CCT CCT channel tint Static pixel effect Move pixel effect Move pixel effect speed Crossfade/dimmer Back ground color Back ground dimmer 11 WWW.CLF-LIGHTING.COM control panel Here you can set all functions for the fixture. Personality FANS Dimmer speed Dimmer curve WDMX Reset LED Calibration Refresh rate DMX HOLD Display Indicator Light Zoom Option KEY-Lock Regulated = power : Min 84.5%, FAN : variable Full = power : Min 84.5%, FAN : 4000RPM Silent 1 = power : Min 60%, FAN : 2240RPM Silent 2 = power : Min 40% ,FAN : 1840RPM Normal means select linear dimming, or choose dimmer 1-4 to control the dimming speed, dimming 1 of the fastest dimming curves, 4 for the most slowly dimming curve. Linear / Square law / INV Square law / S- Curve / Special Reset the Wireless Board Normal = Color calibration mode off FACTORY = Factory calibration mode, All colors are calibrated Controls the flicker frequency of the fixture 1200 / 2400 / 4800 / 10000 Hz DMX HOLD = The fixture will remember on last values when you disconnect DMX NO DMX HOLD = The fixture has no output when you disconnect DMX Rotate:

Auto=

Normal=

Background Light:

always on =

Auto off =

Auto Display Flip Function enabled Auto Display Flip Function disbaled Display background Light always on Display deactivation after approximately 15 second of inactivity BL blinking when no DMX :

Yes =

NO =

When there is no Dmx , the dmx value will be blinking on main menu When there is no dmx , the dmx value will be static on main menu On = When the display is standby, there are 2 low brightness dots visible to show that the fixture is on and dmx Off = When the display is standby, no dot visible to show Normal= zoom max 30 Wide= zoom max 36 Locks all the button functions. Standard unlocking password is

(MENU+UP+MENU+DOWN+MENU+UP+MENU+DOWN+ENTER) Font selection Select display font 12 WWW.CLF-LIGHTING.COM Dimmer mode provides five dimming options (see picture below):

LINEAR the increase in light intensity appears to be linear as DMX value is increased. SQUARE LAW light intensity control is finer at low levels and coarser at high levels. INV Square law light intensity control is coarser at low levels and finer at high levels. S-CURVE light intensity control is finer at low levels and high levels and coarser at medium levels. Special the light intensity was linear increase with DMX value , and light intensity control is finer at low level with DMX values decrease , the dimmer speed will also has effect on it. Whichever DIMMER CURVE option you select, you can choose between NORMAL or SMOOTH 1 / 2 / 3 / 4 dimming settings:

NORMAL is the default setting. It gives a virtually instantaneous reaction when you dim from one intensity to another, but dimming slowly from one intensity to another may appear slightly uneven. The MOOTH 1 / 2 / 3 / 4 setting gives smoother dimming during slow changes in intensity, but it limits the speed of dimming changes slightly. This makes it ideal for slow, smooth dimming, but a short time-lag may be noticeable if you try to dim quickly from one intensity to another. 13 WWW.CLF-LIGHTING.COM Onboard control menu NO. Main menu Menu level 2 Menu level 3 1 DMX ADDRESS Set DMX Address

<001>

DMX Signal Mode wire / wireless 2 CONTROL MODE Mode 1 - 20CH Mode 2 - 27CH Mode 3 - 55CH 1.Shutter, 2.Dimmer, 3.Pan, 4.Pan fine, 5.Tilt, 6.Tilt fine, 7.P/T speed/time, 8.Zoom, 9.Function set, 10.Macro color, 11.Red, 12.Green, 13.Blue, 14.Lime, 15.Static pixel effect, 16.M.P effect, 17.M.P effect speed, 18.Crossfade/dimmer, 19.BG color, 20.BG dimmer 1.Shutter, 2.Dimmer, 3.Dimmer fine, 4.Pan, 5.Pan fine, 6.Tilt, 7.Tilt fine, 8.P/T speed/time, 9.Zoom, 10.Function set, 11.Macro color, 12.Red, 13.Red fine, 14.Green, 15.Green fine, 16.Blue, 17.Blue fine, 18.Lime, 19.Lime fine, 20.CCT, 21.CCT channel tint, 22.Static pixel effect, 23.M.P effect, 24.M.P effect speed, 25.Crossfade/dimmer, 26.BG color, 27.BG dimmer 1.Shutter, 2.Dimmer, 3.Dimmer fine, 4.Pan, 5.Pan fine, 6.Tilt, 7.Tilt fine, 8.P/T speed/time, 9.Zoom, 10.Function set, 11.Macro color, 12.Red, 13.Red fine, 14.Green, 15.Green fine, 16.Blue, 17.Blue fine, 18.Lime, 19.Lime fine, 20.Red 1, 21.Green 1, 22.Blue 1, 23.Lime 1, 24.Red 2, 25.Green 2, 26.Blue 2, 27.Lime 2, 28.Red 3, 29.Green 3, 30.Blue 3, 31.Lime 3, 32.Red 4, 33.Green 4, 34.Blue 4, 35.Lime 4, 36.Red 5, 37.Green 5, 38.Blue 5, 39.Lime 5, 40.Red 6, 41.Green 6, 42.Blue 6, 43.Lime 6, 44.Red 7, 45.Green 7, 46.Blue 7, 47.Lime 7, 48.CCT, 49.CCT channel tint, 50.Static pixel effect, 51.M.P effect, 52.M.P effect speed, 53.Crossfade/dimmer, 54.BG color, 55.BG dimmer Remark Default : 001 Default : wire Default : 27CH 3 Motor Pan invert Tilt invert Normal / Inverted Normal / Inverted Pan/Tilt Swap Normal / Inverted Default : Normal Default : Normal Default : Normal FANS Regulated / Full / Silent 1 / Silent 2 Default : Regulated Dimmer Speed Normal / Smooth 1 / Smooth 2 / Smooth 3 / Smooth 4 Default : Normal Dimmer Curve Linear / Square law/INV Square law / S-curve / Special Default : Linear WDMX Reset Reset the Wireless ?

LED Calibration Factory / Normal Default : Factory Calibration P/T Motor calibration Tilt offset (-128 ~ +127) Pan offset (-128 ~ +127) Zoom calibration Offset (-19 ~ +19) 4 PERSONALITY Refresh Rate 1200Hz / 2400Hz / 4800Hz / 10000Hz DMX hold Dmx hold / No dmx hold Default : 1200Hz Default : Dmx hold Rotate Auto / Normal Default : Normal Display Background Light Always on / Auto off (15S) Default : Auto off BL blinking when no DMX Yes ~ no Indicator Light On / Off Zoom Option Normal / Wide Key Lock On / Off Default : Yes Default : Off Default : Normal Default : Off Font selection Helvetica / Arial / Univers / Calibri / Big_noodle_titling / Gill Default : Helvetica Sans / Book Antiqua 14 WWW.CLF-LIGHTING.COM Fixed color R, G, B, L, RG, RB, GB, RGB, RL, GL, BL, RGL, RBL, GBL, RGBL Default : RGBL CCT 2500K / 2800K / 3200K / 4000K / 5000K / 5600K / 6000K /

7000K / 8000K / 9000K /10000K Default : 2500K 5 STATIC COLOR Manual color Pan Pan fine Tilt Tilt fine Zoom Auto Speed Pan 6 AUTO COLOR Pan fine Tilt Tilt fine Zoom Dimmer Red Green Blue Lime Strobe 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 01 - 20 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 Default : 000 Default : 000 Default : 000 Default : 000 Default : 000 Default : 000 Default : 000 Default : 000 Default : 000 Default : 000 Default : 000 Default : Auto 01 Default : 000 Default : 000 Default : 000 Default : 000 Default : 000 Default : 000 7 Test Test led / Test pan / Test tilt / Test zoom / Test all Software version Display board Vx.xx Pan/Tilt board Vx.xx Led board Vx.xx Usage time TOTAL: Xxxx H LED total: Xxxx H Temperature Head: XXXC (Stored max: XXXC,Stored min: XXXC) Base: XXXC (Stored max: XXXC,Stored min: XXXC) 8 INFO Humidity Head: xx%RH (Stored max: XXXRH,Stored min: XXXRH) Base: xx%RH (Stored max: XXXRHStored min: XXXRH) Fan xxx RPM xx%

RDM.UID 0x02E2003xxxxx DMX LIVE Show all received DMX data No errors detected boards health status Error code:

Error information Pan&Tilt resetting 9 Reset Zoom motor resetting Factory reset Clear error message?

15 WWW.CLF-LIGHTING.COM DMX protocols 20 CH 27 CH 54 CH Function 1 1 1 Shutter 2 3 4 5 6 7 8 2 3 4 5 6 7 8 9 2 3 4 5 6 7 8 9 Dimmer Dimmer fine Pan Pan fine Tilt Tilt fine P/T speed/time Zoom Remark Value 000 - 019 020 - 024 025 - 064 065 - 069 070 - 084 085 - 089 090 - 104 105 - 109 110 - 124 125 - 129 130 - 144 145 - 149 150 - 164 165 - 169 170 - 184 185 - 189 190 - 204 205 - 209 210 - 224 225 - 229 230 - 244 245 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 Setting No function Shutter open Strobe 1 (fast slow) Shutter open Strobe 2: opening pulse (fast slow) Shutter open Strobe 3: closing pulse (fast slow) Shutter open Strobe 4: random strobe (fast slow) Shutter open Strobe 5: random opening pulse (fast slow) Shutter open Strobe 6: random closing pulse (fast slow) Shutter open Strobe 7: burst pulse (fast slow) Shutter open Strobe 8: random burst pulse (fast slow) Shutter open Strobe 9: sine wave (fast slow) Shutter open Strobe 10: burst (fast slow) Shutter open 0 - 100%

0 - 100%

Pan movement by 540 Fine control of pan movement Tilt movement by 270 Fine control of tilt movement Fast Slow 0-100% (wide 36 - narrow 4) 16 WWW.CLF-LIGHTING.COM Remark Value must be held for 3 seconds to activate. 20 CH 27 CH 54 CH Function Value Setting 000 - 009 No function 010 - 014 015 - 059 060 - 064 065 - 069 070 - 074 075 - 079 080 - 089 090 - 094 095 - 099 100 - 104 105 - 129 130 - 134 135 - 139 140 - 144 145 - 149 150 - 154 155 - 159 160 - 164 165 - 169 170 - 174 175 - 179 180 - 184 185 - 189 190 - 194 195 - 199 200 - 204 205 - 209 210 - 214 215 - 219 230 - 234 235 - 239 240 - 244 245- 249 250 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 Reset entire fixture No function Fan mode REGULATED Fan mode FULL Fan mode SILENT 1 Fan mode SILENT 2 No function Calibrated color output mode- Calibrated= ON No function Raw color output mode- Calibrated = OFF No function 1200 Hz Refresh rate 2400 Hz Refresh rate 4800Hz Refresh rate 10000Hz Refresh rate No function Zoom Option - Normal No function Zoom Option - Wide No function WDMX - RESET No function Dimmer Speed -- Normal No function Dimmer Speed -- Smooth 1 Dimmer Speed -- Smooth 2 Dimmer Speed -- Smooth 3 Dimmer Speed -- Smooth 4 No function Pan/tilt motor reset No function Zoom motor reset No function Illuminate display Please see page 21 Color macro chart 0 - 100%

0 - 100%

0 - 100%

0 - 100%

0 - 100%

0 - 100%

0 - 100%

0 - 100%

0 - 100%

0 - 100%

0 - 100%

0 - 100%

0 - 100%

0 - 100%

0 - 100%

0 - 100%

0 - 100%

0 - 100%

0 - 100%

0 - 100%

0 - 100%

0 - 100%

0 - 100%

0 - 100%

9 10 10 Fixture control settings 10 11 12 13 14 11 12 13 14 15 16 17 18 19 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 Color macro Red Red fine Green Green fine Blue Blue fine Lime Lime fine Red 1 Green 1 Blue 1 Lime 1 Red 2 Green 2 Blue 2 Lime 2 Red 3 Green 3 Blue 3 Lime 3 Red 4 Green 4 Blue 4 Lime 4 17 WWW.CLF-LIGHTING.COM 20 CH 27 CH 54 CH Function Value Setting Remark 36 37 38 39 40 41 42 43 44 45 46 47 48 Red 5 Green 5 Blue 5 Lime 5 Red 6 Green 6 Blue 6 Lime 6 Red 7 Green 7 Blue 7 Lime 7 CCT 49 CCT channel tint Static pixel effect Moving pixel effect 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 005 006 - 255 000 001-127 128-128 129-255 000 - 255 000 - 255 0 - 100%

0 - 100%

0 - 100%

0 - 100%

0 - 100%

0 - 100%

0 - 100%

0 - 100%

0 - 100%

0 - 100%

0 - 100%

0 - 100%

No function 10000k - 2500k No Function Magenta - Neutral Neutral Neutral - Green Please see page 19 Static effect Please see page 20 Moving effect Moving effect speed 000 - 255 Slow Fast Crossfade/dimmer 000 - 255 Fast Slow Background color 000 - 255 Please see page 21 Color macro chart Background dimmer 000 - 255 0 - 100%

20 21 22 23 24 25 26 27 15 16 17 18 19 20 50 51 52 53 54 55 Arrangement of the LED groups 1-7 The Pan/Tilt values are at 128/35. The display is facing towards you. 4 5 3 67 12 18 WWW.CLF-LIGHTING.COM Static pixel effect chart Background color(White): control by Background Macro color channel value. Static pixel color(Blue): control by RGBL / Macro / CCT channel value. No. Dmx Value Pixel No. Dmx Value Pixel 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 000 - 004 No funtion 005 - 009 010 - 014 015 - 019 020 - 024 025 - 029 030 - 034 035 - 039 040 - 044 045 - 049 050 - 054 055 - 059 060 - 064 065 - 069 070 - 074 075 - 079 080 - 084 085 - 089 090 - 094 095 - 099 100 - 104 105 - 109 110 - 114 115 - 119 120 - 124 125 - 129 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 130 - 137 135 - 139 140 - 144 145 - 149 150 - 154 155 - 159 160 - 164 165 - 169 170 - 174 175 - 179 180 - 184 185 - 189 190 - 194 195 - 199 200 - 204 205 - 209 210 - 214 215 - 219 220 - 224 225 - 229 230 - 234 235 - 239 240 - 244 245 - 249 250 - 254 255 19 WWW.CLF-LIGHTING.COM Moving pixel effect chart Background color(White): control by Background Macro color channel value. Move pixel color(Red): control by RGBL / Macro / CCT channel value. Pixel Dmx Value step 1 step 2 step 3 step 4 step 5 step 6 step 7 step 8 step 9 step10 step11 step12 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 000 - 004 No funtion 005 - 009 010 - 014 015 - 019 020 - 024 025 - 029 030 - 034 035 - 039 040 - 044 045 - 049 050 - 054 055 - 059 060 - 064 065 - 069 070 - 074 075 - 079 080 - 084 085 - 089 090 - 094 095 - 099 100 - 104 105 - 109 110 - 114 115 - 119 120 - 255 20 WWW.CLF-LIGHTING.COM Color Macro Chart DMX value Gel Name Color Number DMX value Gel Name Color Number 0-4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 no function Rose Pink Medium Bastard Amber Pale Yellow Dark Salmon Pale Amber Gold Medium Yellow Straw Tint Deep Straw Surprise Peach Medium Amber Dark Amber Sunset Red Bright Red Medium Pink Rose Purple Lavender Pale Blue Sky Blue Tokyo Blue Evening Blue Lime Green Moss Green Dark Yellow Green Yellow Straw Deep Amber Orange Primary Red Light Rose English Rose Light Salmon Middle Rose Dark Pink Magenta Peacock Blue Steel Blue Light Blue Dark Blue LEE Green LEE 002 LEE 004 LEE 007 LEE 008 LEE 009 LEE 010 LEE 013 LEE 015 LEE 017 LEE 020 LEE 022 LEE 025 LEE 026 LEE 036 LEE 048 LEE 058 LEE 063 LEE 068 LEE 071 LEE 075 LEE 088 LEE 089 LEE 090 LEE 101 LEE 103 LEE 104 LEE 105 LEE 106 LEE 107 LEE 108 LEE 109 LEE 110 LEE 111 LEE 113 LEE 115 LEE 117 LEE 118 LEE 119 LEE 121 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 Fern Green Dark Green Mauve Smokey Pink Bright Pink Marine Blue Medium Blue Golden Amber Deep Golden Amber Special Lavender Pale Green Primary Green Summer Blue Bright Blue Pale Violet Pale Navy Blue No Colour Blue Apricot Bright Rose Gold Tint Pale Gold Pale Salmon Pale Rose Chocolate Pink Deep Orange Slate Blue Bastard Amber Flame Red Daylight Blue Deep Lavender Lagoon Blue Dark Steel Blue Loving Amber Chrome Orange Dark Lavender Congo Blue Moonlight Blue Flesh Pink Surprise Pink LEE 122 LEE 124 LEE 126 LEE 127 LEE 128 LEE 131 LEE 132 LEE 134 LEE 135 LEE 137 LEE 138 LEE 139 LEE 140 LEE 141 LEE 142 LEE 143 LEE 144 LEE 147 LEE 148 LEE 151 LEE 152 LEE 153 LEE 154 LEE 156 LEE 157 LEE 158 LEE 161 LEE 162 LEE 164 LEE 165 LEE 170 LEE 172 LEE 174 LEE 176 LEE 179 LEE 180 LEE 181 LEE 183 LEE 192 LEE 194 21 WWW.CLF-LIGHTING.COM DMX value Gel Name Color Number DMX value Gel Name Color Number 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 Zenith Blue True Blue Alice Blue Palace Blue Regal Blue Double CTB Full CTB Half CTB Quarter CTB Full CTO Half CTO Quarter CTO Full CTO + .3 ND Full CTO + .6 ND LCT Yellow (Y1) White Flame Green LEE Fluorescent Green LEE 195 LEE 196 LEE 197 LEE 198 LEE 199 LEE 200 LEE 201 LEE 202 LEE 203 LEE 204 LEE 205 LEE 206 LEE 207 LEE 208 LEE 212 LEE 213 LEE 219 Super Correction LCT Yellow LEE 230 Super Correction W.F. Green LEE 232 HMI (to Tungsten) CID (to Tungsten) CSI (to Tungsten) LEE 236 LEE 237 LEE 238 LEE Fluorescent 5700 Kelvin LEE 241 LEE Fluorescent 4300 Kelvin LEE 242 LEE Fluorescent 3600 Kelvin LEE 243 LEE Plus Green Half Plus Green LEE Minus Green Half Minus Green Quarter Minus Green Three Quarter CTB One and a Half CTB Three Quarter CTO One and a Half CTO Double CTO Soft Green Jade Forest Green Follies Pink Special Rose Pink LEE 244 LEE 245 LEE 247 LEE 248 LEE 249 LEE 281 LEE 283 LEE 285 LEE 286 LEE 287 LEE 322 LEE 323 LEE 327 LEE 328 LEE 332 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 Special Medium Lavender Fuchsia Pink Glacier Blue Lighter Blue Special Steel Blue Special Medium Blue Cornflower Full CT Straw Half CT Straw Eighth CT Straw Double New Colour Blue LEE 343 LEE 345 LEE 352 LEE 353 LEE 354 LEE 363 LEE 366 LEE 441 LEE 442 LEE 444 LEE 500 New Colour Blue (Robertson Blue) LEE 501 Half New Colour Blue Waterfront Green Sally Green Marlene Madge Midnight Maya Argent Blue ALD Gold Full CT Eight Five Industry Sodium HI Sodium Urban Sodium Perfect Lavender Provence Special Pale Lavender Cold Lavender Lily King Fals Lavender Cool Lavender Electric Lilac Spir Special Blue Cold Blue Bedford Blue Elysian Blue Cabana Blue Mikkel Blue Colour Wash Blue Berry Blue LEE 502 LEE 504 LEE 505 LEE 506 LEE 507 LEE 508 LEE 525 LEE 550 LEE 604 LEE 650 LEE 651 LEE 652 LEE 700 LEE 701 LEE 702 LEE 703 LEE 704 LEE 706 LEE 708 LEE 709 LEE 710 LEE 711 LEE 712 LEE 714 LEE 715 LEE 716 LEE 719 LEE 721 22 WWW.CLF-LIGHTING.COM DMX value Gel Name Color Number DMX value Function setting 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 - 205 no function 206 - 215 colour rainbow 1 216 - 225 colour rainbow 2 226 - 235 colour rainbow 3 236 - 245 colour rainbow 4 246 - 255 colour rainbow 5 slow - fast slow - fast slow - fast slow - fast slow - fast Bray Blue Virgin Blue Ocean Blue Old Steel Blue QFD Blue Steel Green Scuba Blue Twickenham Green JAS Green Bram Brown Dirty White Easy White Seedy Pink Wheat Sun Colour Straw LEE Yellow Oklahoma Yellow Egg Yolk Yellow Burnt Yellow Rust Millennium Gold Bastard Pink AS Golden Amber Terry Red Moroccan Pink Vanity Fair Pretty 'n Pink Magical Magenta Special KH Lavender Color Effect CCT 1 CCT 2 CCT 3 CCT 4 CCT 5 CCT 6 CCT 7 CCT 8 CCT 9 LEE 722 LEE 723 LEE 724 LEE 725 LEE 727 LEE 728 LEE 729 LEE 736 LEE 738 LEE 742 LEE 744 LEE 747 LEE 748 LEE 763 LEE 764 LEE 765 LEE 767 LEE 768 LEE 770 LEE 777 LEE 778 LEE 779 LEE 780 LEE 781 LEE 790 LEE 793 LEE 794 LEE 795 LEE 799 2500K 2800K 3200K 4000K 5000K 5600K 6000K 7000K 8000K 9000K CCT 10 10,000K 23 WWW.CLF-LIGHTING.COM Specifications Power Input voltage & rate Standby power 100-240V, 50/60Hz 30W Nominal total power consumption (at nominal voltage 230V) 350W Typical current (at nominal voltage 230V) Cos Power plug type Configuration LED color LED color temperature Quantity of LED Dimming frequency Dimmer resolution Optical Beam angle Photometric Output @1M Output @5M Heat management Cooling type:

MAX. Ambient temp (Ta max) MIN. Ambient temp (Ta min) MAX housing temp.(ta=25C) MAX housing temp.(ta=40C) Menu Auto program Static color Manual calibration Factory calibration Strobe speed Random strobe Control 1.56A 0,974 Seetronic PowerCon True RGBL 2500 K - 10000 K 7 pcs 1200/2400/4800/10000 Hz 8bit / 16bit 4 - 36 9.000 lux 720 lux Passive cooling 40, C 25, C 50, C 65, C yes yes yes yes 0 - 20Hz yes

* PF = power factor. Measurements made at nominal voltage with all LEDs at full intensity. Allow for a deviation of +/- 10%. 24 WWW.CLF-LIGHTING.COM Control Control protocol DMX channel range RDM RDM compliance WDMX ACN DMX input connection Data input (artnet, SACN) Hardware Interface Software upload method Installation IP rating Housing Safety attachment point Physical Net product weight Machine dimensions - Length Machine dimensions - Width Machine dimensions - Height Accessories Included items Approvals USITT DMX512/1990 20 / 27 / 55 yes ANSI/ESTA E.120 Standard None DMX 5P in & out (3 pin possible with optional chassis part) None Backlite LCD display XLR & RJ45 IP65 Yes 12.7 kg 300 mm 205 mm 467 mm Power cable , manual Approved certifications CE / ROHS 25 WWW.CLF-LIGHTING.COM POSEIDON wash xs CLFLIGHTING WWW.CLF-LIGHTING.COM

Move light Model: CLF Poseidon WASH XS Rating: 100-240V~, 50/60Hz, 350W ta: 40C

(---0.2m|

The maximum total interconnected current: 8A Disconnect electrically before re-lamping Moving light IP66 FCCID : 2A6YG-WASHXS

Declaration of Authorization We Name: CLF LIGHTING B.V. Address: De Kazematten 19 City: Bemmel tees Country: The Netherlands. Declare that:

Name Representative of agent: EMTEK(DONGGUAN) CO., L Agent Company name: Sam Lv.......... Address: -1&2/F.,Building 2, Zone A, Zhongda Marine Biotechnology Reserch at Development Base, No.9, Xincheng Avenue, Songshanhu High-technology Industrial Development Zont City: Dongguan, Guangdong, Country i is authorized to apply for Certification of the following product(s):

Product description: ...Moving light.. Type designation: ...CLF Poseidon WASH XS Trademark:

Validity/ expiry date on our behaif. Date: ...2022-05-28.. City: Bemmel....... Name: VAN WORKUM THEO......... Function: Manage...........ccccescecesesenee Signature: Ly IK tytn g

(1): Required for FCC application

'2): For FCC it must be the Grantee Code owner or the authorized agent.

De Kazematten 49, e681 CS, Bemmel Bemmel The Netherlands Telefication B.V., Dept. FCC TCB Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands Subject: Request for confidentiality FCC ID: 2AG6YG-WASHXS Reference number: EDG2203250167E01601R Dear FCC TCB, Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application:

0 Bill(s) of Material &] Block Diagrams

{I Operational Description J Schematic Diagrams ( Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. Pursuant to Public Notice DA 04-1705 of the Commission's policy, der to comply with the market regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, applicant hereby requests Short-Term Confidential treatment of the following materials (See nofes below)

&] Internal Photos {&] User's Manual C) Test Set-up Photos OO External Photos Justification: The product h oles:

1) A document or type of document can only have ONE type of confidentiality!

2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max ) The planned date should stated in the RF731 application form 3) FCC must be informed when marketing begins earlier 4) Release takes place automatically thus extension must be requested n time Telefication does not remind you of this!

5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period Name and signature of applicant: VAN WORKUM THEO Uh Urreun FCC, Request for non-disclosure RF 501, Issue 8 ar-\e\= 9m Mo) amt}