FCC ID: 2AZ9G-CLMBR17002 Clmbr Connected

User Manual Version 3.0 2022/08 CLMBR-17002 Clmbr Connected About This Document No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of CLMBR, Inc. The information in this document is subject to change without notice. CLMBR makes no representations or warranties with respect to the contents herein, and specifically disclaims any implied warranties of merchantability or fitness for a particular purpose. CLMBR reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of CLMBR to notify any person of such revisions or changes. Windows is a registered trademark of Microsoft, Inc. Other brand or product names are trademarks of their respective holders. 1 Compliance Information For FCC (USA) Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

(1) lappareil ne doit pas produire de brouillage, et

(2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. FCC& IC Radiation Exposure Statement:

This equipment complies with FCC and Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Dclaration dIC sur lexposition aux radiations:

Cet quipement est conforme aux limites dexposition aux radiations dfinies par le Canada pour des environnements non contrls. Cet quipement doit tre install et utilis une distance minimum de 20 cm entre lantenne et votre corps. 2 |

Cet metteur ne doit pas tre install au mme endroit ni utilis avec une autre antenne ou un autre metteur. For IC (Canada) CAN ICES-003(B)/NMB-003(B) For CE (EU) The device complies with the radio equipment Directive 2014/53/EU 3 |

Renseignements relatifs la conformit Pour la FCC (tats-Unis). Attention : L'utilisateur est averti que les changements ou modifications non expressment approuvs par la partie responsable de la conformit pourraient annuler l'autorit de l'utilisateur utiliser l'quipement. Cet appareil est conforme la partie 15 des rgles de la FCC et aux normes RSS exemptes de licence d'Industrie Canada. Le fonctionnement est soumis aux deux conditions suivantes :

(1) cet appareil ne doit pas causer d'interfrences nuisibles, et

(2) cet appareil doit accepter toute interfrence reue, y compris les interfrences susceptibles de provoquer un fonctionnement indsirable. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

(1) lappareil ne doit pas produire de brouillage, et

(2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. REMARQUE : cet quipement a t test et dclar conforme aux limites d'un appareil numrique de classe B, conformment la partie 15 des rgles de la FCC. Ces limites sont conues pour fournir une protection raisonnable contre les interfrences nuisibles dans une installation rsidentielle. Cet quipement gnre, utilise et peut mettre de l'nergie de frquence radio et, s'il n'est pas install et utilis conformment aux instructions, peut causer des interfrences nuisibles aux communications radio. Cependant, il n'y a aucune garantie que des interfrences ne se produiront pas dans une installation particulire. Si cet quipement cause des interfrences nuisibles la rception radio ou tlvision, ce qui peut tre dtermin en teignant et en rallumant l'quipement, l'utilisateur est encourag essayer de corriger l'interfrence par une ou plusieurs des mesures suivantes :

-- Rorientez ou dplacez l'antenne de rception.

-- Augmenter la distance entre l'quipement et le rcepteur.

-- Brancher l'quipement sur une prise d'un circuit diffrent de celui sur lequel le rcepteur est connect.

-- Consultez le revendeur ou un technicien radio/TV expriment pour obtenir de l'aide. Dclaration d'exposition aux rayonnements FCC et IC :

Cet quipement est conforme aux limites d'exposition aux rayonnements de la FCC et du Canada tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec une distance minimale de 20 cm entre le radiateur et votre corps. Cet metteur ne doit pas tre co-localis ou fonctionner en conjonction avec une autre antenne ou un autre metteur. 4 |

Dclaration dIC sur lexposition aux radiations:

Cet quipement est conforme aux limites dexposition aux radiations dfinies par le Canada pour des environnements non contrls. Cet quipement doit tre install et utilis une distance minimum de 20 cm entre lantenne et votre corps. Cet metteur ne doit pas tre install au mme endroit ni utilis avec une autre antenne ou un autre metteur. Pour Industrie Canada Norme canadienne NMB-003(B) Pour la CE (UE) Cet quipement est conforme la directive 2014 / 53 / EU sur les quipements radio Usage Notice

! Warning - To prevent the risk of fire or shock hazards, and do not expose the product to moisture. 5 |

! Warning - Please do not open or disassemble the product as this may cause electric shock. Precautions Please follow all warnings, precautions and maintenance as recommended in this users manual to maximize the life of your unit. Do Turn off the product before cleaning. Use a soft cloth moistened with mild detergent to clean the product housing. Use only the qualified power adapter that comes with your device. Disconnect the power plug from AC outlet if the product is not going to be used for an extended period of time. Dont Do not use abrasive cleaners, waxes or solvents for your cleaning. Do not operate the product under the following conditions:

- Extremely hot, cold or humid environment.

- Areas susceptible to excessive dust and dirt.

- Near any appliance generating a strong magnetic field. Caution Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. Avis dutilisation

Mise en garde Pour prvenir les risques dincendie ou dlectrocution, ne pas exposer le produit lhumidit. 6 |

Mise en garde Prire de ne pas ouvrir ou dmonter le produit, car cela pourrait entraner llectrocution. Prcautions Veuillez suivre toutes les mises en garde, prcautions et entretiens recommands dans ce manuel dutilisation pour maximiser la dure de vie de votre unit. faire :

teindre lappareil avant de le nettoyer. Utiliser un chiffon humidifi par une solution savonneuse pour nettoyer le botier du produit. Utiliser uniquement ladaptateur dalimentation prescrit pour votre appareil. Dbrancher lappareil lorsquil nest pas utilis pendant une priode prolonge. viter :

Ne pas utiliser de nettoyants abrasifs, de cires ou de solvants pour le nettoyage Ne jamais utiliser lappareil dans les conditions suivantes :

des conditions environnementales extrmes (chaud, froid ou humidit) des endroits remplis de poussires et de salets. proximit dappareils produisant un fort champ magntique. Mise en garde Risque d'explosion si la batterie est remplace par un type incorrect. Jetez les piles usages conformment aux instructions. Table of Contents 7 |

Chapter 1 ........................................................................................................................ 9 1.1 Overview .................................................................................................................. 10 1.2 Feature ..................................................................................................................... 10 1.3 Specifications ........................................................................................................... 10 1.4 Block Diagram.......................................................................................................... 12 1.5 Interface Connectors ................................................................................................ 13 1.6 Package Overview ................................................................................................... 14 Chapter 2 ...................................................................................................................... 15 2.1 Power On / Off ......................................................................................................... 16 2.2 Dimension ................................................................................................................ 17 Appendix ...................................................................................................................... 18 Declaration of the Presence Condition of the Restricted Substances Marking .............. 19 8 |

Chapter 1 Product Introduction 9 |

1.1 Overview The CLMBR-17002 is a thinner 21.45" touch computer that offers a unique screw less design with expandability and flexibility, making expansion and accessory installation much easier. The versatility of CLMBR-17002 is an exceptional choice for applications in all fitness sectors. 1.2 Feature Support MTK MT8385 processor. Support Wi-Fi 802.11a/b/g/n/ac & BT5.0 1T1R. Support 8MP FF camera. Support screen rotation. Unique screw less design for better user experience. Patented I/O design for better wiring management while implementation. 1.3 Specifications System CPU GPU APU Memory Storage MTK MT8385, Quad-core Cortex-A73 up to 2.0GHz, Quad-core Arm Cortex-A53 up to 2.0GHz Mali-G72 MP3 up to 800MHz Dual-core APU up to 500MHz 6GB dual channel LPDDR4 64GB eMMC Input Power DC in 12V/4A Display Touch Audio Camera 10 |

Dual channel LVDS, resolution up to 1920x1080P60 ZCC 21.5-inch P-Cap touch sensor (EETI 80H84 controller), supports 10 fingers touch function. Woofer x 1 (4/5W) and Tweeter x 2 (4/2W) 8MP fixed-focus G-sensor Network External IO Ports Support screen rotation Wi-Fi 802.11a/b/g/n/ac, 2T2R Bluetooth 5.0 (Support BLE), 1T1R 1 x USB2.0 Type-C HOST 1 x 12V DC IN 1 x Power button 2 x Volume button (+/-) OS Version Android 11.0 or later Operation Temp 0C~40C Storage Temp.

-20C to 60C Operation Humidity 20~80%, Non-Condensing Storage Humidity 10~90%, Non-Condensing LCD Touch Panel Size 21.45 TFT LCD Brightness

(non-touch screen) Brightness

(P-CAP with ZCC) Typical 350 cd/m2; min. 320 cd/m2 Typical 212.5 cd/m2; min. 170 cd/m2 Number of Pixels 1920 (H) 1080 (V)/ 60Hz Touch Type P-CAP/ 10 points Environment Certificate Compliance CE, FCC, CB IP65 (Only Front Bezel) Dimension (W x H x D) 521.9 mm x 350.16 mm x 65 mm Net Weight Gross Weight 4.91 Kg TBD 11 |

1.4 Block Diagram 12 |

1.5 Interface Connectors 12V DC IN Pin #

Signal Name Pin #

Signal Name 1 12V 2 GND USB-C Pin # Signal Name Pin #

Signal Name A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 GND VBUS Dp1 Dn1 VBUS GND B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 GND VBUS Dn2 Dp2 VBUS GND 13 |

1.6 Package Overview Clmbr Connected Power Cord DC Power Supply

! Warning!

This product is intended to be supplied by a UL Listed Power Adapter, rated 12Vdc, 4A minimum. (complied with LPS or PS2) Tma = 40 degree C minimum, and the altitude of operation = 2000m minimum. If it needs further assistance with purchasing the power source, please contact to CLMBR for further information.

! Mise en garde!

Cet appareil est conu avec une alimentation de courant CA, dune tension nominale de 12Vdc, 4A minimum. (conforme au LPS ou PS2) Tma = 40 degrs C minimum et laltitude de lutilisation = 2000m minimum. Pour dautres conseils pour linstallation de la source dalimentation, communiquer avec CLMBR pour de plus amples renseignements. 14 |

Chapter 2 Product Installation 15 |

2.1 Power On / Off Power On/Off Function Description Power on Sleep Power off Press the power button 5 sec, device will reboot Press the power button to enter sleep mode, and press again to resume from sleep Press the power button 2 sec and click power off, device will enter deep sleep mode 16 |

2.2 Dimension Front View Side View Rear View Bottom View 17 |

Appendix 18 |

Declaration of the Presence Condition of the Restricted Substances Marking Clmbr Connected CLMBR-17002 Equipment name: Clmbr Connected Type designation (Type): CLMBR-17002 Restricted substances and its chemical symbols Unit Lead

(Pb) Mercury

(Hg) Cadmium

(Cd) Hexavalent chromium

(Cr+6) Polybrominated biphenyls

(PBB) Polybrominated diphenyl ethers

(PBDE) Plastic Parts Metal Parts Cable component LCD Panel Touch Panel PCBA

() Software Note 1Exceeding 0.1 wt %andexceeding 0.01 wt %indicate that the percentage content of the restricted substance exceeds the reference percentage value of presence condition. Note 2indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence. Note 3Theindicates that the restricted substance corresponds to the exemption. 19 |

+0 122mm _9 5 75mm Maison Neue Book

+0 47mm 9 9 Maison Neue Book Plaak 6 Ney Heavy Maison Neue Book;

MODEL No. CLMBR-17002 SERIAL NO.: TS2isCLMM!

Plaak 6 Ney Heavy Plaak 6 Ney Heavy Maison Neue Book Serial # and barcode are placeholders, barcode size: 48.Smmx2.3mm

CLMBR, INC. Authority letter FCC TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: 2AZ9G-CLMBR17002 To whom it may concern:

Date: 3/17/2023 We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Guangzhou branch and Kobe Jian in SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Guangzhou branch to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with CLMBR, INC.. This authorization is valid until further written notice from the applicant. Name (Printed): Kenny Rosenzweig Title: -

Signature:

On behalf of Company: CLMBR, INC.

CLMBR, INC. Confidential letter FCC To:

SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From: CLMBR, INC. 3033 E 1st Avenue Suite 501 Denver, Colorado, 80206, United States Regarding:

Confidentiality Request regarding application for FCC ID: 2AZ9G-CLMBR17002 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commissions rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Name (Printed): Kenny Rosenzweig Title: -

Signature:

On behalf of Company: CLMBR, INC.

TES 2nd Simulate Report WiFi antenna of FCD-215 CBR RevA 2022.07.25 / Raymond Wang EVERY CONNECTION COUNTS Building 2, Lane 270, Section 3, Beishen Road, Shenkeng District, Xinbei City, Taiwan. TEST DETAILS AND SPEC TE Engineering Location, Engineer Taiwan, Raymond Wang Customer Equipment Name TES Bands / Frequencies Requirements or Targets Test Equipment Test Report Type Antennas Task Band: WiFi F [MHz]: 2400-2500, 5150-5875 Target:

CST Preliminary 2195902 -1/-2 Simulate for currently placement Ant enna Gain (Peak)

< 1dBi 2 2020 TE Connectivity. Confidential & Proprietary. Do not reproduce or distribute externally including non-authorized representatives and distributors. Create a sustainable future by limiting print copies, and recycling paper. FCD-215 CBR Simulate the antenna performance for currently placement EVERY CONNECTION COUNTS Picture for Antenna Position Antenna Antenna Position 4 2020 TE Connectivity. Confidential & Proprietary. Do not reproduce or distribute externally including non-authorized representatives and distributors. Create a sustainable future by limiting print copies, and recycling paper. Picture for Antenna Position 6.6 mm 7.5 mm 45 mm Antenna Position 7.5 mm 5 2020 TE Connectivity. Confidential & Proprietary. Do not reproduce or distribute externally including non-authorized representatives and distributors. Create a sustainable future by limiting print copies, and recycling paper. Return Loss 6 2020 TE Connectivity. Confidential & Proprietary. Do not reproduce or distribute externally including non-authorized representatives and distributors. Create a sustainable future by limiting print copies, and recycling paper. 2D Radiation for 2450MHz Phi 0 Phi 90 Theta 90 8 2020 TE Connectivity. Confidential & Proprietary. Do not reproduce or distribute externally including non-authorized representatives and distributors. Create a sustainable future by limiting print copies, and recycling paper. 2D Radiation for 5470MHz Phi 0 Phi 90 Theta 90 9 2020 TE Connectivity. Confidential & Proprietary. Do not reproduce or distribute externally including non-authorized representatives and distributors. Create a sustainable future by limiting print copies, and recycling paper. TEST RESULT / CONCLUSION For the currently placement, the average gain of simulation result is better than -1dBi by CST. The performance of antenna without the antenna cable. The simulation results shown that the below antenna propose keep out area can provide good antenna performance. 6.6 mm 7.5 mm 45 mm 7.5 mm 10 2020 TE Connectivity. Confidential & Proprietary. Do not reproduce or distribute externally including non-authorized representatives and distributors. Create a sustainable future by limiting print copies, and recycling paper. WHEN TECHNOLOGY CONNECTS, SO DOES HUMANITY. EVERY CONNECTION COUNTS

SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Declaration Applicant Legal Business Name CLMBR, INC. Address Grantee Code FCC ID 3033 E 1st Avenue Suite 501 Denver, Colorado, 80206, United States 2AZ9G 2AZ9G-CLMBR17002 Authorized Contact Name Kenny Rosenzweig Contact Email Contact Phone krosenzweig@clmbr.com

(914)610-0486 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare;

a) b) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

labeling the equipment with the exact FCC ID as specified in this application,

(1)

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules, c) d) e) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. in accordance with ISO 17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements.

(1)

(2)

(3) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. the Applicant shall, upon request by SGS, at the Applicants expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) g) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Link to the Covered List: Covered List CLMBR, INC. (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. CLMBR, INC. (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered list, established pursuant to 1.50002, as an entity producing covered equipment. Applicant Signature:

Date:3/17/2023 Print Name:

Title:

Kenny Rosenzweig

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database QSF27-14-04 Rev 1.0 Rev. Feb 6, 2023 Page 1 of 1 Original Issue: Jan. 4, 2021

UNITED STATES DESIGNATED AGENT LETTER Date: 3/10/2023 TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Applicant Company Name: CLMBR, INC. Grantee Code:

Contact Name:

Address:

City/Province/Zip: Denver/Colorado/80206 Telephone:

Fax:

Email:

(914)610-0486 303-941-8807 krosenzweig@clmbr.com 2AZ9G Kenny Rosenzweig 3033 E 1st Avenue Suite 501 U.S. designated agent Company Name: CLMBR, INC. FRN:

Contact Name:

Address:

City/Province/Zip: Denver/Colorado/80206 Telephone:

Fax:

Email:

(914)610-0486 303-941-8807 krosenzweig@clmbr.com 0031016678 Kenny Rosenzweig 3033 E 1st Avenue Suite 501 Applicable Equipment: FCC ID: 2AZ9G-CLMBR17002 ATTN: Director of Certification:

We, CLMBR, INC.and CLMBR, INC. understand and acknowledge the applicants consent and the designated agents obligation to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and e-mail of the designated agent listed above. We, CLMBR, INC. and CLMBR, INC. acknowledge the applicants acceptance of its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. Applicant CLMBR, INC. U.S. designated agent CLMBR, INC. Name (Printed): Kenny Rosenzweig Name (Printed): Kenny Rosenzweig Title:-

Signature:

Title:-

Signature: