FCC ID: 2AY6A-M1 4G MIFI

Table of Contents 1. PRECAUTIONS 1 2. PARTS AND BUTTONS OF THE DEVICE 2 3. CHARGING 3 4. INSERTING/REMOVING CARDS 3 5. BASIC OPERATION 4 6. HOME SCREEN 5 7. ESTABLISH A NETWORK COMMECTION 6 8. LOG IN TO THE MANAGEMENT PAGE 8 9. MAKING AND RECEIVING CALLS 11 10. ANSWERING AND REJECTING CALLS 11 11. SEND SMS 12 12. SETTINGS 12 13. TF CARD 14 14. HOW TO CONNECT TO A COMPUTER 14 15. CARING FOR YOUR PHONE 15 16. FCC RF EXPOSURE INFORMATION 16 Micro-USB Connector Volume Button Speaker Touchscreen Power Button Microphone 3. CHARGING Insert the small end of the charging cable into the charge port, and connect the charger to a power outlet. 4. INSERTING/REMOVING CARDS Installing the card Insert your ngernail into the slot at the bottom left of the back cover, and Sliding nails across bottom of back cover to lift in o. Before installing the SIM card, please open the SIM card cover as shown below. 5.BASIC OPERATION 1). Power On/O Press and hold the Power Button for a few seconds to turn on the device. Press and hold the Power Button , and then tap Power o to turn o the device. 2). Turn On/O the screen When the screen is o, click the Power Button to light up the screen. Double-click the Power Button to turn o the screen, you can avoid unnecessary operations. 3). Screen operation a.Click on Tap with one nger to open an application, to select a menu item, or to press a displayed button. b.Slide Swipe left or right on the home screen or app screen to view other panels. Swipe down from the top on any screen to check the time, battery level and other information at any time. 6.HOME SCREEN The home screen will look similar to the picture below. The status bar displays system information, such as current time, wireless connectivity and battery charge status. 7. ESTABLISH A NETWORK COMMECTION Please turn on the screen to view the SSID and Wi Key of this machine. 1). PC (Take Windows 7 as an example) 1. Make sure that MiFi is turned on normally. 2.Turn on the computer , select Start > Control Panel >

Network and Internet >

Network and Sharing Center >

Connect to a network. 3.Select the wireless network consistent with MiFi's SSID in the wireless network list, and click Connect. 4. Enter the correct network security key(Wi Key). 5.Wait for a while, the wireless network connection icon will be displayed in the lower right corner of the computer screen. At this point, the wireless network connection is successful. 2). Mobile a.Android (Take Cloud Mobile Stratus C5 as an example) 1. Make sure that MiFi is turned on normally. 2.Turn on the phone, select Settings

> Network&internet > Wi-Fi, and turn on Wi-Fi. 3.Select the wireless network consistent with MiFi's SSID in the wireless network list. 4. Enter the correct password(Wi key). 5.Wait for a while, when Connected under the wireless network name, the wireless network connection is successful. b.IOS (Take Windows 7 as an example) 1. Make sure that MiFi is turned on normally. 2.Turn on the phone, select Settings

> Wi-Fi, and turn on Wi-Fi. 3.Select the wireless network consistent with MiFi's SSID in the wireless network list. 4.Enter the correct password(Wi key).> Wi-Fi, and turn on Wi-Fi. 5.Wait for a while, when Connected under the wireless network name, the wireless network connection is successful. Other terminal devices with Wi-Fi (such as iPad, tablet, Smart TV, etc.) can access the Internet through this device. For specic operations, please refer to the user manual of the terminal device. 8. LOG IN TO THE MANAGEMENT PAGE

(Take Windows 7, Google Chrome as an examples) 1. Make sure that the MiFi is properly connected to the computer. (PC can also be connected with USB data cable) 2. Open the web browser, enter 192.168.0.1 in the address bar and enter 3. Enter the user name and password to log in to the management page. The default user name is admin The default password is admin The webpage can view MiFi information and set and manage MiFi. a.Modify SSID and password 1. Select Settings > WiFi Settings >

Basic Settings. 2. Enter the Network Name

(SSID), Passwork, and click Apple to conrm. b.Modify the user name and password of the management page 1. Select Settings > Device Settings > Account Management. 2. Enter the New Username, New Passwork and click Apple to conrm . Please remember to modify the new user name and password. If you forget the password, you need to restore the factory settings of the device c.Factory reset If you forget some conguration parameters, you can choose to restore factory settings and recongure Mi. Set up via MiFi select Settings > Factory reset, select CONFIR Ser up via management page select Settings > Device Settings > Reset, select Reset After restoring the factory settings, the personal conguration parameters will be deleted and restored to the factory default values. If you forget the login user name or password on the management webpage, you can only restore factory settings through Mi. 9. MAKING AND RECEIVING CALLS Once your SIM cards are installed turn on your phone and wait a few minutes for your phone to nd a network. Then select the Phone Book icon. Here you can dial a number or select a contact from your stored contacts list to call. You can also view outgoing and incoming calls that have been made. 10. ANSWERING AND REJECTING CALLS To answer a call Click your nger to the Green Call Answer key. To reject a Call Click your nger to the Red Call End key. 11.SEND SMS Touch the SMS icon to s end an SMS to other mobile phone users, enter the phone number in the input eld, or select one of the contacts. Enter the content of the message and select Send. 12.SETTINGS To Change Settings:

Touch the Settings icon the Settings menu will open. Touch a category title to view further options. 1. Date and time To change the Date & Time Change the date display mode 2. Network APN Set device Network APN 3. Data roaming Turn data roaming on or o. 4.Mi hot settings Change the device hot name (SSID), password, etc. It can also be changed through the management page . 5.Factory reset Factory reset the device. As described in section 8-c, reset the device to factory settings. 6.Adobe device Displays information about your device. 13.TF CARD TF card is used to store more data, which can make MiFi transfer data like a U disk Inserting TF Card :

NB: Please ensure when inserting an SD card your phone is powered OFF Remove the battery cover and battery as described in section 4, put the TF card into the TF card holder, and buckle the card cover. Removing TF Card:

1. Turn o the device 2. Remove the battery cover and battery as described in section 4, Take out the TF card, and buckle the card cover. 14. HOW TO CONNECT TO A COMPUTER Turn on your phone before connecting the phone to a PC by USB cable. Use a USB cable to connect the phone with a computer. The phone will automatically detect a USB connection. 15. CARING FOR YOUR PHONE Your MiFi is a complex electronic device; think of it as a mini-computer. Here are a few tips to help you extend the life of your new device. Do not get your device wet. Even a small amount of moisture can damage your device and accessories. Protect your devices screen. Your devices screen is delicate. Use the original manufacturers batteries and accessories. Non-approved batteries and accessories can harm you and damage your device. Do not use damaged accessories. If your charger or any other accessory is damaged, please replace it. Do not attempt to charge your device if the charger has been dropped, received a sharp blow, or has been otherwise damaged; doing so may damage your device. 16. FCC RF EXPOSURE INFORMATION WARNINGRead this information before using your phone In August 1986 the Federal Communications CommissionFCC of the United States with its action in Report and Outer FCC 96-326 adopted an updated safety standard for human exposure to radio frequencyREelectromagnetic energy emitted by FCC regulated transmitters. Those guidelines are consistent with the safety standard previously set by both U.S. and international standards bodies. The design of this phone complies with the FCC guidelines and these international standards. Use only the supplied or an approved antenna. Unauthorized antennas modications, or attachments could impair call quality, damage the phone, or result in violation of FCC regulations. Do not use the phone with a damaged antenna. If a damaged antenna comes into contact with the skin, a minor burn may result. Please contact your local dealer for replacement antenna. BODY-WORN OPERATION:

This device was tested for typical body-worn operations with the back/front of the phone kept 1cm from the body. To comply with FCC RF exposure requirements, a minimum separation distance of 1cm must be maintained between the user's body and the back/front of the phone, including the antenna. Third-party belt-clips, holsters and similar accessories containing metallic components shall not be used. Body-worn accessories that cannot maintain 1cm separation distance between the use's body and the back/front of the phone, and have not been tested for typical body-worn operations may not comply with FCC RE exposure limits and should be avoided. For more information about RF exposure, please visit the FCC website at www.fcc.gov Your wireless handheld portable telephone is a low power radio transmitter and receiver. When it is ON, it receives and also sends out radio frequencyRFsignals. In August,1996,the Federal Communications CommissionsFCCadopted RF exposure guidelines with safety levels for hand-held wireless phones. Those guidelines are consistent with the safety standards previously set by both U.S. and international standards bodies:

<ANSIC95.1>1992/<NCRP Report 86>1986/

<ICNIRP>1999 Those standards were based on comprehensive and periodic evaluations of the relevant scientic literature. For example, over 120 scientists, engineers, and physicians from universities, government health agencies, and industry reviewed the available body of research to develop the ANSI StandardC95.1

.Nevertheless, we recommend that your use a hands-free kit with your phonesuch as an earpiece or headsetto avoid potential exposure to RF energy. The design of your phone complies with the FCC guidelinesand those standards. Use only the supplied or an approved replacement antenna. Unauthorized antennas, modications, or attachments could damage the phone and may violate FCC regulations. NORMAL POSITION:

Hold the phone as you would any other telephone with the antenna pointed up and over your shoulder. RF Exposure Information:

This product is compliance to FCC RF Exposure requirements and refers to FCC website https://apps.fcc.gov/oetcf/eas/reports/Ge-

nericSearch.cfm search for FCC ID:2AY6A-M1 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference.

(2)This device must accept any interference received, including interference that may cause undesired operation. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modications to this equipment. Such modications could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. Do not use the device with the environment which below minimum -10 or over maximum 40, the device may not work. Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

aapCl) Camm rm Clow M noaIL=

MODEL: Sky M1 FCCID: 2AY6A-M1 INPUT: 5V==1.0A Web IP: 192.168.0.1 Username: admin SSID: Sky_M1 FE SKY M) Password: admin Wifi Key: 1234567890 IMEI:357060076951105 SN:M12103010000001 CLOUD MOBILE MadeinChina 41.60mm 47.00mm

Cloud Mobile Holding LLC Agent Authorization Letter

(2021-05-13) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern:

We, the undersigned, hereby authorize Shenzhen NTEK Testing Technology Co., Ltd. 1/F, Building E, Fenda Science Park Sanwei, Xixiang, Bao'an District, Shenzhen, Guangdong, China Alex.li alex.li@ntek.org.cn to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Edgar Navarro / Manager Date/City:

Phone:

Fax:

E-mail:

2021-05-13 / LOS ANGELES 213-443-8197 N/A enavarro@truconnect.com

Cloud Mobile Holding LLC Long Term Confidentiality Request Letter

(2021-05-13) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: CONFIDENTIALITY REQUEST FOR Product: 4G MIFI Model No.: Sky M1 FCC ID: 2AY6A-M1 To Whom It May Concern:

This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the Schematic Diagram Block Diagram Part List / BOM List / PCB Layout Operational Description Tune-up Procedure FCC Software Security Requirements for UNII devices Required to be submitted with this application be permanently withheld from public review. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Please contact me if there is any information you may need. Sincerely, Edgar Navarro / Manager Date/City:

Phone:

Fax:

E-mail:

2021-05-13 / LOS ANGELES 213-443-8197 N/A enavarro@truconnect.com

Cloud Mobile Holding LLC Short Term Confidentiality Request Letter

(2021-05-13) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Short Term Confidentiality Request For Product: 4G MIFI Model No.: Sky M1 FCC ID: 2AY6A-M1 To Whom It May Concern:

In accordance with sections 0.457 and 0.459 of CFR 47, < Cloud Mobile Holding LLC >. requests short-term Confidentiality of following sections of this application for a period of 180 days after grant is issued. Test setup photos External photos Internal photos Users manual These documents contain detailed system and equipment descriptions and related information about the product, which < Cloud Mobile Holding LLC > considers to be proprietary, confidential, and a custom design and otherwise, would not release to the general public. Since this design is a basis from which future technological products will evolve, < Cloud Mobile Holding LLC > feels that this information would be of benefit to its competitors, and that the disclosure of the information in these documents would give our competitors an unfair advantage in the market. Please contact me if there is any information you may need. Sincerely, Edgar Navarro / Manager Date/City:

Phone:

Fax:

E-mail:

2021-05-13 / LOS ANGELES 213-443-8197 N/A enavarro@truconnect.com