Establishing a Bluetooth Connection Charging Status LED The CR2600 Mountable Palm Cart Charger has an LED to indicate the charging status of reader. Press either trigger button on the CR2600 and scan the QuickConnect barcode located on the Mountable Palm Cart Charger to establish a Bluetooth connection between the CR2600 and the computer that the Charger is connected to. (Figure 5) Figure 5 Trigger Buttons CodeXML Modem Status LED Charging Status LED A red LED = reader/battery is charging A green LED = reader/battery is fully charged*
*Note: In certain reader configurations, the radio is required to always be on, therefore requiring a constant power draw. In these instances, while the power draw is minimal, the LED light may never turn green when charging a battery attached to a reader. Once connected, the reader will beep once as confirmation and the modems blue LED light will become solid (Figure 6). If the reader does not connect, the reader will beep four times in rapid succession. Charging a CR2600 Charging Status LED Figure 8 Keyboard Input (USB) Figure 6 The modem is defaulted to English language keyboards. If you need to communicate in a different language requiring a change in keyboard settings, please scan the appropriate configuration barcode below, after connecting to the modem:
English (Default) Universal French German Place a CR2600 into the charging bay of the Mountable Palm Cart Charger, facing forward, and down (Figure 7), making sure it is seated firmly into place. Once the charging clips have made contact with the connectors on the reader the charging status LED will light up. Note: Battery ships with approximately 50% battery life. Fully charge battery before use. Approximate charge time is 4 hours. Japanese Non-printable ASCII Keyboard
(No Leading 0) Non-printable ASCII Keyboard (Crtl + character) Figure 7 2 Refer to CR2600 Quick Start Guide and Product Manual for reader specifications. 3 Page Button Quickstart Guide Page Button CR2600 Mountable Palm Cart Charger The CR2600 Mountable Palm Cart Charger is equipped with a page button. To locate a CR2600 that has a connection established to the modem, and is within Bluetooth range, simply press the Page button on the Charger. The reader will then beep. Important Note:
The Code Reader 2600 (CR2600) has been tested for compliance with FCC regulations and was found to be compliant with all applicable FCC Rules and Regulations. FCC ID: QQ6-BTA01 IC ID: 9966A-BTA01 Model #: CRA-A111_01 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by manufacturer could void the users authority to operate the equipment. IMPORTANT! Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes: (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, meme si le brouillage est susceptible den compromettre le fonctionnement. IMPORTANT! Tous les changements ou modifications pas expressment approuvs par la partie responsable de la conformit ont pu vider lautorit de lutilisateur pour actioner cet quipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. This Class [B] digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe [B] est conforme la norme NMB-003 du Canada US Patent: www.codecorp.com/legal/patents.php Operating Temperature: -20 to 55 C / -4 to 131 F The CR2600 Mountable Palm Cart Charger is designed for easy mobile cart integration. The embedded CodeXML Modem enables a CR2600 reader to wirelessly transmit, through a Bluetooth connection, data to a host device. In addition, the Mountable Palm Cart Charger charges a wireless palm CR2600 while positioning it within easy reach for retrieval. Figure 1 Included Note: Two M4 Phillips pan head X 6mm threaded length screws are included for installation. CR2600 Mountable Palm Cart Charger Micro-USB to USB Cable Installation Attach the micro-USB cable provided to the CR2600 Mountable Palm Cart Charger (Figure 2), and plug the USB connector into the USB port on the computer (Figure 3). Once plugged in the charging status LED will flash red (Figure 6). Figure 2 Figure 3 Figure 4 Two M4 Phillips pan head screws are included with each CRA-A111. The screws are designed to fit into the threaded brass inserts (Figure 4) found on the back of the charger. Insert and tighten the screws prior to, or after they are in the position to the mounting bracket. Once mounted, tighten each screw to ensure the charger is securely attached to the mounting bracket. 4 www.codecorp.com 2014. Code Corporation. All Rights Reserved. C008950_01_A111_QuickStart_Guide