FCC ID: TXH-50165 50165

Revision:

Date:

Model:

Trademark:

Rev04 2022/01/10 50165 COGNEX 5 5 5 Wireless Module 50165 Integration Manual 1 Description:

General The 50165 wireless module is designed based on B-Link BL-M3455AT1(BL-6255) using a Cypress CYW43455 chipset. It operates in 2.4GHz band for BT classic/ BT LE and WiFi and in the 5GHz band for Wifi. The module supports standard SDIO v3.0 interfaces, backward compatible with SDIO v2.0 and supports a high-speed UART interface. Front Side With Shield Front Side Without Shield Back Side Cognex Corporation One Vision Drive Natick, MA 01760-2059 (508) 650-3000 fax (508) 650-3333 www.cognex.com The module uses a PCB antenna that provides with max 3.4 dBi gain in the frequency range from 2412-2472 MHz and 5.18-5.835GHz. Features Supports with SDIO2.0/3.0;

Supports a high-speed UART interface for Bluetooth 4.1 Supports IEEE 802.11a/b/g/n/ac Operating frequencies: 2.4~2.4835GHz & 5.18-5.835GHz Build in PCB Antenna with 3.4 dBi gain Applications Cognex DM8700 series Handheld Readers Cognex DM8700 series Base Stations 2 Functional Block Diagram The 50165 has two crystals. One 32.768 kHz low power oscillator for low power mode timing and one 37.4 MHz reference clock. Via the connector the module is powered with 5VDC and internally 3.3VDC are generated and filtered. The wireless connectivity is based on the B-Link BL-

M3455AT1(BL-6255) chip. Cognex Corporation One Vision Drive Natick, MA 01760-2059 (508) 650-3000 fax (508) 650-3333 www.cognex.com 3 Antenna Specification Function

+5V

+5V

+5V SDIO_D0 UART_CTS SDIO_D1 UART1_RXD SDIO_D2 UART1_TXD SDIO_D3 UART_RTS SDIO_CMD I2C_SDA SDIO_CLK I2C_SCL WAKE GND GND GND GND 4 Pin Assignments Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Description Main power source input Main power source input Main power source input SDIO Interface UART Interface SDIO Interface UART Interface SDIO Interface UART Interface SDIO Interface UART Interface SDIO Interface I2C interface SDIO Interface I2C interface Module wake-up host Ground Ground Ground Ground Cognex Corporation One Vision Drive Natick, MA 01760-2059 (508) 650-3000 fax (508) 650-3333 www.cognex.com 5 Application Information Supported Platforms:

Cognex products using Linux based operating systems based on ARM CPU framework. Integration Information:

UART 50165 provides with a high-speed 4-wire CTS/RTS UART interface. It is compatible with the industry standard 16550 UART. SDIO 50165 provides support for SDIO version 3.0, including the new UHS-I modes:

DS: Default speed (DS) up to 25 MHz, including 1- and 4-bit modes (3.3 V signaling). HS: High speed up to 50 MHz (3.3 V signaling). Mechanical For integration in Cognex Handheld Readers keep a minimum clearance of 1.6mm and a maximum clearance of 2mm between outer round shape of the module and Readers main plastic housing. Main housing thickness should be 3.7 +/-1mm For integration in Cognex Base Stations use part number 1000001866 underneath the 50165 Cognex Corporation One Vision Drive Natick, MA 01760-2059 (508) 650-3000 fax (508) 650-3333 www.cognex.com Label Wireless chipset Or at least a similar supporting structure underneath the module in the same shape made of Makrolon 2405 and 4.9 +/- 0.1mm thickness. Labeling The module is labeled with FCC ID, IC ID and model name:

Integrators have to label End-devices with:

Contains FCC ID: TXH-50165;

IC: 6315A-50165 Labeling shall be clear and legible and shall resist the effects of the cleaning agents specified by the End-device Manual. Warnings:

FCC 15.19 Labelling requirements This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. FCC 15.21 Information to user Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Cognex Corporation One Vision Drive Natick, MA 01760-2059 (508) 650-3000 fax (508) 650-3333 www.cognex.com FCC RF Exposure:

To comply with FCC RF exposure requirements, a minimum separation distance of 35mm must be maintained between the user's hand and the integral antenna of the device during normal handling of the device. For more information about RF exposure, please visit the FCC website at www.fcc.gov ISED Statements (Canada) Le prsent appareil est conforme aux Innovation, Science and Economic Development Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. ESD CAUTION: Although this module is designed to be as robust as possible, Electrostatic Discharge (ESD) can damage this module. It must be protected from ESD at all times and handled under the protectionof ESD. Cognex Corporation One Vision Drive Natick, MA 01760-2059 (508) 650-3000 fax (508) 650-3333 www.cognex.com

Labeling The module is labeled with FCC ID, IC ID and model name:

Wireless chipset Label Foc 10 TxH-50164 Ici 63154-50164 Model: so16s Integrators have to label End-devices with:

Contains FCC ID: TXH-50164;

IC: 6315A-50164 Labeling shall be clear and legible and shall resist the effects of the cleaning agents specified by the End-device Manual.

Imad Hjije, Abdellah Ahakki, Teoman Soner-Sunar(1) 7layers GmbH Borsigstr. 11 40880 Ratingen Germany Cognex Germany Aachen GmbH Krefelder Strasse 218 52070 Aachen Germany FCC AGENCY AUTHORIZATION LETTER We Name:

Address:

City:

Country:

Declare that:

Name Representative of agent:

Agent Company name:

Address:

City:

Country is authorized to apply for Certification of the following product(s):

Product description: Wireless module for Cognex industrial vision systems. Type designation:

Trademark:

on our behalf. Date:

City:

Name:

Function:

Signature:

Notes:

(1): Required for FCC application

(2): For FCC it must be the Grantee Code owner or the authorized agent. Principal Compliance Engineer

. 50165 COGNEX Simon Jnger (2) 08.06.2021 Aachen Cognex Corporation One Vision Drive Natick, MA 01760-2059 (508) 650-3000 fax (508) 650-3333 www.cognex.com

RF_734_02 04 April 16 Modular Approval Request FCC (KDB 996369 D01 & Part 15.212) FCC ID: TXH-50165 Items to be covered by Single modular transmitters. 1. The modular transmitter must have its own RF shielding. Answer from applicant Yes 2. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. 3. The modular transmitter must have its own power supply regulation. 4. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(b)(c). The antenna must either be permanently attached or employ a unique antenna coupler (at all connections between the module and the antenna, including the cable). 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the Yes module must not be inside another device during testing. This is intended to demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. 6. The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number in accordance with 15.212 (a)(1)(vi)(A) / (B). 8. 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. For example, there are very strict operational and timing requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. The modular transmitter must comply with any applicable RF exposure requirements. For example, FCC Rules in Sections 1.1310, 2.1091, 2.1093, and specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance. Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. Yes Yes Yes Yes Yes Yes RF_734_02 04 April 16 Answer from applicant Items to be covered by Split modular transmitters. 1. The modular transmitter must comply with all requirements of a single modular transmitter except for items (1) & (5) of the above single modular approval requirements. 2. Only the radio front end must be shielded. The physical crystal and tuning capacitors may be located external to the shielded radio elements. The interface between the split sections of the modular system must be digital with a minimum signalling amplitude of 150 mV peak-to-peak. 3. Control information and other data may be exchanged between the transmitter control elements and radio front end. 4. The sections of a split modular transmitter must be tested installed in a host device(s) similar to that which is representative of the platform(s) intended for use. 5. Manufacturers must ensure that only transmitter control elements and radio front end components that have been approved together are capable of operating together. The transmitter module must not operate unless it has verified that the installed transmitter control elements and radio front end have been authorized together. Manufacturers may use means including, but not limited to, coding in hardware and electronic signatures in software to meet these requirements, and must describe the methods in their application for equipment authorization. Note: A limited modular approval (LMA) may be granted for single or split modular transmitters that comply partially with the requirements above. Name and surname of applicant (or authorized representative): Imad Hjije Date: 08/17/2021 Signature:

FCC, Request for non-disclosure RF_501, Issue 8 Date: 21-Nov-2018 Page 1 of 1 Company Name: Cognex Germany Aachen GmbH Address:

City:

Country:

Krefelder Strasse 218 Aachen Germany Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands To: Telefication B.V., Dept. FCC TCB Subject: Request for confidentiality FCC ID: TXH-50165 Reference number: ######

Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application:

Bill(s) of Material Block Diagrams Operational Description Schematic Diagrams Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commissions policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, applicant hereby requests Short-Term Confidential treatment of the following materials (See notes below):

Internal Photos Users Manual Test Set-up Photos External Photos Justification: Protection from competitors Name and signature of applicant: Imad Hjije Date: 08/17/2020 Notes:

1) A document or type of document can only have ONE type of confidentiality!

2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)!

The planned date should stated in the RF731 application form. 3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this!

5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period