FCC ID: 2BAVP-WT60A 5.8GHz Audio Tactile Transmitter

4D Tactile Transducer System 4DS101DG For KRATOS | ASHUR Gaming Chair DO NOT expose the system to extreme temperatures. To prevent the battery from exploding, DO NOT place the system near heat sources or re. Only clean the system using a soft, dry cloth. The system IS NOT waterproof. DO NOT store or use the system close to places that contain or are exposed to raindrops, coee, water, perspiration, steam, or exces-

sive humidity. To avoid interference, bad reception, or transmission loss of the wireless system, DO NOT store or use the system near a magnetic device. Only use a voltage appropriate for the power adapter supplied with the package. Higher voltages may cause re, electrical shock, or otherwise destroy the system. DO NOT attempt to repair, reassemble, or disassemble the system or even remove the guarantee sticker! These actions will void the warranty and all associated cover-

ages. To replace the lithium-ion battery, only use a certied battery pack from the manufacturer and strictly adhere to the instructions highlighted in this guide. 4DS101-DG Standard, LI-ION Battery-Powered Tactile Transducer System 4DS101-DGS Advanced, Add Stereo Speakers 4DS101-DGST Advanced, Add Stereo Speakers and Bluetooth Transmitter What's in the Package Universal Power Adapter Input AC100V-240V Output DC19 V1.89A User Guide 4D Tactile Transducer System 4DS101DG Battery Charge & Status Level and Volume Control DC Charge Port: Certified DC19V Adapter only Transducer Haptic Control Knob LED Charge Indicator: RED blinking- Charging Music Volume Control Knob LED Battery Status Indicators:

75%+ charge 50% to 75% charge 25% to 50% charge Below 25% charge Headset Jack Audio Input Mode Selection:

Press for 1 second to switch to the next mode. Power and Logo RGB strip ARGB: Logo strip color switch button

(limited models only) Power ON button: Blue light when on Antenna Area: Do not block with any object to avoid bad reception Sequential order:

Bluetooth >

Tactile Transmitter> Auxiliary The default preset is Bluetooth. The system will memorize the previously used preset. PAIR Button:

The white LED light on the top of the PAIR button will blink when switched to Tactile Transmitter Mode. A long press of 3 seconds on the PAIR button will make the system enter pairing status. Refer to the Basic Operation section for details on transmitter pairing. AUX1/8" Auxiliary jack. Battery and Charge The 4DS101 system is powered by a lithium-ion rechargeable battery installed in the chair seat. Ensure that this battery pack is fully charged before first use. Use the certified 19VDC power adapter supplied with the package at all times. When charging the battery, the LED indicator displays a blinking RED light. When fully charged, the RED light will be turned off, and four GREEN LED indicators will light up. If only one GREEN LED indicator is lit up, the system will need to be charged as soon as possible It is possible to use the 4DS101 system when the control unit is connected to the power adapter. The battery pack can be recharged at any time; it DOES NOT have to be completely discharged before charging. Keeping the battery charged and used periodically will increase its performance and lifetime. Repeated full battery discharges must be AVOIDED. Connecting to Audio Source Bluetooth Mode Headphone Bluetooth Transmitter Bluetooth Headset AR/VR Gears Game Consoles Auxiliary Mode Headphone AR/VR Gears Connecting to Audio Source Tactile Transmitter (TT) Mode Amplier Set-Top-BOX Game consoles TV PRE out Subwoofer Audio out Audio out Optical Connector PC Laptop MIC Audio out MIC Audio WT60A Tactile Transmitter The white LED will light on when switched into Tactile Transmitter Mode Basic Operations Turn the System ON Plug a headset into the headphone jack. If you are using Bluetooth headphones and connecting to model 4DS101-DGST's embedded Bluetooth transmitter, the system will need to be turned on rst. The battery status LEDs will display the current power when the system is switched on. Choose the Input Source The 4DS101 system oers 3 modes:

Bluetooth, Tactile Transmitter (TT), and Auxiliary. Pressing the SEL button for 1 second will switch to the next mode sequentially. The system will issue a sound corresponding to each mode accordingly. 5 to pair to Bluetooth For Bluetooth Mode, the audio source needs ID

"KRATOS". If the Bluetooth ID does not appear, please turn o the Bluetooth mode and turn it back on to search for the ID. Since Bluetooth can only connect to one device at a time, any pre-existing the Bluetooth device will need to be withdrawn to allow the audio source to connect to the 4DS101. connections to Push and lock the ON button.When the power is switched on, the blue LED will light up, and the system will make a

"KRATOS Activated" sound. 6 When entering Tactile Transmitter mode, the LED light on top of the PAIR button will blink. Once the Tactile Transmitter WT60A turns on, the LED light will display a constant white light, which that pairing and linking were successful. Remember that the 4DS101 must be paired with the Tactile Transmitter before its rst use. indicates 7 When entering Auxiliary Mode, please connect the audio source to the 4DS101 via a 1/8" mini plug. Basic Operations Volume Adjustment Use the HAPTIC knob to adjust the haptic level of the transducers. Use the HEADSET knob to adjust the music volume. The phone jack supports TRRS headsets. It is recommended to set the input source volume to a high level and use the knobs to adjust the volume to a suitable level. Power and Protection If you plan to use the 4DS101 system for a long session, you can plug in the DC power adapter to simultane-

ously play and charge. If the 4DS101's control unit experiences overheating or excessive current, the in-built protection system will automat-

ically turn it o. Once this occurs, you need to switch o the power button and plug in the DC power adapter for 2-3 minutes before turning the system's control unit on again. Pairing with Tactile Transmitter WT60A Note Tactile Transmitter mode will receive audio from the WT60A Tactile Transmitter. This transmitter needs to be purchased separately. Turn the power on in the control units of both the 4DS101 and WT60A. Switch to Tactile Transmitter Mode on the 4DS101 system. Press the PAIR button for 3 seconds. The white LED light will blink, and a beeping sound will follow. Press the PAIR button for 5 seconds. The logo light on the front panel of the transmitter will blink to indicate that pairing mode has been entered. Once the LEDs stop blinking and are constantly lit, the pairing is complete, and the link is ready. Trademark & Warranty 4DS, KRATOS, ASHUR, and COLINSE are exclusively registered trademarks of Colinse Inc. worldwide. All other trademarks stated in this Guide are properties of the respective owners. The 4DS101 system has a one-year warranty against manufacturing or material defects from the purchase date. However, this restricted warranty is considered void under any of the conditions below;

The system/product is destroyed or damaged by improper operation, accident, negligence, unreasonable use, misuse, or other causes. The warranty sticker or serial number tag is removed or altered. The system/product is tampered with or modied. This product's warranty covers the Control Unit of the 4DS101 System, WT60A Transmitter, Power Adapters, Lithium Battery Pack, and Transducers. Colinse worldwide will be responsible for repairing the system at no cost within the warranty team

(support@colinse.com) or the local reseller for further information about the warranty. customer support contact period. Kindly the Limited Liability Colinse will not under any circumstances be liable for any damages whatsoever, including any special, indirect, incidental, consequential, or exemplary damages resulting from the use or loss of use of the product, due to any cause, even if Colinse has been advised of the possibility of such damages. In any event, Colinse's total liability to you for all damages (Whether based on contract, tort, or other theories) will be limited to the amount you actually paid for the product during the month in question. Some states and jurisdictions do not allow the limitation or exclusion of liability for incidental or consequential damages, so the above limitation may not apply to you. Troubleshooting The system does not work after being powered on. A. B. C. D. Check whether the battery status lights are on or o. If all are o, charge the battery ASAP. Check whether the input source has successfully linked with the 4DS101 system. Is the volume of the source too low?

Adjust the headphone/haptic knobs to higher levels. Reopen the control unit. The Bluetooth ID does not appear on the device. A. Conrm that the 4DS101 is in Bluetooth mode. B. Check whether another device has overridden the Bluetooth link. C. Switch o the devices Bluetooth button and switch it on again to search. D. Turn o the 4DS101 control unit and turn it on again to search for the Bluetooth ID. No response in Tactile Transmitter mode. A. B. C. Check whether the LED light is a constant white light. A blinking light indicates that the pairing has been unsuccessful. Check whether the transmitter has connected to the audio source and whether the switch is in the correct position. Check whether the source volume of the transmitter is too low. Battery Charging - All green LED lights are o after plugging in the power adapter. If the battery has been fully discharged, the Green LED lights will begin lighting up sequentially after 1 hour when their respective voltage levels are reached. A blinking red light means that the battery is charging. Battery Charging Red LED charging light is not blinking when charging. Make sure to use the certied power adapter supplied with the package. It is possible to damage or burn the control unit if power adapters from other brands are used or the wrong input voltage is applied. System turns o suddenly. A. Check whether the battery charge level is too low (one green LED light only). Charge the battery immediately if the battery is low. B. If the system experiences overheating or excessive current, the in-built protection system will automatically turn it o. Once this occurs, you need to switch o the power button and plug in the DC power adapter for 2-3 minutes before turning the system's control unit on again. Contact customer service (support@colinse.com) if the above steps do not solve your problem. 7 Product Specications System Placement Material Control Unit in Right side of Seat Transducers Installed in Seat and Backrest Battery Pack Installed in Bottom of Seat Aluminum Alloy Tactile Transducer TTD100A Power Output Frequency Range Nominal Impedance Peak 100W, RMS 50W 20Hz ~ 120 Hz 4 Audio System Audio Connectivity Headset Connectivity Control Knobs Power System- 4DS101 Battery Connectivity Battery Pack Battery Charging Tactile Transmitter Bluetooth 5.0 + EDR AUX, 1/8-inch (3.5mm) Jack Output 1/8-inch (3.5mm) Jack, TRRS Haptic Level and Headphone Volume Rechargeable Lithium-ION Battery 14.8V 5200mAh, 4Hours Charging Time DC19V1.89A Universal Power Adapter Input 100-240VAC, 50-60Hz Wireless Audio System WT60A Operating Frequency Latency Receiving Range Audio Input Additional Output Power Input 5740 - 5840 MHz 5.8 ms 32-48FT (10-15m), Line-of-Sight 1/8-inch (3.5mm) Stereo Jack Optical S/PDIF Jack 1/8-inch (3.5mm) Jack DC5V2A Micro USB Connection Product Warranty Card 4DS101 Tactile Transducer System 4DS101DG/4DS101DGS/4DS101DGST The warranty of this product covers the Control Unit of 4DS101, WT60A Tactile Transmitter, Power Adapter, Lithium Battery, and Transducers. This warranty does not apply to product failure caused by accidents, abuse, mishandling, improper installation, alterations, act of nature, improper usage, or problems with electrical power. Disassemble, repair, reassemble the device , or remove the warranty sticker, any of these actions will void the warranty and any FCC Caution:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCCs RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.

Page 1 of 1 FCC ID: 2BAVP-WT60A LABEL AND LOCATION 5.8GHz Audio Tactile Transmitter Model: WT60A FCC ID: 2BAVP-WT60A

(Size: L3.5cm x 6.5cm) Label Location Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: webmaster@lcs-cert.com | Web: www.lcs-cert.com Scan code to check authenticity

COLINSE INC Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 U.S. Agent Designation 5/4/2023 COLINSE INC acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought (FCC ID:

2BAVP-WT60A):

Contact Name: Tim Payne Company of U.S. agent: FCC US Agent, LLC Physical U.S. address of agent: 3722 Illinois Avenue, Saint Charles, IL, 60174, USA FRN of U.S. agent: 0033402884 Email address of U.S. agent: Support@FCCUSAgent.com FCC US Agent, LLC acknowledges their obligation to accept service of process on behalf of COLINSE INC. COLINSE INC with the FRN 0033667973 accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under 2.911(d)(7). Sincerely, Signature Albert Lin C.E.O. COLINSE INC 4 0 V

, U

) 7

) d

1 1 9

. 2 _ t n e g A _ S U

l e d o m

_ 8 4 Signature Tim Payne Manager FCC US Agent, LLC The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB.

Confidentiality Request Letter For Certification Service in the USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 To whom it may concern Pursuant to Paragraphs 0.457 and 0.459 of the Commissions Rules (47 C.F.R.) and Section 552(b)(4) of the Freedom of Information Act, we request confidentiality for the documentation of the following products:

FCC ID 2BAVP-WT60A Model name WT60A, WT60C, brio600 For the products listed above, we request permanent confidentiality for all applicable exhibits as there are:

the Operational Description the Block Diagram the Schematics the Parts Lists the Tune Up Information The above listed exhibits contain trade secrets and proprietary information that could be of benefit to our competitors. If you have any questions, please feel free to contact us at the address shown below. Sincerely, 2023-05-15 Signature Date Printed Name of Signee: Albert Lin Company: COLINSE INC Address: Floor C, 2 Zhong-yang 1st Street, Xindian New Taipei, Taiwan, China Phone: +886-2-2185272 Email: 3005232849@qq.com Fax: N/A

Covered Equipment Identification Letter For Certification Service in the USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 To whom it may concern Pursuant to Section 2.911(d)(5)(ii) of the Commissions Rules (47 C.F.R.) we attest as follows:

We, applicant Company Name: COLINSE INC Address:

Floor C, 2 Zhong-yang 1st Street, Xindian New Taipei, Taiwan, China Phone: +886-2-2185272 certify that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. If you have any questions, please feel free to contact us at the address shown below. Sincerely, 2023-05-15 Signature Date Printed Name of Signee: Albert Lin Company: COLINSE INC Address: Floor C, 2 Zhong-yang 1st Street, Xindian New Taipei, Taiwan, China Phone: +886-2-2185272 Email: 3005232849@qq.com Fax: N/A

Covered Equipment Attestation Letter For Certification Service in the USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 To whom it may concern Pursuant to Section 2.911(d)(5)(i)-(ii) of the Commissions Rules (47 C.F.R.) we attest as follows for the product listed below:

FCC ID 2BAVP-WT60A We, applicant Model name WT60A, WT60C, brio600 Company Name: COLINSE INC Address:

Floor C, 2 Zhong-yang 1st Street, Xindian New Taipei, Taiwan, China Phone: +886-2-2185272 certify that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. If you have any questions, please feel free to contact us at the address shown below. Sincerely, 2023-05-15 Signature Date Printed Name of Signee: Albert Lin Company: COLINSE INC Address: Floor C, 2 Zhong-yang 1st Street, Xindian New Taipei, Taiwan, China Phone: +886-2-2185272 Email: 3005232849@qq.com Fax: N/A

COLINSE INC Floor C, 2 Zhong-yang 1st Street, Xindian New Taipei, Taiwan, China Date: May 15, 2023 FCC ID: 2BAVP-WT60A Model Number: WT60A, WT60C, brio600 To: Federal Communication Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21048 To Whom It May Concern, We, COLINSE INC hereby declare that our product (5.8GHz Audio Tactile Transmitter) Model Number: WT60A, WT60C, brio600 board, Schematic, Hardware version, Software version, structure and internal photos are same, named differently due to marketing purposes. Should you have any questions or comments regarding this matter, please have my best attention. Sincerely,

(Signed) Name/Title: Albert Lin/ CEO Company: COLINSE INC Address: Floor C, 2 Zhong-yang 1st Street, Xindian New Taipei, Taiwan, China Tel: +886-2-2185272 Fax: n/a E-Mail: 3005232849@qq.com