FCC ID: 2ANSR-CM96201FR Smart Video Doorbell

ENJOY THE SMART LIFE F U L L M A N U A L K I T V I S T O W I - F I S m a r t V i d e o D o o r b e l l Passion.Technology.Design. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. IC STATEMENT This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil contient des metteurs / rcepteurs exempts de licence conformes aux RSS (RSS) d'Innovation, Sciences et Dveloppement conomique Canada. Le fonctionnement est soumis aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre 3 le fonctionnement. EN Congratulations on your purchase of the KitVisto2 by Comelit!

Comelit Group S.p.A. is an innovative company that combines cutting edge production technologies with carefully selected materials and meticulous attention to detail to create a product that is extremely reliable and sturdy. Observe the indications given in this manual to ensure the correct installation and use of the product. This document may not be reproduced, even in part, without the express written consent of Comelit Group S.p.A. The brands and commercial names appearing in this publication remain the property of their respective owners. Comelit Group S.p.A. nonetheless reserves the right to change or update the information provided in this manual at any time and without prior notice. We recommend that you visit the websites www.comelitgroup.com and www.vistodoorbell.com to be sure of obtaining the most up-to-date information. The Comelit Visto application is available on App Store and Google Play and is supported by devices with iOS 8.0 (or later) and by the most common Android devices with Android version 4.4 or higher, however some functionalities may be limited depending on the model and the version. KitVisto2 With Visto2 Kit you can control your video entry system both locally and remotely. With the Comelit Visto app, available on App Store and Google Play, you can answer calls from an external unit, view images from the camera on the external unit, images from additional remote cameras and operate the locks of doors and gates. In addition, thanks to the integral motion detector function, you can receive on your smartphone notification of any movement/presence detected around your front door. 5 EN 5 ") m (1 , 8 7 m 4 28 m m(1,10") Visto2 5 ") m (1 , 8 7 m 4 28 m 1 m(1,10") 2

)

"

9 3 5

,

(

m m 7 3 1 4

)

"

9 3 5

,

(

m m 7 3 1 3 2 1 6 5 ") m (1 , 8 7 m 4 5 28 m m(1,10") 6 7

)

"

9 3

, 5

(

m m 7 3 1 8 9 10 11 12 Mounting instructions on page 42 1. Fixing hole for accessories art. 3525, art. 3526 (Optional) 2. Surface mount by means of screws 3. Cable inlet hole 4. Connection terminal

+ - Visto2 power supply NO Normally open relay contact COM Common relay contact 5. Brightness sensor 6. Wide-angle color camera 7. Microphone 8. Interchangeable cover

(Mounting instructions on page 41) 9. Call button / Indicator LED 10. Loudspeaker 11. Reset. To restore factory settings 12. Mounting screw EN Chime 3524 Mounting instructions on page 43 1 7 3 m m

( 6 , 8 " ) 1 Chime for KitVisto2 with integrated Wi-Fi and with Ethernet port for connecting to the router as an alternative to the Wi-

Fi connection. Surface-mounted, 3 screws and 3 wall-plugs provided. You can select 4 different pre-stored melodies; melody selection and volume adjustment are possible via the Comelit Visto app. 4 7 m

(1,8 m 5")

)

"

3

, 4

(

m m 0 1 1 2 8

)

"

3

, 4

(

m m 0 1 1 3 4 5 2 2 7 6 Power supply 12-24 VAC 1. Cover 2. Wall fixing screw holes 3. RJ45 input for cable connection to the router 4. Cable inlet hole 5. Terminal block Visto2 Front Power/data output VF- VF+

( 6 , 8 " ) VR- VR+ Visto2 Rear Power/data output 1 7 3 m m 4 7 m

(1,8 m 5") F COM R Power supply input 12-24 VAC from transformer Front pushbutton input Pushbuttons common contact Rear pushbutton input 6. System restart 7. Reset Wi-Fi configuration 8. Loudspeaker 7 EN It is advisable to install the Chime 3524 near the Wi-Fi router. Always check the quality of the Wi-Fi signal before final installation of the product. If your Wi-Fi signal is not strong enough, it can effect the video and audio quality and operation of the KitVisto2; in this case we recommend to connect the art. 3424 to the router via the Ethernet cable. Wiring diagrams from page 44 Maximum connection distances A B 8 Art. 3524 VISTO2 EN LED guide LED guide Start Confirmation of door opening Searching for a network Network not available Loss of network connection Connected to Chime 3524 Not connected to the server Standby mode Call in progress Conversation in progress Updating in progress... WARNING: this update can take up to 10 minutes, DO NOT remove the power during this process. Chime 3524 Power supply Wi-Fi LED Front Visto2 LED Rear Visto2 LED A B C D C D A B 9 EN Visto2 Kit After downloading the COMELIT VISTO app from the store onto your smartphone, you can use the app to connect the KitVisto2 to your router via Wi-Fi or cable. If your router is connected to the internet then your Smartphone will receive a push notification for motion detection notification and can communicate between the Visto2 Kit and your smartphone. The Visto2 Kit supports 433.92 MHZ radio frequency signal, which can transmit the signal and can remotely control any products that can receive the same frequency. The Wi-Fi and 433.92 MHZ radio frequency signal on KitVisto2 are two independent signals and works independently. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This device must be installed to provide a separation distance of at least 20 cm from all persons, and must not be collocated or operating in conjunction with any other antenna or transmitter. App Comelit Visto Getting started with KitVisto2 and app 1. Download the COMELIT VISTO app from Apple App Store or Google Play 2. Open the app and press SIGN UP 3. Enter the data requested to create an account 4. Confirm the account from your e-mail 5. From the app, press LOGIN 6. Enter your username and password press LOGIN 7. Add Visto2 Kit by clicking 8. Follow the instructions of the app wizard to complete setup and pressing CONNECT NEW DEVICE Useful tips during the first installation of the app from page 48 10 EN Art. 3527W, Art. 3527S 2 1 3 41 Art. Visto 1 3 42 1 2 C F P2 C F P1 L L 3 1 2

)

"

4 6

(

m c 3 6 1

)

"

1 5

(

m c 0 3 1 1 3 2 2 4 Art. 3524 3 2 1 1 2 3 4 REMOVAL 43 Wi-Fi connection between art. 3524 and router Connessione Wi-Fi tra art. 3524 e router Connexion entre lart. 3524 et le routeur par Wi-Fi Aansluiting tussen art. 3524 en router via Wi-Fi Verbindung Art. 3524 und Router ber WLAN Conexin entre el art. 3524 y el router mediante Wi-Fi 110/220V 12-24V AC APP INTERNET ROUTER art. 3524

+

F V

-

F V

+

R V

-

R V R M O FC 44

+ - NO C VISTO2 Ethernet connection between art. 3524 and router Connessione LAN ethernet tra art. 3524 e router Connexion entre lart. 3524 et le routeur par cble Ethernet Aansluiting tussen art. 3524 en router via ethernetkabel Verbindung Art. 3524 und Router ber Patchkabel (Ethernet) Conexin entre el art. 3524 y el router mediante cable Ethernet 110/220V 12-24V AC APP INTERNET ROUTER art. 3524 Ethernet

+

F V

-

F V

+

R V

-

R V R M O FC

+ - NO C VISTO2 45 Maximum system expansion Massima espansione dimpianto Maximale systeemuitbreiding Maximale Anlagenerweiterung Extension maximale de linstallation Mxima expansin de la instalacin 110/220V 12-24V AC

+

F V

-

F V

+

R V

-

R V R M O FC ROUTER INTERNET APP

+ - NO C

+ - NO C VISTO2 FRONT VISTO2 REAR PUSH BUTTON 1 PUSH BUTTON 2 46 Variant for electric lock connection Variante per la serratura elettrica Uitvoering met elektrisch slot Variant fr Elektrische Verriegelung Variant pour connection dun verrou lectrique Variante para conexion de cerradura electrica 110/220V 12-24V AC/DC

+ -

NO C VISTO2 max 1A 47 PRO INSTALLATION TIPS During the configuration you will be asked to know the DEVICE PASSWORD, use 888888. Durante la configurazione vi verr chiesto di conoscere la PASSWORD DEL DISPOSITIVO, inserire 888888 Durant linstallation, il vous sera ncessaire de saisir le MOT DE PASSE DU DISPOSITIF

: 888888 Tijdens de configuratie wordt u verzocht om het WACHTWOORD VAN HET APPARAAT, voer dan 888888 in Bei der Konfiguration werden Sie zur Eingabe des GERTE-PASSWORTS aufgefordert;

geben Sie 888888 ein Durante la configuracin, cuando se pida la CONTRASEA DEL DISPOSITIVO, hay que introducir 888888 48 Device name Device code 888888

(Default) We recommend to change the device password once installed for maximum Security Per una massima sicurezza si consiglia di cambiare la password del dispositivo Pour plus de scurit, il est conseill de choisir un autre mot de passe aprs avoir install le dispositif. Om de veiligheid te verhogen, raden wij u aan het wachtwoord van het apparaat na de installatie Wir empfehlen aus Sicherheitsgrnden das Passwort des Gerts nach Installation zu ndern Para mayor seguridad, se aconseja cambiar la contrasea del dispositivo 1. 2. Device name 3. 49 If you are using the door strike feature, we recommend that you set a unlock password (default 888888). Otherwise you can activate the One-Key Unlock feature. Se si vuole utilizzare il comando APRIPORTA da smartphone, per maggiore sicurezza raccomandiamo di inserire ogni volta la password (default 888888). possibile altrimenti attivare la funzione di memorizzazione password premendo Sblocco One-Key. Pour utiliser la commande OUVRE-PORTE en toute scurit sur un smartphone, il est prfrable de saisir chaque fois le mot de passe (par dfaut 888888). Il est galement possible de valider la fonction de mmorisation du mot de passe en appuyant sur Dverrouillage One-Key. Als u de opdracht DEURSLOTBEDIENING vanaf uw smartphone wilt gebruiken, is het voor een hogere veiligheid raadzaam om telkens het wachtwoord (standaard 888888) in te voeren. Anders is het mogelijk de functieWachtwoord onthouden te activeren met een druk op ONE-KEY ONTGRENDELEN. Wenn Sie den TRFFNER ber Smartphone verwenden mchten, sollten Sie zur Sicherheit das Passwort jedes Mal eingeben (Werkseitig 888888). Sie knnen andernfalls die Funktion Passwort speichern durch Klicken auf OneKey Entsperrung aktivierern. Si se desea usar el mando ABREPUERTAS desde un telfono inteligente, para mayor seguridad se aconseja introducir cada vez la contrasea (por defecto, 888888). En cualquier caso, es posible activar la funcin de memorizacin de la contrasea pulsando Desbloqueo de una clave. 1. 2. 3. 50 1. The Master user can invite an unlimited number of Slave users using the My Share button in the settings menu. Lutente Master pu invitare un numero illimitato di utenti Slave utilizzando il pulsante La mia condivisione nel menu impostazioni. Lusager Master peut inviter un nombre illimit dusagers Slave en utilisant le bouton My Share dans le menu des rglages. De hoofdgebruiker kan een onbeperkt aantal andere gebruikers uitnodigen met behulp van de Mijn delen-knop in het menu instellingen. Der Master-Benutzer kann eine unbegrenzte Anzahl von Slave-Benutzern einladen, indem er im Einstellungsmen die Schaltflche My Share verwendet. El usuario registrado como Master (maestro) puede invitar a un nmero ilimitado de usuarios Esclavos utilizando el botn Mi elemento compartido en el men de configuracin. 2. 51 ATTENTION! Visto2 needs to be upadted to the latest firmware version. In the Visto Comelit app, a red dot on the symbol, at the top right, indicates the availability of updates and useful information for the proper functioning of the device. Once your device is connected to the network, it is highly recommended to update it. firmware. ATTENZIONE! necessario che Visto2 disponga dellultima versione Nella app Comelit Visto un punto rosso sul simbolo in alto a destra indica che sono disponibili aggiornamenti e informazioni utili per il buon funzionamento del dispositivo. Una volta che il dispositivo connesso alla rete, si consiglia di procedere con laggiornamento. ATTENTION! Il est ncessaire que Visto2 dispose de la dernire version du firmware. Dans l'application Comelit Visto un point rouge sur le symbole en haut droite indique que des mises jour et des informations sont disponibles pour aider l'appareil fonctionner correctement. Lorsque le dispositif est connect au rseau, procder la mise jour. ATTENTIE! Update Visto2 naar de laatste firmware versie. In de Comelit Visto app geeft een rode stip op het symbool rechtsboven aan of er updates beschikbaar zijn. Tevens is hier nuttige informatie over de juiste werking van het apparaat te vinden. Zodra het apparaat op het netwerk is aangesloten, is het raadzaam om te controleren of de nieuwste firmwareversie wordt gebruikt. ACHTUNG! Visto2 muss auf die neueste Firmware-Version aktualisiert werden. In der Visto Comelit App zeigt ein roter Punkt auf dem Symbol oben rechts die Verfgbarkeit von Updates und ntzliche Informationen fr die ordnungsgeme Funktion des Gerts an. Nachdem das Gert mit dem Netz verbunden ist, berprfen Sie bitte, ob es die neueste Firmwareversion benutzt. 52 ADVERTENCIA! Es necesario que Visto2 tenga la ltima versin de firmware. En la aplicacin Comelit Un punto rojo en el smbolo en la parte superior derecha indica que las actualizaciones y la informacin estn disponibles para ayudar al dispositivo a funcionar correctamente. Una vez que el dispositivo est conectado a la red, recomendamos proceder con la actualizacin. 1. 2. 3. 4. 53 COMPLETE MANUAL WIRING DIAGRAMS www.vistodoorbell.com

DATE : 2019-06-21 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 On our behaif, | appoint Jason Wu of Global United Technology Services Co., Ltd.and No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China to act as our agent in the preparation of this application for equipment certification. | certify that submitted documents properly describe the device or system for which equipment certification is sought. | also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commissions regulations have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, | acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with Comelit Group Spa and via Don Arrigoni 5 san Lorenzo di Rovetta Bergamo ltaly Signature: [x Laer Name: Cong Chen Title: Project Manager Company: Comelit Group Spa

Comelit Group Spa DATE : 2019-06-21 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2ANSR-CM96201FR Product Name: Smart Video Doorbell Request for Confidentialit Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential:

(List here the documents for which you are seeking confidentiality for example ...) e Schematics e Block diagram e Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Signature: U4 chin Name: Cong Chen Title: Project Manager Company: Comelit Group Spa

Cover Page Global United Technology Services Co., Ltd. Report No.: GTS201905000212F01 TEST REPORT Applicant:

Comelit Group Spa Address of Applicant:

via Don Arrigoni 5 san Lorenzo di Rovetta Bergamo Italy Manufacturer:

Zhong Shan Jesmay Electronics Co., Ltd Address of Manufacturer:

First Industry District, Tan Zhou, Zhong Shan, Canton, China Equipment Under Test (EUT) Product Name:

Smart Video Doorbell Model No.:

CM96201FR-CMS FCC ID:

2ANSR-CM96201FR Applicable standards:

FCC CFR Title 47 Part 15 Subpart C Section 15.231 Date of sample receipt: May 27, 2019 Date of Test:

May 28, 2019-June 20, 2019 Date of report issued:

June 21, 2019 Test Result :

PASS *

*

In the configuration tested, the EUT complied with the standards specified above. Authorized Signature:

Robinson Lo Laboratory Manager This results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver. Page 1 of 21 2 Version Report No.: GTS201905000212F01 Version No. Date 01 June 21, 2019 Description Original Prepared By:

Date:

June 21, 2019 Check By:

Project Engineer Date:

June 21, 2019 Reviewer Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 2 of 21 3 Contents Report No.: GTS201905000212F01 Page 1 2 3 4 COVER PAGE .......................................................................................................................................... 1 VERSION .................................................................................................................................................. 2 CONTENTS .............................................................................................................................................. 3 TEST SUMMARY ..................................................................................................................................... 4 4.1 MEASUREMENT UNCERTAINTY ............................................................................................................ 4 5 GENERAL INFORMATION ...................................................................................................................... 5 5.1 5.2 5.3 5.4 5.5 5.6 GENERAL DESCRIPTION OF EUT ......................................................................................................... 5 TEST MODE ........................................................................................................................................ 6 DESCRIPTION OF SUPPORT UNITS ....................................................................................................... 6 TEST FACILITY .................................................................................................................................... 6 TEST LOCATION ................................................................................................................................. 6 OTHER INFORMATION REQUESTED BY THE CUSTOMER ......................................................................... 6 TEST INSTRUMENTS LIST ..................................................................................................................... 7 TEST RESULTS AND MEASUREMENT DATA ...................................................................................... 9 7.1 7.2 7.3 7.4 7.5 ANTENNA REQUIREMENT .................................................................................................................... 9 CONDUCTED EMISSIONS ................................................................................................................... 10 RADIATED EMISSION METHOD ........................................................................................................... 13 7.3.1 Field Strength of The Fundamental Signal ................................................................................ 14 7.3.2 Spurious Emissions ................................................................................................................... 15 20DB OCCUPY BANDWIDTH .............................................................................................................. 19 DWELL TIME ..................................................................................................................................... 20 TEST SETUP PHOTO ............................................................................................................................ 21 EUT CONSTRUCTIONAL DETAILS ..................................................................................................... 21 6 7 8 9 Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 3 of 21 Report No.: GTS201905000212F01 4 Test Summary Test Item Section in CFR 47 Result Antenna Requirement Conduction Emission 15.203 15.207 Field strength of the Fundamental Signal 15.231 (b) Spurious Emissions 15.231 (b)/15.209 20dB Bandwidth Dwell Time 15.231 (c) 15.231 (a)(1) Pass: The EUT complies with the essential requirements in the standard. N/A: Not applicable. Pass Pass Pass Pass Pass Pass 4.1 Measurement Uncertainty Test Item Frequency Range Measurement Uncertainty Notes Radiated Emission 9kHz ~ 30MHz Radiated Emission 30MHz ~ 1000MHz Radiated Emission 1GHz ~ 26.5GHz AC Power Line Conducted Emission 0.15MHz ~ 30MHz 4.64dB 4.64dB 3.68dB 3.44dB

(1)

(1)

(1)

(1) Note (1): The measurement uncertainty is for coverage factor of k=2 and a level of confidence of 95%. Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 4 of 21 Report No.: GTS201905000212F01 5 General Information 5.1 General Description of EUT Product Name:

Smart Video Doorbell Model No.:

Serial No.:

CM96201FR-CMS as0745qwcd Hardware Version:

ALM-VA-MB-222D20181031 Software Version:

V1.0.0 Test sample(s) ID:

GTS201905000212-1 Sample(s) Status:

Engineer sample Operation Frequency:

433.92MHz Modulation technology:

ASK Antenna Type:

Antenna gain:

Power supply:

Integral Antenna 2.0dBi(declare by applicant) DC 12V Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 5 of 21 5.2 Test mode Report No.: GTS201905000212F01 Transmitting mode Keep the EUT in transmitting mode. Per-test mode. We have verified the construction and function in typical operation, The EUT was placed on three different polar directions; i.e. X axis, Y axis, Z axis. which only the worst case was shown in this test report and defined as follows:

Axis 433.92MHz Field Strength(dBuV/m) 5.3 Description of Support Units X 71.26 Y 72.55 Z 70.34 Manufacturer Description Model Serial Number Zhong Shan Jesmay Electronics 5.4 Test Facility Smart Video Doorbell CM93602W NA The test facility is recognized, certified, or accredited by the following organizations:

FCC Registration No.: 381383 Global United Technology Services Co., Ltd., Shenzhen EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in files. Registration 381383. Industry Canada (IC) Registration No.: 9079A-2 The 3m Semi-anechoic chamber of Global United Technology Services Co., Ltd. has been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 9079A-2. NVLAP (LAB CODE:600179-0) Global United Technology Services Co., Ltd., is accredited by the National Voluntary Laboratory Accreditation Program (NVLAP). LAB CODE:600179-0 5.5 Test Location All tests were performed at:

Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China Tel: 0755-27798480 Fax: 0755-27798960 5.6 Other Information Requested by the Customer None. Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 6 of 21 6 Test Instruments list Radiated Emission:

Report No.: GTS201905000212F01 Item Test Equipment Manufacturer Model No. Inventory Cal.Date No.

(mm-dd-yy) Cal.Due date

(mm-dd-yy) 1 2 3 4 5 3m Semi- Anechoic Chamber Control Room EMI Test Receiver BiConiLog Antenna Double -ridged waveguide horn Horn Antenna EMI Test Software 6 7 8 9 10 11 12 Amplifier(100kHz-3GHz) 13 Amplifier(2GHz-20GHz) Coaxial Cable Coaxial Cable Coaxial cable Coaxial Cable ZhongYu Electron 9.2(L)*6.2(W)* 6.4(H) GTS250 July. 03 2015 July. 02 2020 ZhongYu Electron Rohde & Schwarz SCHWARZBECK MESS-ELEKTRONIK SCHWARZBECK MESS-ELEKTRONIK 6.2(L)*2.5(W)* 2.4(H) GTS251 GTS203 ESU26 N/A N/A June. 27 2018 June. 26 2019 VULB9163 GTS214 June. 27 2018 June. 26 2019 BBHA 9120 D GTS208 June. 27 2018 June. 26 2019 ETS-LINDGREN 3160 GTS217 June. 27 2018 June. 26 2019 AUDIX GTS GTS GTS GTS HP HP E3 N/A N/A N/A N/A 8347A 84722A AFS33-18002 650-30-8P-44 N/A GTS213 GTS211 GTS210 GTS212 GTS204 GTS206 N/A N/A June. 27 2018 June. 26 2019 June. 27 2018 June. 26 2019 June. 27 2018 June. 26 2019 June. 27 2018 June. 26 2019 June. 27 2018 June. 26 2019 June. 27 2018 June. 26 2019 GTS218 June. 27 2018 June. 26 2019 14 Amplifier (18-26GHz) Rohde & Schwarz Band filter Amindeon 82346 GTS219 June. 27 2018 June. 26 2019 Power Meter Power Sensor Wideband Radio Communication Tester Splitter Loop Antenna Breitband hornantenne Amplifier Amplifier PSA Series Spectrum Analyzer Anritsu Anritsu ML2495A MA2411B GTS540 GTS541 June. 27 2018 June. 26 2019 June. 27 2018 June. 26 2019 Rohde & Schwarz CMW500 GTS575 June. 27 2018 June. 26 2019 Agilent ZHINAN 11636B ZN30900A GTS237 GTS534 June. 27 2018 June. 26 2019 June. 27 2018 June. 26 2019 SCHWARZBECK BBHA 9170 GTS579 Oct. 20 2018 Oct. 19 2019 TDK TDK PA-02-02 PA-02-03 GTS574 GTS576 Oct. 20 2018 Oct. 19 2019 Oct. 20 2018 Oct. 19 2019 Rohde & Schwarz FSP GTS578 June. 27 2018 June. 26 2019 15 16 17 18 19 20 21 22 23 24 Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 7 of 21 Conducted Emission Item Test Equipment Manufacturer Model No. Shielding Room ZhongYu Electron 7.3(L)x3.1(W)x2.9(H) ESCI 7 MP59B 1 2 3 4 5 6 7 8 EMI Test Receiver R&S Coaxial Switch Artificial Mains Network Coaxial Cable EMI Test Software Thermo meter Absorbing clamp ANRITSU CORP SCHWARZBECK MESS GTS AUDIX KTJ Elektronik-

Feinmechanik Report No.: GTS201905000212F01 Inventory Cal.Date Cal.Due date No. GTS252 GTS552 GTS225

(mm-dd-yy)

(mm-dd-yy) May.15 2019 May.14 2022 June. 27 2018 June. 26 2019 June. 27 2018 June. 26 2019 NSLK8127 GTS226 June. 27 2018 June. 26 2019 N/A E3 TA328 GTS227 N/A June. 27 2018 June. 26 2019 N/A N/A GTS233 June. 27 2018 June. 26 2019 MDS21 GTS229 June. 27 2018 June. 26 2019 General used equipment:

Item Test Equipment Manufacturer Model No. Inventory No. Cal.Date Cal.Due date

(mm-dd-yy)

(mm-dd-yy) 1 Barometer ChangChun DYM3 GTS257 June 27 2018 June 26 2019 Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 8 of 21 7 7.1 Antenna Requirement Test results and Measurement Data Standard requirement:

FCC Part15 C Section 15.203 15.203 requirement:

Report No.: GTS201905000212F01 An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator, the manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. EUT Antenna:

The antenna is integral antenna, the best case gain of the antenna is 2.0dBi, reference to the appendix II for details Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 9 of 21 7.2 Conducted Emissions Report No.: GTS201905000212F01 Test Requirement:

FCC Part15 C Section 15.207 Test Method:

ANSI C63.10:2013 Test Frequency Range:

150KHz to 30MHz Receiver setup:

Limit:

Test setup:

RBW=9KHz, VBW=30KHz, Sweep time=auto Frequency range (MHz) 0.15-0.5 0.5-5 5-30 Limit (dBuV) Quasi-peak 66 to 56*

56 60 Average 56 to 46*

46 50

* Decreases with the logarithm of the frequency. Test Instruments:

Refer to section 6.0 for details Test mode:

Test environment:

Refer to section 5.2 for details Temp.:

25 C Humid.:

50%

Press.: 1 010mbar Test voltage:

Test results:

DC12V Pass Remark: Both high and low voltages have been tested to show only the worst low voltage test data. Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 10 of 21 Measurement data Report No.: GTS201905000212F01 Mode:

Transmitting mode Polarization:

Line Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 11 of 21 Mode:

Transmitting mode Polarization:

Neutral Report No.: GTS201905000212F01 Notes:

1. An initial pre-scan was performed on the line and neutral lines with peak detector. 2. Quasi-Peak and Average measurement were performed at the frequencies with maximized peak emission. 3. Final Level =Receiver Read level + LISN Factor + Cable Loss 4. If the average limit is met when using a quasi-peak detector receiver, the EUT shall be deemed to meet both limits and measurement with the average detector receiver is unnecessary. Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 12 of 21 7.3 Radiated Emission Method Report No.: GTS201905000212F01 Test Requirement:

FCC Part15 C Section 15.231 (b)& Section 15.209 Test Method:

ANSI C63.10:2013 Test Frequency Range:

9kHz to 5000MHz Test site:

Receiver setup:

Limit:

(Field strength of the fundamental signal) Limit:

(Spurious Emissions) Measurement Distance: 3m Frequency Detector RBW VBW Value 9KHz-150KHz Quasi-peak 200Hz 600Hz Quasi-peak 150KHz-30MHz Quasi-peak 9KHz 30KHz Quasi-peak 30MHz-1GHz Quasi-peak 120KHz 300KHz Quasi-peak Above 1GHz Peak Peak 1MHz 1MHz 3MHz 10Hz Peak Average Frequency Limit (dBuV/m @3m) Remark 433.92MHz 100.83 80.83 Fundamental Frequency

(MHz) 40.66-40.70 70-130 130-174 174-260 260-470 Above 470 Frequency

(MHz) Above 1000 Peak Value Average Value Field Strength of Unwanted Emissions

(microvolts/meter) 225 125 Field Strength of fundamental

(microvolts/meter) 2250 1250 1250 to 3750**

125 to 735 3750 375 3750 to12500 375 to 1250 12500 1250 Class B(dBuV/m @3m) Peak 74 Average 54 Or The maximum permitted unwanted emission level is 20 dB below the maximum permitted fundamental level whichever limit permits higher field strength. Test setup:

Below 30MHz Below 1GHz Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 13 of 21 Above 1GHz Report No.: GTS201905000212F01 Test Instruments:

Refer to section 6.0 for details Test mode:

Refer to section 5.2 for details Test environment:

Temp.:

25 C Humid.:

50%

Press.:

1 010mbar Test results:

Pass Measurement data:

7.3.1 Field Strength of The Fundamental Signal Peak value:

Frequency

(MHz) Read Level

(dBuV) Antenna Factor

(dB/m) Cable Loss

(dB) Preamp Factor

(dB) Level

(dBuV/m) Limit Line

(dBuV/m) Over Limit

(dB) polarization 433.92 89.94 16.03 3.02 37.52 71.47 80.82

-9.35 Horizontal 433.92 91.02 16.03 3.02 37.52 72.55 80.82

-8.27 Vertical Remarks:

1. Final Level =Receiver Read level + Antenna Factor + Cable Loss Preamplifier Factor 2. Average limit shall apply to PK value Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 14 of 21 7.3.2 Spurious Emissions Measurement data:

9 kHz ~ 30 MHz Report No.: GTS201905000212F01 The low frequency, which started from 9 kHz to 30 MHz, was pre-scanned and the result which was 20 dB lower than the limit line per 15.31(o) was not reported. Below 1GHz:

Mode:

Transmitting mode Polarization:

Horizontal Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 15 of 21 Report No.: GTS201905000212F01 Mode:

Transmitting mode Polarization:

Vertical Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 16 of 21 Above 1G:

Report No.: GTS201905000212F01 Mode:

Transmitting mode Polarization:

Horizontal Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 17 of 21 Mode:

Transmitting mode Polarization:

Vertical Report No.: GTS201905000212F01 Remarks:

Final Level =Receiver Read level + Antenna Factor + Cable Loss Preamplifier Factor Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 18 of 21 7.4 20dB Occupy Bandwidth Report No.: GTS201905000212F01 Test Requirement:

FCC Part15 C Section 15.231 (c) Test Method:

ANSI C63.10:2013 Limit:

Test setup:

The bandwidth of the emission shall be no wider than 0.25% of the center frequency for devices operating above 70 MHz and below 900MHz. For devices operating above 900 MHz, the emission shall be no wider than 0.5% of the center frequency. Bandwidth is determined at the points 20 dB down from the modulated carrier. Test Instruments:

Refer to section 6.0 for details Test mode:

Test results:

Measurement Data Refer to section 5.2 for details Pass Test Frequency (MHz) 20dB bandwidth (kHz) Limit (MHz) 433.92 17.417 1.085 Result Pass Note: Limit= Fundamental frequency0.25%

433.920.25%=1.085MHz Test plot as follows:

Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 19 of 21 7.5 Dwell Time Report No.: GTS201905000212F01 Test Requirement:

FCC Part15 C Section 15.231 (a)(1) Test Method:

ANSI C63.10:2013 Receiver setup:

RBW=100KHz, VBW=100KHz, span=0Hz, detector: Peak Limit:

Test setup:

Not more than 5 seconds Test Instruments:

Refer to section 6.0 for details Test mode:

Test results:

Refer to section 5.2 for details Pass Measurement data:

Frequency

(MHz) 433.92 Duration of each TX

(second) 0.044 Limit

(second)

<5.0 Result Pass Test plot as follows:

Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 20 of 21 Report No.: GTS201905000212F01 8 Test Setup Photo Reference to the appendix I for details. 9 EUT Constructional Details Reference to the appendix II for details.

------ End ------

Global United Technology Services Co., Ltd. No. 301-309, 3/F., Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 21 of 21

Radiated Emission Conducted Emission

Label: White coated paper Size: 18mm*30mm Product Name: Smart Video Doorbell Model No.: CM96201FR-CMS FCC ID: 2ANSR-CM96201FR IC: 25051-CM96201FR This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. label location