MevelMateRRO es |
Using LevelMatePRO
@ Position your vehicle Move your vehicle tothe position where you would lke to begin leveling and setup. connect to LeveiMatePRO Aer you have completed he instalation and configuration of your LevelMatePRO unit and app (onthe reverse side of tis page), you re ready o begin using the product to level your vehicle. To connect o your LeveMatePRO simply start the app within range of your LevellfatePRO unt (approximately 50), This can be done trom inside your vehicle and the Bletoth connection should interfere wih any oer Bluetooth connections you may have active, including hands-free Bluetooth phone systems, you do have ofter Bluetooth connections that interfere with the connection te your LevlMatePRO, cont he ser manuals of your phone andor those devices to see if here are device connection restrictions hat are causing he connection issue The Leveting screen ak ene pel al eve etic cecal not Severe tun ae oase, tocomss secon Siroslad tea ekg redonariaes nee dnioce 2 yew aru (eho el inal poten} nda evel mtr sled oto Q Level your vehicle from side-to-side As noted above, when leveling your vehicle from side-side you wil be Using the top section ofthe Leveling screen. When the vehicle is notin @
level position, there wil bea yellow arow poiting upward on one side of the valer graphic font view. This indicates which side ofthe vehicle needs tobe raised to achieve a level postion trom side-to-side. The displayed measurement indicates how much height willbe required on the side where the arrow is dsplayed. Stack your leveling blocks to the height indicate by the displayed measurement and place the blocks in the front o rear of the ties) on the side indicated by the arrow. Then move your vehicle so thal the tes are on top blocks and check he level indicator displayed under the measurement distance. Ifyou have achieved a level positon, the ive indicator wil be green and the displayed measurement cstance wl be 0.00 as in figure 2. Ifthe level ingeatoris red and the daplayed measurement distance snot 000, then not the measurement disance and move the vehicle te() ofthe biocks and add or remove blocks equaling the measurement distance that was displayed when the tre(s) were onthe blocks. Once again, move the vehicle irs) onto the blocks and check the level incicator and measurement distance to insure that the vehicle is now level from side-to-side. seve your hiten position oar ace sary oecves ovac aoc oes temo Lever your venict rom frontto-back ee Ce stm uae es Cautious Se eee eaten the Has eri abet a epee
@ Recait your hitch position ifthe vehicle you are leveling is a tral, you can recall the hitch postion you saved instep 5 to id in returning your tongue tothe poston it was in wen you removed it from the tow vehicle hitch. Tapon the Recall itch position button a the lower right ofthe Leveling seen, The Recall Hitch Position screen wil be displayed (gure 3), The Recall Hitch Postion screen shows a side View of the trailer, a yellow arow pointing up or down, and position indicator simiar tothe level indicators on the Leveling screen Ameasurement distance is also displayed which represents the amount of distance the tongue needs to be moved up or down (as indicated by the yellow arrow) to return to the previously saved hitch postion, Moving the tral tongue in he direction indicated by the yellow arow wil cause the displayed measurement cistance fo be reduced. The tongue wil be at the saved hitch position when the displayed distance measurement is 0.00 and the poston indcatoris green as shown in fgure 4 Abltch Position Save Date is also displayed atthe bottom ofthe Recall Hitch Position screen. This indicates when the currently save hitch position was saved. SPM Paes aas) oa LevelMatePRO eee loner!
ite MslteaaMie Seta Level Indicators t
) eT eu ee Ear Hitch Position Save Date figure 3 figure 4 2 ro LevelMatePRO Distance Measurement Directional Arrow Pere UE eee