Caution Changes or modifications not expressly approved by the party responsible for the compliance could void the users authority to operate the equipment. FCC Statements This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference received, including interference that may cause undesired operation. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference that may cause undesired operation. This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20cm is maintained between the antenna and users. For laptop installations, the antenna must be installed to ensure that the proper spacing is maintained in the event the users places the upper portion of the LCD panel only to ensure 20cm will be maintained if the user places the device in their lap for use), and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as the 2 condition above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product . In these circumstances, the OEM integrator will be responsible for re-evaluating the end product ( including the transmitter) and obtaining a separate FCC authorization. End Product Labeling:
This transmitter module is authorized only for use in device where the antenna may be installed such that 20cm may be maintained between the antenna and users(for example access points, routers, wireless ADSL modems, certain laptop configurations, and similar equipment). The final end product must be labeled in a visible area with the following:
Contains FCC ID:TK4-06-WLM54GP26 Manual information for End users The end user must not have manual instructions to remove or install the device. The user manual for end user must include the following information in a prominent location. IMPORTANT NOTE:
To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter product datasheet
High Output Power of up to 26dBm on both B and G band
Available in G and Super-G modes
Affordable and ideal for a variety of applications WLM MINIPCI SERIES WLM54G (G) 26dBm (400mW) WLM54G (SUPER-G) 26dBm (400mW) Compex WLM54G-26dBm miniPCI network adapter offers high output power of 400mW, extending the range of embedded devices much further. Combined with excellent receiver sensitivity, Compex WLM54G-26dBm is the miniPCI of choice for long distance links, or those where signal levels are reduced due to minor obstructions such as trees or buildings. Built on Atheros chipset, Compex WLM54G-26dBm miniPCI network adapter can be used for all IEEE802.11b/g compatible WLAN. It is ideal for integration in a wide range of OEM devices. Compex WLM54G-26dBm is also available in Super-G mode, which delivers better performance at higher throughput for your network connectivity. Features
2.4GHz IEEE 802.11 b/g standard
Up to 108Mbps high-speed data rate (Super-G model)
High Output Power of up to 26dBm at b/g Band
Dynamic Frequency Selection (DFS)
Wi-Fi Protected Access Client Support (WPA)
Transmission Power Control (TPC)
Multi-country Roaming Support (IEEE802.11d)
Suitable for Embedded System or OEM project
Available in Wireless-G, Super-G modes Applications Embedded system or OEM device Infrastructure Networking Copyright 2006 Compex Systems. All rights reserved. COMPEX and the COMPEX logo, are registered trademarks of COMPEX Inc. While every effort is made to ensure the information is accurate, Compex does not accept liability for any errors or mistakes that may arise. All specification is subject to change without notice. Datasheet version: V1.1 WLM MINI PCI TECHNICAL SPECIFICATIONS MODEL CHIPSET SPEED (max) OUTPUT POWER 802.11b 1-11Mbps 802.11g 6-24Mbps 36Mbps 48Mbps 54Mbps POWER CONSUMPTION STANDARDS WLM54G-26dBm (G) WLM54G-26dBm (Super-G)
(High Power) Atheros AR2413 54Mbps
(High Power) Atheros AR2414 108Mbps 26dBm 26dBm 25dBm 24dBm 22dBm 5W 26dBm 26dBm 25dBm 24dBm 22dBm 5W IEEE 802.11b:
11Mbps, 5.5Mbps, 2Mbps, 1Mbps IEEE 802.11g:
54Mbps, 48Mbps, 36Mbps, 24Mbps, 18Mbps, 12Mbps, 9Mbps, 6Mbps, automatically fallback to 5.5Mbps, 2Mbps, 1Mbps Super-G:
108Mbps, 96Mbps, 72Mbps, 54Mbps, 48Mbps, 36Mbps, 24Mbps, 18Mbps, 12Mbps, 6Mbps FREQUENCY RANGE IEEE 802.11b/g 2.412GHz ~ 2.462GHz (US & Canada) 2.412GHz ~ 2.472GHz (Europe) 2.412GHz ~ 2.484GHz (Japan) NETWORK INTERFACE PCI interface v2.3 (Type III-B Mini PCI form factor) MODULATION TECHNIQUES OFDM and DSSS OFDM: BPSK, QPSK, 16 QAM, 64QAM DSSS: DBPSK, DQPSK, CCK RECEIVER SENSITIVITY 802.11b -92 dBm @ 1Mbps, -87 dBm @ 11Mbps 802.11g -90 dBm @ 6Mbps, -70 dBm @ 54Mbps OPERATING CHANNELS US and Canada Europe Japan 11 Channels 13 Channels 14 Channels SECURITY 64/128 Bit WEP, WPA/WPA2 , IEE802.1X Authentication ENVIRONMENTAL SPECIFICATIONS Temperature Operating -20C to 70C Storage -65C to 100C Humidity Operating 5% to 95% (non-condensing) DIMENSIONS & WEIGHT Dimensions 59.75mm*44.60mm (L x B) Weight 55 grams Compex Systems Pte Ltd 135 Joo Seng Road,
#08-01 PM Industrial Building Singapore 368363 tel: (65) 6288 8220 fax: (65) 6280-9947 www.compex.com.sg Compex Inc, USA. 840 Columbia Street, Suite B Brea. CA 92821 tel: (714) 482 0333 fax: (714) 482-0332 www.cpx.com Copyright 2006 Compex Systems. All rights reserved. COMPEX and the COMPEX logo, are registered trademarks of COMPEX Inc. While every effort is made to ensure the information is accurate, Compex does not accept liability for any errors or mistakes that may arise. All specification is subject to change without notice. Datasheet Version: V1.2