WAN LAN Power LAN port connect with a PC or a router Power POE port connect device LAN port (supply power to the device) NOTEUse LAN ports of the device to log in software Set your IP to "Use the following IP address"
192.168.110.3 255.255.255.0 AP Mode (sending)+WDS Current IP Current Lease Expires Renew Lease Now Wan Ethernet Port Normal Use ADSL AP+WDS Connection Basic Authentication DHCP Dynamic DNS Routing Wake on LAN DHCP LAN DHCP Server Enabled DHCP range Start End Lease Time Static IPs 192.168.110. 192.168.110. 12 hours 10 250 Block MAC addresses assigned a static IP that connect from a different IP Add Static IP Addresses Hostname optional MAC IP Add Select Hostname/MAC From Currently Connected Hosts Assigned Static IP Addresses N+A Default bandwidth Access Point SSID:
WiFi 2452MHz[11]
None Clients Quantity:
1.Write down ADSL and password 2.Set up IP address of Router (for example192.168.110.1 3.Frequency setting Notein generalroutersmobile phonelaptop only could receive 2.4Ghz channel 1Firstlychoosewidth of broadband 2Secondly choose the channel which you need inwireless channel 4.Write down the name of SSIDlikewifido not support Chinese SSID 5.Choose encryptionlikechoose WPA PSKadd wifi paaaword 6.Save changesSelect Statusto cancelDHCP Serviespicture above 7.Save and finish setting. 1.Change WAN port into LAN port accodring to demand 2.Set up IP address of Router (for example:192.168.110.1) 3.Setting SSID, scan the avaliable wifi singal 6
+WDS ADSL AP+WDS Wireless Bridge/Repeater Bridge IP Subnet Mask AP/Gateway IP 192.168.110.2 255.255.255.0 192.168.110.1 Wan Ethernet Port Disable DNS Servers:
Use Gateway As DNS Server
(must be in AP subnet)
(same as AP mask) Connect Via WDS Operation Mode Channel Width Transmit Power SSID to Join MAC BindingBlank if not binding Wireless Channel Encryption N+A 40MHz (2nd chan. below Max WiFi 27
(0-27dbm) Scan 2452MHz[11]
None Current IP Current Lease Expires Renew Lease Now Wan Ethernet Port Disable ADSL AP+WDS Wireless SSID to Join:
MAC Binding(Blank if not binding):
Wireless Channel:
Encryption:
Access Point SSID:
Clients Quantity Disable 1111 scan 2462MHz[11]
None 2222 2452MHz[11]
None Default bandwidth I 7-10 Q8.Light of signal Red:PWR:power light showing the normal working status. Blue:WLAN:wifi singal light the strobe light show the normal working status. WAN,LAN:LAN light showing the normal working stats. Orange:1-4 Signal.Strengh Indicator Light 1,The signal is too weak. Light 1.2, The signal is weak. Light 1.2.3,The signal is general. Light 4,The signal is too strong. Light1.2.3.4,The best signal. FCC Warnning:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.