1783/2082 14:21 COMPUTIME LTD
. [wreRmaric:
Wireless Alarm with Motion Sensor
> +852 2785 5487 LOCATION OF CONTROLS 1. Motion Sensor 2. Alarm Speaker 3. Keypad 4. Status LED 5. Battery Compartment
&, RF Siren Speaker Unit programmable switch BATTERY INSTALLATION (SEE FIGURES BELOW) ;
Access the battery compartment on the rear of the unit by removing the back cover. Press on tha upper center part of the cover and slide it down, Insert four (4) AA batteries (not included) following the polar ly diagram. When the last battery is inserted, the Battery Low LEC will flash and the Siren will chirp to indicate the batteries are installed property. Replace the battery compartment cover. The Siren will chirp every 10-15 seconds when the batteries need replacing. Slide down fe expose battery en\
BATTERY PRECAUTIONS Follow these precautions when using batteries in this device:
1. Use cnly the size and type of batteries specified, 2. Be sure to follow the correct polarity when installing the batterlas as Indicated in the battery compartment. Reversed batterles may cause damage to the device. 3. Do not mix different type of batteries together (e.g. Alkaline and Carbon-zinc) or ofd batteries with fresh ones. 4. Ifthe device is not te be used for a jong period of time, remove the bateries to prevent damage or injury from possible battery ge. 5. Do not try to recharge batteries not intended to be recharged:
they can overheat and rupture. (Follaw battery manufacturer's directions.) NOTE: Not intended for use in exposed outdoor applications. Will not feerate property if used In below freezing temperatures (32F) or damp HN a 2088 14:32 INTERMATIC INCORPORATED SPRING GROVE, ILLINOIS 60081-5598
+852 2798 3996 PROGRAMMING THE ALARM Tha desired 4-digit code must be se after inserting the batteries, To sat th code, and simply prass the desired 4 To use the alarm in combination wi set programmable switch combination!
Remove battery compartment cover, Fi Locate the programmable switch a positions. Replace batteries and bate iment cover. Set switches of the pi Ir switch of the Siren Speaker Unit atl pasitions. INSTALLATION The unit is designed to be either frees wail mounted. For wall mounting pia the desired location, preferable next t back door. instalf the unit using the sug
(see figure at right). fe Using Remote AF Alarm To use the alarm unit in combinations Siren Speaker Unit, locate the RF Sp grammable switch and set the 3 switch the settings of the 3 dip switch sel SPS501B RF Siren Speaker. OPERATION Arminy Alarm When leaving the protected area, pres LED will flash and the Given will chi Thore will be a delay of 30 seconds tale F i is detected, the alarn ed area before the alarm sounds. Whe witt sound, WARNING: THE ALARM SIREN IS. Disarming Alam When returning to the protected a alarm code. This will disarm the unit Ou to ge to the alarm before it sount TE:
will flash and the Siren will chimp tq Care and Maintenance To clean the unit housing use a soft cld and wipe dry. Do not use chemical 4 discofor the unit. 37%
iii ediately (within 5 second irave batteries. PRY LOUD; PLEASE D0 NC ALLOW IT TO SOUND FOR LONG LEN hen the fourth digit of yourjReie is entered, the Status LE:
hiistightly dampened with wats i i 2, select four 4-digit access fs on tha keypad. bntrotied Siren Speaker Uned I:
im ker pro-
jo match eypad number 4, The State fo indicate the unit is armed lable you to leave the proteci S OF TIME. simply press your person, 2 10 seconds delay enable ents as this may damage an. ARTE 8683-2088 ive COMPLITIME LTE + 252 2745 S152 NO, B36 Dg2 WARNING '
Changes of modifications to this uni{ not expressly appoved by the party responsible or compliance could void the user's authority to operate the equipment, 4 in addition, for @ Class B digital device or peripheral of cordless phone. the user manual shai include the follaving or similar statement, placed in a prominent location in the text of the manual : |
NOTE '
This equipment has been tested and found to comaly with the mits fo a Ciass B cigite! device, pursuact to ode 15 of the FCC Rules. These limits are designed to provide reasonable protecton aganst harmful interference in a resident a! installation. This equipment generates, uses and can radiate rad o frequency enegy ard if not installed and used in accordance with the instructions, may cause harmful interference to radio Communications. i However, there is no guarantee that interference wil net occur na particu'ar instalation. If this equipment dogs cause harmful interference to radio oF television reception, which can be determined by turning the equipment off and or, the User is encouraged to try to corract the interference by one or mare of the following meas.res:
1, Reorient or relocate the receiving antenna. fi 2. Increase the separation between the equipment ard receiver. il 3, Connect the equigment into an outlet on 4 c.rcuit differert rom thal to which the receiver is needed 4. Consutt the dealer or an experienced radio/TV technician for help. f