all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 |
|
User Manual | Users Manual | 1.90 MiB | ||||
1 2 | Cover Letter(s) | |||||||
1 2 | External Photos | |||||||
1 2 | ID Label/Location Info | |||||||
1 2 | ID Label/Location Info | |||||||
1 2 | Internal Photos | |||||||
1 2 | RF Exposure Info | |||||||
1 2 | Test Report | |||||||
1 2 | Test Setup Photos |
1 2 | User Manual | Users Manual | 1.90 MiB |
WAP-5922 AC1200 WiFi Extender User Manual Version A2.0, September 14, 2018 Federal Communication Commission Interference Statement This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment. WiFi To prevent interference with cordless phones, ensure that gateway is at least 5 feet
( 1.5m )from the cordless phone base station. This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. EMC Warning This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Safety 1. This product is designed for indoor use only; DO NOT install the adapter outdoors. 2. Do NOT use near water. 3. DO NOT put this product at or near hot or humid places, e.g. kitchen or bathroom. DO NOT use any spray or liquids on it. 4. DO NOT touch the product with wet hands and DO NOT clean the product with a wet cloth. Use a soft, dry cloth to clean the device. 5. DO NOT expose the product to lit candles, cigarettes, open flames, high or low temperatures, etc. 6. DO NOT pull any connected cable with force; disconnect it from the power first. 7. Ensure proper ventilation, so that air flows freely around the product. 8. If you find that the product is not working properly, please contact your dealer of purchase and ask for help. Do NOT open the casing 9. DO NOT disassemble the product, warranty will be void. Power Specifications I/P 100-240Vac, 50/60Hz, 0.16A 1 Federal Communications Commission (FCC) Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the users authority to operate the equipment. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device. FCC RF Radiation Exposure Statement:
1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. 2 ISED Canadian Notice This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. Avis Canadien Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1. Lappareil ne doit pas produire de brouillage;
2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Caution: Exposure to Radio Frequency Radiation. 1. To comply with the Canadian RF exposure compliance requirements, this device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. 2. To comply with RSS 102 RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. Attention: exposition au rayonnement radiofrquence. 1. Pour se conformer aux exigences de conformit RF canadienne l'exposition, cet appareil et son antenne ne doivent pas tre co-localiss ou fonctionnant en conjonction avec une autre antenne ou transmetteur. 2. Pour se conformer aux exigences de conformit CNR 102 RF exposition, une distance de sparation d'au moins 20 cm doit tre maintenue entre l'antenne de cet appareil et toutes les personnes. Operationintheband51505250MHzisonlyforindoorusetoreducethepotential forharmfulinterferencetocochannelmobilesatellitesystems. Labande51505250MHzestrservsuniquementpouruneutilisation l'intrieurafinderduirelesrisquesdebrouillageprjudiciableauxsystmesde 3 satellitesmobilesutilisantlesmmescanaux. Forthefrequency56005650MHz,nooperationispermitted Pourlafrquence56005650MHz,aucuneoprationestautorise. 4 Preface This manual provides information related to the installation and operation of this Dual-Band Wireless Mesh Point. The individual reading this manual is presumed to have a basic understanding of home networking terminology and concepts. If you find the product to be inoperable or malfunctioning, please contact technical support for immediate service by email at homesupport@comtrend.com For product updates, new product release, manual revision, or software upgrades, please visit our website at http://www.comtrend.com Copyright Copyright 2018 Comtrend Corporation. All rights reserved. The information contained herein is proprietary to Comtrend Corporation. No part of this document may be translated, transcribed, reproduced, in any form, or by any means without the prior written consent of Comtrend Corporation. NOTE:
This document is subject to change without notice. Protect Our Environment This symbol indicates that when the equipment has reached the end of its useful life, it must be taken to a recycling center and processed separate from domestic waste. The cardboard box, the plastic in the packaging, and the parts that make up this device can be recycled in accordance with regionally established regulations. Never dispose of this electronic equipment along with your household waste. You may be subject to penalties or sanctions under the law. Instead, ask for disposal instructions from your municipal government. Please be responsible and protect our environment. Save Our Environment When this equipment has reached the end of its useful life, it must be taken to a recycling centre and processed separately from domestic waste. The cardboard box, the plastic in the packaging, and the parts that make up this device can be recycled in accordance with regionally established regulations. Never dispose of this electronic equipment along with your household waste. You may be subject to penalties or sanctions under the law. Instead, ask for disposal instructions from your municipal government. Please be responsible and protect our environment. 5 6 TableofContents Chapter 1 Product Information ..................................... 9 1.1 Introduction and Features ........................................ 9 1.2 System Requirements ............................................. 10 1.3 Package Contents ................................................... 11 1.4 Get familiar with your Wireless Mesh Point ............ 12 Chapter 2 Mesh WiFi-Supported Installation ............... 16 2.1 Device Setup ........................................................... 16 2.1.1 WiFi Network Setup ............................................................ 19 Chapter 3 Repeater Mode ............................................ 21 3.1 Repeater Mode Quick Installation Guide ................. 21 3.1.1 Hardware WPS button setup ......................................... 22 3.1.2 Web browser quick setup ................................................ 24 3.2 Repeater mode Advanced Settings .......................... 31 3.2.1 Connect to web configuration menu ........................ 31 3.2.2 Home ............................................................................................ 33 3.2.3 WPS Setting ............................................................................. 35 3.2.4 Advanced Settings ............................................................... 37 3.2.5 WLAN 2.4G settings ............................................................ 40 3.2.6 WLAN 5G settings ................................................................ 42 3.2.7 MAC Address Filtering ....................................................... 44 3.2.8 How to find the MAC address of your device ....... 46 3.2.9 System Utility ......................................................................... 50 3.2.10 Configuration ....................................................................... 52 Chapter 4 AP Mode ...................................................... 56 4.1 AP Mode Quick Installation Guide ........................... 56 4.1.2 Web browser quick setup ................................................ 57 4.2 AP Mode Advanced Settings .................................... 62 4.2.1 Connect to web configuration menu ........................ 62 4.2.2 Home ............................................................................................ 63 4.2.3 WPS Setting ............................................................................. 65 4.2.4 Advanced Settings ............................................................... 67 4.2.5 WLAN 2.4G settings ............................................................ 71 4.2.6 WLAN 5G settings ................................................................ 73 4.2.7 MAC Address Filtering ....................................................... 74 7 4.2.8 How to know the MAC address of your device ... 77 4.2.9 System Utility ......................................................................... 80 4.2.10 Configuration ....................................................................... 82 Chapter 5 Appendix..................................................... 85 5.1 Configuring TCP/IP on PC ....................................... 85 5.1.1 Windows XP IP address setup: .................................... 85 5.1.2 Windows Vista/Windows 7 IP address setup: ... 86 8 Chapter 1 Product Information 1.1 Introduction and Features The AC1200 Dual-Band Wireless Mesh Point has a compact design, and provides excellent network performance to extend your Wi-Fi signal and wireless coverage. Features of this Wireless Mesh Point include:
Easily extends the wireless signal inside your home or office. Compact design while maintaining excellent network performance. Supports 802.11a/b/g/n and 802.11ac standards, it can provide up to 300Mbps for 2.4Ghz on 11n mode and 866Mbps for 5Ghz on 11ac mode. LED signal indicators to easily realize the best location placement to extend the WiFi signal for best wireless performance. Supports Repeater mode and AP mode. WPS (Wi-Fi Protected Setup) hardware button for easy installation and wireless security. 9 1.2 System Requirements Wireless network card which is compatible with 802.11a/b/g/n and 802.11 ac wireless network standards. Windows XP, Windows 7, Windows 8, Windows 10 or MAC OS or Linux operating system. 10 1.3 Package Contents Before you start to use this Wireless Mesh Point, please check if theres anything missing in the package, and contact your place of purchase to claim for missing items:
Wireless Mesh Point (1 pcs) Quick Install Guide (1 pcs) 11 1.4 Get familiar with your Wireless Mesh Point Interface Descriptions B A C Item Name Description Item A LAN B Reset / WPS WiFi Output Power Switch C 10/100/1000M Ethernet LAN Port with Auto-MDI/MDI-X. Connect to a computer, switch or hub for local network sharing. Reset the Wireless Mesh Point to factory default settings (clear all settings) or start the WPS function. Press this button and hold for 10 seconds to restore all settings to factory defaults, or press this button for less than 5 seconds to start the WPS function. Switch the button to change. 12 LED Activity LEDs Behavior Description Note Signal Strength An optimal signal means the Wireless Mesh Point is placed with proper distance to help to extend the network. Good signal:
-45 to -60dBm Signal too strong:
> -45dBm LED1 on LED2 off LED3 off 1. The device is in repeater mode, when LED2 & 3 are off and LED1 is on. It means the device has optimal signal quality. 2. Device in AP mode, when LED1 is solid on, it represents the device is ready.
(Device ready means it obtained an IP from the uplink DHCP server.) 1. The device is in repeater mode, when LED1 & 3 are off and LED2 is on. It indicates the current placement is too close to the uplink router, which is not an effective placement of the wireless mesh point. LED1 off LED2 on LED3 off 13 LED1 off LED2 off LED3 on LED1 LED2 LED3 flashing 3. The device is in repeater mode, when LED1 & 2 are off and LED3 is on. It indicates the current placement is too far from the uplink router, which potentially makes the uplink connection weak and may result in slow speed or disconnection. 1. The device is not with a stable connection. It may be in the progress of pairing, grouping, and or synchronising. 2. The device will not be able to configure before these 3 LEDs stop flashing. LED 4 on The device is powered on. signal too weak:
< -60dBm The device in factory default and powered (with power LED on), in this state, it is not ready to make any configuration, and it needs to wait until LED1, 2 & 3 are flashing.
(If only the power LED on, the Wireless Mesh Point is still in booting process.) Power LED4 flashing LED4 off Firmware upgrading is taking place. Device is powered off or no power. 14 LED5 on 1. The device is successfully finished WPS handshaking. 2. The device is already paired or grouped with the current network. LED5 flashing The device is processing WPS PBC handshaking. There is a 120 second open window to process WPS PBC handshaking and after 120 seconds time out, the LED will turn Off. 1. The device is not performing WPS handshaking. 2. The device is not paired or grouped with any network. The device is connected to another device via Ethernet cable. The device is not connected to another device via Ethernet cable or no Ethernet cable is attached. There is Ethernet traffic. WPS &
Paring status Ethernet Off LED6 on Off Flashing 15 Chapter 2 Mesh WiFi-Supported Installation Scenario 1: Using a Comtrend Mesh WiFi-Supported Gateway Use anywhere from 1-10 Mesh Points on a single network. Scenario 2: Using a Non-Comtrend Mesh WiFi-Supported Gateway Use anywhere from 2-10 Mesh Points on a single network. Note: A minimum of 2 Mesh Points are required to create a connection for this scenario. 2.1 Device Setup The following steps show how to setup your Whole-Home WiFi Mesh System using Ethernet Pairing. For additional setup options (including WPS), please refer to the User Manual available online. NOTE: If you are using a Comtrend WiFi Mesh-Supported Gateway, then the Mesh Points will work in conjunction with your Gateways WiFi. If you are not using a Comtrend WiFi Mesh-Supported Gateway, then the WiFi Mesh Points will create a separate WiFi Mesh System (Note: This application will require at least two WiFi Mesh Devices to create a Mesh System). 1. Connect one end of an Ethernet Cable into each Mesh Point (WAP-5922) that you wish to have in your Whole-Home WiFi Mesh System. For this example, we will use two Mesh Points. 2. Plug the Mesh Points into an outlet near your Network Device (Router, Modem). Ethernet Cable Steps 1-2 16 3. Connect the other end of the Ethernet Cables into your Network Device. The pairing process will then automatically begin. 4. Wait until all WPS/Grouping LEDs light up solid (around 3 to 5 minutes). This means the two Mesh Points are now in the same WiFi Mesh System. If you are using a Comtrend WiFi Mesh-Supported Gateway, then the two Mesh Points are now in the same WiFi Mesh System as the Comtrend Gateway as well. 17 5. Disconnect the Ethernet Cables and unplug the Mesh Points. Then find a suitable location for each Mesh Point with an accessible power outlet. The Mesh Points should be placed in different directions between the Network Device and the areas farthest from the Network Device. NOTE: If you are not using a Comtrend WiFi Mesh-Supported Gateway, then you will need to leave one Mesh Point connected via Ethernet to the Network Device. The following LEDs will show you if you have the optimal placement. LED / Icon Status Indication Signal - Optimal First LED On Signal - Too Strong Second LED On Signal - Too Weak Third LED On The extender has an optimal signal connection with its uplink device. The distance in between is ideal. The extender has too strong a signal connection with its uplink device. The distance in between is too close. The extender has too weak a signal connection with its uplink device. The distance in between is too far. 6. Once the Mesh Points are plugged into their new locations, wait for the WPS/Grouping LEDs to light up solid. This means they are grouped again and the WiFi Mesh System is ready to use. 7. To add new Mesh Points to the Mesh System, simply plug the new device(s) into an outlet and press the WPS Button for 2-3 seconds. Within two minutes, press the WPS Button on a Mesh Point in the existing system. The WPS/Grouping LED will light up solid. 18 8. If you are using a Comtrend WiFi Mesh-Supported Gateway, then the WiFi Mesh System will automatically use the original WiFi settings on your Gateway. If you are using a Non-Comtrend WiFi-Supported Gateway, then please reference the back of the Mesh Point that is connected to the Gateway for the default SSID and Password WiFi settings. If you would like to change your networks SSID or Password please continue to section 2.1.1. 2.1.1 WiFi Network Setup 1. You can now use your computers Wireless configuration utility to search for a Wireless Network name such as: repeater0003.
(The default SSID of this Mesh point is repeater0003, and 0003 is for reference. It will be the last 4 digits of the devices MAC number.) 2. Open your Web browser, and input http://comtrend.setup in the address bar. 19 3. The system will prompt you to input the username and password. Default username is admin and password is 1234. Click the OK button to continue. 4. After you log into the Webpage, input your WiFi network name in the Device SSID field, and also the password in the KEY field for both the 2.4GHz and 5GHz WiFi networks. After the configuration, click the APPLY button to finish the setup. The devices will reboot, and when the WPS/Grouping LEDs on all of the Mesh Points light up solid, the Whole-Home WiFi Mesh System is ready. 20 Chapter 3 Repeater Mode This chapter will explain how to quickly install this device by using the quick setup method and explain each detailed setting on the web user interface while in repeater mode. 3.1 Repeater Mode Quick Installation Guide For first time setup and installation, move this Wireless Mesh Point close to the Wireless Broadband Router or Access point you wish to connect to. After installation is complete, move this Wireless Mesh Point to the place you wish to permanently wish to use it. Plug this Wireless Mesh Point into a power outlet on the wall, and you should see the Power LED light up in few seconds. If not, check if the power outlet youre using is working. You can setup the wireless connection via the Hardware WPS button or Software web browser. If your broadband router or access point also supports a WPS button, we recommend you to use the WPS button to establish connection. 21 Using WPS button Using Web browser 3.1.1 Hardware WPS button setup
- please go to section 3.1.1
- please go to section 3.1.2 1. Press and hold the WPS button on the Wireless Mesh Point for 2 seconds, the WPS LED will start flashing. WPS button WPS LED 2. Press the WPS button on the wireless broadband router or access point you wish to connect to within 2 minutes. 22 NOTE: the WPS button position on the access point above is for reference;
different devices may have different WPS button positions or locations. TIP: If the access point you wish to connect to does not have a hardware WPS button, you can also use its web configuration menus WPS function to establish connection. Or you can login to the WAP-5922s web user interface to perform quick setup (for detailed setup refer to 3.1.2 Web browser quick setup manual) 3. When WPS connection is successfully established, the Wireless Mesh Point will reboot immediately to make your settings take effect ; if the WPS LED flashes fast, a problem has occurred, please wait for 2 minutes until the WPS LED goes off, and start from step(1) again. When quick installation is successful, the Signal LED will turn on. Signal LED 4. Please plug this Wireless Mesh Point into a power outlet on the wall in the place you wish to use it (the ideal place will be the center of your house) and, the wireless connection will be established automatically as long as its within range of your wireless router or access point. 23 You can check the Signal LED status to understand signal reception level.
(Please see the table on page 14 for details.) If the Signal LED is off, it means the device is out of wireless range of your wireless broadband router or access point. Move the Mesh Point closer to the broadband router until the Wireless Mesh Point device can receive a signal from the broadband router and extend its signal. The quick installation setup is complete, you can refer to 3.2 Repeater mode Advanced Settings to login to the web user interface for other advanced settings. 3.1.2 Web browser quick setup Before you can connect to the Wireless Mesh Point and start the configuration procedures, your computer must be able to get an IP address automatically (use dynamic IP address). If its set to use a static IP address, or youre unsure, please refer to Chapter 6: 6.1 Configuring TCP/IP on PC to set your computer to use dynamic IP address. 1. Use an Ethernet cable to connect your computers Ethernet port and the wireless Mesh Points Ethernet port. Or use your computers wireless configuration utility to search for an access point named repeater0003 and get connected. (The default SSID of this Wireless Mesh Point device is repeater0003, 0003 is for reference, it is the last 4 digits of the devices MAC number. Each device has a different MAC number; please find it on your device label.) 24 NOTE: this default SSID repeater0003 is for reference, different devices may have different last 4 digits. If you are using a wireless connection in Windows Operating System and encountered the following screen, please click Connect the network without setting it up then you can successfully link to the Wireless Mesh Point. Do NOT click OK . In case you click OK, Windows Operating System will ask for the security key, please click Cancel to go back to this page. NOTE: this repeater0003 is for reference, 0003 are the last 4 digits of the devices MAC number. Each device has a different MAC number; please find it on your device label.) 2. Open your web browser, it will redirect to the web user interface setting page.
(or you can input the default IP address in the address bar) http://192.168.2.252 25 3. The Wireless Mesh Point will prompt you to input the username and password. Default username is admin and password is 1234. Click the OK button to continue. 4. All wireless access points nearby will be displayed on the list. Select one access point you want to connect to and click the Next button to continue. If the access point you wish to connect to does not appear here, click the Refresh button until it appears on the list, or try to move the Wireless Mesh Point closer to the access point you wish to connect to. 26 If you want to connect to a hidden access point, you can select "Setup repeater manually" to input the wireless setting manually. 5. Youll be prompted to input the access points wireless security key, input it in the KEY field and click the Next button to continue. 6. It will start to verify the wireless key with your associated access point and show you result within 20 seconds. Please follow the instructions to continue setup. 27 7. When the key is correct, this Wireless Mesh Point will display the connection information for you. 8. When you have setup dual band successfully (or setup single band manually), you will see the page below, press the Next button to continue. 28 If everything is correct, click the APPLY button to get connected. The Device SSID will be the same as the access points SSID you connected in this step. 9. Please wait a few moments for the Wireless Mesh Point to restart. 29 NOTE: After the wireless connection of this Wireless Mesh Point and wireless broadband router is built, the Wireless Mesh Point is DHCP client and will get an IP address from the broadband router automatically. If you want to login to the web user interface of the Wireless Mesh Point, please refer to 3.2 Repeater mode Advanced Settings for more functions or learn how to login to the web user interface again. 30 3.2 Repeater mode Advanced Settings 3.2.1 Connect to web configuration menu Open your web browser (IE, Firefox, Chrome etc.) and find the Wireless Repeaterxxxx Web UI firmware link on your bookmark list if you saved it when you installed this device for the first time. 10. Input http://192.168.2.252 in the address bar, then press the ENTER key:
NOTE: The default IP address of repeater mode is 192.168.2.252 The Wireless Mesh Point will prompt you to input the username and password. The default username is admin and password is 1234. Click the OK button to continue. 31 Detailed operation instructions will be given below. 32 3.2.2 Home The following information provides an overview of this Wireless Mesh Point. To access the Home menu, click Home on the left. You should see a screen that looks like this (the contents will vary depending on your actual settings):
33 You can click the Show Active Clients button to show all connected wireless clients. Please note: By clicking the Show Active Clients button, a new browser window will appear. If your browser prevents the pop-up window from appearing, please disable this function or you will not be able to use the Show Client function. 34 3.2.3 WPS Setting You can configure WPS (Wi-Fi Protected Setup) here. By using WPS, you can establish a secure connection between this Wireless Mesh Point and other wireless devices which also support WPS in a fast and secure manner. To access the WPS Setting menu, click WPS Setting on the left. The following setup page will appear:
The description of every setup item is listed as follows:
35 Item WPS Status Self PinCode SSID Description If the wireless security (encryption) function of this device is properly set, the WPS status will display Configured. If the wireless security function has not been set, the WPS status will display unConfigured. This displays an 8-digit number for WPS PIN-style configuration. When another WPS-compatible device wishes to connect to this Wireless Mesh Point and supports Self-PIN type WPS, input this number to the wireless device to establish connection. SSID stands for Service Set Identifier. All stations must be configured with the correct SSID to access the Wireless Network. Authentication Mode Shows the authentication mode of this Wireless Mesh Passphrase Key WPS Setting Start PBC Start PIN Point. This shows asterisks (*) to indicate that the wireless security is properly set. You can select which band (2.4G or 5G) you want to build the wireless connection via Start PBC button. Default is 2.4G. Click the Start PBC button to start the Push-Button style WPS setup procedure. This Wireless Mesh Point will wait for WPS requests from another wireless device for 2 minutes. The WPS LED on the Wireless Mesh Point will be blinking for 2 minutes when this Wireless Mesh Point is waiting for an incoming WPS request. Input the PIN code of the wireless client you wish to connect to, and the click Start PIN button. The WPS LED on the wireless Mesh Point will be blinking when this wireless Mesh Point is waiting for an incoming WPS request. NOTE: For WPS2.0 compliance specification, WEP and WPA-PSK cant support WPS connection; some of your wireless devices may follow this latest WPS2.0 specification, so we recommend not using WEP and WPA-PSK to avoid WPS interoperability problems. 36 3.2.4 Advanced Settings You can configure advanced wireless settings in this page. Please note that these settings are not safe to be configured by novice users. Configure these settings only when you understand what youre doing. To access the Advanced Settings menu, click Advanced Settings on the left. The following setup page will appear:
37 The description of every setup item is listed as follows:
Item Fragment Threshold RTS Threshold Beacon Interval DTIM Period Preamble Type Broadcast ESSID CTS Protect Description The threshold (number of bytes) of the fragmentation boundary for directed messages. It is the maximum data fragment size that can be sent. Input a value between 256 and 2346. Do not modify the default value if you dont know what it is. The default value is 2346. The RTS (Request To Send) threshold parameter controls what size data packet (number of bytes) the low level RF protocol issues to an RTS packet. The default is 2347. Do not modify the default value if you dont know what it is. The default value is 2347. The Beacon Interval value indicates the frequency interval of the beacon. Enter a value between 20 and 1000. A beacon is a packet broadcast by the Router to synchronize the wireless network. The default value is 100. Do not modify the default value if you dont know what it is. The default value is 100. Configures DTIM (Delivery Traffic Indication Message) send period. The default value is 3. The Preamble type defines the length of the CRC (Cyclic Redundancy Check) block for communication between the Access Point and roaming wireless adapters. Do not modify the default value if you dont know what it is. The default setting is Short Preamble. When set to enabled, every wireless device can scan and find this Wireless-N Range Mesh Point; when set to disabled, only wireless clients who know the exact SSID can get connected with this Wireless-N Range Mesh Point. Setting to disabled will help to improve security. This function provides CTS (Clear to Send) protection when transferring data. Selecting Auto for this option is recommended. 38 TX Power Enable LED off mode Select the wireless transmitting power level, from 10%
to 100%. When wireless clients are not too far from this Wireless-N Range Mesh Point, you dont have to select a higher power level, since this may cause some individuals to attempt to break into your wireless network if you have a bad password, or no password. You can enable or disable LED lights. Check Enable LED OFF mode to setup LED behavior:
Turn off all LED: disables all LED lights. Turn off all LED except POWER LED: all LED lights will be disabled, except the POWER LED. When you finish the settings in this page, click the Apply button. Youll see the following message:
if you want to save the changes and use it now, click the APPLY button. If you still need to configure this Wireless Mesh Point, click the CONTINUE button;
Youll be prompted to wait for 50 seconds before you can reconnect to this Wireless Mesh Point. After the countdown click the OK! button. 39 3.2.5 WLAN 2.4G settings To access the 2.4GHz Wireless menu, click WLAN 2.4G settings on the left. The following setup page will appear:
Please Note: If your Wireless Mesh Point is working properly, it is not recommended to make changes here. The description of every setup item is listed as follows:
Item Device SSID Description This is the current SSID name of the Mesh Point. The SSID is used to identify your own Mesh Point from others when there are other wireless devices in the same area. You can type any alphanumerical characters to change 40 Encryption WPA Unicast Cipher Suite the SSID here, maximum 32 characters. This is the current security setup of the Wireless Mesh Point. You can select an encryption method from the drop-down menu, there are three options. This is the current security setup of the Wireless Mesh Point. Please select a type of WPA cipher suite. Available options are: WPA (TKIP) and WPA2 (AES). You can select one of them, but you have to make sure your wireless client supports the cipher you selected. Pre-shared Key Format This is the current security setup of the Wireless Mesh Point. You can select the type of pre-shared key, you can select the Passphrase (8 or more alphanumerical characters, up to 63), or Hex (64 characters of 0-9, and a-f). This is the current security setup of the Wireless Mesh Point. You can change the WPA passphrase here. Its not recommended to use a word that can be found in a dictionary due to security reasons. This is the current channel of the Wireless Mesh Point. Key Channel 41 3.2.6 WLAN 5G settings To access 5GHz Wireless menu, click WLAN 2.4G settings on the left. The following setup page will appear:
Please Note: If your Wireless Mesh Point is working properly, it is not recommended to make changes here. The description of every setup item is listed as follows:
42 Item Device SSID Encryption WPA Unicast Cipher Suite Description This is the current SSID name of the Wireless Mesh Point. The SSID is used to identify your own Wireless Mesh Point from others when there are other wireless devices in the same area. You can type any alphanumerical characters to change the SSID here, maximum 32 characters. This is the current security setup of the Wireless Mesh Point. You can select an encryption method from the drop-down menu, there are three options. This is the current security setup of the Wireless Mesh Point. Please select a type of WPA cipher suite. Available options are: WPA (TKIP) and WPA2 (AES). You can select one of them, but you have to make sure your wireless client supports the cipher you selected. Pre-shared Key Format This is the current security setup of the Wireless Mesh Point. You can select the type of pre-shared key, you can select the Passphrase (8 or more alphanumerical characters, up to 63), or Hex (64 characters of 0-9, and a-f). This is the current security setup of the Wireless Mesh Point. You can change the WPA passphrase here. Its not recommended to use a word that can be found in a dictionary due to security reasons. This is the current channel of the Wireless Mesh Point. Key Channel 43 3.2.7 MAC Address Filtering Besides using wireless security to only allow permitted wireless users to use this Wireless Mesh Point, you can also use the MAC address filter to allow wireless users with certain MAC addresses to use this Wireless Mesh Point. This will enhance security because you can make a white list to allow users on the list to use this Wireless Mesh Point. Clients who arent listed on this white list, cant get connected, even if they know the password. To access the MAC Filtering menu, click MAC Filtering on the left. The following setup page will appear:
44 The description of every setup item is listed as follows:
Item Enable Wireless Access Control MAC Address Comment Add Clear Delete Selected Delete All Reset Select Description Check this box to enable MAC filtering. If you dont check this box, anyone who knows the wireless password can get connected to this Wireless Mesh Point. Input the MAC address of the clients you wish to deny or provide access to the Wireless Mesh Point into the MAC address list. Input 12 HEX characters here, you dont have to add : (colon) or - (dash) characters every 2 characters. If you dont know how to get the MAC address of a network client, see the following page. Input any descriptive text about this rule, so you can remember the purpose of this rule. You can input up to 20 alphanumerical characters in this field. Add this MAC address to the list. Clear MAC Address and Comment field. Delete MAC address(es) you selected. Delete all MAC addresses on the list. Youll be prompted to confirm the deletion first. Uncheck all checked boxes. All existing MAC addresses will be listed here. To delete a MAC address from the list, check the box of the MAC address you wish to delete first. You can select more than one MAC address here. When you complete the settings in this page, click the Apply button. Youll see the following message:
If you still need to configure this Wireless Mesh Point, click the CONTINUE button;
if you want to save the changes and use it now, click the APPLY button. Youll be prompted to wait for 50 seconds before you can reconnect to this Wireless Mesh Point. 45 3.2.8 How to find the MAC address of your device If you dont know the MAC address of your computer or wireless device, you can follow the procedure below:
For wireless devices and computers which are connected to this Wireless Mesh Point already, you can click the Show Active Clients button on the Home setting page. Their MAC address will be displayed in the MAC Address field. If you still cant identify the MAC address of your computer, you can follow this procedure:
Go to your computers Control Panel, Then click Network and Sharing Center. 46 Click the connection that will be used to connect the Wireless Mesh Point (in this example, ofiice):
Click the Details button. 47 The MAC address of the selected network connection will be displayed here as Physical Address. 48 49 3.2.9 System Utility You can change the settings of several system-level parameters in this page, including the administrators password, and the IP address. To access the System Utility menu, click System Utility on the left. The following setup page will appear:
The description of every setup item is listed as follows:
50 Password Settings The default password of this Wireless Mesh Point is 1234, and its displayed on the login prompt when accessed from the web browser. Theres a security risk if you dont change the default password, since everyone can see it. This is very important when you have the wireless function enabled. Here are descriptions of every setup item:
Item Current Password New Password Description To change the password, you have to input the current password first. Input the new password here. You can use the combination of letters, numbers, and symbols up to 20 characters. Input the new password again for conformation. Re-Enter Password When you complete the settings in this page, click the Apply button. Youll see the following message:
If you still need to configure this Wireless Mesh Point, click the CONTINUE button;
if you want to save the changes and use it now, click the APPLY button. Youll be prompted to wait for 50 seconds before you can reconnect to this Wireless Mesh Point. 51 3.2.10 Configuration You can backup and restore the configuration of this Wireless Mesh Point, so you can recall all settings, without the need to reconfigure again. This function is especially useful when you need to use this mini Wi-Fi Mesh Point in different places, like your home and hotels. To access the Configuration menu, click Configuration on the left. 3.2.10.1 Configuration Tool The following setup page will appear:
The description of every setup item is listed as follows:
52 Item Backup Settings Restore Settings Reset to Factory Default Description Click the Save button to save the current settings to a file on your computer. If you want to upload a saved configuration file to the Wireless Mesh Point, click the Browse button to select a saved configuration file on your computer. Then click the Upload button to replace the current settings. To reset all settings of this Wireless Mesh Point to factory defaults, including the password. Youll be prompted to confirm the settings reset:
Click OK if you really want to restore all settings, or click Cancel to abort. 53 3.2.10.2 WEB Upgrade The software running on this Wireless Mesh Point (i.e. Firmware) can be upgraded to improve the functionality of this Wireless Mesh Point. You can access our website to look for the latest firmware file. Then download the latest firmware file and save on your computer and upload to this Wireless Mesh Point. The description of every setup item is listed as follows:
Item Description Select a firmware file saved on your computer. Browse When you are ready, click the Apply button to start the firmware upgrade procedure. 54 3.2.10.3 Reset In the event that the system stops responding correctly or stops functioning, you can perform a standard Reset or Reset to Defaults. A standard Reset will retain your settings and reboot the Wireless Mesh Point, while resetting the device to defaults will erase all configuration settings. To reset this Wireless Mesh Point, click the Apply button. Youll be prompted to confirm the reset:
Click the OK button to reset the Wireless Mesh Point, or click Cancel to abort. 55 Chapter 4 AP Mode You can build a wireless networking environment for the home or small office. Then your wireless client users can access Internet by wirelessly connecting to this AP without wired cable burden. This chapter will show you how to quickly install this device by using quick setup and explain each detailed setting on the web user interface page of AP mode. 4.1 AP Mode Quick Installation Guide 1. Connect this access point to an ADSL/VDSL modem, wired router, or switch/hub in your network through the LAN port of the access point by Ethernet cable. The quick installation setup is complete, you can refer to 4.2 AP mode Advanced Settings to login to the web user interface for other advanced 56 settings. 4.1.2 Web browser quick setup Before you can connect to the Wireless Mesh Point and start configuration procedures, your computer must be able to get an IP address automatically (use dynamic IP address). If its set to use static IP address, or youre unsure, please refer to Chapter 6: 6.1 Configuring TCP/IP on PC to set your computer to use a dynamic IP address. 1. Use an Ethernet cable to connect your computers Ethernet port and Wireless Mesh Points Ethernet port. Or use your computers wireless configuration utility to search for an access point named repeater0003 and get connected. (The default SSID of this Wireless Mesh Point device is repeater0003, 0003 is a reference, it is the last 4 digits of the devices MAC number. Each device has a different MAC number, please find it on your device label.) 57 NOTE: this default SSID repeater0003 is for reference, different devices may have different last 4 digits. If you are using a wireless connection in Windows Operating System and encountered the following screen, please click Connect the network without setting it up then you can successfully link to the Wireless Mesh Point. Do NOT click OK . In case you click OK, the Windows Operating System will ask for a security key, please click Cancel to revert back to this page. 2. Open your web browser, it will redirect to the web user interface setting page.
(or you can input the default IP address http://192.168.2.252 in the address bar) 3. The Wireless Mesh Point will prompt you to input the username and password. Default username is admin and password is 1234. Click the OK button to continue. 58 4. Please input an SSID (a name used to identify this access point) in the Device SSID(2.4GHz) and Device SSID(5GHz) field, then click the Next button. The default SSID is repeaterxxxx, you can change this default SSID if you want. 5. Select security type of the wireless link to include 2.4Ghz and 5Ghz :
Encryption: Disable (no security), WEP, WPA pre-shared key, or WPA RADIUS. 59 2.4GHz Wireless 5GHz Wireless Note: WEP encryption: Select key length (64 or 128bit), key format (Hex or ASCII characters), Default Tx Key (usually use Key 1), and input key characters (refer to Key Format you selected for number of characters). WPA pre-shared key: Select one WPA Unicast Cipher Suite (usually use default setting WPA(TKIP)), Pre-shared Key Format: Passphrase
(alphanumeric characters) or Hex (64 Hex Characters), and input key characters in the KEY field. WPA RADIUS: Only use this option if you have a RADIUS authentication server on your LAN. You have to input the RADIUS servers parameters
(Server IP, port number, and password). 60 6. Please recheck the settings you made, and click Apply to continue. 7. Please wait for few seconds for device to reboot. 8. After reboot is complete, you can close the browser to finish this quick setup and connect this access point to an ADSL modem, wired router, or switch/hub in your network through the LAN port of the access point by Ethernet cable. NOTE: After quick installation is successful and you want to login to the web user interface of the Wireless Mesh Point, please refer to 4.2 AP mode Advanced Settings for more functions or learn how to login to the web user interface again. 61 4.2 AP Mode Advanced Settings 4.2.1 Connect to web configuration menu 11. Please open your web browser (IE, Firefox, Chrome etc.) and input http:/ 192.168.2.252 in the address bar, then press the ENTER key:
The Wireless Mesh Point will prompt you to input the username and password. The default username is admin and password is 1234. Click the OK button to continue. You should be able to see the configuration page of this Access Point mode in a very short time:
Detailed operation instructions will be given below. 62 4.2.2 Home The status and information of this access point will be displayed here. To access the Home menu, click Home on the left. You should see the following (the contents will vary depending on your actual setting):
63 You can click the Show Active Clients button to show all connected wireless clients. Please note: By clicking the Show Active Clients button, a new browser window will appear. If your browser prevents a pop-up window from appearing, please disable this function or you will not be able to use the Show Client function. 64 4.2.3 WPS Setting You can configure WPS (Wi-Fi Protected Setup) here. By using WPS, you can establish a secure connection between this Wireless Mesh Point and other wireless devices which also support WPS in a fast and secure manner. To access the WPS Setting menu, click WPS Settings on the left. The following setup page will appear:
65 The description of every setup item is listed as follows:
Item WPS Status Self PinCode Description Shows the security setting status of WPS. If the wireless security (encryption) function of this device is properly set, youll see the Configured message here. If the wireless security function has not been set, youll see unConfigured. This displays an 8-digit number for WPS PIN-style configuration. When another WPS-compatible device wishes to connect to this Wireless Mesh Point and supports Self-PIN type WPS, input this number to the wireless device to establish connection. Shows the SSID of this Wireless Mesh Point. SSID Authentication Mode Shows the authentication mode of this Wireless Mesh Passphrase Key WPS Setting Start PBC Start PIN Point. This shows asterisks (*) to indicate wireless security is properly set. You can select which band(2.4G or 5G) you want to build wireless connection via the Start PBC button. Default is 2.4G. Click the Start PBC button to start the Push-Button style WPS setup procedure. This Wireless Mesh Point will wait for WPS requests from another wireless device for 2 minutes. The WPS LED on the Wireless Mesh Point will be blinking for 2 minutes when this Wireless Mesh Point is waiting for an incoming WPS request. Please input the PIN code of the wireless client you wish to connect, and click the Start PIN button. The WPS LED on the Wireless Mesh Point will be blinking when this Wireless Mesh Point is waiting for an incoming WPS request. NOTE: For WPS2.0 compliance specification, WEP and WPA-PSK cant support WPS connection, some of wireless devices may follow this latest WPS2.0 specification, so we recommend not using WEP and WPA-PSK to avoid WPS interoperability problems. 66 4.2.4 Advanced Settings You can configure advanced wireless settings in this page. Please note that these settings are not safe to be configured by novice users. Configure these settings only when you understand what youre doing. To access the Advanced Settings menu, click Advanced Settings on the left. The following setup page will appear:
67 The description of every setup item is listed as follows:
Item Fragment Threshold RTS Threshold Description Set the Fragment threshold of wireless radio. Do not modify the default value if you dont know what it is. The default value is 2346. Set the RTS threshold of wireless radio. Do not modify the default value if you dont know what it is. The default value is 2347. 68 Beacon Interval DTIM Period Channel Width Preamble Type Broadcast ESSID WMM CTS Protect TX Power Enable LED off mode Set the beacon interval of wireless radio. Do not modify the default value if you dont know what it is. The default value is 100. Configures DTIM (Delivery Traffic Indication Message) send period. The default value is 3. Set channel width of wireless radio. You can modify the default value if you know what channel width you need, default setting is Auto 80MHz. Set the type of preamble of wireless radio. Do not modify the default value if you dont know what it is. The default setting is Short Preamble. When set to enabled, every wireless device can scan and find this Wireless Mesh Point; when set to disabled, only wireless clients who know the exact SSID can get connected with this wireless Mesh Point. Set to disabled will help to improve security. Enable or disable Wireless Multi-Media. When enabled, the Wireless Mesh Point will give priority to multimedia related network applications so they will have better performance. This function provides CTS (Clear to Send) protection when transferring data. Its recommended to select Auto for this option. Select the wireless transmitting power level, from 10%
to 100%. When wireless clients are not too far from this Wireless Mesh Point, you dont have to select a higher power level, since this may cause some individuals to attempt to break into your wireless network if you have a bad password or no password. You can enable or disable LED lights. Check Enable LED OFF mode to setup LED behavior:
Turn off all LED: disables all LED lights. Turn off all LED except POWER LED: all LED lights will be disabled, except the POWER LED. When you complete the settings in this page, click the Apply button. Youll see the following message:
69 If you still need to configure this Wireless Mesh Point, click the CONTINUE button;
if you want to save the changes and use it now, click the APPLY button. Youll be prompted to wait for 50 seconds before you can reconnect to the web user interface of this access point. After the countdown click the OK! button. 70 4.2.5 WLAN 2.4G settings To access the 2.4GHz Wireless menu, click WLAN 2.4G settings on the left. The following setup page will appear, it is the settings that you have setup:
Please Note: If your Wireless Mesh Point is working properly, please do not change the settings here. The description of every setup item is listed as follows:
71 Item Device SSID Encryption WPA Unicast Cipher Suite Description This is the current SSID name of the Wireless Mesh Point. The SSID is used to identify your own Wireless Mesh Point from others when there are other wireless devices in the same area. You can type any alphanumerical characters to change SSID here, maximum 32 characters. This is the current security setup of the Wireless Mesh Point. You can select an encryption method from the drop-down menu, there are three options. This is the current security setup of the Wireless Mesh Point. Please select a type of WPA cipher suite. Available options are: WPA (TKIP) and WPA2 (AES). You can select one of them, but you have to make sure your wireless client supports the cipher you selected. Pre-shared Key Format This is the current security setup of the Wireless Mesh Key Channel Point. You can select the type of pre-shared key, you can select the Passphrase (8 or more alphanumerical characters, up to 63), or Hex (64 characters of 0-9, and a-f). This is the current security setup of the Wireless Mesh Point. You can change the WPA passphrase here. Its not recommended to use a word that can be found in a dictionary due to security reasons. This is the current channel of the Wireless Mesh Point. 72 4.2.6 WLAN 5G settings To access the 5GHz Wireless menu, click WLAN 5G settings on the left. The following setup page will appear, it is the settings that you have setup:
Please Note: If your Wireless Mesh Point is working properly, please do not change the settings here. The description of every setup item is listed as follows:
73 Item Device SSID Encryption WPA Unicast Cipher Suite Description This is the current SSID name of the Wireless Mesh Point. The SSID is used to identify your own Wireless Mesh Point from others when there are other wireless devices in the same area. You can type any alphanumerical characters to change the SSID here, maximum 32 characters. This is the current security setup of the Wireless Mesh Point. You can select an encryption method from the drop-down menu, there are three options. This is the current security setup of the Wireless Mesh Point. Please select a type of WPA cipher suite. Available options are: WPA (TKIP) and WPA2 (AES). You can select one of them, but you have to make sure your wireless client supports the cipher you selected. Pre-shared Key Format This is the current security setup of the Wireless Mesh Point. You can select the type of pre-shared key, you can select the Passphrase (8 or more alphanumerical characters, up to 63), or Hex (64 characters of 0-9, and a-f). This is the current security setup of the Wireless Mesh Point. You can change the WPA passphrase here. Its not recommended to use a word that can be found in a dictionary due to security reasons. This is the current channel of the Wireless Mesh Point. Key Channel 4.2.7 MAC Address Filtering Besides using wireless security to only allow permitted wireless users to use this wireless access point, you can also use the MAC address filter to allow wireless users with certain MAC addresses to use this access point. This will enhance security because you can make a white list to allow users on the list to use this Wireless Mesh Point. Clients who arent listed on this white list, they cant get connected, even if they know the password. 74 To access the MAC Filtering menu, click MAC Filtering on the left. The following setup page will appear:
The description of every setup item is listed as follows:
Item Enable Wireless Access Control MAC Address Description Check this box to enable MAC filtering. If you dont check this box, anyone who knows the wireless password can get connected to this access point. Input the MAC address of the clients you wish to deny or provide access to this AP into the MAC address list. Please input 12 HEX characters here, you dont have to add : (colon) or - (dash) characters every 2 characters. 75 Comment Add Clear Delete Selected Delete All Reset Select If you dont know how to get the MAC address of a network client, see the following page. Input any descriptive text about this rule, so you can remember the purpose of this rule. You can input up to 20 alphanumerical characters in this field. Add this MAC address to the list. Clear MAC Address and Comment field. Delete MAC address(es) you selected. Delete all MAC addresses on the list. Youll be prompted to confirm deletion first. Uncheck all checked boxes. All existing MAC addresses will be listed here. To delete a MAC address from the list, check the box of the MAC address you wish to delete first. You can select more than one MAC address here. Click the Apply button. Youll see the following message:
If you still need to configure this Wireless Mesh Point, click the CONTINUE button;
if you want to save the changes and use it now, click the APPLY button. Youll be prompted to wait for 50 seconds before you can reconnect to this access point. TIPS: If you dont know the MAC address of your computer or wireless device, you can the procedure below:
For wireless devices and computers which are connected to this Wireless Mesh Point already, you can click the Show Active Clients button on the Home setting page. 76 Their MAC address will be displayed in the MAC Address field. 4.2.8 How to know the MAC address of your device If you still cant identify the MAC address of your computer, you can follow this procedure:
Go to your computers Control Panel, Then click Network and Sharing Center. Click the connection that will be used to connect the wireless AP (in this example, Local Area Connection):
77 Click the Details button. The MAC address of selected network connection will be displayed here as Physical Address. 78 79 4.2.9 System Utility You can change the settings of several system-level parameters in this page, including the administrators password, and IP address. To access the System Utility menu, click System Utility on the left. The following setup page will appear:
The description of every setup item is listed as follows:
80 4.2.9.1 Password Settings The default password of this Wireless Mesh Point is 1234, and its displayed on the login prompt when accessed from the web browser. Theres a security risk if you dont change the default password, since everyone can see it. This is very important when you have the wireless function enabled. Here are descriptions of every setup item:
Description To change the password, you have to input the current password first. Input the new password here. You can use the combination of letters, numbers, and symbols up to 20 characters. Input the new password again for conformation. Item Current Password New Password Re-Enter Password 81 4.2.10 Configuration You can backup and restore the configuration of this access point, so you can recall all settings, without the needing to reconfigure again. This function is especially useful when you need to use this mini Wi-Fi AP in different places, like your home and hotels. To access the Configuration menu, click Configuration on the left. 4.2.10.1 Configuration Tool The following setup page will appear:
The description of every setup item is listed as follows:
82 Item Description Backup Settings Click the Save button to save the current settings to a file on Restore Settings Reset to Factory Default your computer. If you want to upload a saved configuration file to this device, please click the Browse button to select a saved configuration file on your computer. Then click the Upload button to replace the current settings. To reset all settings of this device to factory defaults, including the password. Youll be prompted to confirm the settings reset:
Click OK if you really want to restore all settings, or click Cancel to abort. 4.2.10.2 WEB Upgrade The software running on this device (i.e. Firmware) can be upgraded to improve the functionality of this access point. You can access our website to look for the latest firmware file. Then download the latest firmware file and save on your computer and upload to this wireless AP. 83 The description of every setup item is listed as follows:
Item Description Select a firmware file saved on your computer. Browse When you are ready, click the Apply button to start the firmware upgrade procedure. 4.2.10.3 Reset When you think this wireless AP is not working properly, resetting it may help. To reset this Wireless Mesh Point, click the Apply button. Youll be prompted to confirm the reset:
Click the OK button to reset the Wireless Mesh Point, or click Cancel to abort. 84 Chapter 5 Appendix 5.1 Configuring TCP/IP on PC 5.1.1 Windows XP IP address setup:
1. Click the Start button (it should be located at the lower-left corner of your computer screen), then click control panel. Double-click Network and Internet Connections icon, and then click Network Connections, then double-click Local Area Connection, the Local Area Connection Status window will appear, and then click the Properties button. 2. Select Obtain an IP address automatically and Obtain DNS server address automatically, then click the OK button. 85 5.1.2 Windows Vista/Windows 7 IP address setup:
1. Click the Start button (it should be located at lower-left corner of your computer screen), then click control panel. Click View Network Status and Tasks, and then click Manage Network Connections. Right-click Local Area Network, then select Properties. The Local Area Connection Properties window will appear, select Internet Protocol Version 4 (TCP / IPv4), and then click the Properties button. 86 2. Select Obtain an IP address automatically and Obtain DNS server address automatically, then click the OK button. 87 88
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2018-12-30 | 2412 ~ 2462 | DTS - Digital Transmission System | Original Equipment |
2 | 5725 ~ 5850 | NII - Unlicensed National Information Infrastructure TX |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 | Effective |
2018-12-30
|
||||
1 2 | Applicant's complete, legal business name |
Comtrend Corporation
|
||||
1 2 | FCC Registration Number (FRN) |
0010188456
|
||||
1 2 | Physical Address |
3F-1, 10 Lane 609, Chung Hsin Road, Section 5
|
||||
1 2 |
New Taipei City,, N/A 24159
|
|||||
1 2 |
Taiwan
|
|||||
app s | TCB Information | |||||
1 2 | TCB Application Email Address |
v******@tuvsud.com
|
||||
1 2 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 2 | Grantee Code |
L9V
|
||||
1 2 | Equipment Product Code |
WAP5922
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 | Name |
B******** W******
|
||||
1 2 | Telephone Number |
+886-********
|
||||
1 2 | Fax Number |
+886-********
|
||||
1 2 |
b******@comtrend.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 2 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 2 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 | Equipment Class | DTS - Digital Transmission System | ||||
1 2 | NII - Unlicensed National Information Infrastructure TX | |||||
1 2 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | AC1200 Wifi Extender / AC1200 Wireless Mesh Point / AC1200 Wireless Extender | ||||
1 2 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 2 | Modular Equipment Type | Does not apply | ||||
1 2 | Purpose / Application is for | Original Equipment | ||||
1 2 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | Yes | ||||
1 2 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 2 | Grant Comments | Output power is conducted. This device has 20 and 40 MHz BW modes. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons. End users must be informed of the requirements for satisfying RF Exposure compliance. | ||||
1 2 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 | Firm Name |
SGS Taiwan Ltd.
|
||||
1 2 | Name |
R******** W****
|
||||
1 2 | Telephone Number |
+886-******** Extension:
|
||||
1 2 | Fax Number |
+886-********
|
||||
1 2 |
R******@sgs.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | CC MO | 2412.00000000 | 2462.00000000 | 0.4900000 | |||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 15E | CC MO | 5150 | 5250 | 0.057 | |||||||||||||||||||||||||||||||||||
2 | 2 | 15E | CC MO | 5725 | 5850 | 0.189 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC