User manual Introduction Congratulations on receiving your CY-WB1900-A1. As part of our Green Initiative, we do not include printed user documentation with our product packaging. This policy saves paper, lowers shipping costs, reduces carbon emissions and results in a cleaner environment. Documentation All product and accessory documentation can be found at the GLI Support Centre: http://www.gl-inet.com/docs On this site you will gain access to GLI technical resources and information about GLI products. To use your new GLI Mini Router you will need to follow the simple steps which you can see from http://www.gl-inet.com/docs/wiki/#!mini/index.md Default System Settings Product CY-WB1900-A1 Initial Set-up Interfaces described as followed:
LAN Default IP Address LAN Fall-back IP Address DHCP 192.168.8.1 Power to the GLI Mini Router is provided by connect the power lead (supplied) to the power adaptor (buy separately) and then to the power interface on the GLI Mini Router. Once power is provided to the GLI Mini Router the LEDs will provide status on its operation based on the following:
LED LED 1 (Power) LED 2 (Customized) LED 3 (WiFi connection) Indicator Green solid Customized Red Description Power is applied This is customized LED. Indicates WiFi signal (solid) and data transfer (flashing). Button Definition Press the Reset button to toggle the WiFi signal ON or OFF. Press and hold the Reset button for at least 8 seconds, then release your finger to reset the router to factory default state. Wait until the router reboots, which could take about 3 minutes. The function of switch is configurable by user. FCC Statement 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC Caution Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. WARNNING: The minimum separation generally be used is at least 20 cm, even if the calculations indicate that the MPE distance would be lesser. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
(1) L' appareil ne doit pas produire de brouillage;
(2) L' appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d' en compromettre le fonctionnement. Radio Frequency Exposure Statement for IC The device has been evaluated to meet general RF exposure requirements. The device can be used in mobile exposure conditions. The min separation distance is 20cm. Dclaration d'exposition aux radiofrquences pour IC Lappareil a t utilis pour rpondre aux exigences gnrales en matire dexposition aux radiofrquences.