FCC ID: 2AJW5ACCM Telematic system

WARRANTY The customer shall benefit from the legal warranty against latent defects as specified in sections 1641 to 1649 of the Belgian Civil Code if the latent defect exists at the time of delivery and if the latent defect makes the unit unfit for the use for which it was designed or substantially reduces its use. Latent defects must be notified by registered letter to Continental within one month from the time the customer discovers it or ought reasonably to have discovered it. If the customer is a consumer, Continental shall be liable to the customer for any non-conformity which exists at delivery and appears within two years thereof. Any non-conformity shall be notified by registered letter to Continental within one month from the time the customer discovers it. DISCLAIMER The information in this document is subject to change without notice and does not represent a commitment on the part of the vendor. No warranty or representation, either expressed or implied, is made with respect of quality, accuracy or fitness for any particular purpose of this document. Without written permission from Continental, any forms of reproduction, spreading, distribution are prohibited. Continental reserves the rights to modify or improve the product without any prior notification. In no event will the supplier be liable for direct, indirect or special, incidental or consequential damages arising out of the user or inability to use this product or documentation, even if advised of the possibility of such damages. This document contains materials protected by copyright.

INTRODUCTION Access and Connected Car Module (ACCM) Access and Connected Car Module PLUS (ACCM+) INSTALLATION GUIDE (June 2021) BLUETOOTH The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Continental is under license. Other trademarks and trade names are those of their respective owners. Continental is a virtual key enabler. the Car & Connected Car Module - ACCM and the Car & Connected Car Module PLUS ACCM+ allow vehicle access, authorization to start and vehicle data for any vehicle fleet management type CE Hereby, Continental declares that this Car & Connected Car Module is compliant with essential requirements and other relevant provisions of directive 2014/53/EU. The ACCM can be operated in at least one Member State without infringing applicable requirements on the use of a radio spectrum FCC (FEDERAL COMMUNICATIONS COMMISSION) WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. The device complies with Part 15 of FCCs rules. Operation is subject to the following two conditions: (i) this device may not cause harmful interference and (ii) this device must accept any interference received, including interference that may cause undesirable operation. MANUAL REQUIREMENTS ACCORDING 15.19/RSS-GEN This device complies with Part 15 of the FCC Rules [and with Industry Canada licence-exempt RSS standard(s)]. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. MANUAL REQUIREMENTS ACCORDING 15.21 Changes or modifications made to this equipment not expressly approved by Continental Automotive GnbH may void the FCC authorization to operate this equipment. FCC RF EXPOSURE REQUIREMENTS This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. CORRECT DISPOSAL OF THIS PRODUCT (WASTE ELECTRICAL AND ELECTRONICS EQUIPMENT) This marking shown on the product or its literature indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly. COPYRIGHTS Copyright 2015 Continental. All rights reserved. No part of this manual may be reproduced or transmitted in any means or for any purpose without the express written content of Continental. All trademarks, product names appearing in this document are registered property of their respective owners. 12Vcc Specification Electric Power Consumption in stand-by mode < 8 mA Operating temperature Dimensions Weight Data transmission

- 25C + 55C 131.6 x 61 x 37.6 mm 130g Bluetooth and LTE (US version only) Content of the box 1 ACCM or ACCM+

1 Power cable (OBDII connector) ANTENNA FREQUENCY AND MAX POWER Communication protocols Antenna Allowable bands Uplink and Downlink Frequencies

(MHz) Max Power

(dBm) BLE band 2

(1900MHz) band 4

(1700MHz) band12

(700MHz) band 3

(1800MHz) band 7

(2600MHz) band 20

(800MHz) UL DL UL DL UL DL UL DL UL DL UL DL 2402 ~ 2480 1850 ~ 1910 1930 ~ 1990 1710 ~ 1755 2110 ~ 2155 699 ~ 716 729 ~ 746 1710 ~ 1785 1805 ~ 1880 2500 ~ 2570 2620 ~ 2690 832 ~ 862 791 ~ 821 4.08 23 4G LTE North America LARA-R203 EMEA LARA-R211 For ACCM + only:

Communication protocols SRD SRD SRD SRD Frequencies (MHz) 313.5 ~ 315.3 433.5 ~ 434.3 868 ~ 868.5 902.3 ~ 903.3 Max Power ( dBm)

-22.5

-22.5

-20.5

-20.5 WARNING Continental S.A and its affiliates should not be held liable towards end-users for third parties prejudice caused by misusage of the product. We advise our customers to have the ACCM fitted by a professional. The cable length is sufficient to connect later every element: power cable and antenna Continental is not responsible for the damage caused to the vehicle and/or accessories with We advise our customers to have the ACCM fitted by a professional. Never remove the cover of the ACCM or ACCM+. Before you install the individual components, check that the installation area has been Do not install any component in the airbag deployment area. Do not install the ACCM or ACCM+ against a large metal surface in the car. Once the installation is completed, make sure that no cables are pinched or trapped. In case you would like to buy additional keys and have them programmed to the vehicles BEFORE YOU BEGIN selected in such a way that:

(if necessary) for a car equipped with a keyless start system, the location where you plan to install the ACCM must be within the reception area of the keyless system of the car. Use therefore the original key and place it at the chosen installation area and check immediately that the engine can be started. immobilizer system in the future, some manufacturers require that all original keys are present in the car to be able to get an additional key. It will be necessary that you participate in the coding of the new key with a virtual key being active and connected to the car to perform the actions required by the dealer. are the results of a non-respect of the instructions of this manual. IMPORTANT REMARKS Installation steps 1 and 2 (see below) must only be performed for cars not equipped with a keyless start Placing the ACCM or ACCM+ under or next to any large metal surface or an airbag could affect the reception of the ACCM. With the keyless start system, the vehicle doors can be opened without need for the driver to physically push a button on the key fob to lock or unlock the doors. To start or to stop the engine, there is no need to insert a key in the barrel to turn on the ignition. system. If the car is equipped with a keyless system, go directly to step 3. INSTALLATION STEPS:

Disconnect the battery of the car. 1. Disassemble the shroud for easy access to the vehicles ignition switch. Pull the steering wheel in your direction to its maximum.

Place the ring of the antenna around the vehicles ignition switch as shown below. 2. Fix and tape the ring around the ignition, excess cable can be taped together but may not be turned around (one rotation maximum). When using the ring method for installing the ACCM or ACCM+ the ring MUST be taped in front of the factory receiver ring. It CAN NOT be on top of, or behind the factory receiver ring. See illustration above. The antenna cable must follow existing steering column cables to avoid rupture while closing the shroud or moving the steering wheel. Reassemble the shroud. 3. Connect now the ACCM to the OBDII connector in the car. The OBD port is generally located in the driver cabin, between the door and the steering column. 4. Place the NFC reader (optional) on the bottom left corner of the windscreen. Use the provided sticker and tape to fix the reader on the windscreen. Place the sticker on the windscreen and use the tape to fix the reader on the sticker. The white side of the reader must be faced to the car. For your convenience, you can also decide to place the reader on the top left corner of the windscreen. 5. Reconnect the vehicle battery. Validate that the ACCM or ACCM+ has a power connection (LEDs on side). You are now ready 6. to test the ACCM with a virtual key on a smartphone equipped with the Continental mobile application. 7. Fix the ACCM or ACCM+ behind the dashboard. Manufactured by: AMOTECH Address: 5BL-1LOT, 380, Namdongseo-ro, Namdong-gu, Incheon, Korea 21629

file: Label specification _ V13.1_update20220111 11.01.2022

- NEW ACCM v6 sheets ( 1 for ACCM+ using RCK gen 1 and one ACCM+ using RCK Gen 2)

- OTA keys name removed Space for IC number for all modules V5 or V6 This document is a visual presentation of the label content and it is not showing the right format nor can be used to test the readibility of the labels. ACCM LABELS SPECIFICATION WARNING Author: G. VALLET Version: V13

ACCM or ACCM+

ACCM or ACCM+

ACCM Box (inner box) ACCM +

Model:

P/N:

Lot:

FCC ID:

IC:

Continental ITS ACCM201-US4G-1B TRC0304930001 Lot 2AJW5ACCM 21979-ACCM 4 9 mm Serial No.

"S/N:" Serial No. 12,0 V 1,0 A Contains FCC ID: M3NRCKF2B, IC: 7812A-RCKF2B Emark: number Produced by Amotech, Korea This information is only for ACCM version, not for ACCM+ variant. ACCM is not a part of the certification. ACCM side label 4 9 mm IMEI

"IMEI:" IMEI ( Cellular Radio ID) ACCM +

Model:

P/N:

Lot:

FCC ID:

IC:

Continental ITS Model name Continental P/N Lot ACCM FCC ID number ACCM IC ID number Contains FCC ID: M3NRCKF2B, IC: 7812A-RCKF2B 12,0 V 1,0 A Emark: number Produced by Amotech, Korea This information is only for ACCM version, not for ACCM+ variant. ACCM is not a part of the certification. 1 0 mm 1 0 mm AVIS VERSION ACCM Top label Property of Avis Budget Group -

Reward for Return: conti.returns@abg.com

"SIM": SIM No. : ICCID Contains FCC ID: QOQBGM12LMA ; IC: 5123A-BGM12LMA Contains FCC ID: XPY1DIQN3NN ; IC: 8595A-1DIQN3NN For all versions BLE FCC and IC ID Modem FCC and IC ID GENERIC VERSION 5 0 mm Serial No.

"S/N": serial No SIM No. 5 0 mm Serial No.

"S/N": serial No SIM No. Serial No. 1 8 mm Serial No. 1 8 mm Contains FCC ID: QOQBMG12LMA ; IC: 5123A-BMG12LMA Contains FCC ID: XPY1DIQN3NN ; IC: 8595A-1DIQN3NN

"SIM": SIM No. : ICCID For all versions BLE FCC and IC ID Modem FCC and IC ID Definitions / Naming Conventions BOX INFO

B tracking info Year Month Day n box in Palette Amotech specifiic Modules versions

Serial Number

A C C M y y y y x x x x x x x x x x x x to be read from the ACCM with yyyyxxxxxxxxxxxx from UUID where UUID = zzzzzzzz-zzzz-zzzz-yyyy-xxxxxxxxxxxx Definitions Continental P/N =

TRC number on for each part version LOT tracking information Year Month Day Lot part 1 8 0 3 2 8 0 1 0 0 0 1 LOT INFO L tracking info Year Month Day Lot 1 8 0 3 2 8 0 1 1 lots is 600 parts 1 8 0 3 2 8 0 1 0 9 9 1 palette has 108 boxes Cellular Radio ID =

IMEI to be read from the ACCM SIM No FCC ID FCC certification number ICCID to be read from the ACCM information on RCK FCC ID and IC:

Contains FCC ID: M3N-RCKF, IC: 7812A-RCKF Part Number Model Number TRC0304870000ACCM101-EU4G-00 TRC0304880000ACCM201-EU4G-1A TRC0304890000ACCM201-EU4G-1B TRC0304900000ACCM201-EU4G-2C TRC0304910001ACCM101-US4G-00 TRC0304920001ACCM201-US4G-1A TRC0304930001ACCM201-US4G-1B TRC0304940001ACCM201-US4G-2C Description ACCM using retrofit Key EU 4G ACCM+ RCK Daughter Board Type 1A (Ford) US 4G ACCM+ RCK Daughter Board Type 1B EU 4G ACCM+ RCK Daughter Board Type 2C EU 4G ACCM using retrofit Key US 4G ACCM+ RCK Daughter Board Type 1A (Ford) US 4G ACCM+ RCK Daughter Board Type 1B US 4G ACCM+ RCK Daughter Board Type 2C US 4G Module Naming convention Module Naming convention Access and Connected Car Module Access and Connected Car Module PLUS V6 V6 ACCM101 ACCM201 REGION:

EU US Europe USA 3G (no longer used with ACCM v6) 4G-> TLE CAT 1 Technology 3G 4G Key device 00 1A with RCK GEN1 - Ford RCK ID = RCKF03-WWYY-XXXX-XXXX 1B with RCK GEN1 - other RCK ID = RCKF04-WWYY-XXXX-XXXX 2C with RCK GEN 2 Daughter board for US and EU markets retrofit Key ACCM101-EU4G-00 ACCM201-EU4G-1A ACCM201-EU4G-1B ACCM201-EU4G-2C ACCM101-US4G-00 ACCM201-US4G-1A ACCM201-US4G-1B ACCM201-US4G-2C ACCM101-EU4G-00 Modules versions vs Continental P/N TRC0304870000

ACCM201-EU4G-1A TRC0304880000 ACCM201-EU4G-1B ACCM201-EU4G-2C TRC0304890000 TRC0304900000 ACCM101-US4G-00 TRC0304910001 ACCM201-US4G-1A TRC0304920001 ACCM201-US4G-1B TRC0304930001 ACCM201-US4G-2C TRC0304940001

Author: G. VALLET

@OTA keys - confidential 1/2 file: Label specification _ V13.1_update20220111 11.01.2022 BOX LABEL (outer box) 1 0 0 mm AMOTECH.CO., LTD for CONTINENTAL ITS 1. Part Name: Access and Connected Car Module PLUS 3 0 mm 2. Part No: ACCM201-US4G-2C 3. Continental P/N: TRC0304940001 4. Box No: B19140301099 5. Lot Info: L190325-01 L190326-02 6: Qty: 24 (ACCM+) or 30(ACCM) All parts Serial No. 3 0 mm QR CODE FORMAT All parts Serial No. 1 7 5 mm All parts Author: G. VALLET

@OTA keys - confidential 2/2

LONG-TERM CONFIDENTIALITY REQUEST for Certification Service in the USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 TO WHOM IT MAY CONCERN Pursuant to Paragraphs 0.457 and 0.459 of the Commissions Rules (47 C.F.R.) and Section 552(b)(4) of the Freedom of Information Act, we request Long-Term Confidentiality for the following product:

Grantee Code Equipment Product Code Check your GC here. Click Grantee Search. FCC ID:

For the product stated above, we request Long-Term Confidentiality for exhibits which contain Block Diagram, Operational Description, Parts List/Tune Up Info, Schematics, SDR Software/Security Info. The above exhibits contain our benefit to our competitors. This information will not be publicly available. trade secrets and proprietary information that could be of If you have any questions, please feel free to contact us at the address shown below. Sincerely, Company Name:

Company Address:

Contact Name:

Signature:

Phone:

Fax:

E-mail:

Signature Date:

Document Version 1.1 2020-10-30