FCC ID: SY5KA4FGE07 Smart Key Fob

Document :

User Manual for TOKEN/TOKEN PLUS Fob Model :

SVI-KA4FGE07 Project Code :

Version:

1.0 Date:

Sep. 20. '19 Engineering change order-No.:

Design Freeze No.:

Number of pages:

6 Filename:

CASCO Identification No. :

Contents list System configulation Scope of SMART KEY SYSTEM Short description of the SYSTEM General Definition of SMART KEY 1. 1.1 1.2 1.2.1 1.2.2 Wireless Communication 1.2.3 1.3 1.4 2 Concept Description System Overview / Block Diagram Smart Key Fob button operation FCC/IC Compliance Statement Page 3 3 3 3 3 3 4 5 6 Editor :

KS.Kim Document name Project code Version:

1.0 Sep. 20. 2019 Identification No. : Document No. File:

Page 2 / 6 ECO / DF No. 1. System configulation 1.1 Scope of SMART KEY SYSTEM The System offers the following features:

passive access for two doors, driver side and passenger side as well as trunk/tailgate passive start after interior detection of the SMART KEY FOB (without interior trunk and hat shelf detection) LF-RF communication passive access trunk/tailgate via the trunk lid switch at the trunk max. 4 SMART KEY FOBs can be handled by the system communication to the engine management system via a single line interface communication to the ESCL via a single line interface 1.2 Short description of the SYSTEM 1.2.1 General Definition of SMART KEY The SMART KEY system is a system that allows the user to access and operate a vehicle in a very convenient way. To access the vehicle no traditional key or remote control unit is needed. The user carries a SMART KEY FOB which itself does not require any conscious actions by the user (e.g. operate a button). After being triggered the vehicle sends out a request in a limited range. If the SMART KEY FOB receives this request, it automatically sends a response to the vehicle. Then the system decides whether to perform a particular action (unlocking, locking) or remain inactive. 1.2.2 Wireless Communication Electromagnetic waves are used to exchange information between the vehicle and the SMART KEY FOB. Both, vehicle and SMART KEY FOB are equipped with a transmitter, a receiver and several antennas. 1.2.3 Concept Description With this concept it is possible to have a set of interior antennas that covers the vehicles interior and a set of exterior antennas that covers the vehicles exterior. For an unambiguous separation between the vehicles interior and exterior it is sufficient that at least one area is covered exactly by the corresponding operating ranges of the antennas. The functions of the SMART KEY system have to be provided in a clearly defined and limited range. For the up-link from the vehicle to the SMART KEY FOB, a magnetic field with a frequency of 125 kHz and ASK modulation is used. Inductive antennas in and at the vehicle radiate the electromagnetic energy. Editor :

KS.Kim Document name Project code Version:

1.0 Sep. 20. 2019 Identification No. : Document No. File:

Page 3 / 6 ECO / DF No. Technical aspects of 125 kHz magnetic field:

virtually no reflections, cubical decrease of field strength allows good range control, released frequency band (ISM), high penetration, low quiescent current demand due to 125 kHz input stage (SMART KEY FOB), less sensitive for detuning compared to higher frequency. For the down-link from the SMART KEY FOB to the vehicle, the standard radio frequency

(RF) is used (similar to the classic remote control functions) with FSK modulation. 1.3 System Overview / Block Diagram ECU sends LF challenge via exterior antenna ID tag sends identification code to RF receiver Doors are unlocked automatically User pulls open the door L F R F Figure 1: Principle of Communication Editor :

KS.Kim Document name Project code Version:

1.0 Sep. 20. 2019 Identification No. : Document No. File:

Page 4 / 6 ECO / DF No. 1.4 Smart Key Fob button operation Remote Start Door open/close (Left button)

; Drivers rear side door Door open/close (Right button)

; Passengers rear side door Lock Unlock Hold (Trunk) Panic You can lock, unlock, open trunk and so on your vehicle with this remote transmitter. Lock Unlock HOLD(Trunk) Remote Start

- When you push this button, all the doors will be locked.

- You can not lock any of the doors with this remote transmitter if any door is open or the key is in the fob holder.

- When you push this button, all the doors will be unlocked.

- You can not unlock any of the doors with this remote transmitter if any door is open or the key is in the fob holder.

- When you push this button and hold more than 1 second, the trunk will be opened.

- When you push and hold this button for about 3 second, vechicle will be started. Door open/close (Left button)

- When you push and hold this button for about 1 second,

- Drivers rear side door will be opened/closed. Door open/close (Right button)

- When you push and hold this button for about 1 second,

- Passengers rear side door will be opened/closed. Panic File:

- When you push this button for about 1 second, Horn will alarm. Editor :

KS.Kim Document name Project code Version:

1.0 Sep. 20. 2019 Identification No. : Document No. ECO / DF No. Page 5 / 6 2 FCC/IC Compliance Statement FCC Compliance Statement. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions :

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interferencethat may cause undesired operation. Do Not Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void users authority to operate the equipment. IC Compliance Statement. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) This device may not cause interference, and

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le present appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorisee aux deux conditions suivantes :

(1) lappareil ne doit pas produire de brouillage, et

(2) lutilisateur de lappareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible den compromettre le fonctionnement. Editor :

KS.Kim Document name Project code Version:

1.0 Sep. 20. 2019 Identification No. : Document No. File:

Page 6 / 6 ECO / DF No. FCC Information to User This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is con-nected. Consult the dealer or an experienced radio/TV technician for help. Caution Modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC ID: SY5KA4FGE07 FCC Compliance Information : This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. IC: 8325A-KA4FGE07

"Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device."

Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil nedoit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. Cet appareil et son antenne (s) ne doit pas tre co-localiss ou fonctionnant en conjonction avec une autre antenne ou transmetteur. It is the responsibility of the installer to ensure that when using the outdoor antenna kits, only those antennas certified with the product are used. The use of any antenna other than those certified with the product is expressly forbidden by FCC rules 47 CFR part 15.204 and IC RSS standards. Il est de la responsabilit de l'installateur de s'assurer que lorsque vous utilisez les kits d'antennes extrieures, seules les antennes certifis avec le produit sont utiliss. L'utilisation d'une antenne autre que ceux qui sont certifis avec le produit est expressment interdite par la rglementation FCC partie 47 CFR 15.204 et IC normes RSS.

FCC ID LABEL LOCATION 1. FCC ID label drawing SVI-KA4FGE07 FCC ID: SY5KA4FGE07 Made in Korea 2. FCC ID label location

775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: sales.eaw@us.bureauveritas.com Confidentiality Request Letter Revision History From Reason for Amendment (current / obsolete) Initial Release (obsolete) Adding CFR 2.459 (obsolete) Updated company template & Added text box Added IC confidentiality letter form (obsolete) Corrections to STC form. Added reference to KDB

(obsolete)

(obsolete) Updated company logo (current) 1.0 1.0 2.0 3.0 4.0 5.0 To 1.0 2.0 3.0 4.0 5.0 6.0 Approved Date Nov-14-2006 August 11 - 2008 Jan-31-2012 March-26-2015 Nov-19-2015 Jun-26-2019 SCS-F19: Confidentiality Request Letter Page 1 of 3 Rev 6.0 Continental Automotive Systems Corporation

(March 02, 2020) To:

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: SY5KA4FGE07 Pursuant to sections 0.457 and 0.459 of CFR 47, we respectfully request permanent confidential treatment of the following Exhibits accompanying this application as:

Block Diagram Schematics Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, ______________________________ Clients signature Clients name / title : Sung-Min Jang / Representative Contact information / address : 45-29, Saeum-ro, Icheon-si, Gyeonggi-do, 467-080, Korea Telephone: 82-31-645-4864 Fax No.: 82-31-637-0371 E-mail: Sungmin.Jang@continental-corporation.com SCS-F19: Confidentiality Request Letter Page 2 of 3 Rev 6.0 Continental Automotive Systems Corporation

(March 02, 2020) To: Federal Communications Commission Office of Engineering and Technology Equipment Authorization Division 7345 Oakland Mills Road Columbia, Maryland 21046 Subject: Short Term Confidentiality Request for FCC ID: SY5KA4FGE07 To Whom It May Concern:

Pursuant to sections 0.457 and 0.459 of CFR 47, and to avoid premature release of sensitive information prior to marketing or release of the product to the public, the applicant requests the following documents contained in this certification application be temporarily withheld from public disclosure for an initial period of 45 days; or for a specified date of not to exceed 180 days from the Grant Date. See KDB 726920. or 180

User Manual Internal Photos Test Setup photos External Photos The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Sincerely, ______________________________ Clients signature Clients name / title : Sung-Min Jang / Representative Contact information / address : 45-29, Saeum-ro, Icheon-si, Gyeonggi-do, 467-080, Korea Telephone: 82-31-645-4864 Fax No.: 82-31-637-0371 E-mail: Sungmin.Jang@continental-corporation.com SCS-F19: Confidentiality Request Letter Page 3 of 3 Rev 6.0

Tel: 408-526-1188 Fax: 408-526-1088 Email: sales.eaw@us.bureauveritas.com 775 Montague Expressway Milpitas, CA 95035 Project and Product Certification Representative Authorization Letter Reason for Amendment (current / obsolete) Initial Release (obsolete) Revised wording (obsolete) Updated company template (obsolete) Updated letter information (obsolete) Added FCC ID field (obsolete) Updated company name & logo (current) Revision History From 1.0 1.0 2.0 3.0 4.0 5.0 To 1.0 2.0 3.0 4.0 5.0 6.0 Approved Date Nov-14-2006 Sept25-2007 Jan-31-2012 May-23-2014 Sep-16-2014 Jun-27-2018 SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 6.0 Continental Automotive Systems Corporation

(March 02, 2020) To: BVCPS, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Product Certification Representative Authorization Letter We, _____ Continental Automotive Systems Corporation _____ hereby authorize Bureau Veritas Consumer Product Services, Inc. to act as a Certification Body for certifying for the following project(s):

FCC ID: SY5KA4FGE07 Product Description: Smart Key Fob Model: SVI-KA4FGE07 Sincerely, ______________________________ Clients signature Clients name / title : Sung-Min Jang / Representative Contact information / address : 45-29, Saeum-ro, Icheon-si, Gyeonggi-do, 467-080, Korea Telephone: 82-31-645-4864 Fax No.: 82-31-637-0371 E-mail: Sungmin.Jang@continental-corporation.com SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 6.0