The device under test is manufactured by the grantee (Continental Automotive Systems US Inc.);
and sold as an OEM product. Per 47 CFR 2.909, 2.927, 2.931, 2.1033, etc, the grantee must ensure the end-user has all applicable / appropriate operating instructions. When end-user instructions are required, as in the case of this product, the grantee must notify the OEM to notify the end-user. Continental Automotive Systems US Inc. will supply this document to the reseller/distributor dictating what must be included in the end users manual for the commercial product. INFORMATION TO BE INCLUDED IN THE END USERS MANUAL The following information (in blue) must be included in the end product users manual to ensure continued FCC regulatory compliance. The ID numbers must be included in the manual if the device label is not readily accessible to the end user. The compliance paragraphs below must be included in the user's manual.
******************************************************************************
USA FCC and ISED Canada Information This device complies with Part 15 of the FCC Rules and Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is Increase the separation between the equipment and receiver. connected. Consult the dealer or an experienced radio/TV technician for help. Grantee and OEM Integrators This device is intended for Grantee and OEM integrator use only. Please see the full grant of equipment document for restrictions. Label Information to the End User by the OEM Integrators If the FCC ID of this module is not visible when it is installed inside another device, then the outside of the device into which the module is installed must be label with:
Contains FCC ID: M3N-RCKFBLE and IC: 7812A-RCKFBLE. Antenna caution This radio transmitter IC: 7812A-RCKFBLE has been approved by Innovation, Science and Economic Development Canada to operate one with its integral trace antennas. The use of any other antenna is strictly prohibited for use with this device. FCC Radiation Exposure Statement This equipment complies with FCC and ISED radiation exposure limits set forth for an uncontrolled environment. This transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter. Co-location with other transmitter antennas would require the use of FCC multi-transmitter product procedures. Cet quipement est conforme aux limites d'exposition aux radiations de la FCC et de l'ISDE tablies pour un environnement non contrl. Ce module metteur ne doit pas tre co-localis ou fonctionner en conjonction avec une autre antenne ou un autre metteur. La co-localisation avec dautres antennes dmetteur ncessiterait lutilisation des procdures FCC relatives aux produits multi-metteurs. IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain chassis configurations or co-location with another transmitter), then the regulatory authorization may no longer be considered valid and the certification number could not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and potentially obtaining a separate authorization.