FCC ID: R33WA4200 802.11ac 4x4 Wave 2 Access Point

Regulatory Compliance & Safety Information for Control4 Model WA-4200, WA-4200-1, WA-

4200-C, WA-4200-C-1 Electrical Safety Advisory Scurit lectrique consultatif Important Safety Instructions Consignes de scurit importantes Read the safety instructions before using this product. Lisez les consignes de scurit avant d'utiliser ce produit. 1. Read these instructions. 1. Lisez ces instructions. 2. Keep these instructions. 2. Conservez ces instructions. 3. Heed all warnings. 3. Respectez tous les avertissements. 4. Follow all instructions. 4. Suivez toutes les instructions. 5. Do not use this apparatus near water. 5. Ne pas utiliser cet appareil prs de l'eau. 6. Clean only with dry cloth. 6. Nettoyez-le uniquement avec un chiffon sec. 7. Do not block any ventilation openings. Install in accordance with the manufacturers instructions. fabricant. 7. Ne pas bloquer les ouvertures de ventilation. Installer conformment aux instructions du 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 8. Ne pas installer prs de sources de chaleur telles que des radiateurs, registres de chaleur, poles, ou autres appareils (incluant les amplificateurs) qui produisent de la chaleur. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 9. Ne pas contourner le dispositif de scurit de la fiche polarise ou de mise la terre. Une fiche polarise possde deux lames dont une plus large que l'autre. Une fiche de terre a deux lames et une troisime broche de terre. La lame large ou la troisime broche est fournie pour votre scurit. Si la fiche fournie ne s'adapte pas votre prise, consultez un lectricien pour le remplacement de la prise obsolte. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 10. Protgez le cordon d'alimentation ne soit pitin ou pinc, en particulier au niveau des fiches, des prises et au point o il sort de l'appareil. 11. Only use attachments/accessories specified by the manufacturer. 11. Utilisez uniquement des fixations / accessoires spcifis par le fabricant. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 12. Utilisez uniquement avec le chariot, le socle, le trpied, le support ou la table spcifis par le fabricant ou vendu avec l'appareil. Lorsque vous utilisez un chariot, soyez prudent lorsque vous dplacez l'ensemble chariot / appareil pour viter des blessures dues au renversement. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 13. Dbranchez cet appareil pendant les orages ou lorsqu'il n'est pas utilis pendant de longues priodes de temps. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 14. Confiez toutes les rparations un personnel qualifi. Une rparation est ncessaire lorsque l'appareil a t endommag de quelque faon que ce soit le cordon d'alimentation ou la fiche est endommag, du liquide a t renvers ou si des objets sont tombs dans l'appareil, l'appareil a t expos la pluie ou l'humidit, ne fonctionne pas normalement, ou s'il est tomb. 15. This equipment uses AC power which can be subjected to electrical surges, typically lightning transients which are very destructive to customer terminal equipment connected to AC power sources. The warranty for this equipment does not cover damage caused by electrical surge or lightning transients. To reduce the risk of this equipment becoming damaged it is suggested that the customer consider installing a surge arrestor. 15. Cet quipement utilise la puissance AC qui peuvent tre soumis des surtensions lectriques, la foudre gnralement transitoires qui sont trs destructives envers les quipements terminaux connects des sources d'alimentation CA. La garantie de cet appareil ne couvre pas les dommages causs par les surtensions lectriques ou transitoires de foudre. Pour rduire le risque de cet quipement devient endommag, il est suggr que le client envisager l'installation d'un limiteur de surtension. 16. To completely disconnect unit power from the AC mains, remove the power cord from the appliance coupler and/or turn off the circuit breaker. To reconnect power, turn on the circuit breaker following all safety instructions and guidelines. The circuit breaker shall remain readily accessible. 16. Pour dbrancher compltement l'alimentation secteur du rseau secteur, retirez le cordon d'alimentation du coupleur de l'appareil et / ou teignez le disjoncteur. Pour reconnecter l'alimentation, allumez le disjoncteur en suivant toutes les consignes et consignes de scurit. Le disjoncteur doit tre facilement accessible. 17. This product relies on the buildings installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 20A. 17. Ce produit repose sur l'installation des btiments pour les courts-circuits (surintensit) de protection. Assurez-vous que le dispositif de protection est assigne ne dpassant pas:

20A. 18. CAUTION: As with all batteries, there is a risk of explosion or personal injury if the battery is replaced by an incorrect type. Dispose of used battery according to the instructions of the battery manufacturer and applicable environmental guidelines. Do not open, puncture or incinerate the battery, or expose it to conducting materials, moisture, liquid, fire or heat above 54 C or 130 F. 18. ATTENTION: Comme avec toutes les batteries, il ya un risque d'explosion ou de blessure si la batterie est remplace par un type incorrect. liminez les batteries usages selon les instructions du fabricant de la batterie et applicables des directives environnementales. Ne pas ouvrir, percer ou incinrer la batterie, ou de l'exposer des matriaux conducteurs, de l'humidit, du liquide, un incendie ou une temprature suprieure 54 C ou 130 F. 19. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. 19. N'introduisez jamais d'objets d'aucune sorte dans ce produit travers les fentes du botier car ils pourraient toucher des points de tension dangereux ou court-circuiter des pices qui pourraient entraner un incendie ou un choc lectrique. 20. This product can interfere with electrical equipment such as tape recorders, TV sets, radios, computers and microwave ovens if placed in close proximity. 20. Ce produit peut interfrer avec des appareils lectriques tels que les magntophones, tlviseurs, radios, ordinateurs et fours micro-ondes si placs proximit. The lightning flash and arrow head within the triangle is a warning sign alerting you of dangerous voltage inside the product L'clair et la flche dans le triangle est un signe d'alerte pour vous avertir d'une tension dangereuse l'intrieur du produit Caution: To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel. Attention: Pour rduire le risque de choc lectrique, ne pas retirer le couvercle

(ou l'arrire). Aucune pice rparable par l'utilisateur. Confiez l'entretien un personnel qualifi. The exclamation point within the triangle is a warning sign alerting you of important instructions accompanying the product. Le point d'exclamation dans un triangle est un signe d'avertissement vous signale des instructions importantes accompagnant le produit. See marking on bottom / back of product Voir le marquage sur les bas / dos du produit Warning!: To reduce the risk of electrical shock, do not expose this apparatus to rain or moisture AVERTISSEMENT! Pour rduire le risque de choc lectrique, n'exposez pas cet appareil la pluie ou l'humidit. Save these instructions Conservez ces instructions USA & Canada Compliance FCC Part 15, Subpart B & IC Unintentional Emissions Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver Increase the separation between the equipment and receiver. is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC rules and ISEDs licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la section 15 des rgles de la FCC et ISEDs aux RSS exempts de licence d'ISED. Son utilisation est soumise aux deux conditions suivantes: (1) Cet appareil ne doit pas causer dinterfrences nuisibles et (2) cet appareil doit accepter toutes les interfrences reues, y compris celles pouvant entraner un fonctionnement non souhait. IMPORTANT! Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. IMPORTANT! Tous les changements ou modifications pas expressment approuvs par la partie responsable de la conformit ont pu vider lautorit de lutilisateur pour actionner cet quipement. Canada Warning Statement:

CAN ICES-3 (B)/NMB-3(B) This product meets the applicable Innovation, Science and Economic Development Canada technical specifications. Ce produit rpond aux spcifications techniques applicables l'innovation, Science et Dveloppement conomique Canada. FCC Part 15, Subpart C / RSS-247 Intentional Emissions Interference Statement Compliance of this equipment is confirmed by the following certification numbers that are placed on the equipment:

Notice: The term FCC ID: and IC: before the certification number signifies that FCC and Industry Canada technical specifications were met. FCC ID: R33WA4200 IC: 7848A-WA4200 Operations in the 5.15-5.25GHz band are restricted to indoor usage only. Caution :

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

(ii) the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and

(iii) Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Avertissement:

(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;

(ii) le gain maximal d'antenne permis (pour les dispositifs utilisant la bande de 5725 5 850 MHz) doit tre conforme la limite de la p.i.r.e. spcifie pour l'exploitation point point et lexploitation non point point, selon le cas;

(iii) De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., quils ont la priorit) pour les bandes 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. FCC Partie 15, sous-partie C / RSS-247 Dclaration volontaire des missions interfrences Conformit de cet appareil est confirm par les chiffres de certification suivants qui sont placs sur l'quipement:

Avis: Le terme FCC ID:" et "IC:" devant le numro de certification signifie que les spcifications techniques de la FCC et d'Industrie Canada ont t respectes. FCC ID: R33WA4200 IC: 7848A-WA4200 Cet quipement doit tre install par des professionnels qualifis ou entrepreneurs conformment aux normes FCC partie 15.203 & IC RSS-247, Exigences d'antenne. Ne pas utiliser une antenne autre que celui fourni avec l'appareil. Cet metteur ne doit pas tre localis ou fonctionner avec d'autres antennes ou transmetteurs. Les oprations dans la bande 5.15-5.25GHz sont limites l'utilisation l'intrieur seulement. RF Radiation Exposure Statement This equipment complies with FCC RF and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body or nearby persons. Dclaration d'exposition aux radiations RF Cet quipement est conforme aux limites d'exposition aux rayonnements RF et IC de la FCC dfinies pour un environnement non contrl. Cet quipement doit tre install et utilis avec une distance minimale de 20 centimtres entre le radiateur et votre corps ou des personnes proches. Control4 Corporation 11734 S Election Road Draper, UT 84020 Email: rmidgley@control4.com Phone: (801) 523-3187 Europe Compliance Compliance of this equipment is confirmed by the following logo that is placed on the product ID label that is placed on the bottom of the equipment. The full text of the EU Declaration of Conformity (DoC) is available on the following pages:

This product can be put into service in all of the EU member states, European Free Trade Association

(EFTA) and EU candidate countries without any restriction. BE DE ES CY HU PL SK IS MK BG EE FR LV MT PT FI LI AL CZ IE HR LT NL RO SE NO RS DK EL IT LU AT SI UK CH TR The frequency and maximum transmitted power in EU are listed as below:

2412 - 2472 MHz: 17.15 dBm 5470 - 5725 MHz: 23.62 dBm WLAN 5GHz:

Operations in the 5.15-5.35GHz band are restricted to indoor usage only. Recycling Control4 understands that a commitment to the environment is essential for a health life and sustainable growth for future generations. We are committed to supporting the environmental standards, laws, and directives that have been put in place by various communities and countries that deal with concerns for the environment. This commitment is represented by combining technological innovation with sound environmental business decisions. WEEE Compliance Control4 is committed to meeting all requirements of the Waste Electrical and Electronic Equipment (WEEE) directive (2012/19/EC). The WEEE directive requires the manufacturers of electrical and electronic equipment who sell in EU countries: (1) label their equipment to notify customers that it needs to be recycled, and (2) provide a way for their products to be appropriately disposed of or recycled at the end of their product lifespan. For collection or recycling of Control4 products, please contact your local Control4 representative or dealer. About this Document Copyright 2018 Control4 Corporation. All rights reserved. Control4 and the Control4 logo are registered trademarks or trademarks of Control4 Corporation in the United States and/or other countries. Part Number 200-00XXX Rev A, 1/2/2019 European Compliance (English) Conformity of the equipment with the guidelines below is attested by the application of the CE mark. Manufacturers Name:

Manufacturers Address:

CE Declaration of Conformity CONTROL4 CORPORATION 11734 S. ELECTION ROAD SUITE 200 SALT LAKE CITY UT 84020 USA EU Representative Name: CONTROL4 EMEA LIMITED EU Representative Address: UNIT3, GREEN PARK BUSINESS CENTRE SULTON-ON-THE FOREST YORK YO61 IET, UNITED KINGDOM 802.11ac 4x4 Wave 2 Access Point Pakedge WA-4200-1, WA-4200-C-1 Product Name(s):

Brand:

Model(s):

Product Standard(s) to which Conformity of the Council Directive(s) is declared:

EMC - 2014/30/EU Electromagnetic Compatibility (EMC) Directive:

(Emissions) EN 55032:2015 (Immunity) EN 55035:2017, EN 61000-3-2:2014 & EN 61000-3-

3:2013 Safety 2014/35/EU Low Voltage Directive (LVD):

EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013 Radio - 2014/53/EU Radio Equipment Directive (RED):

EN 300 328 V2.1.1 (2016-11), EN 301 893 V2.1.1 (2017-05), EN 301 489-1 v2.2.1 (2019-03), EN 301 489-17 V3.2.0 (2017-03) & EN 62311:2008 RoHS - 2011/65/EU Restriction of the Use of certain Hazardous Substances in Electrical and Electronic Equipment (EEE) & WEEE - 2002/96/EC Waste of Electrical and Electronic Equipment (EEE). We, the undersigned, hereby declare that the equipment specified above conforms to the above directives and standards. Date of Issue: TBD Legal Representative Signature Roger Midgley Sr. Regulatory Compliance Engineer Conformit europenne (French) Conformit de l'quipement avec les directives ci-dessous est atteste par l'apposition de la marque CE. Dclaration de conformit CE Le nom du fabricant:

Le fabricant Adresse:

Nom Reprsentant de l'UE: CONTROL4 EMEA LIMITED UE reprsentant Adresse: Unit3, GREEN PARK CENTRE D'AFFAIRES CONTROL4 CORPORATION 11734 S. LECTION Road Suite 200 SALT LAKE CITY UT 84020 USA Sulton-ON-THE FOREST YORK YO61 IET, ROYAUME-UNI 802.11ac 4x4 Wave 2 Access Point Pakedge WA-4200-1, WA-4200-C-1 Nom (s) de produit:

Marque:

Modle (s):

Produit standard (s) dont la conformit de la directive du Conseil (s) est dclare:

EMC - 2014/30 / "compatibilit lectromagntique (CEM)" UE:

(missions) EN 55032:2015 (immunit) EN 55035:2017, EN 61000-3-2:2014 & EN 61000-3-

3:2013 Scurit - 2014/35/EU "Directive Basse Tension (DBT)":

EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013 Radio - 2014/53 / UE directive quipement radio (RED):

EN 300 328 V2.1.1 (2016-11), EN 301 893 V2.1.1 (2017-05), EN 301 489-1 v2.2.1 (2019-03), EN 301 489-17 V3.2.0 (2017-03) & EN 62311:2008 RoHS - 2011/65 / UE limitation de l'utilisation de certaines substances dangereuses dans les quipements lectriques et lectroniques (EEE) et DEEE - 2002/96 / CE Dchets d'quipements lectriques et lectroniques (EEE). Nous, soussigns, dclarons que l'quipement indiqu ci-dessus est conforme aux directives et normes ci-dessus. Date de publication TBD Reprsentant lgal Signature Roger Midgley Ingnieur de conformit rglementaire Sr. European Compliance (German) Die Konformitt mit den folgenden Richtlinien wird durch die Anwendung des CE-Kennzeichen besttigt. CE-Konformittserklrung 802.11ac 4x4 Wave 2 Access Point Pakedge WA-4200-1, WA-4200-C-1 Control4 CORPORATION 11734 S. WAHL ROAD SUITE 200 SALT LAKE CITY UT 84020 USA Control4 EMEA LIMITED Unit3, GREEN Park Geschftszentrum Sulton-ON-THE FOREST YORK YO61 IET, VEREINIGTES KNIGREICH Name des Herstellers:

Adresse des Herstellers:

EU-Vertreter Name:

EU-Vertreter Adresse:

Produkt-Name (n):

Marke:

Modell (e):

Produkt-Norm (en), um die Konformitt der Richtlinie (n) deklariert ist:

EMC - 2014/30 / EG "Elektromagnetische Vertrglichkeit (EMV) Die Richtlinie":

(Emissionen) EN 55032:2015 (Immunitt) EN 55035:2017, EN 61000-3-2:2014 & EN 61000-3-

3:2013 Sicherheit - 2014/35/EU "Niederspannungsrichtlinie (LVD)":

EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013 Radio - 2014/53 / EU ber Funkanlagen-Richtlinie (RED):

EN 300 328 V2.1.1 (2016-11), EN 301 893 V2.1.1 (2017-05), EN 301 489-1 v2.2.1 (2019-03), EN 301 489-17 V3.2.0 (2017-03) & EN 62311:2008 RoHS - 2011/65 / EU zur Beschrnkung der Verwendung bestimmter gefhrlicher Stoffe in Elektro- und Elektronikgerten (EEE) & WEEE - 2002/96 / EG Richtlinie ber Elektro- und Elektronikgerten (EEE). Wir, die Unterzeichneten, erklren hiermit, dass das oben angegebene Gert zu den oben genannten Richtlinien und Normen. Ausstellungsdatum: TBD Gesetzlicher Vertreter Stempel, Unterschrift Roger Midgley Sr. Regulatory Compliance-Ingenieur Conformit Europea (Italian) Conformit del materiale con le linee guida qui sotto attestata dall'applicazione del marchio CE. Dichiarazione di conformit CE Sulton-ON-THE FOREST YORK YO61 IET, REGNO UNITO 802.11ac 4x4 Wave 2 Access Point Pakedge WA-4200-1, WA-4200-C-1 Control4 CORPORATION 11734 S. ELEZIONI STRADA SUITE 200 SALT LAKE CITY UT 84020 Stati Uniti d'America Nome del produttore:

Indirizzo del produttore:

UE Nome Rappresentante: Control4 EMEA LIMITED UE Indirizzo Rappresentante: Unit3, GREEN PARK BUSINESS CENTRE Nome del prodotto (s):

Marca:

Modello (s):

Prodotto standard (s) a cui conformit della direttiva del Consiglio (s) dichiarato:

EMC - 2014/30 / UE "Compatibilit elettromagnetica (EMC)":

(Emissioni) EN 55032:2015 (immunit) EN 55035:2017, EN 301 489-1 v2.2.1 (2019-03), EN 301 489-17 V3.2.0 (2017-03), EN 61000-3-2 : 2014 e EN 61000-3-3: 2013 Sicurezza - 2014/35/EU "Direttiva bassa tensione (LVD)":

EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013 Radio - 2014/53 / Direttiva sulle apparecchiature radio dell'UE (RED):

EN 300 328 V2.1.1 (2016-11), EN 301 893 V2.1.1 (2017-05), EN 301 489-1 v2.2.1 (2019-03), EN 301 489-17 V3.2.0 (2017-03) & EN 62311:2008 RoHS - 2011/65 Limitazione / UE dell'uso di determinate sostanze pericolose nelle apparecchiature elettriche ed elettroniche (AEE) e RAEE - 2002/96 / CE sui rifiuti di apparecchiature elettriche ed elettroniche (AEE). I sottoscritti, dichiariamo che l'apparecchiatura specificata in precedenza conforme alle direttive e norme di cui sopra. Data di pubblicazione: TBD Rappresentante legale Firma Roger Midgley Suor Conformit alle normative Ingegnere Conformidad Europea (Spanish) La conformidad de los equipos con las siguientes pautas es atestiguado por la aplicacin de la marca CE. Declaracin de conformidad CE Control4 EMEA LIMITED Sulton-EN-EL BOSQUE YORK YO61 IET, REINO UNIDO 802.11ac 4x4 Wave 2 Access Point Pakedge WA-4200-1, WA-4200-C-1 Control4 CORPORACIN 11734 S. ELECCIN Road Suite 200 SALT LAKE CITY UT 84020 EE.UU. Nombre del fabricante:

Direccin del fabricante:

UE Nombre Representante:

Direccin Representante de la UE: Tema 3., VERDE PARQUE EMPRESARIAL CENTRO Nombre (s) del producto:

Marca:

Modelo (s):

Producto estndar (s) a la que la conformidad de la Directiva del Consejo (s) se declara:

EMC - 2014/30 / UE "Directiva de compatibilidad electromagntica (EMC)":

(Emisiones) EN 55032:2015 (inmunidad) EN 55035:2017, EN 301 489-1 v2.2.1 (2019-03), EN 301 489-17 V3.2.0 (2017-03), EN 61000-3-2 : 2014 e EN 61000-3-3: 2013 Seguridad - 2014/35/EU "Directiva de Baja Tensin (LVD)":

EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013 Radio - 2014/53 / Directiva de Equipos de Radio de la UE (RED):

EN 300 328 V2.1.1 (2016-11), EN 301 893 V2.1.1 (2017-05), EN 301 489-1 v2.2.1 (2019-03), EN 301 489-17 V3.2.0 (2017-03) & EN 62311:2008 RoHS - 2011/65 restriccin del uso de ciertas sustancias peligrosas en equipos electrnicos (AEE) y WEEE elctricos y / UE - 2002/96 / CE de Residuos de Aparatos Elctricos (AEE) y electrnicos. Nosotros, los abajo firmantes, declaramos por la presente que el equipo anteriormente mencionado se ajusta a las directrices y estndares anteriores. Fecha de emisin: TBD Representante legal Firma Roger Midgley Ingeniero Sr. Cumplimiento de la normativa Conformidade Europeia (Portuguese) Conformidade do equipamento com as diretrizes abaixo atestada pela aplicao da marca CE. Declarao de Conformidade CE Control4 EMEA LIMITED Sulton-ON-THE FOREST YO61 IET YORK, REINO UNIDO 802.11ac 4x4 Wave 2 Access Point Pakedge WA-4200-1, WA-4200-C-1 Control4 CORPORATION 11734 S. ELEIO ROAD SUITE 200 SALT LAKE CITY UT 84020 EUA Nome do fabricante:

Do fabricante Endereo:

Representante da UE Nome:

Representante da UE Endereo: UNIT3, GREEN PARK CENTRO DE NEGCIO Nome (s) produto:

Marca:

Modelo (s):

Padro do produto (s) a que Conformidade da Directiva do Conselho (s) declarado:

EMC - 2014/30 / UE "Compatibilidade Electromagntica (EMC)":

(Emisses) EN 55032:2015 (Imunidade) EN 55035:2017, EN 301 489-1 v2.2.1 (2019-03), EN 301 489-17 V3.2.0 (2017-03), EN 61000-3-2 : 2014 e EN 61000-3-3: 2013 Segurana - 2014/35/EU "Directiva de Baixa Tenso (LVD)":

EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013 Rdio - 2014/53 / UE Directiva equipamento de rdio (RED):

EN 300 328 V2.1.1 (2016-11), EN 301 893 V2.1.1 (2017-05), EN 301 489-1 v2.2.1 (2019-03), EN 301 489-17 V3.2.0 (2017-03) & EN 62311:2008 RoHS - 2011/65 / UE Restrio do Uso de Certas Substncias Perigosas em Equipamentos Elctricos e Electrnicos (EEE) e WEEE - 2002/96 / EC de Resduos de Equipamentos Elctricos e Electrnicos (EEE). Ns, abaixo-assinado, declaro que o equipamento especificado acima est em conformidade com as diretrizes e normas acima referidas. Data de Emisso: TBD Representante legal Assinatura Roger Midgley Sr. Engenheiro Conformidade Regulatria

WA-4200, WA-4200-1 802.11ac 4x4 Wave 2 Access Point BakPak Lite QUICK START GUIDE WA-4200 features 802.11ac dual-band 44 wireless technology Advanced Wave 2 wireless technology with MU-MIMO and beamforming Powered by PoE+ (or optional 12VDC 2A power adapter, sold separately) Single-AP to multi-AP cloud configuration with built-in BakPak Lite 2 Gigabit Ethernet ports For information on using the AP, go to pkdge.co/wa4200-ug. System requirements Windows or Mac PC with an Ethernet port and Google Chrome or Mozilla Firefox Specifications and credentials Operation mode: Access Point IP address: If no DHCP server is detected, the default IP address is automatically set to 192.168.1.21. Username/Password (default): admin/password SSIDs (default): Pakedge_Main (5 GHz), Pakedge_Alt (2.4 GHz), security/password: WPA2-PSK/pakedgewireless Guest SSIDs (default): PakedgeGuest_Main and PakedgeGuest_Alt, security/password: WPA2/pakedgeguest Factory default transmit power: 13dBm for 2.4GHz and 18 dBm for 5 GHz. Power: PoE+ or AC adapter (not included) 12VDC 2A 22 Mounting on a ceiling 1 Tape the included template against the desired mounting location, then mark the places to drill mounting holes and install the appropriate mounting hardware. 2 Slide the tabs in the AP into the slots on the bracket, then slide until its locked. 1 33 2 Removing the AP from the bracket To remove the AP from the bracket:

1 While pressing the AP against the bracket, slide the AP up slightly, then pull it away from the bracket. 1 Powering up The AP can be powered by either PoE or the optional AC power adapter (sold separately). To power up the access point:

1 Connect power using a POE injector or POE switch, or with the optional AC power adapter (sold separately). The access point should now be up and running with its default settings. It does not need to be configured to be functional. To make changes to the SSID and security settings, you need to access the AP using a web browser. 2 44 Logging in to the access point To log in to the access point:

1 Connect the access point to your PoE switch with an Ethernet cable. 2 Log in to your Pakedge router to find the IP address assigned to the access point under the DHCP Client Table. Tip: If you do not have a router in your network that distributes IP addresses, you can try to access the access point through its default IP address of 192.168.1.21. 3 Enter that IP address into a web browser to open the access point interface. The Sign In page opens. Note: Because the AP uses self-signed certificates for secure connection to the web browser, a security message will appear. There is no risk in proceeding to the APs web interface, and communications will remain secure. 4 In the username box, type admin. In the password box, type password, then click Sign In. The first time you log in, the Configure page opens. 55 5 Enter and verify a new username and password (required) before continuing, then click Apply to complete the setup. Caution: For international models, you must change the Country Code (a drop-down list defaulting to GB - United Kingdom), to the specific country of operation. Note: Refer to the user guide (pkdge.co/wa4200-ug) for detailed configuration information. 66 Registering your device with BakPak Lite You can connect your access point to your existing BakPak account or create a new account to manage all of your BakPak network management agents. To register your device to your BakPak account:

1 In the devices Connections tab, to the right of the This product is not managed by BakPak message, click Click here to enroll. 2 Follow the on-screen instructions to complete your device registration. 77 Creating a BakPak site for WA Series APs To begin managing and configuring the AP, you need to create a BakPak site for it. To create a BakPak site:

1 Log in to your BakPak account, then click Add Site to create a site. 2 In the Management Agent list, select the first WA-4200, complete the site information, then click OK. 88 Adding WA Series APs to the site After the BakPak site is created, the WA-4200 will act as the master AP for adding more WA-4200 Series APs to the site. For the full multi-AP deployment guide, seepkdge.co/wa4200-multi. To add APs and provision them with the existing configuration:

1 Make sure that the master AP is already configured (through the local UI or BakPak), and that the additional APs are turned on for at least five minutes and connected to your network. 2 In BakPak, select the new WA-4200 site, then click Device Discovery. Any additional WA-4200 Series APs are discovered and appear as tiles that can be selected (already selected by default). 99 3 Click OK. The APs are added to the site. 4 To apply the master APs settings to the new APs, in the BakPak site select the master AP, then complete the site information and click Save & Apply Multiple at the bottom. The settings are copied to the new APs. 1010 1111 Technical Support For technical help:

www.pakedge.com support@pakedge.com

(650) 385-8703 For regulatory information:

www.pakedge.com/regulatory 11734 S. Election Road Draper, UT 84020 Main: (650) 385-8700 Fax: (650) 685-5520 www.pakedge.com sales@pakedge.com 2019 Control4. All rights reserved. Latest version at pkdge.co/wa4200-qsg 200-00636-A 2019-07-29 MS

WA-4200-C, WA-4200-C-1 802.11ac 4x4 Wave 2 Access Point, In-Ceiling BakPak Lite QUICK START GUIDE WA-4200-C features 802.11ac dual-band 44 wireless technology Advanced Wave 2 wireless technology with MU-MIMO and beamforming Powered by PoE+ (or optional 12VDC 2A power adapter, sold separately) Single-AP to multi-AP cloud configuration with built-in BakPak Lite 2 gigabit Ethernet ports For information on using the AP, go to pkdge.co/wa4200-ug. System requirements Windows or Mac PC with an Ethernet port and Google Chrome or Mozilla Firefox Specifications and credentials Operation mode: Access Point IP address: If no DHCP server is detected, the default IP address is automatically set to 192.168.1.21. Username/Password (default): admin/password SSIDs (default): Pakedge_Main (5 GHz), Pakedge_Alt (2.4 GHz), security/password: WPA2-PSK/pakedgewireless Guest SSIDs (default): PakedgeGuest_Main and PakedgeGuest_Alt, security/password: WPA2/pakedgeguest Factory default transmit power: 13dBm for 2.4GHz and 18 dBm for 5 GHz. Power: PoE+ or AC adapter (not included) 12V DC 2A 22 Planning the wireless network For tips on planning your network and positioning the access points, see:

Wireless Design Guide at pkdge.co/wirelessdesign Best Practices for Access Point Placement Guide at pkdge.co/ap-bp Wireless Design Guide AP Placement Guide Mounting into the in-ceiling bracket 1 Place the included template against the ceiling at the desired location, then cut along the dotted line with a drywall saw. 33 2 Make sure that the in-ceiling brackets mounting latches are in their closed position. 3 Insert the in-ceiling bracket into the opening you created in step 1. 44 4 Tighten both mounting latch screws clockwise until the ceiling is securely clamped between the in-ceiling bracket and the latches. 5 Press the four tabs on the swing-out bracket rails with the corresponding holes in the bottom of the AP, then slide the AP slightly away from the bracket to lock the tabs into the holes. 6 Press the AP into the bracket until it clicks into place. 55 Powering up The AP can be powered by either PoE or the optional AC power adapter (sold separately). To power up the access point:

1 Connect power using a POE injector or POE switch, or with the optional AC power adapter (sold separately). The access point should now be up and running with its default settings. It does not need to be configured to be functional. To make changes to the SSID and security settings, you need to access the AP using a web browser. 66 Logging in to the access point To log in to the access point:

1 Connect the access point to your PoE switch with an Ethernet cable. 2 Log in to your Pakedge router to find the IP address assigned to the access point under the DHCP Client Table. Tip: If you do not have a router in your network that distributes IP addresses, you can try to access the access point through its default IP address of 192.168.1.21. 3 Enter that IP address into a web browser to open the access point interface. The Sign In page opens. Note: Because the AP uses self-signed certificates for secure connection to the web browser, a security message will appear. There is no risk in proceeding to the APs web interface, and communications will remain secure. 4 In the username box, type admin. In the password box, type password, then click Sign In. The first time you log in, the Configure page opens. 77 5 Enter and verify a new username and password (required) before continuing, then click Apply to complete the setup. Caution: For international models, you must change the Country Code (a drop-down list defaulting to GB - United Kingdom), to the specific country of operation. Registering your device with BakPak Lite You can connect your access point to your existing BakPak account or create a new account to manage all of your BakPak network management agents. To register your device to your BakPak account:

1 In the devices Connections tab, to the right of the This product is not managed by BakPak message, click Click here to enroll. 88 2 Follow the on-screen instructions to complete your device registration. Creating a BakPak site for WA Series APs To begin managing and configuring the AP, you need to create a BakPak site for it. To create a BakPak site:

1 Log in to your BakPak account, then click Add Site to create a site. 2 In the Management Agent list, select the first WA-4200, complete the site information, then click OK. 99 Adding WA Series APs to the site After the BakPak site is created, the AP will act as the master AP for adding more WA-4200 APs to the site. For the full multi-AP deployment guide, seepkdge.co/wa4200-multi. To add APs and provision them with the existing configuration:

1 Make sure that the master AP is already configured (through the local UI or BakPak), and that the additional APs are turned on for at least five minutes and connected to your network. 2 In BakPak, select the new WA-4200 site, then click Device Discovery. Any additional WA Series APs are discovered and appear as tiles that can be selected (already selected by default). 1010 3 Click OK. The APs are added to the site. 4 To apply the master APs settings to the new APs, in the BakPak site select the master AP, then complete the site information and click Save & Apply Multiple at the bottom. The settings are copied to the new APs. 1111 Technical Support For technical help:

www.pakedge.com/portal support@pakedge.com

(650) 385-8703 For regulatory information:

www.pakedge.com/regulatory 11734 S. Election Road Draper, UT 84020 Main: (650) 385-8700 Fax: (650) 685-5520 www.pakedge.com sales@pakedge.com 2019 Control4. All rights reserved. Latest version at pkdge.co/wa4200c-qsg 200-00646-A 2019-10-04 MS

4-0.5R 33.5 90.5 802.11ac 4x4 Wave 2 Access Point This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. PROTOTYPE NOT FOR RESALE MODEL/MODLE/: WA-4200 DEFAULT IP ADDRESS: DHCP or 192.168.1.21 DEFAULT LOGIN: admin/password FCC ID:R33WA4200 INPUT:12V ,2A Made in Taiwan Fabriqu en Taiwan www.pakedge.com 210-01799 S P E C I F I C A T I O N Die cut line

- Dimension : 90.5*33.5 mm

- Printed Color : PANTOME 426C

- Tolerance : 0.1 mm

- Material : 25(UL certified)+ (MZS215)+

Code : HTLSMI25 Adhesive : Releasr force (24 hr) : 7.0 gf/25mm Service Temperature: -20~+120 Coating : Peel Adhesion: 0.6 kgf / 25mm Service Temperature: 110 6710A6153190 2019/07/01 Fabi

- data

- 0.2mm

- 0.2

NO. 1.0 1.1 REVISIONS PROTOTYPE RELEASE REMOVED IC ID FROM LABEL DATE 05/21/19 09/16/19 BY SP SP 4-1R 91 802.11ac 4x4 Wave 2 Access Point, In-Ceiling This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. 34 PROTOTYPE NOT FOR RESALE MODLE : WA-4200-C MODEL/ /

DEFAULT IP ADDRESS: DHCP or 192.168.1.21 DEFAULT LOGIN: admin/password FCC ID:R33WA4200 INPUT:12V ,2A Made in Taiwan Fabriqu en Taiwan www.pakedge.com 210-01800 NOTES (UNLESS OTHERWISE SPECIFIED):

1. MATERIAL:

COLOR: WHITE SEE PART NUMBER 211-00023 FOR MATERIAL SPECIFICATION AND APPROVED MANUFACTURERS 2. PRINTING:

PRINT COLOR: PANTONE 279 C (Blue) USE SHEET 2 FOR LABEL PLACEMENT REFERENCE PDF DOCUMENT IS FOR REFERENCE ONLY 3. DOCUMENT SCHEDULE:

SHEET 1: ARTWORK SHEET 2: LABEL PLACEMENT TOLERANCES:

(ALL DIMENSIONS ARE IN MM) DECIMAL: 0.508 2 DECIMAL: 0.254 3 DECIMAL: 0.127 RAD/CHAM: 0.508 ANGLE: 1.00 THE INFORMATION CONTAINED IN THIS DRAWING AND THE ASSOCIATED CAD DATA IS CONFIDENTIAL, AND IS THE SOLE PROPERTY OF CONTROL4. ANY USE, REPRODUCTION, OR DISCLOSURE - IN WHOLE OR IN PART - WITHOUT WRITTEN PERMISSION FROM CONTROL4 IS PROHIBITED COPYRIGHT 2019 11734 S. Election Road, Suite 200 Draper, UT 84020 Phone: 801-523-3100 Fax: 801-523-3199 TITLE LABEL, PRODUCT ID W/REG LOGOS SIZE PART #

A SCALE 1:1 WA-4200-C 210-01800 DO NOT SCALE REV 1.1 SHEET 1 OF 2 802.11ac 4x4 Wave 2 Access Point, In-Ceiling This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. PROTOTYPE NOT FOR RESALE MODLE MODEL/ /: WA-4200-C DEFAULT IP ADDRESS: DHCP or 192.168.1.21 DEFAULT LOGIN: admin/password FCC ID:R33WA4200-C INPUT:12V ,2A Made in Taiwan Fabriqu en Taiwan www.pakedge.com 210-01800 TITLE COPYRIGHT 2019 11734 S. Election Road, Suite 200 Draper, UT 84020 Phone: 801-523-3100 Fax: 801-523-3199 LABEL, PRODUCT ID W/REG LOGOS A SIZE PART #

1.1 FOR REFERENCE ONLY NOT TO SCALE SHEET 2 OF 2 REV WA-4200-C 210-01800

Date: September 17, 2019 DTS-UNII Device Declaration Letter To whom it may concern:

We have declared below featured for FCC equipment authorization, Device FCC ID: R33WA4200

(1) DFS Device -- Master , Client with Radar detection capability , Client without radar detection capability, N/A

(2) Active / Passive Scanning, adhoc mode access point capability Frequency Band Active Scanning passive scanning Ad Hoc Mode or

(MHz)

(the device can transmit

(where the device is can a probe (beacon)) listen only with no Yes , Yes , Yes , No No No probes) Yes , No Yes , No Yes , No WIFI Direct capability Yes , No Yes , No Yes , No Access point capability Yes , Yes , Yes , No No No 5250~5350 5470~5600 5650~5725

(3) Country code selection ability -

Yes , No If yes, pls explain how it was implemented : (pls also help to provide detail of options for each country selection)

(4) Meet 15.202 requirement - Yes , No , pls check below :

A master device is defined as a device operating in a mode in which it has the capability to transmit without receiving an enabling signal. In this mode it is able to select a channel and initiate a network by sending enabling signals to other devices A client device is defined as a device operating in a mode in which the transmissions of the device are under control of the master. A device in client mode is not able to initiate a network. For client devices that have software configuration control to operate in different modes (active scanning in some and

(5) passive scanning in others) in different bands (devices with multiple equipment classes or those that operate on non-DFS frequencies) or modular devices which configure the modes of operations through software, the application must provide software and operations description on how the software and / or hardware is implemented to ensure that proper operations modes can not be modified by end user or an installer. Apply , No Apply , (If apply , pls help to provide explanation on it was implement , and how software was controlled) Name / Title : Roger J Midgley / Sr. Regulatory Compliance Engineer Signature :

Phone : 801 523 3100 #3187 Fax : 801 523 3199 Email : rmidgley@control4.com Address: 11734 S. Election Road, Draper, Utah, 84020, United States 11734 South Election Road | Draper, Utah 84020 | www.control4.com | 801.523.3100 phone | 801.523.3199 fax

WIFI Channel 12 & 13 Declaration Letter To whom it may concern :

We have declared below featured for FCC equipment authorization in regard to 802.11b/g/n channel 12 & 13 operating capability for FCC ID:R33WA4200 Please check Product hardware does not have the capability to operate on channel 12 & 13 Product hardware has the capability to operate on channel 12 & 13. However, these 2 channels will be disabled via software and user will not able to enable these 2 channels Product hardware has the capability to operate on channel 12 & 13. And meeting KDB 594280 D01 requirement. Pls explain detail here. _________________ Others Pls explain detail here. Company Name: Control4 Corporation Address : 11734 S. Election Road, Draper, UT, 84020, United States

Roger Midgley Sr. Regulatory Compliance Engineer Telephone Number: 801-523-3187 Fax Number: 801-523-3199 E-mail Address: rmidgley@control4.com 11734 South Election Road | Draper, Utah 84020 | www.control4.com | 801.523.3100 phone | 801.523.3199 fax

September 17, 2019 Dear Sir or Madam, SUBJECT: End Product Model Difference Attestation FCC ID:R33WA4200 IC: 7848A-WA4200 Models: WA-4200, WA-4200-C, WA-4200-1 & WA-4200-C-1 We, Control4 Corporation, hereby declare that our end product, 802.11ac 4x4 Wave 2 Access Point, includes 4 model names as listed above. The above listed models are electrically and mechanically identical. The intention of these models is only for marketing purpose. The difference between each model is listed below:

WA-4200 WA-4200-C WA-4200-1 WA-4200-C-1 USA version only. USA version only with ceiling mounting bracket. International version (software to select the region where the access point is installed). International version (software to select the region where the access point is installed), with ceiling mounting bracket. Should you have any question, feel free to contact me directly. Sincerely yours,

Roger Midgley Sr. Regulatory Compliance Engineer Telephone Number: 801-523-3187 Fax Number: 801-523-3199 E-mail Address: rmidgley@control4.com 11734 South Election Road | Draper, Utah 84020 | www.control4.com | 801.523.3100 phone | 801.523.3199 fax

775 Montague Expressway Milpitas, CA 95035 Tel:

Fax:

Email:

408-526-1188 408-526-1088 TCB@siemic.com Project and Product Certification Representative Authorization Letter Reason for Amendment (current / obsolete) Revision History To From Initial Release (obsolete) Revised wording (obsolete) Updated company template (obsolete) Updated letter information (obsolete) Added FCC ID field (current) Updated company name & logo (current) 1.0 1.0 2.0 3.0 4.0 5.0 1.0 2.0 3.0 4.0 5.0 6.0 Approved Date Nov-14-2006 Sept25-2007 Jan-31-2012 May-23-2014 Sept 16 2014 Jun-27-2018 SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 6.0 Control4 11734 S. Election Road, Draper, Utah, 84020, United States Date: September 17, 2019 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Product Certification Representative Authorization Letter We, Control4 hereby authorize SIEMIC, Inc. to act as a Certification Body for certifying for the following project(s):

Product description: 802.11ac 4x4 Wave 2 Access Point Model name: WA-4200, WA-4200-1, WA-4200-C, WA-4200-C-1 FCC ID: R33WA4200 Sincerely, Signature:

Name / Title: Roger J Midgley/ Sr. Regulatory Compliance Engineer Contact information / address: 11734 S. Election Road, Draper, Utah, 84020, United States SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 6.0