7" T3 Series Tabletop Touch Screen Installation Guide Supported models C4-TT7-xx 7" Tabletop Touch Screen (black or white) Introduction The Control4 T3 Series 7" Tabletop Touch Screens offer complete system control in an elegant, compact, and portable design. The touch screens are equipped with a full capacitive screen, audio and video Intercom (with the built-in camera) using SIP, and more. This touch screen can be located anywhere, and the convenient recharging station enables it to be used as either a tabletop or portable interface. Choose from four installation options:
Option 1: PoE data and power. Ethernet network connection and power are provided through a PoE injector. No additional wiring is needed. Option 2: Ethernet data and AC power. Ethernet network connection is provided through an Ethernet cable, and power is provided through the ACpower adapter. Option 3: WiFi data and AC power. WiFi is used as the network connection, and power is provided through the ACpower adapter. Option 4: WiFi data and PoE power. WiFi is used as the network connection, and power is provided through a PoE injector. Note: 802.11b is not recommended for Video Intercom. We recommend using Wireless-N. See Specifications and Power and Network Installation Options for more information. Box contents 7" Tabletop Touch Screen Recharging station Warranty card Ferrite bead Accessories available for purchase Control4 PoE Injector, sold separately (AC-POE1-B). Warnings Warning! This product must be grounded in accordance with the National Electrical Code (NEC) requirements. Avertissement ! Ce produit doit tre fondu selon les conditions lectriques nationales de code (NEC). Caution! Do not place the touch screen near sources of heat or expose to direct sunlight for an extended time. Avertissement ! Ne placez pas lunit prs des sources de chaleur ou exposition pour diriger la lumire du soleil pendant une priode prolonge. Caution! This product generates heat. The room must have adequate ventilation or the ability to dissipate heat effectively. Avertissement ! Ce produit produit de la chaleur. La salle doit avoir ventilation proportionne ou la capacit dabsorber la chaleur efficacement. Caution! Use this product only in dry locations. Avertissement ! Employez ce produit seulement dans des endroits secs. Caution! This product is for residential use only. Avertissement ! Ce produit est pour lusage rsidentiel ou commercial seulement. Caution! Do not use pens or sharp objects to navigate or make selections on the touch screen. To select an item or scroll through a list, use your fingertip. Avertissement ! Nemployez pas les stylos ou les objets pointus pour diriger ou pour faire des choix sur lcran. Pour choisir un article ou un rouleau par une liste, employez votre bout du doigt. Caution! Improper use or installation can cause DAMAGE OF PROPERTY. Avertissement ! Lutilisation ou linstallation inexacte peut causer DAMAGE DE PROPRIT. Caution! Do not use shielded Ethernet cable. Doing so will void the warranty. Attention ! Ne pas utiliser de cble Ethernet blind . Cela annulera la garantie. Important! Using this product in a manner other than outlined in this document voids your warranty. Further, Control4 is NOT liable for any damage incurred with the misuse of this product. See Warranty. 11 Specifications and requirements Specifications Model Numbers C4-TT7-BL, C4-TT7-WH Views Front Screen Network Power supply Resolution: 1280 800, capacitive touch Camera: 720p Ethernet or WiFi (802.11g/n [2.4 GHz]) Security: WEP, WPA/WPA2 PSK, 802.1x EAP, PEAP Notes: (1) While technically the touch screen can use 802.11b, 802.11b is not supported. (2) 802.11n is recommended for best performance. Even with 802.11n, broadcasting to several devices will degrade Video Intercom response time and images. Broadcasting to additional devices will further degrade performance. See Wireless Network Limitations. PoE (IEEE 802.3af) 13W peak 100-240VAC, 50/60 Hz International power supply adapters included Operating temperature 32 ~ 104F (0 ~ 40C) Storage temperature 4 ~ 158F (-20 ~ 70C) Charging station connections RJ-45 (PoE, Ethernet) 5VDC power Dimensions (WHD) Touch screen: 7.0 5.1 0.75" (178 130 19mm) Charging station: 4.2 2.3 3.1" (106 57 78mm) A B C A Camera LED B Camera C 7" diagonal, capacitive 1280 800 display Weight Touch screen: 0.7 lbs. (0.32 kg) Charging station: 0.8 lbs. (0.36 kg) Back Requirements A B C D A controller fully installed and configured with Control4 OS2.7.2 or later. If using Ethernet data:
Ethernet network installed and available that includes a gateway/router/switch. One Ethernet cable that runs from the Ethernet gateway/
router/switch to the touch screen If using WiFi data:
Wireless network (WiFi 802.11b/g/n) installed and available with a wireless access point (WAP). Security can be WEP, WPA/WPA2 PSK, 801.1x EAP, PEAP. If using PoE power:
Control4 PoE Injector (model #AC-POE1-B) or another third-party PoE Injector or switch (UL/ANSI certified). Two unshielded Ethernet CAT5/6 cables: (1) one that runs from the Ethernet gateway/router/switch to the PoE Injector/switch and (2) one that runs from the PoE injector/switch to the Ethernet connection in the touch screens wall box. If using AC power:
Access to AC power outlet (AC power adapter included) Wireless network (WiFi 802.11b/g/n) installed and available with a wireless access point (WAP). Security can be WEP, WPA/WPA2 PSK, 801.1x EAP, PEAP. Access to AC power outlet (AC power adapter included) E F G A Power button. Press and release to toggle screen on/off, press and hold to reboot (if attached to charging station) or turn off
(if detached from charging station) B Reset button (recessed). Use a straightened paper clip to press and release to reboot (if attached to charging station) or turn off (if detached from charging station) C Docking connector D Screw hole for permanently mounting charging station E Volume buttons F Stereo speakers G Microphone 2 Charging station bottom A B C D A Ethernet/PoE connector B 5VDC power connector C Screw hole for permanently attaching station to screen D Control4 logo LED switchControls the LED on the front of the charging station. Touch screen placement Place the touch screens charging station on any level surface. Note: Consider the angle of the touch screens camera and the sitting or standing position of the people who will use it while its on the charging station. Power and network installation options This device uses an Ethernet or WiFi network connection, and can be powered using PoE or the AC power adapter. Choose one of the following options to install the power and network communication. Caution! Do not attempt to use PoE and AC power at the same time. Choose only one power option. Attention ! Ne pas tenter dutiliser PoE et AC en mme temps. Choisir une seule option dalimentation. Option 1: Ethernet data with PoE power A PoE injector supplies power and a network connection on the Ethernet cable. Note: This installation is for a tabletop mount only, and not for portable use. Removing the touch screen from the charging station will disconnect the network. To set up your PoE and Ethernet connection with a PoE injector:
1 Attach the PoE Injector according to the instructions in your PoEs installation guide. See Connecting PoE below. 2 Pull the Ethernet cable from that location to the touch screens charging station, then connect it to the charging station. 3 Install the included ferrite bead about 6" from the end of the cable that connects to the charging station. 4 For mounting, see Tabletop-only under Mounting options below. 3 Option 2: Ethernet data with AC power The Ethernet cable connects directly to the network switch. The charging station must have access to an AC power outlet. Note: This installation is for a tabletop mount only, and not for portable use. Removing the touch screen from the charging station will disconnect the network. To set up your Ethernet connection with AC power:
1 Place the screens charging station near a power outlet. 1 Connect an Ethernet cable to the charging station and the network switch. 2 Install the included ferrite bead about 6 from the end of the cable that connects to the charging station. 3 Connect the AC power adapter to a power outlet and the charging station. 4 For mounting, see Tabletop-only under Mounting options below. Option 3: WiFi data with AC power The data connection uses WiFi, so the touch screen can be positioned anywhere in the home with a strong WiFi signal. The charging station must have access to an AC power outlet. To set up your WiFi connection and AC power:
1 Make sure you have WiFi working in the home, and place the screens charging station near a power outlet. 2 Connect the AC power adapter to a power outlet and the charging station. 3 For mounting, see Portable under Mounting options below. 4 See Configure the touch screen for wireless below. Notes: (1) Video Intercom. Although this device supports 802.11b/g/n, 802.11 b is not recommended for Video Intercom use. (2) We recommend Wireless-N for best performance. Wireless Network Limitations: Many WiFi access points handle Multicasts (WiFi simultaneously sent to multiple devices, for example, when the touch screen broadcasts video to all stations) by slowing down transmission speed to the 1 Mb basic rate. This can cause overall WiFi congestion in the WiFi network during the broadcast. Video Intercom response times and images may degrade at each device. If a home requires a large number of WiFi Video Intercom devices, ensure that you have a robust WiFi network (possibly consisting of multiple access points). Option 4: WiFi data with PoE power The data connection uses WiFi, so the touch screen can be positioned anywhere in the home with a strong WiFi signal. The charging station must have access to a PoE cable. To set up your WiFi connection with PoE power:
1 Attach the PoE Injector according to the instructions in your PoEs installation guide. See Connecting PoE below. 2 Install the included ferrite bead about 6 from the end of the cable that connects to the charging station. 4 Select each box one at a time and use the on-screen keyboard to type the IP Address, Gateway, Netmask, DNS 1
(preferred), and DNS 2 (alternate). 5 Tap SAVE when finished. Connecting PoE Connect the PoE injector to power and the network, and then connect it to the screens charging station. These instructions are for the Control4 PoE Injector (AC-POE1-B). To install a Control4 PoE injector:
1 Connect the Control4 PoE injector to an AC outlet using the power cord. 2 Connect one of the RJ-45 LAN ports on the gateway/router/
switch to the PoE Injectors LAN port using CAT5/6 Ethernet cable. 3 Connect the PoE Injectors PWR LAN-OUT port to the RJ-45 Ethernet cable that will be connected to the touch screens charging station. 4 Connect the PoE Ethernet cable to the charging station. Add and configure in Composer Pro After the touch screen is installed and appears on the home network, use Composer Pro to add it to the Control4 system and configure it. Use the Composer Pro System Design and Connections views to add and configure this device. To add and configure a T3 touch screen to a project:
1 Add the T3 7" Tabletop Touch Screen driver to your project. 2 Identify the device to the project, select the touch screen in Composer Pros Connections > Network view, click Identify, then tap Identify on the touch screen. 3 To configure the properties, select the touch screen in the System Design view, then view and change the properties in the Properties pane as needed. Properties include:
Network ConnectionReports the touch screens current network connection type. Back LightClick the arrows or type numbers to set the light level, then click Set. Advanced properties include:
Enable CameraAllows you to enable or disable the camera. 3 Make sure you have WiFi working in the home, and place the screens charging station near a power outlet. 4 For mounting, see Portable under Mounting options below. 5 See Configure the touch screen for wireless below. Configure the touch screen for wireless (optional) To configure the touch screen for wireless:
1 After initialization, tap Network. The network configuration page opens. 2 Under Wi-Fi, tap or slide OFF/ON to enable WiFi, then tap the Wi-Fi field to open a list of available networks. 3 Tap the network name you want to connect to. 4 Tap the Password field, then use the on-screen keyboard to type the password (if required). Note: If you need to enter a static IP address, follow the instructions under To set a wireless static IP address below before proceeding. 5 Tap Connect. If you dont see the network you want:
1 Tap +, then tap the Network SSID field and type the SSID
(name) of the network by using the on-screen keyboard. 2 Tap the Security field, then select the type of security to use. 3 Tap the Password field, then use the on-screen keyboard to type the password (if required). Note: If you need to enter a static IP address, follow the instructions under To set a wireless static IP address below before proceeding. 4 Tap Save. The new network is added to the bottom of the network list. To set a wireless static IP address:
1 Scroll down and tap Show advanced options. 2 Tap IPsettings, then tap Static. 3 Select each box one at a time and use the on-screen keyboard to type the:
IP address Gateway Network prefix length DNS 1 (preferred) DNS 2 (alternate) Configure the touch screen for Ethernet If you want to use DHCP (default) for your Ethernet connection, no further setup is required. To configure a static IP address for Ethernet:
1 After initialization, tap Network. The network configuration page opens. 2 Tap Ethernet. The Ethernet settings screen opens. 3 Tap Static IP Settings, then tap Use static IP. 4 Intercom (nested under the touch screen) properties:
AppearanceSelect to hide the touch screen from appearing in Navigators as an available device. BehaviorSelect the modes you want this touch screen to support. Audio ControlSelect the volume of individual audio settings. Sip InformationInformation for integrating the touch screen into your SIP/VoIP system. Custom ButtonsSelect to enable and label the two available custom buttons. Alternate CameraSelect to use an external camera for the video associated with the touch screen, for example, a security camera mounted to the side of the entrance and pointing at the door. Mounting options Place the charging station on any level surface. Consider the angle of the touch screens camera and the position of the people who will use it while its on the charging station. Portable You can set the touch screen onto the charging station for recharging and tabletop use, and lift the screen from the charging station for portable use. For this option, make sure the data connection is WiFi (see Power and network installation options above). Tabletop only For security purposes, you can permanently attach the charging station to the touch screen. For this option, we recommend using Ethernet or PoE for the data connection. To permanently attach the charging station:
1 Disconnect any cables from the charging station. 2 While holding the charging station upside-down, insert the mounting screw (included) through the mounting base and up through the mounting hole in the top. 3 Align the screw with the screw hole in the back of the touch screen, then tighten to secure it in place. Permanent mount screw hole 5 Troubleshooting Additional resources To power cycle the touch screen:
The following resources are available for more support. 1 Press and hold the
(power) button for several seconds until the touch screen turns off. 2 Press and release the
(power) button again to turn on. To perform a factory data reset:
1 On the touch screens main screen, tap Settings, System Info, then Factory data reset.
- OR -
If the touch screen has not yet been configured, tap About, then Factory data reset.
- OR -
To reset without using the display screen:
a Dock the touch screen onto its charging station. b Press and hold the volume up button while using a straightened paper clip to press and release the reset button. Reset hole Control4 Knowledgebase and forums Control4 Technical Support Control4 website: www.control4.com Composer documentation in online help or PDF formats, available on the Dealer Portal under Resources Regulatory/Safety Information To review regulatory information for your particular Control4 products, see the information located on the Control4 website at:
ctrl4.co/reg. Warranty Visit www.control4.com/warranty for details. More help For the latest version of this document, open this URL or scan the QR code on a device that can view PDFs. MOST RECENT VERSION c Keep holding down the volume up button until the icon below appears on the screen, then release the button. ctrl4.co/tt-ig d A message appears, indicating that data is being erased. Copyright 2015, Control4 Corporation. All rights reserved. Control4, the Control4 logo, the 4-ball logo, 4Store, 4Sight, Control My Home, Everyday Easy, and Mockupancy are registered trademarks or trademarks of Control4 Corporation in the United States and/or other countries. All other names and brands may be claimed as the property of their respective owners. All specifications subject to change without notice. A 200-00389-A 2015-06-11 MS control4.com | 888.400.4070 Regulatory Compliance & Safety Information for Contol4 Model C4-TT7-WH & C4-TT7-BL. Electrical Safety Advisory Scurit lectrique consultatif Important Safety Information Informations de scurit importantes Read the safety instructions before using this product. Lisez les consignes de scurit avant d'utiliser ce produit. 1. Read these instructions. 1. Lisez ces instructions. 2. Keep these instructions. 2. Conservez ces instructions. 3. Heed all warnings. 3. Respectez tous les avertissements. 4. Follow all instructions. 4. Suivez toutes les instructions. 5. Do not use this apparatus near water. 5. Ne pas utiliser cet appareil prs de l'eau. 6. Clean only with dry cloth. 6. Nettoyez-le uniquement avec un chiffon sec. 7. Do not block any ventilation openings. Install in accordance with the manufacturers instructions. fabricant. 7. Ne pas bloquer les ouvertures de ventilation. Installer conformment aux instructions du 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 8. Ne pas installer prs de sources de chaleur telles que des radiateurs, registres de chaleur, poles, ou autres appareils (incluant les amplificateurs) qui produisent de la chaleur. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 9. Ne pas contourner le dispositif de scurit de la fiche polarise ou de mise la terre. Une fiche polarise possde deux lames dont une plus large que l'autre. Une fiche de terre a deux lames et une troisime broche de terre. La lame large ou la troisime broche est fournie pour votre scurit. Si la fiche fournie ne s'adapte pas votre prise, consultez un lectricien pour le remplacement de la prise obsolte. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 10. Protgez le cordon d'alimentation ne soit pitin ou pinc, en particulier au niveau des fiches, des prises et au point o il sort de l'appareil. 11. Only use attachments/accessories specified by the manufacturer. 11. Utilisez uniquement des fixations / accessoires spcifis par le fabricant. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 12. Utilisez uniquement avec le chariot, le socle, le trpied, le support ou la table spcifis par le fabricant ou vendu avec l'appareil. Lorsque vous utilisez un chariot, soyez prudent lorsque vous dplacez l'ensemble chariot / appareil pour viter des blessures dues au renversement. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. This equipment uses AC power which can be subjected to electrical surges, typically lightning transients which are very destructive to customer terminal equipment connected to AC power sources. The warranty for this equipment does not cover damage caused by electrical surge or lightning transients. To reduce the risk of this equipment becoming damaged it is suggested that the customer consider installing a surge arrestor. 13. Dbranchez cet appareil pendant les orages ou lorsqu'il n'est pas utilis pendant de longues priodes de temps. Cet quipement utilise la puissance AC qui peuvent tre soumis des surtensions lectriques, la foudre gnralement transitoires qui sont trs destructives envers les quipements terminaux connects des sources d'alimentation CA. La garantie de cet appareil ne couvre pas les dommages causs par les surtensions lectriques ou transitoires de foudre. Pour rduire le risque de cet quipement devient endommag, il est suggr que le client envisager l'installation d'un limiteur de surtension. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 14. Confiez toutes les rparations un personnel qualifi. Une rparation est ncessaire lorsque l'appareil a t endommag de quelque faon que ce soit le cordon d'alimentation ou la fiche est endommag, du liquide a t renvers ou si des objets sont tombs dans l'appareil, l'appareil a t expos la pluie ou l'humidit, ne fonctionne pas normalement , ou s'il est tomb. 15. Use the circuit breaker to disconnect the apparatus from the AC mains. The circuit breaker shall remain readily accessible. 15. Utiliser le disjoncteur pour dconnecter l'appareil de l'alimentation secteur. Le disjoncteur doit rester facilement accessible. 16. To completely disconnect unit power from the AC mains, turn off the circuit breaker. To reconnect power, turn on the circuit breaker following all safety instructions and guidelines. 16. Pour couper entirement l'alimentation appareil de l'alimentation secteur, teignez le disjoncteur. Pour rtablir le courant, mettez le disjoncteur aprs les consignes de scurit et des lignes directrices. 17. This product relies on the buildings installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 20A. 17. Ce produit repose sur l'installation des btiments pour les courts-circuits (surintensit) de protection. Assurez-vous que le dispositif de protection est assigne ne dpassant pas:
20A. 18. CAUTION: As with all batteries, there is a risk of explosion or personal injury if the battery is replaced by an incorrect type. Dispose of used battery according to the instructions of the battery manufacturer and applicable environmental guidelines. Do not open, puncture or incinerate the battery, or expose it to conducting materials, moisture, liquid, fire or heat above 54 C or 130 F. 18. ATTENTION: Comme avec toutes les batteries, il ya un risque d'explosion ou de blessure si la batterie est remplace par un type incorrect. liminez les batteries usages selon les instructions du fabricant de la batterie et applicables des directives environnementales. Ne pas ouvrir, percer ou incinrer la batterie, ou de l'exposer des matriaux conducteurs, de l'humidit, du liquide, un incendie ou une temprature suprieure 54 C ou 130 F. 19. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. 19. N'introduisez jamais d'objets d'aucune sorte dans ce produit travers les fentes du botier car ils pourraient toucher des points de tension dangereux ou court-circuiter des pices qui pourraient entraner un incendie ou un choc lectrique. 20. This product can interfere with electrical equipment such as tape recorders, TV sets, radios, computers and microwave ovens if placed in close proximity. 20. Ce produit peut interfrer avec des appareils lectriques tels que les magntophones, tlviseurs, radios, ordinateurs et fours micro-ondes si placs proximit. The lightning flash and arrow head within the triangle is a warning sign alerting you of dangerous voltage inside the product L'clair et la flche dans le triangle est un signe d'alerte pour vous avertir d'une tension dangereuse l'intrieur du produit Caution: To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel. Attention: Pour rduire le risque de choc lectrique, ne pas retirer le couvercle
(ou l'arrire). Aucune pice rparable par l'utilisateur. Confiez l'entretien un personnel qualifi. The exclamation point within the triangle is a warning sign alerting you of important instructions accompanying the product. Le point d'exclamation dans un triangle est un signe d'avertissement vous signale des instructions importantes accompagnant le produit. See marking on bottom / back of product Voir le marquage sur les bas / dos du produit Warning!: To reduce the risk of electrical shock, do not expose this apparatus to rain or moisture AVERTISSEMENT! Pour rduire le risque de choc lectrique, n'exposez pas cet appareil la pluie ou l'humidit. Save these instructions Conservez ces instructions Compliance of this equipment is confirmed by the following label that is placed on the equipment:
Conformit de cet appareil est confirm par le symbole suivant qui est plac sur l'quipement:
USA & Canada Compliance FCC Part 15, Subpart B Unintentional Emissions Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver Increase the separation between the equipment and receiver. is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Partie 15, sous-section B Unintentional Dclaration sur les interfrences des missions Cet quipement a t test et jug conforme aux limites tablies pour un dispositif numrique de classe B, conformment la Partie 15 des rglements de la FCC. Ces limites sont conues pour fournir une protection raisonnable contre les interfrences nuisibles lorsque l'quipement est utilis dans une installation rsidentielle. Cet quipement gnre, utilise et peut mettre de l'nergie rayonnent frquence et, s'il n'est pas install et utilis conformment aux instructions, il peut causer des interfrences nuisibles aux communications radio. Cependant, il n'existe aucune garantie que des interfrences ne se produiront pas dans une installation particulire. Si cet quipement provoque des interfrences nuisibles la rception radio ou tlvision, ce qui peut tre dtermin en mettant l'quipement hors et sous tension, l'utilisateur est encourag essayer de corriger l'interfrence par une ou plusieurs des mesures suivantes:
Rorienter ou dplacer l'antenne de rception. Connecter l'quipement une prise sur un circuit diffrent de celui sur lequel le rcepteur Augmenter la distance entre l'quipement et le rcepteur. est branch. Consulter le revendeur ou un technicien radio / tlvision qualifi pour obtenir de l'aide. This device complies with part 15 of the FCC rules and Industry Canadas licence-exempt RSS-
GEN. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme partie 15 des rgles de la FCC et aux RSS- GEN d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. IMPORTANT! Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. IMPORTANT! Tous les changements ou modifications pas expressment approuvs par la partie responsable de la conformit ont pu vider lautorit de lutilisateur pour actionner cet quipement. FCC Part 15, Subpart C / RSS-210 Intentional Emissions Interference Statement Compliance of this equipment is confirmed by the following certification numbers that are placed on the equipment:
Notice: The term FCC ID: and IC: before the certification number signifies that FCC and Industry Canada technical specifications were met. The FCC ID: and IC: numbers listed below are for the WiFi module that was certified as a Limited Modular Approval. FCC ID: R33C4TT75G IC: 7848A-C4TT7 This equipment must be installed by qualified professionals or contractors in accordance with FCC Part 15.203 & IC RSS-210, Antenna Requirements. Do not use any antenna other than the one provided with the unit. FCC Partie 15, sous-partie C / RSS-210 Dclaration volontaire des missions interfrences Conformit de cet appareil est confirm par les chiffres de certification suivants qui sont placs sur l'quipement:
Avis: Le terme FCC ID:" et "IC:" devant le numro de certification signifie que les spcifications techniques de la FCC et d'Industrie Canada ont t respectes. La FCC ID: et IC: numros indiqus ci-dessous sont pour le module WiFi qui a t certifie en tant que Approbation limite modulaire. FCC ID: R33C4TT75G IC: 7848A-C4TT7 Cet quipement doit tre install par des professionnels qualifis ou entrepreneurs conformment aux normes FCC partie 15.203 & IC RSS-210, Exigences d'antenne. Ne pas utiliser une antenne autre que celui fourni avec l'appareil. RF Radiation Exposure Statement This equipment complies with the FCC/IC radiation exposure limits set fourth for portable transmitting devices operation in an uncontrolled environment. End users must follow the specific operating instructions to satisfy RF exposure compliance. This product has been tested to the FCC & IC Specific Absorption Rate (SAR) requirements of FCC 47 CFR 2.1093, IEE Std 1528-
2013, IC RSS-102 Issue 5, IEC 62209-1:2006 & IEC 62206-2:2010. This transmitter must not be co-located or operation in conjunction with any other antenna or transmitter. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. Dclaration d'exposition aux radiations RF Cet quipement est conforme aux limites d'exposition aux radiations FCC / IC dfinies quatrime pour portable opration dispositifs de transmission dans un environnement non contrl. Utilisateurs finaux doivent suivre les instructions de fonctionnement spcifiques pour satisfaire aux normes d'exposition RF. Ce produit a t test pour le Dbit d'Absorption Spcifique FCC et IC (SAR) de la FCC 47 CFR 2.1093, IEE Std 1528-2013, IC RSS-102 Issue 5, IEC 62209-1:
2006 et IEC 62206-2: 2010. Cet metteur ne doit pas tre co-localiss ou le fonctionnement en conjonction avec une autre antenne ou metteur. Les changements ou modifications non expressment approuvs par la partie responsable de la conformit pourraient annuler l'autorit de l'utilisateur utiliser cet quipement. European Compliance Conformity of the equipment with the guidelines below is attested by the application of the CE mark. Manufacturers Name:
Manufacturers Address:
CE Declaration of Conformity CONTROL4 CORPORATION 11734 S. ELECTION ROAD SUITE 200 SALT LAKE CITY UT 84020 USA EU Representative Name: CONTROL4 EMEA LIMITED EU Representative Address: UNIT3, GREEN PARK BUSINESS CENTRE SULTON-ON-THE FOREST YORK YO61 IET, UNITED KINGDOM Product Name(s):
Brand:
Model(s):
Table Top Touch Screen Contol4 C4-TT7-WH & C4-TT7-BL Product Standard(s) to which Conformity of the Council Directive(s) is declared:
EMC - 2004/108/EC Electromagnetic Compatibility (EMC) Directive:
(Emissions) EN 55022:2010, (Immunity) EN 55024:2010, EN 301 489-1 V1.9.2 (2011-09), EN 301 489-17 V2.2.1 (2012-09), EN 61000-3-2:2006 + A1:2009 + A2:2009 & EN 61000-3-3:2008 Safety 206/95/EC Low Voltage Directive (LVD):
EN 60950-1:2006/A11:2009/A1:2010/A12:2011 Telecom & Radio - 1999/5/EC Radio equipment and Telecommunications Terminal Equipment (R&TTE) Directive:
EN 300 328 V1.8.1 EN 50566:2013 & IEC/EN 62209-2:2010 RoHS - 2011/65/EU Restriction of the Use of certain Hazardous Substances in Electrical and Electronic Equipment (EEE) & WEEE - 2002/96/EC Waste of Electrical and Electronic Equipment (EEE). We, the undersigned, hereby declare that the equipment specified above conforms to the above directives and standards. Date of Issue: June 11, 2015 Legal Representative Signature Roger Midgley Sr. Regulatory Compliance Engineer Recycling Control4 understands that a commitment to the environment is essential for a health life and sustainable growth for future generations. We are committed to supporting the environmental standards, laws, and directives that have been put in place by various communities and countries that deal with concerns for the environment. This commitment is represented by combining technological innovation with sound environmental business decisions. WEEE Compliance Control4 is committed to meeting all requirements of the Waste Electrical and Electronic Equipment (WEEE) directive (2002/96/EC). The WEEE directive requires the manufacturers of electrical and electronic equipment who sell in EU countries: (1) label their equipment to notify customers that it needs to be recycled, and (2) provide a way for their products to be appropriately disposed of or recycled at the end of their product lifespan. For collection or recycling of Control4 products, please contact your local Control4 representative or dealer. About this Document Copyright 2015 Control4 Corporation. All rights reserved. Control4 and the Control4 logo are registered trademarks or trademarks of Control4 Corporation in the United States and/or other countries. Part Number 200-00415 Rev A, 6/11/2015