FCC ID: R33C4EA5V2 System controller

Control4 EA-5 Controller Installation Guide Entertainment and Automation Controller, 5 Zone Entertainment and Automation Controller, 5 Zone, V2 Supported model C4-EA5 C4-EA5-V2 Introduction The Control4 EA-5 Entertainment and Automation Controller is designed to deliver the ultimate smart home experience, featuring the highest-quality audio of the EA series and processing power to coordinate hundreds of smart devices. The EA-5 can automate sophisticated home theaters, complex interior and exterior lighting scenes, vital security and communications systems, and climate controls for multiple zones. The EA-5 features five independent audio outputstwo digital coaxial, two RCA stereo analog, and one HDMIwith an audiophile-grade signal-to-noise ratio of 118dB. A built-in music server delivers immersive, multi-stream, high-resolution audio with five built-in simultaneous audio streams from your local music collection, a variety of streaming music services, or from AirPlay-enabled devices using native Control4 ShairBridge technology. Expand beyond five streams by including additional EA-5 or EA-3 Controllers. Secure, wireless ZigBee communication; plentiful I/O including IR, serial, contacts and relays; and IP control enable connections to smart home devices such as thermostats, door locks, doorbells, cameras, security panels, sensors, lighting, shades, garage door controllers, irrigation systems, and much more. The sleek design, rack-mount form factor, and top-of-the-line connectivity make the EA-5 the ultimate foundation for any Control4 system and the platform to power the future of your smart home. Box contents The following items are included in the box:

EA-5 controller AC power cord IR emitters (8) Rack ears (2, pre-installed on the EA-5 V2) Rubber feet (2, pre-installed on the EA-5 V1) External antennas (3 with EA-5 V1, 1 with EA-5 V2) Terminal blocks for contacts and relays Accessories sold separately Control4 3.5 mm-to-DB9 Serial Cable (C4-CBL3.5-DB9B) Dual-Band WiFi USB Adapter for EA-5 V2 (C4-USBWIFI or C4-

USBWIFI-1) Warnings Caution! To reduce the risk of electrical shock, do not expose this apparatus to rain or moisture. Avertissement ! Pour rduire le risque de choc lectrique, nexposez pas cet appareil la pluie ou lhumidit. Caution! In an over-current condition on USB or contact output the software disables the output. If the attached USB device or contact sensor does not appear to power on, remove the device from the controller. Avertissement ! Dans une condition de surintensit sur USB ou sortie de contact le logiciel dsactive sortie. Si le priphrique USB ou le capteur de contact connect ne semble pas sallumer, retirez le priphrique du contrleur. Requirements and specifications Note: We recommend using Ethernet instead of WiFi for the best network connectivity. Note: The Ethernet or WiFi network should be installed before you install the EA-5 controller. Note: The EA-5 V2 requires OS 2.10.2 or higher. The EA-5 V1 requires OS 2.8.1 or higher. Composer Pro is required to configure this device. See the Composer Pro User Guide (ctrl4.co/cpro-ug) for details. Specifications Video out Video Audio out Audio playback formats High-res audio playback Audio in Inputs / Outputs 1 video out1 HDMI HDMI 1.4 output; HD 1080p, 50-60 Hz 5 audio out1 HDMI, 2 stereo analog, 2 digital coax AAC, AIFF, ALAC, FLAC, M4A, MP2, MP3, MP4/M4A, Ogg Vorbis, PCM, WAV, WMA Up to 192 kHz / 24 bit 4 audio in2 stereo analog, 2 digital coax Audio delay on audio in Advanced audio subsystem Dual audio signal processors, multiple sample rate Up to 3.5 seconds, depending on network conditions converters 10-band graphic equalizer, input gain, output gain, loudness, tone controls, balance Audio system controls

(analog or digital coax) Signal-to-noise ratio Total harmonic distortion

<-118 dBFS 0.00023 (-110 dB) Network Additional resources The following resources are available for more support. Control4 Knowledgebase: kb.control4.com and Dealer Forums:

forums.control4.com Control4 Technical Support Control4 website: www.control4.com Composer Pro documentation in online help or PDF format available on the Dealer Portal under Support: ctrl4.co/docs Front view A 1 2 3 4 M O C M O C C N O N C N O N C N O N C N O N M O C M O C B ETHERNET IN SERIAL 1 1/ 3 3 5 7 IN 1 OUT 1 C D E WIFI 1 AC POWER:

100-240 V~

60/50 Hz, 0.5 A A Data LEDThe LED indicates that the controller is streaming audio. B IR windowIR blaster and IR receiver for learning IR codes. C Caution LEDThis LED shows solid red, then blinks blue during the IN 2 OUT 1 ANALOG AUDIO IN 2 OUT 2 DIGITAL AUDIO 4 6 IR / SERIAL GIGABIT SWITCH FACTORY RESET SERIAL 2 ZIGBEE E-SATA WIFI 2 USB OUT 2 D N G D N G D N G D N G G S G S G S G S 2 1

+

2 1

+

2 1

+

2 1

+

IN 1 2/ 4 8 I I I I ID OUT boot process. Note: The Caution LED flashes orange during the factory restore process. See Reset to factory settings in this document. D Link LEDThe blue LED indicates that the controller has been identified in a Control4 Composer project and is communicating with Director. E Power LEDThe blue LED indicates that AC power is connected. The controller turns on immediately after power is applied to it. Back view Ethernet 10/100/1000BaseT compatible (required for controller setup). Built-in Ethernet switch 1 Ethernet in + 4 gigabit Ethernet switch ports AC POWER:

100-240 V~

60/50 Hz, 0.5 A WIFI 1 1 2 3 4 ETHERNET IN 1/ 3 3 5 M O C M O C C N O N C N O N C N O N C N O N M O C M O C 2 1

+

G S I 2 1

+

G S I D N G D N G 2 1

+

G S I 2 1

+

G S I D N G D N G SERIAL 1 GIGABIT SWITCH USB E-SATA WIFI 2 SERIAL 2 OUT ID FACTORY RESET 2/ 4 4 6 IR / SERIAL 7 8 IN 1 OUT 1 IN 2 OUT 2 DIGITAL AUDIO IN 1 IN 2 OUT 1 ANALOG AUDIO OUT 2 ZIGBEE WiFi WiFi security WiFi antenna ZigBee Pro ZigBee antenna eSATA port USB port IR OUT IR capture SERIAL OUT Contact Relay Internal Dual-Band Wireless-N (EA-5 V1)

(2.4GHz, 5GHz, 802.11n/g/b) (EA-5 V1) Optional Dual-Band WiFi USB Adapter (EA-5 V2)

(2.4 GHz, 5 Ghz, 802.11ac/b/g/n/a) WPA/WPA2 2 external reverse SMA connectors (EA-5 V1) 802.15.4 External reverse SMA connector 1 eSATA port 1 USB 2.0 port500mA Control 8 IR out5V 27mA max output 1 IR blasterfront 1 IR receiverfront; 20-60 KHz 4 Serial out2 DB9 ports and 2 shared with IR out 1-2 4 contact sensors2V-30VDC input, 12VDC 0.5A maximum output 4 relaysAC: 36V, 2A maximum voltage across relay;

DC: 24V, 2A maximum voltage across relay J Power requirements Power consumption Power 100-240 VAC, 60/50Hz Max: 40W, 136 BTUs/hour Idle: 15W, 51 BTUs/hour Other Operating temperature 32F ~ 104F (0C ~ 40C) Storage temperature 4F ~ 158F (-20C ~ 70C) Fan dB level Max: 35 dB Dimensions (H W D) 17.5 10.125 1.875" w/feet (444 258 49 mm) Weight Shipping weight 6.85 lbs (3.10 kg) 9.30 lbs (4.20 kg) cord. A B C D E F G H I J K L M N O A Power plug portAC power receptacle for an IEC 60320-C13 power B WIFI 1Antenna 1 for the WiFi radio (EA-5 V1 only). C Contact/Relay portConnect up to four relay devices and four contact sensor devices to the terminal block connector. Relay connections are COM, NC (normally closed), and NO (normally open). Contact sensor connections are +12, SIG (signal), and GND

(ground). D GIGABIT SWITCHFour-port gigabit ethernet switch to connect other local devices to the network. E ETHERNET INRJ-45 jack for a 10/100/1000 BaseT Ethernet connection. F USBOne port for an external USB drive or, on an EA-5 V2, the optional Dual-Band WiFi USB Adapter. See Set up external storage devices in this document. G E-SATAOne port for an external eSATA drive. See Setting up external storage devices in this document. H WIFI 2Antenna 2 for the WiFi radio (EA-5 V1 only) I SERIALTwo serial ports for RS-232 control. See Connecting the serial ports in this document. ID and FACTORY RESETID button to identify the device in Composer Pro. The ID button on the EA-5 V2 is also an LED that displays feedback useful during a factory restore. FACTORY RESET button is used to restore the controller to factory defaults. Can also reboot the controller. K HDMI OUTAn HDMI port to display system menus. Also an audio out over HDMI. L IR / SERIALEight 3.5 mm jacks for up to eight IR emitters or for a combination of IR emitters and serial devices. Ports 1 and 2 can be configured independently for serial control or for IR control. See Setting up IR emitters in this document for more information. M DIGITAL AUDIOTwo digital coax audio input and two output ports. Allows audio to be shared (IN 1 or 2) over the local network to other Control4 devices. Outputs audio (OUT 1 or 2) shared from other Control4 devices or from digital audio sources (local media or digital streaming services such as TuneIn.) N ANALOG AUDIOTwo stereo audio input and two output ports. Allows audio to be shared (IN 1 or 2) over the local network to other Control4 devices. Outputs audio (OUT 1 or 2) shared from other Control4 devices or from digital audio sources (local media or digital streaming services such as TuneIn.) O ZIGBEEAntenna for the ZigBee radio. Installing the controller To install the controller:

1 Ensure that the home network is in place before starting system setup. The controller requires a network connection, Ethernet

(recommended) or WiFi, to use all of the features as designed. When connected, the controller can access web-based media databases, communicate with other IP devices in the home, and access Control4 system updates. 2 Mount the controller in a rack or stacked on a shelf. Always allow plenty of ventilation. See Mounting the controller in a rack in this document. 3 Connect the controller to the network. EthernetTo connect using an Ethernet connection, plug the data cable from the home network connection into the controllers RJ-45 port (labeled ETHERNET IN) and the network port on the wall or at the network switch. WiFiTo connect using WiFi, first connect the controller to Ethernet, and then use Composer Pro System Manager to reconfigure the controller for WiFi. Important: Do not install your EA controller on a 172.18.xxx.xxx subnet. 4 Connect system devices. Attach IR and serial devices as described in Connecting the IR ports/serial ports and Setting up IR emitters. 5 Set up any external storage devices as described in Setting up external storage devices in this document. 6 Power up the controller. Plug the power cord into the controllers power plug port and then into an electrical outlet. Mounting the controller in a rack Using the pre-installed rack-mount ears, the EA-5 can easily be mounted in a rack for convenient installation and flexible rack placement. The pre-installed rack-mount ears can even be reversed to mount the controller facing the rear of the rack, if needed. To attach the rubber feet to the controller:

1 Remove the two screws in each of the rack ears on the bottom of the controller. Remove the rack ears from the controller. 2 Remove the two additional screws from the controller case and place the rubber feet on the controller. 3 Secure the rubber feet to the controller with three screws in each rubber foot. Pluggable terminal block connectors For the contact and relay ports, the EA-5 makes use of pluggable terminal block connectors which are removable plastic parts that locks in individual wires (included). To connect a device to the pluggable terminal block:

1 Insert one of the wires required for your device into the appropriate opening in the pluggable terminal block you reserved for that device. 2 Use a small flat-blade screwdriver to tighten the screw and secure the wire in the terminal block. Example: To add a motion sensor (see Figure 3), connect its wires to the following contact openings:

Power input to +12V Output signal to SIG Ground connector to GND Note: To connect dry contact closure devices, such as doorbells, connect the switch between +12 (power) and SIG

(signal). Connecting the contact ports The EA-5 provides four contact ports on the included pluggable terminal blocks. See the examples below to learn how to connect devices to the contact ports. Wire the contact to a sensor that also needs power (Motion sensor) Motion Sensor

+12V 0V COM NO Wire the contact to a dry contact sensor (Door contact sensor) Dry Contact Wire the contact to an externally powered sensor (Driveway sensor) External 12V Power Driveway Sensor Connecting the relay ports The EA-5 provides four relay ports on the included pluggable terminal blocks. See the examples below to learn now to connect various devices to the relay ports. Wire the relay to a single-relay device, normally open (Fireplace) Fireplace Wire the relay to a dual-relay device (Blinds) Relay 1 Relay 2 Dual-Relay Blind UP COM DOWN Connecting the serial ports The EA-5 controller provides four serial ports. SERIAL 1 and SERIAL 2 can connect to a standard DB9 serial cable. IR ports 1 and 2 (serial 3 and 4) can be reconfigured independently for serial communication. If not used for serial, they can be used for IR. Connect a serial device to the controller using the Control4 3.5 mm-to-DB9 Serial Cable (C4-

CBL3.5-DB9B, sold separately). 1 The serial ports support many different baud rates (acceptable range: 1200 to 115200 baud for odd and even parity). Serial ports 3 and 4 (IR 1 and 2) do not support hardware flow control. 2 See Knowledgebase article #268 (dealer.control4.com/dealer/

knowledgebase/article/268) for pinout diagrams. 3 To configure a ports serial settings, make the appropriate connections in your project using Composer Pro. Connecting the port to the driver will apply the serial settings contained in the driver file to the serial port. See the Composer Pro User Guide for details. Note: Serial ports 3 and 4 can be configured as straight-

through or null with Composer Pro. Serial ports by default are configured straight-through and can be changed in Composer by selecting the option Enable Null-Modem Serial Port (3/4). Setting up IR emitters The EA-5 controller provides 8 IR ports. Your system may contain third-

party products that are controlled through IR commands. The included IR emitters can send commands from the controller to any IR-controlled device. 1 Connect one of the included IR emitters into an IR OUT port on the controller. 2 Remove the adhesive backing from the emitter (round) end of the IR emitter and affix it to the device to be controlled over the IR receiver on the device. Setting up external storage devices You can store and access media from an external storage device, for example, a USB drive or eSATA drive, by connecting the USB drive to the USB port and configuring or scanning the media in Composer Pro. A NAS drive can also be used as an external storage device; see the Composer Pro User Guide (ctrl4.co/cpro-ug) for more details. Note: We support only externally powered USB drives or solid-

state USB drives (USB thumb drives). USB hard drives that do not have a separate power supply are not supported. Note: When using USB or eSATA storage devices on an EA-5 controller, a single primary partition formatted FAT32 is recommended. Composer Pro driver information Use Auto Discovery and SDDP to add the driver to the Composer project. See the Composer Pro User Guide (ctrl4.co/cpro-ug) for details. Troubleshooting Reset to factory settings Wire the relay with power from the contact, normally closed (Amplifier trigger) 12V Trigger Caution! The factory restore process will remove the Composer project. Back up the project with Composer Pro before you start the factory restore process To restore the controller to the factory default image:

1 Insert a straightened paper clip into the small hole on the back of the controller labeled FACTORY RESTORE. 2 Press and continue to hold the FACTORY RESTORE button, the controller resets and the caution LED turns solid red. 3 Hold the button until the Caution LED flashes double orange. This should take five to seven seconds. The Caution LED flashes orange while the factory restore is running. When complete, the Caution LED turns off and the device power cycles one more time to complete the factory restore process. Note: On an EA-5 V2 controller, the ID button is also an LED that provides the same feedback as the Caution LED on the front of the controller. Power cycle the controller 1 Press and hold the ID button for five seconds. The controller turns off and back on. Reset the network settings To reset the controller network settings to the default:

1 Disconnect power to the controller. 2 While pressing and holding the ID button on the back of the controller, reconnect power to the controller. 3 Hold the ID button until the Caution LED (rear ID LED) appears solid orange and the Link and Power LEDs are solid blue, and then immediately release the button. Note: In OS 2.10.1 and lower, the Caution LED appears solid blue during the network reset check. After updating to OS 2.10.2 and higher, the Caution LED appears orange during the network reset check. LED status information Power Caution Data Link Flashing LED Solid LED on EA-5 V2 only Just powered on Bootloader loaded Kernel loaded Network reset check Factory restore underway Factory restore fail Connected to Director Playing audio Regulatory/Safety information To review regulatory information for your Control4 products, see the information located on the Control4 website at ctrl4.co/reg. Warranty Visit ctrl4.co/warranty for details. More help For the latest version of this document and to view additional materials, open the URL below or scan the QR code on a device that can view PDFs. MOST RECENT VERSION MORE INFO ON EA CONTROLLERS ctrl4.co/ea5-ig ctrl4.co/ea Copyright 2018, Control4 Corporation. All rights reserved. Control4, the Control4 logo, the 4-ball logo, 4Sight, Control4 My Home, and Mockupancy are registered trademarks or trademarks of Control4 Corporation in the United States and/or other countries. All other names and brands may be claimed as the property of their respective owners. All specifications subject to change without notice. B 200-00382-B 2018-05-09 DH control4.com | 888.400.4070 Regulatory Compliance & Safety Information for Control4 Model C4-EA5-V2 Electrical Safety Advisory Scurit lectrique consultatif Important Safety Information Informations de scurit importantes Read the safety instructions before using this product. Lisez les consignes de scurit avant d'utiliser ce produit. 1. Read these instructions. 1. Lisez ces instructions. 2. Keep these instructions. 2. Conservez ces instructions. 3. Heed all warnings. 3. Respectez tous les avertissements. 4. Follow all instructions. 4. Suivez toutes les instructions. 5. Do not use this apparatus near water. 5. Ne pas utiliser cet appareil prs de l'eau. 6. Clean only with dry cloth. 6. Nettoyez-le uniquement avec un chiffon sec. 7. Do not block any ventilation openings. Install in accordance with the manufacturers instructions. fabricant. 7. Ne pas bloquer les ouvertures de ventilation. Installer conformment aux instructions du 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 8. Ne pas installer prs de sources de chaleur telles que des radiateurs, registres de chaleur, poles, ou autres appareils (incluant les amplificateurs) qui produisent de la chaleur. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 9. Ne pas contourner le dispositif de scurit de la fiche polarise ou de mise la terre. Une fiche polarise possde deux lames dont une plus large que l'autre. Une fiche de terre a deux lames et une troisime broche de terre. La lame large ou la troisime broche est fournie pour votre scurit. Si la fiche fournie ne s'adapte pas votre prise, consultez un lectricien pour le remplacement de la prise obsolte. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 10. Protgez le cordon d'alimentation ne soit pitin ou pinc, en particulier au niveau des fiches, des prises et au point o il sort de l'appareil. 11. Only use attachments/accessories specified by the manufacturer. 11. Utilisez uniquement des fixations / accessoires spcifis par le fabricant. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 12. Utilisez uniquement avec le chariot, le socle, le trpied, le support ou la table spcifis par le fabricant ou vendu avec l'appareil. Lorsque vous utilisez un chariot, soyez prudent lorsque vous dplacez l'ensemble chariot / appareil pour viter des blessures dues au renversement. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 13. Dbranchez cet appareil pendant les orages ou lorsqu'il n'est pas utilis pendant de longues priodes de temps. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 14. Confiez toutes les rparations un personnel qualifi. Une rparation est ncessaire lorsque l'appareil a t endommag de quelque faon que ce soit le cordon d'alimentation ou la fiche est endommag, du liquide a t renvers ou si des objets sont tombs dans l'appareil, l'appareil a t expos la pluie ou l'humidit, ne fonctionne pas normalement , ou s'il est tomb. 15. This equipment uses AC power which can be subjected to electrical surges, typically lightning transients which are very destructive to customer terminal equipment connected to AC power sources. The warranty for this equipment does not cover damage caused by electrical surge or lightning transients. To reduce the risk of this equipment becoming damaged it is suggested that the customer consider installing a surge arrestor. 15. Cet quipement utilise la puissance AC qui peuvent tre soumis des surtensions lectriques, la foudre gnralement transitoires qui sont trs destructives envers les quipements terminaux connects des sources d'alimentation CA. La garantie de cet appareil ne couvre pas les dommages causs par les surtensions lectriques ou transitoires de foudre. Pour rduire le risque de cet quipement devient endommag, il est suggr que le client envisager l'installation d'un limiteur de surtension. 16. To completely disconnect unit power from the AC mains, remove the power cord from the appliance coupler and/or turn off the circuit breaker. To reconnect power, turn on the circuit breaker following all safety instructions and guidelines. The circuit breaker shall remain readily accessible. 16. Pour dbrancher compltement l'alimentation secteur du rseau secteur, retirez le cordon d'alimentation du coupleur de l'appareil et / ou teignez le disjoncteur. Pour reconnecter l'alimentation, allumez le disjoncteur en suivant toutes les consignes et consignes de scurit. Le disjoncteur doit tre facilement accessible. 17. This product relies on the buildings installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 20A. 17. Ce produit repose sur l'installation des btiments pour les courts-circuits (surintensit) de protection. Assurez-vous que le dispositif de protection est assigne ne dpassant pas:

20A. 18. CAUTION: As with all batteries, there is a risk of explosion or personal injury if the battery is replaced by an incorrect type. Dispose of used battery according to the instructions of the battery manufacturer and applicable environmental guidelines. Do not open, puncture or incinerate the battery, or expose it to conducting materials, moisture, liquid, fire or heat above 54 C or 130 F. 18. ATTENTION: Comme avec toutes les batteries, il ya un risque d'explosion ou de blessure si la batterie est remplace par un type incorrect. liminez les batteries usages selon les instructions du fabricant de la batterie et applicables des directives environnementales. Ne pas ouvrir, percer ou incinrer la batterie, ou de l'exposer des matriaux conducteurs, de l'humidit, du liquide, un incendie ou une temprature suprieure 54 C ou 130 F. 19. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. 19. N'introduisez jamais d'objets d'aucune sorte dans ce produit travers les fentes du botier car ils pourraient toucher des points de tension dangereux ou court-circuiter des pices qui pourraient entraner un incendie ou un choc lectrique. 20. This product can interfere with electrical equipment such as tape recorders, TV sets, radios, computers and microwave ovens if placed in close proximity. 20. Ce produit peut interfrer avec des appareils lectriques tels que les magntophones, tlviseurs, radios, ordinateurs et fours micro-ondes si placs proximit. The lightning flash and arrow head within the triangle is a warning sign alerting you of dangerous voltage inside the product L'clair et la flche dans le triangle est un signe d'alerte pour vous avertir d'une tension dangereuse l'intrieur du produit Caution: To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel. Attention: Pour rduire le risque de choc lectrique, ne pas retirer le couvercle

(ou l'arrire). Aucune pice rparable par l'utilisateur. Confiez l'entretien un personnel qualifi. The exclamation point within the triangle is a warning sign alerting you of important instructions accompanying the product. Le point d'exclamation dans un triangle est un signe d'avertissement vous signale des instructions importantes accompagnant le produit. See marking on bottom / back of product Voir le marquage sur les bas / dos du produit Warning!: To reduce the risk of electrical shock, do not expose this apparatus to rain or moisture AVERTISSEMENT! Pour rduire le risque de choc lectrique, n'exposez pas cet appareil la pluie ou l'humidit. Save these instructions Conservez ces instructions Compliance of this equipment is confirmed by the following label that is placed on the equipment:

Conformit de cet appareil est confirm par le symbole suivant qui est plac sur l'quipement:

USA & Canada Compliance FCC Part 15, Subpart B Unintentional Emissions Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver Increase the separation between the equipment and receiver. is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Partie 15, sous-section B Unintentional Dclaration sur les interfrences des missions Cet quipement a t test et jug conforme aux limites tablies pour un dispositif numrique de classe B, conformment la Partie 15 des rglements de la FCC. Ces limites sont conues pour fournir une protection raisonnable contre les interfrences nuisibles lorsque l'quipement est utilis dans une installation rsidentielle. Cet quipement gnre, utilise et peut mettre de l'nergie rayonnent frquence et, s'il n'est pas install et utilis conformment aux instructions, il peut causer des interfrences nuisibles aux communications radio. Cependant, il n'existe aucune garantie que des interfrences ne se produiront pas dans une installation particulire. Si cet quipement provoque des interfrences nuisibles la rception radio ou tlvision, ce qui peut tre dtermin en mettant l'quipement hors et sous tension, l'utilisateur est encourag essayer de corriger l'interfrence par une ou plusieurs des mesures suivantes:

Rorienter ou dplacer l'antenne de rception. Augmenter la distance entre l'quipement et le rcepteur. Connecter l'quipement une prise sur un circuit diffrent de celui sur lequel le rcepteur Consulter le revendeur ou un technicien radio / tlvision qualifi pour obtenir de l'aide. est branch. This device complies with part 15 of the FCC rules and Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAN ICES-3(B)/NMB-3(B) Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. CAN ICES-3(B)/NMB-3(B) IMPORTANT! Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. IMPORTANT! Tous les changements ou modifications pas expressment approuvs par la partie responsable de la conformit ont pu vider lautorit de lutilisateur pour actionner cet quipement. FCC Part 15, Subpart C / RSS-247 Intentional Emissions Interference Statement Compliance of this equipment is confirmed by the following certification numbers that are placed on the equipment:

Notice: The term FCC ID: and IC: before the certification number signifies that FCC and Industry Canada technical specifications were met. C4-EA5-V2:

FCC ID: R33C4EA5V2 IC: 7848A-C4EA5V2 This equipment must be installed by qualified professionals or contractors in accordance with FCC Part 15.203 & IC RSS-247, Antenna Requirements. Do not use any antenna other than the one provided with the unit. FCC Partie 15, sous-partie C / RSS-247 Dclaration volontaire des missions interfrences Conformit de cet appareil est confirm par les chiffres de certification suivants qui sont placs sur l'quipement:

Avis: Le terme FCC ID:" et "IC:" devant le numro de certification signifie que les spcifications techniques de la FCC et d'Industrie Canada ont t respectes. C4-EA5-V2:

FCC ID: R33C4EA5V2 IC: 7848A-C4EA5V2 Cet quipement doit tre install par des professionnels qualifis ou entrepreneurs conformment aux normes FCC partie 15.203 & IC RSS-247, Exigences d'antenne. Ne pas utiliser une antenne autre que celui fourni avec l'appareil. This radio transmitter has been approved by Industry Canada to operate with the antenna type listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Manufacturer: SHEN ZHEN COS-LINK TECHNOLOGY CO., LTD Model: CSL-AN2400-100840-B01 Maximum Gain: 2.4 GHz (2 dBi) Cet metteur radio a t approuv par Industrie Canada pour fonctionner avec le type d'antenne indiqu ci-dessous avec le gain maximal admissible indiqu. Les types d'antennes non inclus dans cette liste, ayant un gain suprieur au gain maximal indiqu pour ce type, sont strictement interdits pour une utilisation avec cet appareil. Manufacturer: SHEN ZHEN COS-LINK TECHNOLOGY CO., LTD Model: CSL-AN2400-100840-B01 Maximum Gain: 2.4 GHz (2 dBi) RF Radiation Exposure Statement This equipment complies with the FCC/IC radiation exposure limits set fourth for portable transmitting devices operation in an uncontrolled environment. End users must follow the specific operating instructions to satisfy RF exposure compliance. The equipment should only be used or installed at locations where there is normally greater than a 20cm separation between the antenna and all persons. This transmitter must not be co-located or operation in conjunction with any other antenna or transmitter. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. Dclaration d'exposition aux radiations RF Cet quipement est conforme aux limites FCC / IC d'exposition aux rayonnements dfinies quatrime opration appareils portables transmettre dans un environnement non contrl. Les utilisateurs finaux doivent suivre les instructions de fonctionnement spcifiques pour satisfaire la conformit aux expositions RF. L'quipement ne doit tre utilis ou install des endroits o il est normalement suprieure une sparation de 20 cm entre l'antenne et toute personne. Cet metteur ne doit pas tre co-localiss ou fonctionnement en conjonction avec une autre antenne ou un autre metteur. Tout changement ou modification non expressment approuv par la partie responsable de la conformit pourraient annuler l'autorit de l'utilisateur utiliser cet quipement. Europe Compliance Compliance of this equipment is confirmed by the following logo that is placed on the product ID label that is placed on the bottom of the equipment. The full text of the EU Declaration of Conformity (DoC) is available on the following pages:

Recycling Control4 understands that a commitment to the environment is essential for a health life and sustainable growth for future generations. We are committed to supporting the environmental standards, laws, and directives that have been put in place by various communities and countries that deal with concerns for the environment. This commitment is represented by combining technological innovation with sound environmental business decisions. WEEE Compliance Control4 is committed to meeting all requirements of the Waste Electrical and Electronic Equipment (WEEE) directive (2002/96/EC). The WEEE directive requires the manufacturers of electrical and electronic equipment who sell in EU countries: (1) label their equipment to notify customers that it needs to be recycled, and (2) provide a way for their products to be appropriately disposed of or recycled at the end of their product lifespan. For collection or recycling of Control4 products, please contact your local Control4 representative or dealer. About this Document Copyright 2018 Control4 Corporation. All rights reserved. Control4 and the Control4 logo are registered trademarks or trademarks of Control4 Corporation in the United States and/or other countries. Part Number 200-00XXX Rev A, 7/31/2018 European Compliance (English) Conformity of the equipment with the guidelines below is attested by the application of the CE mark. Manufacturers Name:

Manufacturers Address:

CE Declaration of Conformity CONTROL4 CORPORATION 11734 S. ELECTION ROAD SUITE 200 SALT LAKE CITY UT 84020 USA EU Representative Name: CONTROL4 EMEA LIMITED EU Representative Address: UNIT3, GREEN PARK BUSINESS CENTRE SULTON-ON-THE FOREST YORK YO61 IET, UNITED KINGDOM Home Controller Control4 C4-EA5-V2 Product Name(s):

Brand:

Model(s):

Product Standard(s) to which Conformity of the Council Directive(s) is declared:

EMC - 2014/30/EU Electromagnetic Compatibility (EMC) Directive:

(Emissions) EN 55032:2015 (Immunity) EN 55024:2010+A1:2015, EN 301 489-1 V1.9.2 (2011-

09), EN 301 489-17 V2.2.1 (2012-09), EN 61000-3-2:2014 & EN 61000-3-3:2013 Safety 2014/35/EC Low Voltage Directive (LVD):

EN 60950-1:2006 + A1:2010 + A11:2009 + A12:2011 + A2:2013 Radio - 2014/53/EU Radio Equipment Directive (RED):

EN 300 328 V2.1.1 ErP - 2009/125/EC Energy-related Product Directive. RoHS - 2011/65/EU Restriction of the Use of certain Hazardous Substances in Electrical and Electronic Equipment (EEE) & WEEE - 2002/96/EC Waste of Electrical and Electronic Equipment (EEE). We, the undersigned, hereby declare that the equipment specified above conforms to the above directives and standards. Date of Issue: July 31, 2018. Legal Representative Signature Roger Midgley Sr. Regulatory Compliance Engineer Conformit europenne (French) Conformit de l'quipement avec les directives ci-dessous est atteste par l'apposition de la marque CE. Dclaration de conformit CE Le nom du fabricant:

Le fabricant Adresse:

Nom Reprsentant de l'UE: CONTROL4 EMEA LIMITED UE reprsentant Adresse: Unit3, GREEN PARK CENTRE D'AFFAIRES CONTROL4 CORPORATION 11734 S. LECTION Road Suite 200 SALT LAKE CITY UT 84020 USA Sulton-ON-THE FOREST YORK YO61 IET, ROYAUME-UNI Accueil Controller Control4 C4-EA5-V2 Nom (s) de produit:

Marque:

Modle (s):

Produit standard (s) dont la conformit de la directive du Conseil (s) est dclare:

EMC - 2014/30/EU "compatibilit lectromagntique (CEM)" UE:

(missions) EN 55032:2015 (immunit) EN 55024:2010+A1:2015, EN 301 489-1 V1.9.2 (2011-

09), EN 301 489-17 V2.2.1 (2012-09), EN 61000-3-2:2014 & EN 61000-3-3:2013 Scurit - 2014/35/EC "Directive Basse Tension (DBT)":

EN 60950-1:2006 + A1:2010 + A11:2009 + A12:2011 + A2:2013 Radio - 2014/53/EU directive quipement radio (RED):

EN 300 328 V2.1.1 ErP - 2009/125/EC lies l'nergie directive sur les produits. RoHS - 2011/65/EU limitation de l'utilisation de certaines substances dangereuses dans les quipements lectriques et lectroniques

- 2002/96/EC Dchets d'quipements lectriques et lectroniques (EEE). Nous, soussigns, dclarons que l'quipement indiqu ci-dessus est conforme aux directives et normes ci-dessus. Date de publication 31 juillet 2018. Reprsentant lgal Signature

(EEE) et DEEE Roger Midgley Ingnieur de conformit rglementaire Sr. European Compliance (German) Die Konformitt mit den folgenden Richtlinien wird durch die Anwendung des CE-Kennzeichen besttigt. CE-Konformittserklrung Home Controller Control4 C4-EA5-V2 Control4 CORPORATION 11734 S. WAHL ROAD SUITE 200 SALT LAKE CITY UT 84020 USA Control4 EMEA LIMITED Unit3, GREEN Park Geschftszentrum Sulton-ON-THE FOREST YORK YO61 IET, VEREINIGTES KNIGREICH Name des Herstellers:

Adresse des Herstellers:

EU-Vertreter Name:

EU-Vertreter Adresse:

Produkt-Name (n):

Marke:

Modell (e):

Produkt-Norm (en), um die Konformitt der Richtlinie (n) deklariert ist:

EMC - 2014/30/EU "Elektromagnetische Vertrglichkeit (EMV) Die Richtlinie":

(Emissionen) EN 55032:2015 (Immunitt) EN 55024:2010+A1:2015, EN 301 489-1 V1.9.2

(2011-09), EN 301 489-17 V2.2.1 (2012-09), EN 61000-3-2:2014 & EN 61000-3-3:2013 Sicherheit - 2014/35/EC "Niederspannungsrichtlinie (LVD)":

EN 60950-1:2006 + A1:2010 + A11:2009 + A12:2011 + A2:2013 Radio - 2014/53/EU ber Funkanlagen-Richtlinie (RED):

EN 300 328 V2.1.1 ErP - 2009/125/EC Energiebezogene Produktrichtlinie. RoHS - 2011/65/EU zur Beschrnkung der Verwendung bestimmter gefhrlicher Stoffe in Elektro- und Elektronikgerten (EEE) & WEEE - 2002/96/EC Richtlinie ber Elektro- und Elektronikgerten (EEE). Wir, die Unterzeichneten, erklren hiermit, dass das oben angegebene Gert zu den oben genannten Richtlinien und Normen. Ausstellungsdatum: 31. Juli 2018 Gesetzlicher Vertreter Stempel, Unterschrift Roger Midgley Sr. Regulatory Compliance-Ingenieur Conformit Europea (Italian) Conformit del materiale con le linee guida qui sotto attestata dall'applicazione del marchio CE. Dichiarazione di conformit CE Casa controller Control4 C4-EA5-V2 Sulton-ON-THE FOREST YORK YO61 IET, REGNO UNITO Control4 CORPORATION 11734 S. ELEZIONI STRADA SUITE 200 SALT LAKE CITY UT 84020 Stati Uniti d'America Nome del produttore:

Indirizzo del produttore:

UE Nome Rappresentante: Control4 EMEA LIMITED UE Indirizzo Rappresentante: Unit3, GREEN PARK BUSINESS CENTRE Nome del prodotto (s):

Marca:

Modello (s):

Prodotto standard (s) a cui conformit della direttiva del Consiglio (s) dichiarato:

EMC - 2014/30/EU "Compatibilit elettromagnetica (EMC)":

(Emissioni) EN 55032:2015 (immunit) EN 55024:2010+A1:2015, EN 301 489-1 V1.9.2 (2011-

09), EN 301 489-17 V2.2.1 (2012-09), EN 61000-3-2:2014 & EN 61000-3-3:2013 Sicurezza - 2014/35/EC "Direttiva bassa tensione (LVD)":

EN 60950-1:2006 + A1:2010 + A11:2009 + A12:2011 + A2:2013 Radio - 2014/53/EU Direttiva sulle apparecchiature radio dell'UE (RED):

EN 300 328 V2.1.1 ErP - 2009/125/EC Energy legati direttiva sui prodotti. RoHS - 2011/65/EU Limitazione / UE dell'uso di determinate sostanze pericolose nelle apparecchiature elettriche ed elettroniche (AEE) e RAEE - 2002/96/EC sui rifiuti di apparecchiature elettriche ed elettroniche (AEE). I sottoscritti, dichiariamo che l'apparecchiatura specificata in precedenza conforme alle direttive e norme di cui sopra. Data di pubblicazione: 31 luglio 2018 Rappresentante legale Firma Roger Midgley Suor Conformit alle normative Ingegnere Conformidad Europea (Spanish) La conformidad de los equipos con las siguientes pautas es atestiguado por la aplicacin de la marca CE. Declaracin de conformidad CE Control4 EMEA LIMITED Controlador Inicio Control4 C4-EA5-V2 Sulton-EN-EL BOSQUE YORK YO61 IET, REINO UNIDO Control4 CORPORACIN 11734 S. ELECCIN Road Suite 200 SALT LAKE CITY UT 84020 EE.UU. Nombre del fabricante:

Direccin del fabricante:

UE Nombre Representante:

Direccin Representante de la UE: Tema 3., VERDE PARQUE EMPRESARIAL CENTRO Nombre (s) del producto:

Marca:

Modelo (s):

Producto estndar (s) a la que la conformidad de la Directiva del Consejo (s) se declara:

EMC - 2014/30/EU "Directiva de compatibilidad electromagntica (EMC)":

(Emisiones) EN 55032:2015 (inmunidad) EN 55024:2010+A1:2015, EN 301 489-1 V1.9.2

(2011-09), EN 301 489-17 V2.2.1 (2012-09), EN 61000-3-2:2014 & EN 61000-3-3:2013 Seguridad - 2014/35/EC "Directiva de Baja Tensin (LVD)":

EN 60950-1:2006 + A1:2010 + A11:2009 + A12:2011 + A2:2013 Radio - 2014/53/EU Directiva de Equipos de Radio de la UE (RED):

EN 300 328 V2.1.1 ErP - 2009/125/EC relacionados con energa / CE Directiva del producto. RoHS - 2011/65/EU restriccin del uso de ciertas sustancias peligrosas en equipos electrnicos (AEE) y WEEE elctricos y / UE - 2002/96/EC de Residuos de Aparatos Elctricos (AEE) y electrnicos. Nosotros, los abajo firmantes, declaramos por la presente que el equipo anteriormente mencionado se ajusta a las directrices y estndares anteriores. Fecha de emisin: 31 de julio de 2018 Representante legal Firma Roger Midgley Ingeniero Sr. Cumplimiento de la normativa Conformidade Europeia (Portuguese) Conformidade do equipamento com as diretrizes abaixo atestada pela aplicao da marca CE. Declarao de Conformidade CE Control4 EMEA LIMITED Incio Controlador Control4 C4-EA5-V2 Sulton-ON-THE FOREST YO61 IET YORK, REINO UNIDO Control4 CORPORATION 11734 S. ELEIO ROAD SUITE 200 SALT LAKE CITY UT 84020 EUA Nome do fabricante:

Do fabricante Endereo:

Representante da UE Nome:

Representante da UE Endereo: UNIT3, GREEN PARK CENTRO DE NEGCIO Nome (s) produto:

Marca:

Modelo (s):

Padro do produto (s) a que Conformidade da Directiva do Conselho (s) declarado:

EMC - 2014/30/EU "Compatibilidade Electromagntica (EMC)":

(Emisses) EN 55032:2015 (Imunidade) EN 55024:2010+A1:2015, EN 301 489-1 V1.9.2 (2011-

09), EN 301 489-17 V2.2.1 (2012-09), EN 61000-3-2:2014 & EN 61000-3-3:2013 Segurana - 2014/35/EC "Directiva de Baixa Tenso (LVD)":

EN 60950-1:2006 + A1:2010 + A11:2009 + A12:2011 + A2:2013 Rdio - 2014/53/EU Directiva equipamento de rdio (RED):

EN 300 328 V2.1.1 ERP - 2009/125/EC relacionados Energy-/ CE Directiva do produto. RoHS - 2011/65/EU Restrio do Uso de Certas Substncias Perigosas em Equipamentos Elctricos e Electrnicos (EEE) e WEEE - 2002/96/EC de Resduos de Equipamentos Elctricos e Electrnicos (EEE). Ns, abaixo-assinado, declaro que o equipamento especificado acima est em conformidade com as diretrizes e normas acima referidas. Data de Emisso: 31 de julho de 2018 Representante legal Assinatura Roger Midgley Sr. Engenheiro Conformidade Regulatria