FCC ID: R33C4TW7C0 TOUCH SCREEN INTERFACE DEVICE

7 In-Wall Touch Screen with Camera Installation Guide Introduction The Control4 7 In-Wall Touch Screen with Camera offers complete system control in an elegant and compact design. This Touch Screen is equipped with a capacitive Touch Screen and four (4) programmable shortcut buttons plus Audio and Video Intercom (with a built-in camera) using SIP. The available power options are AC power or Power-

over-Ethernet (PoE); the network options are WiFi or Ethernet connections. This Touch Screen supports new construction or retrofit installations. AC. AC power is used to power the Touch Screen when using an Ethernet or WiFi network connection. PoE. PoE is used to power the Touch Screen when using an Ethernet or WiFi network connection. The following table shows the available network options with power. Ethernet with PoE Ethernet with AC WiFi with AC NOTE: Video Intercom using 802.11b is not recommended or supported for Video Intercom. Control4 recommends Wireless-N for Video Intercom. See Wireless Network Limitations and Power and Network Installation Options. Option 1: Ethernet with PoE. The Ethernet network connection is provided through the PoE Injector. No additional wiring is needed. Option 2: Ethernet with AC. Connect the Touch Screen to one of the RJ-45 LAN ports on the gateway/router using the RJ-45 Ethernet cable. Option 3: WiFi with AC. The internal WiFi will communicate with the LANs WAP. If the LAN has a WAP set up, no additional wiring is needed. Supported Models C4-TW7C0- BL - 7 Inch Wall Mount Capacitive Touch Screen with Camera, Ethernet/WiFi, PoE/

Universal Voltage, Black C4-TW7C0- WH - 7 Inch Wall Mount Capacitive Touch Screen with Camera, Ethernet/WiFi, PoE/

Universal Voltage, White Associated SKUs:

C4-TSWMC5-EG-WH 5 In-Wall Touch Screen, White (no camera) C4-TSWMC7-EG-WH 7 In-Wall Touch Screen, White (no camera) C4-TSWMC5-EG-BL 5 In-Wall Touch Screen, Black (no camera) C4-TSWMC7-EG-BL 7 In-Wall Touch Screen, Black (no camera) Box Contents Carefully unpack the contents of the box, and make sure the following items are included. If any item is missing or damaged, please contact your Control4 Reseller. 7 In-Wall Touch Screen with Camera Power box (used to power the Touch Screen) Two (2) screws to attach the power box Warranty card 1 7 In-Wall Touch Screen with Camera Installation Guide Accessories PoE. Control4 Power over Ethernet Injector, sold separately (AC-POE1-B). Back Box Options. There are four (4) back box options available for this Touch Screens installation. Metal and plastic back boxes are available for new construction or retrofit installations. 5 and 7 In-Wall Touch Screen Back Box Kits -

New Construction

- 5 and 7 In-Wall Touch Screens Wall Box, New Construction, Plastic (C4-NWB57C-P)

- 5 and 7 In-Wall Touch Screens Wall Box, New Construction, Metal (C4-NWB57C-M) 5 and 7 In-Wall Touch Screen Back Box Kit -

Retrofit

- 5 and 7 In-Wall Touch Screens Wall Box, Retrofit, Plastic (C4-RWB57C-P)

- 5 and 7 In-Wall Touch Screens Wall Box, Retrofit, Metal (C4-RWB57C-M) See the Control4 5 or 7 In-Wall Touch Screen Wall Box Installation Guide - New Construction or 5 or 7 In-Wall Touch Screen Wall Box Installation Guide - Retrofit for back box installation details. Specifications Screen Wireless 7 16:9 wide VGA Color LCD Module Resolution: 800 x 480 Camera: 640 x 480 VGA Brightness: 350 nits Built In IEEE802.11 b/g/n Wireless LAN Integral Antenna (b/g/n supported) Authentication: WEP, WPA, WPA2 2 Dimensions

(H x W x D) Weight 4.88 x 7.2 x .60 (124 mm x 183 mm x 15.24 mm) 1.15 lbs. (.52 kg) Shipping Weight 1.8 lbs. (.81 kg) Network WiFi (802.11 b/g/n) wireless access point (WAP) already configured to communicate with a Control4 Controller (e.g., HC-800). Wireless-N is recommended for Video Intercom. Notes: (1) Intercom usage. 802.11b is not recommended or supported for Video Intercom. (2) Wireless-N is recommended for Video Intercom. Even with Wireless-N, broadcasting to several devices will degrade Video Intercom response time and images. Broadcasting to additional devices will further degrade performance. See Wireless Network Limitations. Requirements To install the 7 In-Wall Touch Screen with Camera, Control4 requires the following:

A Home Controller fully installed and configured with a Control4 system. Control4 7 Touch Screen custom back box installed (OS 2.2.1 or later). See Accessories. If using Ethernet with PoE power:

- Ethernet network installed and available that includes a gateway/router/switch

- Control4 PoE Injector (model #AC-POE1-B) or another third-party PoE Injector or switch

(certified to UL/ANSI standards).

- Two (2) Ethernet CAT5 cables: (1) one that runs from the Ethernet gateway/router/switch to the PoE Injector/switch and (2) one that runs from the PoE Injector/switch to the Ethernet connection in the Touch Screens back box. If using Ethernet with AC power:

- Ethernet network installed and available that includes a gateway/router/switch

- Access to in-wall AC power (a neutral connection is required)

- One (1) Ethernet CAT5 cable that runs from the Ethernet gateway/router/switch to the Touch Screen

- A 14-gauge electrical wire long enough to pull between the Touch Screen and the power source If using wireless with AC power:

- Wireless network (WiFi 802.11 b/g/n) installed and available with a wireless access point (WAP)

- Access to in-wall AC power (a neutral connection is required)

- A 14-gauge electrical wire long enough to pull between the Touch Screen and the power source Back View Figure 2. Back View - 7 In-Wall Touch Screen with Camera and Power Box Front and Rear Panel Descriptions Front View Figure 1. Front View - 7 In-Wall Touch Screen 3 4 1 2 2 1 1 Wire Connection. Hot (H) uses Black wire; Return

(R) uses White wire. 2 RJ-45 port for Ethernet Connection. Ethernet port available for either a standard Ethernet source that provides network communication only OR a PoE source that provides power to the device and network communication. 1 Display. 7 viewing area, Touch Screen with 800 x Touch Screen Placement 480 resolution. 2 Shortcut buttons (4). For custom programming;

to initiate an action or sequence of actions. Use Composer Pro or Composer HE to configure these buttons. 3 Green LED. Lets you know the camera is on. 4 Camera. For Video Intercom calls. Dimensions

- Front dimensions. 7 Touch Screen (H x W x D):

4.88 x 7.2 x .60 (124 mm x 183 mm x 15.24 mm)

- Back box dimensions. 7 Touch Screen

(H x W x D): 2.7 x 4.1 x 2.4 (68 mm x 104 mm x 61 mm)

- Power box dimensions. 7 Touch Screen (H x W x D): 2.8 x 4.5 x 1.8 (71 mm x 114 mm x 46 mm) Touch Screen Removal Use the small hole located under the Touch Screen to remove the Touch Screen from the wall (for details, see Figure 10 in Troubleshooting). Place the Touch Screen in a convenient location at eye level, typically near the entrance of the room, approximately 57 to 61 inches (145 cm to 155 cm) from the floor (see Figure 3). NOTE: Consider the camera on the panel and the height of the people in the home who will use the camera for Video Intercom. Figure 3. Touch Screen Placement New Device AC Power

(unless using PoE) LED Indicator The LED on the Touch Screen indicates the camera status of the camera and booting information as described in the next table. 3 Camera LED Color/

Touch Screen Status State Off Green Green (blinks slowly) Green (blinks rapidly)

- Camera is off

- Camera is on

- Booting up

- Restoring (during a factory restore) Installation WARNING! Before installing the Touch Screen, switch off the circuit breaker or remove the fuse from the fuse box. AVERTISSEMENT! Pour lendroit o vous installez lcran tactile, coupez le disjoncteur ou enlevez le fusible de la bote de fusible. IMPORTANT! Before you can complete the instructions below, you must have a 7 Touch Screen back box installed according to the documentation provided in the back box kit. See Accessories for details. IMPORTANT! En coupant louverture pour la bote de mur, ne coupez pas louverture trop grande. Soyez conservateur et agrandissez-

avec prcaution la comme ncessaire. Voyez que <<Accessories>>. IMPORTANT! When cutting the opening for the back box, DO NOT cut the opening too large. Be conservative and cautiously enlarge it as needed. IMPORTANT! En coupant louverture pour la bote de mur, ne coupez pas louverture trop grande. Soyez conservateur et agrandissez-

avec prcaution la comme ncessaire. Power and Network Installation Options This device uses an Ethernet or WiFi network connection, and can be powered using PoE or AC power. Choose one of the following options to install the power and network communication. CAUTION! Do not attempt to use PoE and AC power at the same time. Choose only one power option. ATTENTION! Ne pas tenter dutiliser PoE et AC en mme temps. Choisir une seule option dalimentation. Option 1: Ethernet Connection with a PoE Injector or a Third-Party Injector or Switch PoE supplies DC power on the Ethernet cable using a PoE Injector (model #AC-POE1-B) or a third-party PoE solution to provide the Touch Screen with power and a network connection. The Touch Screen works with the Control4 PoE Injector or a third-party PoE Injector. To set up your PoE and Ethernet connection with a PoE Injector, see Figure 4. 1 Attach the PoE Injector according to the instructions in your PoEs installation guide if provided. Control4 PoE Injector instructions are provided later in this document. 2 Pull the Ethernet cable from that location to where you want to install the Touch Screen. Figure 4. Ethernet with PoE - Requires Ethernet Connection to PoE Injector Option 2: Ethernet Connection with AC The Ethernet is connected directly to the switch

(see Figure 5). This power connection requires both neutral and hot connections. 4 Figure 5. Ethernet - Requires a Connection to Ethernet and AC Power Figure 6. WiFi - Requires AC Power and WAP Option 3: WiFi Connection with AC Place the Touch Screen above a power source, for example, an outlet. Ensure that you have WiFi in the home (see Figure 6). NOTES: (1) Video Intercom. Although this device supports b/g/n, 802.11 b is not supported for Video Intercom use. (2) Wireless-N is recommended for Video Intercom. See the Composer Pro User Guide for details about the 7 In-Wall Touch Screen with Camera properties. Wireless Network Limitations Many WiFi Access Points handle Multicasts

(WiFi simultaneously sent to multiple devices, for example, when the 7 In-Wall Touch Screen with Camera broadcasts video to all stations) by slowing down transmission speed to the 1 Mb basic rate. This can cause overall WiFi congestion in the WiFi network during the broadcast. Video Intercom response times and images may degrade at each device. If a home requires a large number of WiFi Video Intercom devices, ensure that you have a robust WiFi network (possibly consisting of multiple access points). Power Installation Prepare the plastic power box for installation into the back box by inserting either the Ethernet cable or the AC power cable into the power box (see Figures 7 and 8), and then follow the instructions next. AC Power Connection The steps below represent a typical U.S. installation. 1 Connect the wires to the AC power source for the Touch Screen according to the national and local electrical codes. Installation may require alternative wires and the use of a terminal block. 2 Thread the power cable through the bottom back hole of the back box to the terminal block (see Figure 7). 3 Strip the black and white power wire ends to 1/4 as necessary. Using a flathead screwdriver, loosen the screws on the power boxs terminal block and connect the power wires to each terminal (see Figure 7). 4 Cap the ground wire from the wall if you are using a plastic back box. Attach the ground wire to the back box if using a metal back box. Figure 7. AC Power Connection Power Box Terminal Block Connect Wires to Terminal Block Back Box Power Cable 5 5 Align and bend the wires carefully to fit them Figure 8. Ethernet Connection inside the back box. 6 Align and carefully slide the power box into the back box. 7 Secure the power box into the back box using the screws provided. NOTE: Overtightening the power box screws could result in a poor connection between the Touch Screen and the power box and could also cause the Touch Screen to warp. 8 Align and slide the back of the Touch Screen into 9 the power box. The Touch Screen is magnetic and should snap into place easily.

(Optional) To secure the Touch Screen inside the power box, remove the tape covering the bottom security pin (see Figure 10) before attaching the Touch Screen to the power box. Power Over Ethernet (PoE) Connection Connect the PoE Injector to power and the network, and then connect it to the power box. Ethernet Connection Power Box Back Box 6 Secure the power box into the back box using the screws provided. NOTE: Overtightening the power box screws could result in a poor connection between the Touch Screen and the power box and could also cause the Touch Screen to warp. 7 Align and slide the back of the Touch Screen into 8 the power box. The Touch Screen is magnetic and should snap into place easily.

(Optional) To secure the Touch Screen inside the power box, remove the tape covering the bottom security pin (see Figure 10) before attaching the Touch Screen to the power box. The steps below describe how to install a Control4 PoE Injector. Configuration Configure for Wireless

(WiFi only) Connect to a WAP on the Touch Screen

(see Figure 9):

Figure 9. Wireless Configuration 1 Connect the Control4 PoE Injector to an AC outlet using the power cord. 2 Connect one of the RJ-45 LAN ports on the gateway/router/switch to the PoE Injectors LAN port using the RJ-45 Ethernet cable. 3 Connect the PoE Injectors PWR LAN-OUT port to the RJ-45 Ethernet cable that will be connected to the Touch Screen. 4 Pull the Ethernet cable through the top back hole of the back box to the Ethernet connector on the top back of the power box, and then connect it

(see Figure 8). 5 Align and carefully slide the power box into the back box until the Touch Screen is attached to the power box. 1 After initialization, press and hold the large White 4 in the center of the Touch Screen to enter the configuration screen. 2 Press the Network button on the Touch Screens 6 configuration page. The network configuration screen displays. 3 Under Wireless, select Enable. If you dont see the network you want, select Other. 4 At Network Name, select to add the SSID or wireless network when the keyboard appears. Select Done. 5 At Security, select None, WEP 64, WEP 128, WPA, or WPA2. 6 At Password, type the password on the keyboard that appears. Press Done. 7 Select Connect. Notice that the IP settings 8 change. The IP address is set to DHCP by default.

(Optional) If you need to set a static IP address instead, complete the following steps:

a On the Network page, press Static. b Select each box one at a time and type the address: IP Address, Subnet Mask, Default Gateway, Preferred DNS, and Alternate DNS. c When the keyboard appears, type the address, and then press Done. 9 Press OK to return to the Network page. You can now connect to a Control4 Director running on a Control4 device on the network. 10 Press OK. Configure in Composer Pro When the Touch Screen is physically installed and appears on the home network, you can add and configure it for the Control4 System using Composer Pro. Choose the In-Wall 7 Touch Screen V2 driver in Composer and add it to your project. See the Composer Pro User Guide for information about how to add and identify the Touch Screen to the Control4 System. Restore to Factory Default If the cameras LED blinks on and off for more than 30 seconds, the device will need to be restored. To access the Factory Restore switch, youll first need to remove the Touch Screen. NOTE: If theres tape on the bottom of the power box, simply lift the Touch Screen off

(see Steps 3 through 6). Remove the tape to lock the Touch Screen in place. If theres no tape, the Touch Screen is locked into place. In this case, follow the instructions below. 1 Locate the small hole underneath the Touch Screens faceplate (see Figures 10 - 13). Figure 10. Touch Screen Underside - Pin and Pinhole Security pin Speaker Insert paper clip here to remove Touch Screen 2 Using a small unbent paper clip, insert the paper clip straight up and into the small hole (about 1/4) or as far as you can. Theres another small hole inside the Touch Screen which the paper clip needs to insert into also (see Figures 11 through 13). You may need to wiggle the paper clip a bit to get it into the second small hole. Figure 11. Locate Touch Screen Hole Insert Paper Clip Here Bottom of Touch Screen Troubleshooting Boot Up Insert Paper Clip Through this Hole Too When the device is booting up, it may take 30 seconds or longer before the Green LED turns on. When it turns on, it blinks slowly for a time and then turns off. After that, you will see an image on the Touch Screen. 7 Figure 12. Insert Paper Clip Through Small Hole Figure 13. Paper Clip Needs to Engage Release Plate Security plate Pinhole 3 With both hands, tilt the bottom of the Touch 1:1 SCALE Screen out and gently remove the Touch Screen. 4 On the back of the Touch Screen locate the small C4-7 TOUCH SCREEN IN WALL-V2 switch (see Figure 14). Figure 14. Factory Restore Switch Factory Restore Switch 5 Using the tip of a straight pin or paper clip, change the position of the switch, for example, if the switch is in the down position, push it to the up position. The Touch Screen will then sense the 8 change on the next power up, and will initiate the restore process. 6 When you are finished with the restore, reattach the Touch Screen into the power box in the wall top firstand then snap the bottom of the Touch Screen back into place. 7 The Touch Screen will reboot and the factory default firmware image will be installed. All settings will reset to the factory default settings. See LED Indicator for information about how the LED behaves during a factory restore. 8 After a restore, the Touch Screen will need to be updated to the same image version of the project

(e.g., OS 2.2.2 or later). Warnings/Considerations WARNING! The Touch Screen must be protected by an external circuit breaker or a fuse rated at 6A maximum when used in Europe. AVERTISSEMENT! Pour rduire le risque du feu ou de choc lectrique, nexposez pas cet appareil la pluie ou lhumidit. WARNING! Do not place the Touch Screen near sources of heat or expose to direct sunlight for an extended period of time. AVERTISSEMENT! Ne placez pas lunit prs des sources de chaleur ou exposition pour diriger la lumire du soleil pendant une priode prolonge. IMPORTANT! Do not use pens or sharp objects to navigate or make selections on the Touch Screen. To select an item or scroll through a list, use your fingertip. IMPORTANT! Nemployez pas les stylos ou les objets pointus pour diriger ou pour faire des choix sur lcran. Pour choisir un article ou un rouleau par une liste, employez votre bout du doigt. IMPORTANT! Improper use or installation can cause DAMAGE OF PROPERTY. IMPORTANT! Lutilisation ou linstallation inexacte peut causer DAMAGE DE PROPRIT. IMPORTANT! Using this product in a manner other than outlined in this document voids your warranty. Further, Control4 is NOT liable for any damage incurred with the misuse of this product. See Warranty. IMPORTANT! Utilisant ce produit en quelque sorte autre que dcrit dans ce document vide votre garantie. De plus, Control4 nest pas responsable daucun dommage encouru avec labus de ce produit. Voyez que Warranty. WARNING! Install in accordance with all national, state, and local electrical CODES. AVERTISSEMENT! Installez selon tous les national, tat, et codes lectriques locaux. WARNING! This product generates heat. The room must have adequate VENTILATION or the ability to dissipate heat effectively. AVERTISSEMENT! Ce produit produit de la chaleur. La salle doit avoir VENTILATION proportionne ou la capacit dabsorber la chaleur efficacement. WARNING! This product must be grounded in accordance with the National Electrical Code

(NEC) requirements. AVERTISSEMENT! Ce produit doit tre fondu selon les conditions lectriques nationales de code (NEC). WARNING! Use this product only in dry locations. AVERTISSEMENT! Employez ce produit seulement dans des endroits secs. CAUTION! This product is for residential use only. ATTENTION! Ce produit est pour lusage rsidentiel ou commercial seulement. MAGNET WARNING! Located within the plastic enclosures of this product are strong

(rare earth) magnets that are used to attach the face plate to the electrical box. If someone handling or using the product has a pacemaker, defibrillator, or similar electronic device used for health purposes, avoid close proximity (closer than 20 inches) to the product until you consult your physician. Magnetic fields can cause damage to magnetic storage media (for example, credit cards, video tapes, computer hard drives, etc). Keep all magnets at least 20 inches away from all types of magnetic media. Certain electronic devices are sensitive to magnetic FIELDS and may be damaged permanently or temporarily disabled if exposed to a magnetic field that is too strong. Consult the owners manuals of your electronic devices for further information. INGESTED magnets can cause serious injuries and may result in death. If magnets have been ingested (or you suspect they might have been), seek competent medical attention immediately. AVERTISSEMENT! Aimants! Dans lemballage en plastique de ce produit sont inclus des aimants trs puissants utiliss pour attacher les plaques de surface aux boites lectriques. Si quelquun, manipulant ou utilisant ce produit est muni dun pacemaker, dfibrillateur ou autre dispositif dordre mdical, il doit viter de se trouver proximit (moins de 20 pouces) de ce produit avant davoir consult son mdecin. Les champs magntiques des aimants peuvent endommager le stockage dinformation dordre magntique (ex :

cartes de crdit, bandes vido, disques durs dordinateur, etc.) Gardez tous les aimants au moins 20 pouces de distance de tout type de stockage dinformation dordre magntique. Certains dispositifs lectroniques sont sensibles aux champs magntiques et peuvent tre endommags de faon permanente ou tre dsactivs si ils sont exposs un champs magntique trop puissant. Pour plus dinformation, consultez le manuel dutilisateur propre votre pice lectronique. SI avals, les aimants peuvent causer des blessures graves et aussi causer la mort. Si des aimants ont t avals (ou vous doutez quils ont pu ltre) obtenez les soins mdicaux de personnes comptentes immdiatement. 9 About this Document Part Number: 200-00288, Rev B, 6/11/2012 Third-Party Trademarks Libertas Libertas Firmware copyright statement for Touch Screens 6/26/09 Copyright (c) 2006, One Laptop per Child and Marvell Corporation. All rights reserved. Redistribution. Redistribution and use in binary form, without modification, are permitted provided that the following conditions are met:

* Redistributions must reproduce the above copyright notice and the following disclaimer in the documentation and/or other materials provided with the distribution.

* Neither the name of Marvell Corporation nor the names of its suppliers may be used to endorse or promote products derived from this software without specific prior written permission.

* No reverse engineering, decompilation, or disassembly of this software is permitted.

* You may not use or attempt to use this software in conjunction with any product that is offered by a third party as a replacement, substitute or alternative to a Marvell Product where a Marvell Product is defined as a proprietary wireless LAN embedded client solution of Marvell or a Marvell Affiliate. DISCLAIMER. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS AS IS AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;

LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. GNU GNU GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION (Section 3.b.) You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following:

Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 on a medium customarily used for software interchange. The complete text for this license is available on the Control4 website at: http://

www.control4.com. Regulatory/Safety/Other Information To review regulatory information for your particular Control4 products, see the information located on the Control4 website at:

http://www.control4.com/regulatory/. Patent Information Protected under U.S. Patents 7,335,845, 7,106,261 and licensed under U.S. Patents 5,905,442 and 5,982,103 Warranty Limited 2-year Warranty. Refer to http://www.control4.com/warranty. 10 2012 Control4. All rights reserved. Control4, the Control4 logo, the Control4 iQ logo and the Control4 certified logo are registered trademarks or trademarks of Control4 Corporation in the United States and/or other countries. All other names and brands may be claimed as the property of their respective owners. control4.com |

Regulatory Compliance & Safety Information for Contol4 Model C4-TW7C0-XX. Electrical Safety Advisory Important Safety Information Read the safety instructions before using this product. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturers instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. This equipment uses AC power which can be subjected to electrical surges, typically lightning transients which are very destructive to customer terminal equipment connected to AC power sources. The warranty for this equipment does not cover damage caused by electrical surge or lightning transients. To reduce the risk of this equipment becoming damaged it is suggested that the customer consider installing a surge arrestor. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. Use the mains plug to disconnect the apparatus from the AC mains. The mains plug shall remain readily operable. 16. To completely disconnect unit power from the AC mains, disconnect the units power cord from the mains socket. To reconnect power, plug the units power cord into the mains socket following all safety instructions and guidelines. 17. CAUTION: As with all batteries, there is a risk of explosion or personal injury if the battery is replaced by an incorrect type. Dispose of used battery according to the instructions of the battery manufacturer and applicable environmental guidelines. Do not open, puncture or incinerate the battery, or expose it to conducting materials, moisture, liquid, fire or heat above 54 C or 130 F. 18. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. 19. This product can interfere with electrical equipment such as tape recorders, TV sets, radios, computers and microwave ovens if placed in close proximity. The lightning flash and arrow head within the triangle is a warning sign alerting you of dangerous voltage inside the product Caution: To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel. The exclamation point within the triangle is a warning sign alerting you of important instructions accompanying the product. See marking on bottom / back of product Warning!: To reduce the risk of electrical shock, do not expose this apparatus to rain or moisture AVERTISSEMENT! Pour rduire le risque de choc lectrique, n'exposez pas cet appareil la pluie ou l'humidit. WARNUNG! Um das Risiko des elektrischen Schlages zu verringern, setzen Sie diesen Apparat nicht Regen oder Feuchtigkeit aus. Save these instructions Compliance of this equipment is confirmed by the following label that is placed on the equipment:

USA & Canada Compliance FCC Part 15, Subpart B / ICES-003Unintentional Emissions Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules and Industry Canada ICES-003. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver Increase the separation between the equipment and receiver. is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC rules and Industry Canada ICES-003. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. IMPORTANT! Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. IMPORTANT! Tous les changements ou modifications pas expressment approuvs par la partie responsable de la conformit ont pu vider lautorit de lutilisateur pour actionner cet quipement. Ferrite clamp installation. When installing a Control4 7 In-Wall Touch Screen, also install the enclosed ferrite clamp as described in this document. Ethernet cable. Install the ferrite clamp on the Ethernet cable no farther than 6 inches from the Ethernet jack. Compliance of this equipment is confirmed by the following label that is placed on the equipment:

FCC Part 15, Subpart C / RSS-210 Intentional Emissions Interference Statement Compliance of this equipment is confirmed by the following certification numbers that are placed on the equipment:

Notice: The term FCC ID: and IC before the certification number signifies that FCC and Industry Canada technical specifications were met. FCC ID: R33C4TW7C0 IC: 7848A-C4TW7C0 This equipment must be installed by qualified professionals or contractors in accordance with FCC Part 15.203 & IC RSS-210, Antenna Requirements. Do not use any antenna other than the one provided with the unit. RF Radiation Exposure Statement This equipment complies with the FCC/IC radiation exposure limits set fourth for portable transmitting devices operation in an uncontrolled environment. End users must follow the specific operating instructions to satisfy RF exposure compliance. The equipment should only be used or installed at locations where there is normally at least a 20cm separation between the antenna and all persons. This transmitter must not be co-located or operation in conjunction with any other antenna or transmitter. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. European Compliance Conformity of the equipment with the guidelines below is attested by the application of the CE mark. Manufacturers Name:

Manufacturers Address:

CE Declaration of Conformity CONTROL4 CORPORATION 11734 S. ELECTION ROAD SUITE 200 SALT LAKE CITY UT 84020 USA EU Representative Name: CONTROL4 EMEA LIMITED EU Representative Address: UNIT3, GREEN PARK BUSINESS CENTRE SULTON-ON-THE FOREST YORK YO61 IET, UNITED KINGDOM Touch Screen Contol4 C4-TW7C0-XX Product Name(s):

Brand:

Model(s):

Product Standard(s) to which Conformity of the Council Directive(s) is declared:

EMC - 2004/108/EC Electromagnetic Compatibility (EMC) Directive:

(Emissions) EN 55022:2010, (Immunity) EN 55024:1998, EN 301 489-1:2008, EN 301 489-

17:2009, EN 61000-3-2:2004 & EN 61000-3-3:2002 Safety 206/95/EC Low Voltage Directive (LVD):

EN 60950-1:2006 (2nd Edition) Telecom & Radio - 1999/5/EC Radio equipment and Telecommunications Terminal Equipment (R&TTE) Directive:

EN 300 328 V1.7.1 (2006-10) RoHS - 2002/95/EC Restriction of the Use of certain Hazardous Substances in Electrical and Electronic Equipment (EEE) & WEEE - 2002/96/EC Waste of Electrical and Electronic Equipment (EEE). We, the undersigned, hereby declare that the equipment specified above conforms to the above directives and standards. Date of Issue: June 5, 2012 Legal Representative Signature Roger Midgley Sr. Regulatory Compliance Engineer National Restrictions This product may be used in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:

Ce produit peut tre utilis dans tous les pays de l'UE (et dans tous les pays ayant transposs la directive 1999/5/CE) sans aucune limitation, except pour les pays mentionns ci-dessous:

Questo prodotto utilizzabile in tutte i paesi EU (ed in tutti gli altri paesi che seguono le direttive EU 1999/5/EC) senza nessuna limitazione, eccetto per i paesii menzionati di seguito:

Das Produkt kann in allen EU Staaten ohne Einschrnkungen eingesetzt werden (sowie in anderen Staaten die der EU Direktive 1999/5/CE folgen) mit Aunahme der folgenden aufgefhrten Staaten:

France In case the product is used outdoors, the output power is restricted in some parts of the band. See Table 1 below or check http://www.arcep.fr/ for more details. Dans la cas d'une utilisation en extrieur, la puissance de sortie est limite pour certaines parties de la bande. Voir la table ci-dessous ou visitez http://www.arcep.fr/ pour de plus amples details Table 1 Applicable Power Levels in France Location Frequency Range (MHz) Power (EIRP) Indoor (No restrictions) 2400-2483.5 100 mW (20 dBm) Outdoor 2400-2454 2454-2483.5 100 mW (20 dBm) 10 mW (10 dBm) Recycling Control4 understands that a commitment to the environment is essential for a health life and sustainable growth for future generations. We are committed to supporting the environmental standards, laws, and directives that have been put in place by various communities and countries that deal with concerns for the environment. This commitment is represented by combining technological innovation with sound environmental business decisions. WEEE Compliance Control4 is committed to meeting all requirements of the Waste Electrical and Electronic Equipment (WEEE) directive (2002/96/EC). The WEEE directive requires the manufacturers of electrical and electronic equipment who sell in EU countries: (1) label their equipment to notify customers that it needs to be recycled, and (2) provide a way for their products to be appropriately disposed of or recycled at the end of their product lifespan. For collection or recycling of Control4 products, please contact your local Control4 representative or dealer. Australia / New Zealand Compliance Compliance of this equipment is confirmed by the following label that is placed on the equipment:

About this Document Copyright 2012 Control4 Corporation. All rights reserved. Control4 and the Control4 logo are registered trademarks or trademarks of Control4 Corporation in the United States and/or other countries. Part Number 200-00292 Rev A, 6/5/2012