FCC ID: R33C4LGWM WIFI MODULE

7" and 10" T3 Series In-Wall Touch Screen Installation Guide Accessories available for purchase PoE. Control4 Power over Ethernet Injector, sold separately

(AC-POE1-B). Back box options (sold separately)Metal and plastic, for new construction or retrofit installations. 7" and 10" In-Wall Touch Screen Back Box Kits - New Construction 7" and 10" In-Wall Touch Screens Wall Box, New Construction, Plastic (C4-NWB57C-P) 7" and 10" In-Wall Touch Screens Wall Box, New Construction, Metal (C4-NWB57C-M) 7" and 10" In-Wall Touch Screen Back Box Kit - Retrofit 7" and 10 In-Wall Touch Screens Wall Box, Retrofit, Plastic (C4-RWB57C-P) 7" and 10" In-Wall Touch Screens Wall Box, Retrofit, Metal (C4-RWB57C-M) For back box installation details, see:

7" or 10" In-Wall Touch Screen Wall Box Installation Guide-New Construction 7", or 10" In-Wall Touch Screen Wall Box Installation Guide-Retrofit Supported models C4-WALL7-BL C4-WALL7-WH C4-WALL10-BL C4-WALL10-WH 7" T3-7 In-Wall Touch Screen, Black 7" T3-7 In-Wall Touch Screen, White 10" T3-10 In-Wall Touch Screen, Black 10" T3-10 In-Wall Touch Screen, White Introduction The Control4 T3-7 (7") and T3-10 (10") In-Wall Touch Screens offer complete system control in an elegant and compact design. The touch screens are equipped with a full capacitive screen, audio and video Intercom (with the built-in camera) using SIP, and more. This touch screen works great in either new construction or retrofit installations. For power and network connectivity, choose from three options:

Ethernet with PoEThe Ethernet network connection is provided through the PoE Injector. No additional wiring is needed. Ethernet with ACConnect the touch screen to one of the RJ-45 LAN ports on the gateway/router using the RJ-45 Ethernet cable. AC power is used to power the touch screen. WiFi with ACThe internal WiFi will communicate with the LANs WAP. If the LAN has a WAP set up, no additional network wiring is needed. AC power is used to power the touch screen. Note: 802.11b is not recommended for Video Intercom. We recommend using Wireless-N. See Specifications and Power and Network Installation Options for more information. Box contents 7" or 10" T3-7/T3-10 In-Wall Touch Screen Power box (to power the touch screen) (005-00065) Two screws (to attach the power box) Touch Screen removal tool Four adhesive-backed foam pads Warranty card 11 Warnings Warning! The touch screen must be protected by an external circuit breaker or a fuse rated at 6A maximum when used in Europe. AVERTISSEMENT ! Pour rduire le risque du feu ou de choc lectrique, nexposez pas cet appareil la pluie ou lhumidit. Warning! Do not place the touch screen near sources of heat or expose to direct sunlight for an extended period of time. AVERTISSEMENT ! Ne placez pas lunit prs des sources de chaleur ou exposition pour diriger la lumire du soleil pendant une priode prolonge. Warning! Install in accordance with all national, state, and local electrical codes. AVERTISSEMENT ! Installez selon tous les national, tat, et codes lectriques locaux. Warning! This product generates heat. The room must have adequate ventilation or the ability to dissipate heat effectively. AVERTISSEMENT ! Ce produit produit de la chaleur. La salle doit avoir ventilation proportionne ou la capacit dabsorber la chaleur efficacement. Warning! This product must be grounded in accordance with the National Electrical Code (NEC) requirements. AVERTISSEMENT ! Ce produit doit tre fondu selon les conditions lectriques nationales de code (NEC). Warning! Use this product only in dry locations. AVERTISSEMENT ! Employez ce produit seulement dans des endroits secs. Caution! This product is for residential use only. AVERTISSEMENT ! Ce produit est pour lusage rsidentiel ou commercial seulement. Caution! Do not use pens or sharp objects to navigate or make selections on the touch screen. To select an item or scroll through a list, use your fingertip. AVERTISSEMENT ! Nemployez pas les stylos ou les objets pointus pour diriger ou pour faire des choix sur lcran. Pour choisir un article ou un rouleau par une liste, employez votre bout du doigt. Caution! Improper use or installation can cause DAMAGE OF PROPERTY. AVERTISSEMENT ! Lutilisation ou linstallation inexacte peut causer DAMAGE DE PROPRIT. Important! Using this product in a manner other than outlined in this document voids your warranty. Further, Control4 is NOT liable for any damage incurred with the misuse of this product. See Warranty. Important ! Utilisant ce produit en quelque sorte autre que dcrit dans ce document vide votre garantie. De plus, Control4 nest pas responsable daucun dommage encouru avec labus de ce produit. Voyez que Warranty. For more information, visit the Products pages at dealer.control4.com. Specifications and requirements Specifications Model Numbers C4-WALL7-BL, C4-WALL7-WH, C4-WALL10-BL, C4-WALL10-WH Screen Resolution: 1280 800 Camera: 720p Network Ethernet or WiFi (802.11b/g/n [2.4 GHz]) Security: WEP, WPA/WPA2 PSK, 801.1x EAP, PEAP Notes: (1) Intercom usage. 802.11b is not recommended for Video Intercom. (2) Wireless-N is recommended for Video Intercom. Even with Wireless-N, broadcasting to several devices will degrade Video Intercom response time and images. Broadcasting to additional devices will further degrade performance. See Wireless Network Limitations. Power supply PoE (IEEE802.3af) 13 W peak 100-240VAC, 50/60 Hz Operating temperature 32 ~ 104F (0 ~ 40C) Storage temperature 4 ~ 158F (-20 ~ 70C) Dimensions (W H D) 7" model: 6.9" 5.0" 0.53" (175 127 13 mm) 10" model: 9.4" 6.5" 0.53" (239 165 13 mm) Back box: 2.7" 4.1" 2.4" (68 104 61 mm) Power box: 2.8" 4.5" 1.8" (71 114 46 mm) Weight (with mid-box) Shipping Weight 7" model: 0.9 lbs. (0.41 kg) 10" model: 1.5 lbs. (0.68 kg) 7" model: 1.5 lbs (0.68 kg) 10" model: 2.1 lbs (0.95 kg) Requirements A controller fully installed and configured with Control4 OS2.7.0 or later. Control4 7" or 10" In-Wall Touch Screen custom back box installed. See Accessories. If using Ethernet with PoE power:

Ethernet network installed and available that includes a gateway/router/switch Control4 PoE Injector (model #AC-POE1-B) or another third-party PoE Injector or switch (UL/ANSI certified). Two Ethernet CAT5/6 cables: (1) one that runs from the Ethernet gateway/router/switch to the PoE Injector/switch and (2) one that runs from the PoE Injector/switch to the Ethernet connection in the touch screens back box. If using Ethernet with AC power:

Ethernet network installed and available that includes a gateway/router/switch Access to in-wall AC power (neutral connection required) One Ethernet CAT5/6 cable that runs from the Ethernet gateway/router/switch to the touch screen A 14-gauge electrical wire long enough to pull between the touch screen and the power source If using wireless with AC power:

Wireless network (WiFi 802.11b/g/n) installed and available with a wireless access point (WAP). Security can be WEP, WPA/WPA2 PSK, 801.1x EAP, PEAP. Access to in-wall AC power (neutral connection required) A 14-gauge electrical wire long enough to pull between the touch screen and the power source 2 Front view Figure 1: Front view BA C D A LEDIndicates when the camera is on. B CameraFor video intercom calls. C Display7" or 10" diagonal, capacitive touch screen with 1280 800 resolution. D SpeakersProvide stereo audio. Back view Figure 2: Back view A B A Ribbon cable-Provides data and power connection to the touch screen from the power box. B Mounting ringFits into the power box. Top view Figure 3: Top view (with power box attached) A CB A MicrophoneRecords audio. B RESETPress and hold a straightened paper clip into this hole to reset the touch screen to factory defaults. C Power buttonPress to turn off the touch screen, or press and hold to reboot. 3 Touch screen placement Place the touch screen in a convenient location at eye level, typically near the entrance of the room, approximately 57 to 61 inches (145 cm to 155 cm) from the floor (Figure 3). Note: Consider the camera on the panel and the height of the people in the home who will use the camera for Video Intercom. Figure 3: Touch screen placement Touch screen AC power

(unless using PoE) LED indicator The LED on the touch screen indicates the camera status of the camera and booting information as described in the next table. Camera/LED color state Touch screen status Off Green Camera is off Camera is on Green (blinking slowly) Touch screen is booting Installation Warning! Before installing the touch screen, switch off the circuit breaker or remove the fuse from the fuse box. AVERTISSEMENT ! Pour lendroit o vous installez lcran tactile, coupez le disjoncteur ou enlevez le fusible de la bote de fusible. Important! Before you can complete the instructions below, you must have a 7" or 10" Touch Screen back box installed according to the documentation provided in the back box kit. See Accessories for details. Important ! En coupant louverture pour la bote de mur, ne coupez pas louverture trop grande. Soyez conservateur et agrandissez-avec prcaution la comme ncessaire. Voyez que <<Accessories>>. Important! When cutting the opening for the back box, do not cut the opening too large. Be conservative and cautiously enlarge it as needed. Important ! En coupant louverture pour la bote de mur, ne coupez pas louverture trop grande. Soyez conservateur et agrandissez-avec prcaution la comme ncessaire. Power and network installation options This device uses an Ethernet or WiFi network connection, and can be powered using PoE or AC power. Choose one of the following options to install the power and network communication. Caution! Do not attempt to use PoE and AC power at the same time. Choose only one power option. ATTENTION ! Ne pas tenter dutiliser PoE et AC en mme temps. Choisir une seule option dalimentation. Option 1: Ethernet connection with PoE PoE supplies DC power on the Ethernet cable using a PoE Injector (model #AC-POE1-B) or a third-party PoE solution to provide the touch screen with power and a network connection. The touch screen works with the Control4 PoE Injector or a third-

party PoE Injector. To set up your PoE and Ethernet connection with a PoE Injector:

1 Attach the PoE Injector according to the instructions in your PoEs installation guide if provided. Control4 PoE Injector instructions are provided later in this document. 2 Pull the Ethernet cable from that location to where you want to install the touch screen. Figure 4: Ethernet with PoERequires Ethernet connection to PoE injector Wireless Network Limitations: Many WiFi Access Points handle Multicasts (WiFi simultaneously sent to multiple devices, for example, when the touch screen broadcasts video to all stations) by slowing down transmission speed to the 1 Mb basic rate. This can cause overall WiFi congestion in the WiFi network during the broadcast. Video Intercom response times and images may degrade at each device. If a home requires a large number of WiFi Video Intercom devices, ensure that you have a robust WiFi network (possibly consisting of multiple access points). Figure 6: WiFiRequires AC Power and WAP Power installation Prepare the plastic power box for installation into the back box by inserting either the Ethernet cable or the AC power cable into the power box, and then follow the instructions. Connecting PoE Connect the PoE injector to power and the network, and then connect it to the power box. To install a Control4 PoE injector:

1 Connect the Control4 PoE injector to an AC outlet using the power cord. 2 Connect one of the RJ-45 LAN ports on the gateway/router/

switch to the PoE Injectors LAN port using CAT5/6 Ethernet cable. 3 Connect the PoE Injectors PWR LAN-OUT port to the RJ-45 Ethernet cable that will be connected to the touch screens power box. 4 Pull the Ethernet cable through the top left hole of the back box, then plug it into the Ethernet jack on the top back of the power box (Figure 7). Option 2: Ethernet connection with AC The Ethernet is connected directly to the switch (Figure 5). This power connection requires both neutral and hot connections. Figure 5: EthernetRequires a connection to Ethernet and AC power Option 3: WiFi connection with AC Place the touch screen above a power source, for example, an outlet. Ensure that you have WiFi in the home (Figure 6). Notes: (1) Video Intercom. Although this device supports 802.11b/g/n, 802.11 b is not recommended for Video Intercom use. (2) We recommend Wireless-N for Video Intercom. See the Composer Pro User Guide for details about the touch screens properties. 4 Figure 7: Insert Ethernet cable into power box Figure 9: Connect AC power Neutral (N) Line (L) 4 Cap the ground wire from the wall if you are using a plastic back box. Attach the ground wire to the back box if using a metal back box. Attach the power box and touch screen To attach the power box and touch screen:

1 Align and bend the wires carefully to fit them inside the back box. 2 Align slide the power box into the back box, then secure the power box to the back box using the two screws provided. Figure 10: Secure power box to back box Note: Overtightening the power box screws can warp the box and make it difficult to attach the touch screen. 3 Straighten out the ribbon cable taped to the back of the touch screen, then plug it into the ribbon cable port in the power box. To make sure its securely connected, press it into the port until the two locking tabs close onto the connector. 5 Go to Attach the power box and touch screen below. Connecting standard Ethernet To connect to a wired network:

1 Pull the in-wall Ethernet cable through the top left hole of the back box, then plug it into the Ethernet jack on the top back of the power box (Figure 8). Figure 8: Insert Ethernet cable into power box 2 Go to Attach the power box and touch screen below. Connecting AC power The steps below represent a typical U.S. installation. 1 Connect the wires to the AC power source for the touch screen according to national and local electrical codes. Installation may require alternative wires and the use of a terminal block. 2 Thread the power cable through the upper back hole of the back box to the terminal block (Figure 7). 3 Strip the black and white power wire ends to 1/4" as necessary. Using a flat-head screwdriver, loosen the screws on the power boxs terminal block and connect the power wires to each terminal (Figure 9). 5 Figure 11: Attach ribbon cable to the power box 5 Tap OK. Add and configure in Composer Pro After the touch screen is installed and appears on the home network, use Composer Pro to add it to the Control4 system and configure it. Use the Composer Pro System Design and Connections views to add and configure this device. To add and configure a T3 touch screen to a project:

1 Add the T3-T7 or T3-T10 In-Wall Touch Screen driver to your project. 2 To configure the properties, click System Design. 3 In the project tree, select the T3 7" or T3 10" In-Wall Touch Screen. 4 View and change the properties in the Properties pane as needed. Properties include:

Network ConnectionReports the touch screens current network connection type. Back LightUse the arrows or type numbers to set the light level, then click Set. Advanced properties include:

Enable CameraAllows you to enable or disable the camera. Intercom (nested under the touch screen) properties:

AppearanceSelect to hide the touch screen from appearing in Navigators as an available device. BehaviorSelect the modes you want this touch screen to support. Audio ControlSelect the volume of individual audio settings. Sip InformationInformation for integrating the touch screen into your SIP/VoIP system. Custom ButtonsSelect to enable and label the two available custom buttons. Alternate CameraSelect to use an external camera for the video associated with the touch screen, for example, a security camera mounted to the side of the entrance and pointing at the door. 4 For easiest installation, angle the top of the touch screen toward the wall, insert the top tabs of the mounting ring into the power box, then press the bottom of the touch screen into place. Configuration Configure the touch screen for wireless (optional) 1 After initialization, tap Network. The network configuration page opens. 2 Under Wireless, tap Enable, then tap the network you want to connect to. Or, if you dont see the network you want:

a Tap Other. b Tap the Network Name field, type the network name with the on-screen keyboard, then tap Done. c Tap the Security field, then select a type of security to use. d Tap the Key field, type the network password with the on-

screen keyboard, then tap Done. e Tap Connect. Notice that the IP settings change. The IP address is set to DHCP by default. 3 (Optional) If you need to set a static IP address:

a On the Network page, tap Show advanced options, scroll down and tap DHCP, then tap Static. b Select each box one at a time and use the on-screen keyboard to type the IP Address, Subnet Mask, Default Gateway, Preferred DNS, and Alternate DNS. c Tap Done. 4 Tap OK to return to the Network page. You can now connect to a Director. 6 Troubleshooting Boot up time When the device is booting up, it may take 30 seconds or longer before the Green LED turns on. When it turns on, it blinks slowly for a time and then turns off. After that, youll see an image on the touch screen. Unresponsive screen If the cameras LED blinks on and off for more than 30 seconds, the device may need to be power cycled. If power cycling doesnt solve the problem, the touch screen may need to be restored to factory defaults. To power cycle the touch screen:

Regulatory/Safety Information To review regulatory information for your particular Control4 products, see the information located on the Control4 website at:

ctrl4.co/reg. Warranty Visit www.control4.com/warranty for details. 1 Press and hold the

(power) button for several seconds until the touch screen turns off. 2 Press and release the

(power) button again to turn on. To restore to factory defaults:

1 On the touch screens main screen, tap Settings, System Information, then Restore.

- OR -

Insert a straightened paper clip into the RESET hole on the top of the touch screen, then press and hold it for several seconds until the screen resets. Removing the touch screen from the wall To remove the touch screen:

1 Hold the removal tool flat against the wall, centered directly beneath the touch screen, then slide it upward between the wall and touch screen. 2 While pressing the tool up as far as it will go, carefully pull the touch screen away from the wall. Additional resources The following resources are available for more support. Control4 Knowledgebase and forums Control4 Technical Support Control4 website: www.control4.com Composer documentation in online help or PDF formats, available on the Dealer Portal under Resources control4.com | 888.400.4070 Copyright 2015, Control4 Corporation. All rights reserved. Control4, the Control4 logo, the 4-ball logo, 4Store, 4Sight, Control My Home, Everyday Easy, and Mockupancy are registered trademarks or trademarks of Control4 Corporation in the United States and/or other countries. All other names and brands may be claimed as the property of their respective owners. All specifications subject to change without notice. 7 B 200-00387-B 2015-03-04 MS Regulatory Compliance & Safety Information for Contol4 Model C4-WALL7-XX & C4-

WALL10-XX. Electrical Safety Advisory Scurit lectrique consultatif Important Safety Information Informations de scurit importantes Read the safety instructions before using this product. Lisez les consignes de scurit avant d'utiliser ce produit. 1. Read these instructions. 1. Lisez ces instructions. 2. Keep these instructions. 2. Conservez ces instructions. 3. Heed all warnings. 3. Respectez tous les avertissements. 4. Follow all instructions. 4. Suivez toutes les instructions. 5. Do not use this apparatus near water. 5. Ne pas utiliser cet appareil prs de l'eau. 6. Clean only with dry cloth. 6. Nettoyez-le uniquement avec un chiffon sec. 7. Do not block any ventilation openings. Install in accordance with the manufacturers instructions. 7. Ne pas bloquer les ouvertures de ventilation. Installer conformment aux instructions du fabricant. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 8. Ne pas installer prs de sources de chaleur telles que des radiateurs, registres de chaleur, poles, ou autres appareils (incluant les amplificateurs) qui produisent de la chaleur. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 9. Ne pas contourner le dispositif de scurit de la fiche polarise ou de mise la terre. Une fiche polarise possde deux lames dont une plus large que l'autre. Une fiche de terre a deux lames et une troisime broche de terre. La lame large ou la troisime broche est fournie pour votre scurit. Si la fiche fournie ne s'adapte pas votre prise, consultez un lectricien pour le remplacement de la prise obsolte. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 10. Protgez le cordon d'alimentation ne soit pitin ou pinc, en particulier au niveau des fiches, des prises et au point o il sort de l'appareil. 11. Only use attachments/accessories specified by the manufacturer. 11. Utilisez uniquement des fixations / accessoires spcifis par le fabricant. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 12. Utilisez uniquement avec le chariot, le socle, le trpied, le support ou la table spcifis par le fabricant ou vendu avec l'appareil. Lorsque vous utilisez un chariot, soyez prudent lorsque vous dplacez l'ensemble chariot / appareil pour viter des blessures dues au renversement. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. This equipment uses AC power which can be subjected to electrical surges, typically lightning transients which are very destructive to customer terminal equipment connected to AC power sources. The warranty for this equipment does not cover damage caused by electrical surge or lightning transients. To reduce the risk of this equipment becoming damaged it is suggested that the customer consider installing a surge arrestor. 13. Dbranchez cet appareil pendant les orages ou lorsqu'il n'est pas utilis pendant de longues priodes de temps. Cet quipement utilise la puissance AC qui peuvent tre soumis des surtensions lectriques, la foudre gnralement transitoires qui sont trs destructives envers les quipements terminaux connects des sources d'alimentation CA. La garantie de cet appareil ne couvre pas les dommages causs par les surtensions lectriques ou transitoires de foudre. Pour rduire le risque de cet quipement devient endommag, il est suggr que le client envisager l'installation d'un limiteur de surtension. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 14. Confiez toutes les rparations un personnel qualifi. Une rparation est ncessaire lorsque l'appareil a t endommag de quelque faon que ce soit le cordon d'alimentation ou la fiche est endommag, du liquide a t renvers ou si des objets sont tombs dans l'appareil, l'appareil a t expos la pluie ou l'humidit, ne fonctionne pas normalement , ou s'il est tomb. 15. Use the circuit breaker to disconnect the apparatus from the AC mains. The circuit breaker shall remain readily accessible. 15. Utiliser le disjoncteur pour dconnecter l'appareil de l'alimentation secteur. Le disjoncteur doit rester facilement accessible. 16. To completely disconnect unit power from the AC mains, turn off the circuit breaker. To reconnect power, turn on the circuit breaker following all safety instructions and guidelines. 16. Pour couper entirement l'alimentation appareil de l'alimentation secteur, teignez le disjoncteur. Pour rtablir le courant, mettez le disjoncteur aprs les consignes de scurit et des lignes directrices. 17. This product relies on the buildings installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 20A. 17. Ce produit repose sur l'installation des btiments pour les courts-circuits (surintensit) de protection. Assurez-vous que le dispositif de protection est assigne ne dpassant pas:

20A. 18. CAUTION: As with all batteries, there is a risk of explosion or personal injury if the battery is replaced by an incorrect type. Dispose of used battery according to the instructions of the battery manufacturer and applicable environmental guidelines. Do not open, puncture or incinerate the battery, or expose it to conducting materials, moisture, liquid, fire or heat above 54 C or 130 F. 18. ATTENTION: Comme avec toutes les batteries, il ya un risque d'explosion ou de blessure si la batterie est remplace par un type incorrect. liminez les batteries usages selon les instructions du fabricant de la batterie et applicables des directives environnementales. Ne pas ouvrir, percer ou incinrer la batterie, ou de l'exposer des matriaux conducteurs, de l'humidit, du liquide, un incendie ou une temprature suprieure 54 C ou 130 F. 19. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. 19. N'introduisez jamais d'objets d'aucune sorte dans ce produit travers les fentes du botier car ils pourraient toucher des points de tension dangereux ou court-circuiter des pices qui pourraient entraner un incendie ou un choc lectrique. 20. This product can interfere with electrical equipment such as tape recorders, TV sets, radios, computers and microwave ovens if placed in close proximity. 20. Ce produit peut interfrer avec des appareils lectriques tels que les magntophones, tlviseurs, radios, ordinateurs et fours micro-ondes si placs proximit. The lightning flash and arrow head within the triangle is a warning sign alerting you of dangerous voltage inside the product L'clair et la flche dans le triangle est un signe d'alerte pour vous avertir d'une tension dangereuse l'intrieur du produit Caution: To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel. Attention: Pour rduire le risque de choc lectrique, ne pas retirer le couvercle

(ou l'arrire). Aucune pice rparable par l'utilisateur. Confiez l'entretien un personnel qualifi. The exclamation point within the triangle is a warning sign alerting you of important instructions accompanying the product. Le point d'exclamation dans un triangle est un signe d'avertissement vous signale des instructions importantes accompagnant le produit. See marking on bottom / back of product Voir le marquage sur les bas / dos du produit Warning!: To reduce the risk of electrical shock, do not expose this apparatus to rain or moisture AVERTISSEMENT! Pour rduire le risque de choc lectrique, n'exposez pas cet appareil la pluie ou l'humidit. Save these instructions Conservez ces instructions Compliance of this equipment is confirmed by the following label that is placed on the equipment:

Conformit de cet appareil est confirm par le symbole suivant qui est plac sur l'quipement:

USA & Canada Compliance FCC Part 15, Subpart B Unintentional Emissions Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver Increase the separation between the equipment and receiver. is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Partie 15, sous-section B Unintentional Dclaration sur les interfrences des missions Cet quipement a t test et jug conforme aux limites tablies pour un dispositif numrique de classe B, conformment la Partie 15 des rglements de la FCC. Ces limites sont conues pour fournir une protection raisonnable contre les interfrences nuisibles lorsque l'quipement est utilis dans une installation rsidentielle. Cet quipement gnre, utilise et peut mettre de l'nergie rayonnent frquence et, s'il n'est pas install et utilis conformment aux instructions, il peut causer des interfrences nuisibles aux communications radio. Cependant, il n'existe aucune garantie que des interfrences ne se produiront pas dans une installation particulire. Si cet quipement provoque des interfrences nuisibles la rception radio ou tlvision, ce qui peut tre dtermin en mettant l'quipement hors et sous tension, l'utilisateur est encourag essayer de corriger l'interfrence par une ou plusieurs des mesures suivantes:

Rorienter ou dplacer l'antenne de rception. Augmenter la distance entre l'quipement et le rcepteur. Connecter l'quipement une prise sur un circuit diffrent de celui sur lequel le rcepteur est branch. Consulter le revendeur ou un technicien radio / tlvision qualifi pour obtenir de l'aide. This device complies with part 15 of the FCC rules and Industry Canadas licence-exempt RSS-

GEN. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme partie 15 des rgles de la FCC et aux RSS-GEN d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. IMPORTANT! Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. IMPORTANT! Tous les changements ou modifications pas expressment approuvs par la partie responsable de la conformit ont pu vider lautorit de lutilisateur pour actionner cet quipement. FCC Part 15, Subpart C / RSS-210 Intentional Emissions Interference Statement Compliance of this equipment is confirmed by the following certification numbers that are placed on the equipment:

Notice: The term FCC ID: and IC: before the certification number signifies that FCC and Industry Canada technical specifications were met. The FCC ID: and IC: numbers listed below are for the WiFi module that was certified as a Limited Modular Approval. FCC ID: R33C4LGWM IC: 7848A-C4LGWM The end user equipment that contains the certified WiFi module are labeled with the following on the outside of the equipment:

Contains FCC ID: R33C4LGWM Contains IC: 7848A-C4LGWM This equipment must be installed by qualified professionals or contractors in accordance with FCC Part 15.203 & IC RSS-210, Antenna Requirements. Do not use any antenna other than the one provided with the unit. FCC Partie 15, sous-partie C / RSS-210 Dclaration volontaire des missions interfrences Conformit de cet appareil est confirm par les chiffres de certification suivants qui sont placs sur l'quipement:

Avis: Le terme FCC ID:" et "IC:" devant le numro de certification signifie que les spcifications techniques de la FCC et d'Industrie Canada ont t respectes. La FCC ID: et IC: numros indiqus ci-dessous sont pour le module WiFi qui a t certifie en tant que Approbation limite modulaire. FCC ID: R33C4LGWM IC: 7848A-C4LGWM L'quipement d'utilisateur final qui contient le module WiFi certifie sont marqus par le suivant l'extrieur de l'objet:

Contient ID FCC: R33C4LGWM Contient IC: 7848A-C4LGWM Cet quipement doit tre install par des professionnels qualifis ou entrepreneurs conformment aux normes FCC partie 15.203 & IC RSS-210, Exigences d'antenne. Ne pas utiliser une antenne autre que celui fourni avec l'appareil. RF Radiation Exposure Statement This equipment complies with the FCC/IC radiation exposure limits set fourth for portable transmitting devices operation in an uncontrolled environment. End users must follow the specific operating instructions to satisfy RF exposure compliance. The equipment should only be used or installed at locations where there is normally greater than a 20cm separation between the antenna and all persons. This transmitter must not be co-located or operation in conjunction with any other antenna or transmitter. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. Dclaration d'exposition aux radiations RF Cet quipement est conforme aux limites FCC / IC d'exposition aux rayonnements dfinies quatrime opration appareils portables transmettre dans un environnement non contrl. Les utilisateurs finaux doivent suivre les instructions de fonctionnement spcifiques pour satisfaire la conformit aux expositions RF. L'quipement ne doit tre utilis ou install des endroits o il est normalement suprieure une sparation de 20 cm entre l'antenne et toute personne. Cet metteur ne doit pas tre co-localiss ou fonctionnement en conjonction avec une autre antenne ou un autre metteur. Tout changement ou modification non expressment approuv par la partie responsable de la conformit pourraient annuler l'autorit de l'utilisateur utiliser cet quipement. European Compliance Conformity of the equipment with the guidelines below is attested by the application of the CE mark. Manufacturers Name:

Manufacturers Address:

CE Declaration of Conformity CONTROL4 CORPORATION 11734 S. ELECTION ROAD SUITE 200 SALT LAKE CITY UT 84020 USA EU Representative Name: CONTROL4 EMEA LIMITED EU Representative Address: UNIT3, GREEN PARK BUSINESS CENTRE SULTON-ON-THE FOREST YORK YO61 IET, UNITED KINGDOM In-Wall Touch Screen Contol4 C4-WALL7-XX & C4-WALL10-XX Product Name(s):

Brand:

Model(s):

Product Standard(s) to which Conformity of the Council Directive(s) is declared:

EMC - 2004/108/EC Electromagnetic Compatibility (EMC) Directive:

(Emissions) EN 55022:2010, (Immunity) EN 55024:2010, EN 301 489-1 V1.9.2 (2011-09), EN 301 489-17 V2.2.1 (2012-09), EN 61000-3-2:2006 + A1:2009 + A2:2009 & EN 61000-3-3:2008 Safety 206/95/EC Low Voltage Directive (LVD):

EN 60950-1:2006/A11:2009/A1:2010/A12:2011 Telecom & Radio - 1999/5/EC Radio equipment and Telecommunications Terminal Equipment (R&TTE) Directive:

EN 300 328 V1.8.1 RoHS - 2011/65/EU Restriction of the Use of certain Hazardous Substances in Electrical and Electronic Equipment (EEE) & WEEE - 2002/96/EC Waste of Electrical and Electronic Equipment (EEE). We, the undersigned, hereby declare that the equipment specified above conforms to the above directives and standards. Date of Issue: March 10, 2015 Legal Representative Signature Roger Midgley Sr. Regulatory Compliance Engineer Recycling Control4 understands that a commitment to the environment is essential for a health life and sustainable growth for future generations. We are committed to supporting the environmental standards, laws, and directives that have been put in place by various communities and countries that deal with concerns for the environment. This commitment is represented by combining technological innovation with sound environmental business decisions. WEEE Compliance Control4 is committed to meeting all requirements of the Waste Electrical and Electronic Equipment (WEEE) directive (2002/96/EC). The WEEE directive requires the manufacturers of electrical and electronic equipment who sell in EU countries: (1) label their equipment to notify customers that it needs to be recycled, and (2) provide a way for their products to be appropriately disposed of or recycled at the end of their product lifespan. For collection or recycling of Control4 products, please contact your local Control4 representative or dealer. About this Document Copyright 2015 Control4 Corporation. All rights reserved. Control4 and the Control4 logo are registered trademarks or trademarks of Control4 Corporation in the United States and/or other countries. Part Number 200-00? Rev A, 3/10/2015