Convoy Technologies Wireless video and audio transmitter MODEL :
CT-W1000KIT, CT-W1000KIT-MCN, CT-W1000TX, CT-W1000RX, 1490159, 1490161 contents 1 INTRODUCTION .............................................................................. 3 2 INSTALLATION ........................................................................... 3 3 USAGE INSTRUCTION........................................................................ 4 3 SPECIFICATIONS .............................................................................. 5 INTRODUCTION Convoy Wireless Module is a series of low cost and high performance digital Wireless transceiver module for wireless rearview, wireless camera applications which integrates MPEG4 codec , FHSS base band , RF transceiver ,AD&Flash, CVBS PAL/NTSC System input. PowerSupplyByCar 12V USAGE INSTRUCTION vehicle. flashing. flashing. 1. Ensure to follow above connection diagram to install the modules properly into your 2. LED light status (ON = POWER ON & CONNECTED, FLASHING= PAIRING MODE, OFF = POWER OFF or DISCONNECTED) 3. You may choose to perform a Pairing to re-establish connection between modules by procedure below:
Holding the center pairing button on Receiver Module until LED light constantly The connected Monitor Display will display PAIRING with 50 second count down. Holding the center pairing button on Transmitter Module until LED light constantly The connected Monitor Display will display SAVED DATA for successful Pairing and then camera image will be displayed. SPECIFICATION DC Characteristics POWER SUPPLY TX Current Consumption Environmental Specification Operating Temperature Storing Temperature Operating humidity BASEBAND SPEC. POWER ON Latency Resolution Frame Rate Video Codec TX Video in System RX Video out System Audio Codec Voice Sample Rate Voice Frequency Band ID / BIT SYSTEM Architecture Idle Screen Video Characteristics Video Output impedance Video Output Level Video Polarity Video Frequency Response Differential Gain Differential Phase S/N DC 12V TYPE:330Ma, Max.400Ma
-10~+60 C
-30~+85 C 85%RH 2SEC Max. RE TBD Max. SE/AV 100ms Max. RE TBD Max. SE/AV VGA/640X480 RE PAL:720X576/NTSC:720X480 SE/AV 30f/s NTSC:30f/s/PAL: 25f/s SE/AV MPEG4 PAL/NTSC Auto detection PAL/NTSC Auto detection MP3 1Channel 8KHz M RE/SE 48KHz AV 340Hz~3.4KHz RE/SE 20Hz~20KHz AV Pairing 22(4KK) ARM9(32Bit) SOC Blue Screen 75, Typ. 1Vp-p, Typ. NEGATIVE 5 dB, Max. 50Hz ~ 6MHz 5 %, Max 5 Deg., Max 50dB, Min Audio Audio Output impedance Audio Output Level S/N(340Hz ~ 3.4kHz) THD:(340Hz~ 3.4kHz,0.5p-p ) Outline Size Weight 200K, Typ. 5mv~0.5Vp-p, Typ. 63dB, Min 0.1 %, Max 147 x 87 mm 200g/box FCC Certification Requirements Caution: Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.